Search Documents

By Lei Wang, Qi Zheng, Xiao-kui Che

"The wastewater emitted by gold chemical industry contained vast of different heavy metal ion, such as Zn, Cu and Ni etc. Among them Zn is the main ion in the waste water which causes the serious environment pollution. A method of preparing a kind of resin which is used for the removal of Zn by magnetic adsorbent was developed and was applied in practice. This adsorbent is a chitosan made of a kind of Fe3O4-chitosan modified by epichlorohydrin. The adsorption capacity of the absorbent and it was concluded that under the laboratory conditions, the maximum adsorbing capacity of this adsorbent could be 287.58 mg/g. The absorbent was also applied in the wastewater emitted by a gold industry in Shandong province. Its performance was tested and the result showed that the concentration of Zn ion in the wastewater was reduced from 0.58 mg/L to 0.0174 mg/L. What is more, the adsorption rate could be more than 97% when the dosage was 100L/m3 after adsorbing for 1h. KEYWORDS Selective, preparation, laboratory experiments, industry experiment, comparation INTRODUCTION Currently, most gold chemistry use cyanide to leach gold ore. Many different metals participate to this reaction besides the gold ion in this processing, so that the composition of the water is very complex. The waste water emitted by gold chemistry industry contains large amount of heavy metals. Definitely, if it was discharged without any treatment, the water would threaten the environment. The recuperation of any ion in the water would mitigate the pollution. Ion exchange resin, which is an effective material to do the water treatment with low cost, became widely applicated in this field [Yu-jiao Wang,2013]. Different kinds of resin were developed and the influence factors such as pH, adsorption properties and selectivity for different ions were investigated [CA Cruz et al,2018; PawanKumar et al.2016; Y Zhang, et al,2010; and ShengingSun, Aiqin Wang, 2006;]. The waste water mentioned in this article has a high Zn concentration, so a magic resin for Zn adsorption selectively we designed was used to manage this water. And the recovery of Zn could not only contribute to pollution abatement but also a best way to settle a dispute to the short of Zn resource. So the article mainly describes the preparation and the application of a kind of magnetic adsorbent used for the removal of Zn both in laboratory and industry. The aim of this article is to compare the effect of this resin in industry and laboratory?"

Jan 1, 2018

By A. P. Purgin, M. G. Viduetsky, I. F. Garifulin

"The combined treatment process for mine, tailings storage facility, quarry, circulating, and waste water in the mining and metals industry brings together the conventional chemical treatment processes and pneumatic flotation cells of the KFM series. The key principle of the process is preparing the water for treatment by saturating with finely dispersed air bubbles in the flotation cell blowers. Gas-air lift dispersers located in the lower part of the cell body additionally saturate the cell’s contents with finely dispersed air. Due to the residual content of flotation agents in the treated water, hydroxide ion-air aggregates form at the aerator outlet, supporting the efficient precipitation of hydroxide ions of heavy non-ferrous metals, calcium and magnesium ions. This process was tested in the pilot plant KFM-180 with a raw (untreated) water capacity of up to 18 m3/h per 1 m3 of the flotation cell volume using a mixture of the tailings storage facility and mine water from JSC Safyanovo Copper. The treatment process included raw water treatment with lime, aeration in KFM cells, and filtration in a sorbent bed. The content of metal ions in the treated water is lower than in the feed water by a factor of up to 170,000 and approaches the standards: aluminum 0.016-0.02 mg/l, copper 0.0043-0.0045 mg/l, zinc 0.049-0.052 mg/l. circulating water of Soryin Tailings Storage Facility at JSC Svyatogor. The treatment process included raw water treatment with lime and alkali, aeration in KFM cells, and filtration in a sorbent bed. The content of metals in the treated water is lower than in the feed water by a factor of up to 9000: copper 0.022 mg/l, zinc 0.012 mg/l, iron 0.012 mg/l, manganese 0.015 mg/l, nickel 0.132 mg/l, arsenic 0.016 mg/l. Water hardness is significantly lower: calcium - 12.6 mg/l, magnesium - 1.1 mg/l. This process can be used in the treatment of mine, quarry, tailings storage facility, and circulating water at mining and non-ferrous metals projects."

