Search Documents

Traditional mineral processing techniques are more and more difficult to recover the increasingly low grade phosphate ores today. Although bioleaching method has been attempted to process low grade ores in hydrometallurgical field due to economical and environmental reason, it has been hardly used in leaching phosphate ore at home and abroad. Strains of Acidithiobacillus thiooxidans and Acidithiobacillus ferrooxidans were collected and separated from the acid drainage of a coal mine in Anhui province of China. Ultraviolet irradiation and Microwave inducement were applied to the bacterial cultivation process to produce strains of Acidithiobacillus thiooxidans and Acidithi-obacillus ferrooxidans able to tolerate extremely low pH conditions and generate sulphuric acid by oxidizing elemental sulfur or sulphide and the mutagenesis can achieve higher leaching rate. The bioleaching result will improve more by the addition of Tween series surfactants.

Jan 1, 2014

By J. Faitli

The Lake Balaton is the biggest and for many reasons the most important lake in Hungary. To preserve its healthy nature it is necessary to remove the accumulated mud time to time, similarly to the many living waters, lakes and rivers everywhere. Typical existing technologies (mechanical, hydraulic) require large depositional areas, where the removed slurry and mud is dewatered through very long time. One problem is the non existence of an economical mud thickening technology. Another major problem is that current methods remove the sand fraction with the mud as well. Many times sand has to be complemented from outer sources to endanger the natural balance of the living water. By the financial support of the NKFP 3A/068/2004 Hungarian Research Project our consortium has been looking for the solution to the above mentioned problems. The original ideas of the project were: 1. Sand should be separated and returned to the water by hydrocyclon; 2. New mud thickener should be developed based on the principle that vibrating rods can force settling and packing of mud particles. The work was started by fundamental research with different samples from Lake Balaton and River Bodrog. An automated settling column (45L) has been built for the investigation of the effect of vibrating rods on the settling behavior of suspensions. An optical sensor has been developed by with the settling curve (height of settling slurry as function of time) can be automatically measured. Different vibrating methods and parameters have been tested by the application of a linear motor and mechanical eccentric drive. On the basis of the fundamental research a new thickener, called the rod ? lamella thickener has been developed and an industrial size (50m3/h) mud removing