Jan 1, 2018

By Valery V. Kostjuk, Victor. N. Bredikhin, Alexander I. Shevelev, Evgeny A. Kazban

"The investigations to improve the process data have been done in order to stabilize the functioning of drying units. The scheme of turnings preparation with centrifuging and subsequent thermal degreasing (tandem) is proposed. To improve the efficiency of the process the scheme of reclamation of the centrifuge fugate is developed with production of oil and service circulating water. Empirical dependences of the turnings temperature influence on the lubricant-coolants content in centrifuging are gained. When the turnings temperature is increased to 80 C the residual content of LC is decreased by 1.5%. The investigations aimed to improve the preparation of non-ferrous turnings have allowed to decrease the melting loss by 15-20%; to stabilize the process of thermal drying of turnings; to decrease sharply (by 60- 70%) the volume of LC combustion products; to reclaim the centrifuge fugate and produce oil and servicecirculating water.Non-ferrous turning and primarily aluminum and copper alloys turning is a stable source of secondary raw materials for metallurgical works.Direct by lubricant-coolants (LC) of various types: synthetic, semi synthetic, oily and emulsions.On the base of investigations concerning various methods of the non-ferrous turning processing the favorable one has been selected taking in to consideration the economy, ecology and quality of the finished product (alloy). Two-stage process is developed. The main idea of the process is the elimination of the lubricant-coolants (LC) to the limit specified in advance. The applied method is centrifuging with subsequent final elimination of LC by thermal method.Constant value of LC content at the inlet of the thermal unit excludes practically the oxidation of metal and as a consequence increases the output by 10 –15 % in metallurgical processing."

Jan 1, 2003

By A. F. Usov

A potential of electric pulse disintegration in benification used for primary deposits ores containing precious metals is shown. Of special significance is that PGM and gold grains, being highly plastic, are easily liberated and are not smeared on the disintegrated rock fragments surface. It al-lows gravity separation, which is less expensive and more efficient, to be used instead of chemical processing, which is expensive and environmentally faulty.

Jan 1, 2014

By Sarah K. DeBono, Alan J. Monaghan, Emmanuel V. Manlapig, Gregory J. Harbort

"The Jameson Cell is a type of flotation machine in which air and pulp are brought together in a vertical tube called a downcomer. Within the downcomer the air and pulp are dispersed into a dense foam of fine bubbles, which creates a favourable environment for bubble-particle collision and subsequent collection of hydrophobic particles. The intense collection zone within the downcomer can be considered similar to the zone between the rotor and stator in mechanical flotation cells.Research into the bubble-particle collision and fluid dynamics of mechanical cells rotor-stator zone has been limited by the difficulty of achieving accurate measurements in production sized machines. With the Jameson Cell the downcomer is largely external and separated from the flotation tank, allowing ready access to the primary contacting zone for measurement and analysis.An investigation has been undertaken into the operating characteristics of the downcomer relating to bubble-particle collision. An effective mapping of the downcomer has been made through measurements of void fraction and bubble size taken across cross sections of the downcomer. Analysis of these measurements has provided an interpretation of the variations in the air and fluid dynamics, bubble size and distribution throughout the downcomer chamber."

Jan 1, 2003

By M. Pischtschan, S. Belz, M. Perrucci

In High Pressure Grinding Rolls (HPGR), the material grinding takes place between the fixed and floating rollers. In this regard, the rollers start to wear over a period of time, which is impacted by for e.g.: ore characteristics, operating pressure, feed material size and non-uniform feed presentation across the roller width. HPGR operational experiences have shown that the rollers do not wear at the same rate. This differential wear rate over time leads to differences in the tangential speeds of the rollers, causing an uneven gap between the fixed and floating rollers in relation to the material. This unwanted but extremely common situation results in a less effective grinding process due to the fact that the slip between rollers is not optimal. As the rollers wear profile increases, the roller with smaller diameter starts to wear further, deteriorating the comminution efficiency up to a point where operators have to stop the HPGR to replace the rollers. Since the wear rate of the rollers is not equal, the replacement of the same cannot be properly planned so that their life-time are fully utilized. In this paper, a dynamic load share control with the use of ABB’s variable speed drive system is proposed, which provides the possibility to the HPGR operator to impact the roller wear in such a way that it equalizes the wear rate to a certain extent and extends the roller life time. Called RollXtend™, this solution includes a load share factor which can be parameterized based on the wear measurement performed manually during maintenance procedure. Additionally, this paper describes an automated load sharing concept based on a non-invasive wear measurement method. The partial results of the technology trial in a copper/gold mine are presented, which aimed at detecting stud damage and estimating the real rollers profile throughout their life time. The final objective of the pilot project was reduce the amount of planned and unplanned downtimes of the HPGR by increasing the rollers life time and avoiding catastrophic stud damages.

Jan 1, 2018

By Vasile Murariu, William Pate, John Herbst, Dilek Alkac

"Multiphysics models are essentially first principles models capable of providing very accurate micro scale predictions. The computational requirements for Multiphysics Models are extensive, precluding their direct use for flowsheet simulations. Population balance models get their form from theory but the model parameters have to be provided from experiments. The prediction errors for the population balance models are typically significantly higher than those for the Multiphysics Models but the computational effort for Population Balance Models is typically much less than that for the Multiphysics models. The hybrid model described here takes advantage of the strengths of each of the two primary model types and minimizing the weaknesses of each. The Multiphysics Model is used to perform high accuracy "experiments" that are difficult or impossible to conduct in laboratories or plants. The results of these experiments are combined with standard laboratory or plant data to parameterize and further enhance the Population Balance portion of the hybrid model. The creation of a useful Hybrid Model is demonstrated for a MP1000 secondary crusher. The validation of the hybrid crusher model is also presented. Finally the use of the Hybrid Model is illustrated in a full comminution flowsheet simulator."

Jan 1, 2014

By T. N. Matveeva, T. A. Ivanova

"The article presents the results of the research aimed at development and testing of new effective reagents – collectors and green modifiers for more complete extraction of gold and platinum to concentrates at reduced loss with waste products. The main deposits of Au and PGM ores of Russia and abroad are presented by refractory raw material with the non-uniform finely-interspersed sulfide mineralization, submicron gold and platinum, the low metal content, non-uniform distribution of valuable minerals. and show low indicators of recovery. The main losses of precious metals (up to 15 %) at flotation are associated with thin slam tailings because of inefficiency of standard reagent modes.In the paper, the new trends in design of collecting agents for extraction of gold and PGM sulfide minerals and their application in flotation tests are substantiated. The original technique for obtaining the modified collector reagents – dithiocarbamate, dithiophoshpinate and dithiazine, incorporated non-ionic compounds that are able to generate stable complexes with gold and platinum has been developed. A novel class of collectors – cloud point polymers showed high flotation recovery of fine particles of gold and platinum. The original technique to create the mineral samples of natural sulfides with ""invisible"" or sub-micron gold on their surface designed helped to indicate the mechanism of selective adsorption of novel agents on Au and Pt-sulfide minerals. Extractive UV spectrophotometry, potential measurements, X-ray phase and spectral analysis, scanning electronic microscopy (SEAM), laser SIM and AFM microscopy were applied to analyze the adsorbed layer of modified reagents on the mineral surface. Selective hydrophobic covering on the surface of micro- and nanoparticles of noble metals provided an increase in their extraction during flotation. New reagent modes of modified collectors and green modifiers were tested in scaled-up laboratory flotation and the results obtained demonstrated the increased quality of the concentrates in terms of gold content by 1.5 times and higher gold recovery by 1.5-5%. The studies have been supported by Grants of the President of RF “Scientific School of Academician Chanturiya” NSh-220.2012.5; NSh-748.2014.5."

Jan 1, 2018

There are interactions between different minerals from the same ore, minerals and grinding media, and the electrochemical conditions present in the system. Grinding in steel rod and ball mills is a common practice in minerals processing. It is accepted, that the electrochemical interactions between the grinding media and minerals in a grinding mill, influence the corrosive wear of balls/rods and the surface properties of the ground minerals. A complex massive sulphide, Cu-Zn, TAKNAR, Iran, was used for all the experiments. The aim of this study was to investigate the effect of grinding media (dry or wet) on the pulp chemistry and recovery of Cu and Zn in bulk concentrate. 1100 g of ore samples were milled, and mill products with d80=85 and 75 micron in wet and dry grinding methods were produced. Rougher bulk flotation experiments were performed with 550g ore samples, at 30% solids. SIPX in conjunction with Aero238 in 1:2 ratio (48 g/t), was used as mixed collector system, and copper sulphate (200g/t) and MIBC (20 g/t) were employed as sphalerite activator and frother. Lime and High purity Oxygen gas were used for adjusting pH at 8.5 and aeration. The results showed that, more positive pulp potentials were measured when the feed had been ground in a dry environment, and the difference in pulp potentials between the dry and wet ground feed was approximately 250 mV after the grinding stage. In dry grinding method, the recovery of Cu and Zn increased approximately 5 and 10%, respectively. In addition, in dry ground samples, the volume of middling and coarse particles (+100 micron) were more and Dry ground flotation feed had better agreed with using a mixture of collectors. After using copper sulphate, pulp potential increased about 50 mV in dry and 75 mV in wet grinding methods. Keywords: grinding media, pulp potential, Cu-Zn massive sulphide, bulk flotation

Sep 1, 2012

By O. A. Punishko, G. G. Mineev, Zabaikalsky Ore-Dressing Plant, M. V. Malova, O. V. Belousova, S. A. Bogidaev

"In order to intensify benefication processes (flotation and magnetic separation) for rebellious tantalitecolumbite ores electrochemical machining of pulp (ECM) is suggested instead of costly mechanic-chemical activation and magnetizing roasting. Any change in the surface mineral-semiconductor potential under the action of electrochemical treatment results in the change in the isoelectrical state of the surface and the adsorption property of the mineral with respect to ionogenic reagents-collectors. In this case conditions are created for regulating the ion composition, reduction-oxidation potential and pH of the liquid phase of the pulp without any extra introduction of expensive and often ecologically harmful chemical substances.Ores containing tantalum and niobium are characterized by complex chemical composition, determining their physical properties (conductivity, dielectric penetration, magnetization value, etc.) and their electric susceptibility.The authors investigations show that the pulp electrochemical treatment leads to the increasing magnetic susceptibility of the paramagnetic minerals. The main chemical elements forming the columbite-tantalite minerals except tantalum and niobium are iron and manganese. They determine the rare-metal minerals paramagnets properties. The electrochemical treatment changes the relation of the oxidized and reduced forms of these elements having. The method of cathode pulp treatment before flotation is successfully tested industrially.In the field of noble metals metallurgy new technological proposals are reduced to the following. As is know, the production of noble metals from unusual raw materials demands the elaboration of principally new technologies new technologies in so far as the methods for gold and silver extraction from ores are as a rule low elective and at the existing level of engineering are economically not expedient.The analysis of the main trends in the field of non-standard raw material treatment shows that the perspective ones are the geo- and biotechnological processes (underground leaching and leaching in heaps - UL and HL and microbiological methods of metal extraction)."

Jan 1, 2003

By Alban Lynch, Benigno Aquino, Hakan Dündar, Alexander Kalugin, Marco Delgado, Alberto Palomino, Ali Türkistanli

Dynamic separators are efficient dry classifiers because new designs during the last 50 years have reduced the by-pass and improved the partition curve. By contrast cyclones have been used as classifiers in wet grinding circuits for 50 years but without serious change and the early problems which were caused by high and variable by-pass, and different mineral specific gravities, still exist. High frequency screens are now used for wet separation and the operating characteristics of closed grinding circuits using cyclones or screens are discussed. Data come from circuits at the Condestable, Cerro Lindo, El Brocal and Catalina Huanca mines in Peru, the Eczacibasi mine in Turkey, and the Apatit mine in central Kola Peninsula in Russia. All classifier data are described by their partition curves and all mill data by their breakage rates. With cyclones the by-pass, d50, and sharpness of the partition curve change as operating conditions change but with high frequency screens the values vary little because the by-pass is low, the sharpness is high, and d50 depends on the aperture size. Data from all plants indicate that lower by-pass and sharper separation improve breakage rates and throughputs. An initial model of the screen is proposed.

Jan 1, 2014

By Heinrich Hutchison, Thomas von Moltke, Roelof F. Sandenbergh, Katarina P. Cerovic

In the leaching of gold in aqueous cyanide solutions the rate of gold leaching may be decreased by the passivation of the gold, that may however be prevented or reversed in the presence of lead species in solution. In the present study potentiostatic, potentiodyanamic and XPS (X-ray photoelectron spectroscopy) analysis were used to further clarify the action of lead ions on the anodic activity of gold in alkaline cyanide solutions. It was found that lead increased the gold dissolution rate as it deposited on the gold surface at potentials more positive than its reversible Nernst potential for bulk metal deposition, i.e. by underpotential deposition mechanism, but that it decreased gold activity if present as bulk plated lead on the gold.

Jan 1, 2003

By Manuel Diaz

"In these difficult times for the mining world, mainly due to the global uncertainty about metal prices and the increased activity of opponents to the mining industry, it is essential that mining companies focus on efforts and strategies that will give them the most flexibility to succeed under the fury of these phenomena. The careful management of systems to control costs, and indicators to measure with great precision actual variations in costs and cash flows, are essential to adequately manage the uncertainty. Similarly, clear corporate and regional strategies designed to maximize cash flow and operating margin will allow the company to be better prepared to face any negative situations caused by declining metals prices, stricter government regulations and increasing social pressure. Gold Fields Limited, a corporation of South African origin and with more than 100 years in the gold mining business, has developed the ability to adapt to large changes generated by different global crisis throughout its history. This occasion will be no different. Given the critical situation of the mining industry in the world today, Gold Fields has embarked on a re-structuring plan at global level that will allow much closer control and real efficiency of production costs. This plan includes the creation of regional business units that allow greater independence for each region while still preserving the standards and cultural values of the Corporation. This presentation will explain why we believe that this approach combines the best aspects of the two styles of business, and what are the expected results. In the Americas Region, Gold Fields currently operates Cerro Corona, in Peru. In addition, the company is considering opportunities for growth in Chile, Brazil, Mexico and Canada."

Jan 1, 2014

By Hamid-Reza Manouchehri, Hassna Aitahmed-Ali, Stellan Sundberg

"In flotation practices as the particle size becomes fine, e.g., p<20µm, the process efficiency declines markedly. When flotation of fine particles is necessary, one method to improve the recovery is selective agglomeration of fines. Different agglomerating methods have been introduced and tested; however, one method which has recently received great attention is to aggregate fine particles by magnetic force. A selective aggregation of the fine paramagnetic particles, e.g., sulfide minerals, can be achieved by applying a high intensity magnetic field during flotation conditioning. The method is simple, selective and effective for fines, and has a low operation cost. However, a minimum magnetic susceptibility of fine grains is required for this process. This method has been demonstrated in different sulfide minerals flotation plants. The implementation of the magnetic conditioning device, ProFlote, in both the Cu-Pb and the Zn circuit of Boliden’s Garpenberg plant in Sweden, where a complex massive sulfide ore is treated, is discussed herein. The preliminary results have shown an increase in the recovery of value minerals, in particular Zn and Ag and considerable reduction in Zn deportment to the final tail. Increases in Cu grade and decreases in Pb grade in Cu-con have been achieved as well."

Jan 1, 2014

By Cristian Melipichun, Leopoldo Gutierrez

The effect of the presence of fine particles of kaolinite and montmorillonite on the induction time for attachment of bubbles to particles of a copper concentrate rich in chalcopyrite was evaluated in this study. The results obtained from induction time measurements were correlated with data of concentrate recovery achieved from micro-flotation experiments. The effect of the presence of fine clays on the stability of air-water foams was also studied through measurements of the foam volume generated in a glass column under different conditions of air flowrate and MIBC concentrations. The experimental results showed that induction time values increased under the presence of fine clays. These data agreed with results obtained from micro-flotation experiments that showed that copper concentrate recovery decreased when clay particles were added. Although a complete explanation for these results is not available, the fact that experimental observations indicated that fine clay particles tend to adsorb on gas bubbles, suggests that the interactions between fine phyllosilicate particles and air bubbles have to be taken into account when studying the effect of clays on froth flotation. Foamability tests showed that the presence of fine clay particles increased the foam volumes only at high additions of clays and low dosages of MIBC. The results obtained at higher dosages of MIBC showed that the foam volumes decreased with the addition of clays under all the experimental conditions tested.

Jan 1, 2014

By Yuexin Han, Wenbo Li, Yan Shan, Yanjun Li, Shumin Zhang

"With the accelerating pace of resource extraction, the quality of resources is decreasing, and the old tailing dams which have served for several decades have become the focus of attention. The secondary recovery of valuable metals in the tailings is an important aspect of the comprehensive utilization of tailings. The average iron content of iron tailing is 8%-12% in China. The research aimed at exploring the low-cost and efficient technical route to recycle eastern tailings of Anshan iron mining area. The purpose of the research is to scientifically find the rational conditions of magnetizing roasting and to provide an increase in recovery and quality of concentrates. The eastern tailings of Anshan mining area belong to high silicon bearing iron tailings, iron mainly exists in form of hematite-limonite with an iron grade of 10.60%, the main component of gangue is SiO2 with a grade of 76.22%. In order to reduce the influence of the tailings on the environment, fluidized magnetizing roasting and low intensity magnetic separation for the eastern tailings of Anshan mining area were carried out to improve the utilization of the tailings. The results indicated that an iron concentrate with an iron grade of 65.30% and a recovery of 85.85% could be obtained under the conditions of gas flow rate 8 m3/h, H2 concentration 50%, fluidized magnetizing roasting temperature at 600? for 20s. Phase analysis, magnetism analysis and XRD analysis on roasted materials indicated that hematite-limonite could be transformed to magnetite during the fluidized roasting, then the effective separation of iron and gangues could be made easily by the weak magnetic separation. INTRODUCTION It is universally acknowledged that the grade of iron ore in China is low, the output rate of iron ore tailings is high, usually more than 60%. At present, the comprehensive utilization rate of iron ore tailings is low in China. Generally, the iron ore tailings are stockpiled in the tailings dam. The tailing dams not only occupy a lot of land, but also takes a lot of money to construct and maintain. In addition, the noxious substances in the tailings, such as residual flotation agents and heavy metals, have a severe impact on the ecological environment. There is little doubt that tailing dams have a visual impact on the environment due to their regular geometric shape. Iron tailings can be treated as compound mineral, which is an important component of comprehensive utilization of mineral resources, and is an has been widely concerned. Lots of scholars have done a large amount of research work on a large number of iron ore tailings. Since the iron mineral crystal grain size is fine and the iron grade is low, the iron tailings have failed to achieve good selection criteria."

Jan 1, 2018

By M. Muravyov, T. Kondrat’eva, A. Bulaev

Metallurgical treatments of sulfide ores containing copper and zinc are characterized by significant losses of base metals, particularly formation of the flotation tailings and slags during the dressing and pyrometallurgical treatment respectively. In addition, SO2 gas obtained during roasting and converting may be as raw material for sulfuric acid production. A treatment of the industrial metallurgical wastes has been investigated. Two samples of old pyrite tailings from two concentrators that contained 0.36% and 0.26% of copper and 0.23% and 0.22% of zinc were leached with 10% sulfuric acid in the column. Recovery of copper reached 47% and 38% while recovery of zinc was 47% and 41% from the first and second samples, respectively. The pregnant leach solutions contained 15.9 g/l and 10.5 g/l of ferric iron. Ferric iron is the strong oxidant and ferric containing pregnant leach solutions can be used for ferric leaching of different types of raw materials containing sulfide minerals. Therefore, ferric leaching of copper converter slag flotation tailings contained 0.53% of copper and 2.77% of zinc with the first pregnant leach solution was conducted. The effect of various experimental parameters on the leaching dynamics of copper, zinc, and iron under batch conditions was investigated. Under the best conditions (temperature 70oC, pulp density 30%) the recovery of copper and zinc reached 80% and 42%, respectively. Thus, it has been shown that acid leaching of base metals from old pyrite flotation tailings with using of the pregnant leach solution for the ferric leaching of copper converter slag flotation tailings is a prospective technique for the complex treatment of mining and metallurgical wastes. Investigated processes could be introduced into the technological flow-sheet of typical pyrometallurgical plants.

Jan 1, 2014

By S. Titkov

At present, Russia is engaged in processing, 3new plants of hard-to-process potash ores with increased content (up to 10 - 12%) of insoluble impurities (insoluble residue ? I.R.). This required additional research to improve the process of potash ores flotation. Based on the study of the effect of dispersive properties of frother and its flow rate on the efficiency of aliphatic amines with different length of the hydrocarbon radical (as sylvite collector) there was showed the possibility to apply high molecular amine with length of hydrocarbon radical C20 ? C26 by normal temperature of circulated plant salt solution (saturated solution KCl ? NaCl ? H2O). There was designed and tested in plant conditions the modified amine collector with the length of the hydrocarbon radical C16 - C26, improving flotation of Sylvite under normal temperature of circulating salt solutions at potash flotation plants. There was made the study of the influence of the hydrocarbon radical length of alkylmorpholine on the Halite flotation from intermediate products of sylvite recleaner flotation with different content of I.R. (silicate-carbonate slimes), at normal and elevated temperature of salt solution. On the basis of the application of modified alkylmorpholine for Halite flotation, there was developed the process of further beneficiation for the intermediate products of sylvite recleaner flotation from potash ores with increased content of insoluble impurities, which can eliminate the circulation of the intermediate products in the process flow sheet of sylvinite ore processing and increase the KCl recovery into the finished product. Keywords: flotation, potash, halite, alkylamine, alkylmorpholine

Sep 1, 2012

By Milind Sabne, Pradip, P Kapur, Beena Rai

"The efficiency of an industrial flotation circuit depends on (a) the selectivity and the kinetics of the reagent combination selected for the separation (b) the hydrodynamic conditions prevailing in the flotation cell (essentially equipment design parameters) affecting both the pulp and froth phase (c) the operating parameters such as feed rate, pulp density, pH, temperature etc. including the mineralogy, particle size distribution and relative proportion of liberated and composite particles of constituent minerals in the feed to flotation circuit and (d) the circuit configuration itself. We have developed a molecular modelling based reagent design and selection framework to assist mineral engineers to arrive at the preferred reagent combination based on a rigorous, scientific and quantitative comparison of various options available for this purpose. Similarly we have also utilized a general circuit design methodology proposed by Kapur and Mehrotra in 1974. The advances thus made in modelling both the reagent chemistry as well as circuit design, along with the availability of sophisticated, automated tools for characterization of ores (liberation as well as mineralogical composition of the different flotation streams) provides a scientifically rigorous, quantitative, robust framework for design and optimization of complex flotation circuits. We illustrate in this paper the power and the utility of our rigorous optimization based approach to designing industrial flotation circuits for the beneficiation of a multi-component feed with the help of few case studies from our own work. With the proposed methodology, higher levels of process efficiencies can be achieved in the industrial flotation plants, in particular those processing complex, multi-component feeds requiring multiple stages of flotation separation. We are currently developing an IT platform consisting of computer-aided decision support tools for arriving at the preferred flotation circuit and the appropriate reagent chemistry for a given ore deposit and/or a given plant."

Jan 1, 2014

By Bo Feng

The development of surface charge of serpentine mineral and implications for sulphide ?otation have been studied through flotation tests, sedimentation tests, zeta potential measurements and optical microscope photos. The results show that the serpentine mineral was positively charged at an extensive pH range, with an isoelectric point (IEP) of 11.9. The magnitude and sign of the pyrite particles were pH dependent and were negative for pH values above 2. At pH value 9, where ?otation of nickel sul?de ores is routinely performed, serpentine and pyrite particles attract through an electrostatic mechanism. Slime coatings of serpentine adhere to the surface of pyrite, reducing pyrite flotation recovery. The removal of magnesium ions from the serpentine surface by acid leaching results in a decrease of serpentine IEP and eliminates the adverse effect of serpentine on pyrite flotation. Therefore, it has been clearly established that the surface charge value developed in the serpentine/aqueous electrical interface is a function of the serpentine surface incongruently dissolution. As a result of hydroxyl dissolution, the magnesium ions are left in serpentine surface, which is responsible for serpentine surface charge. The methods, which can remove magnesium ions from serpentine surface, can be used to eliminate the adverse effect of serpentine on pyrite flotation.

Sep 1, 2012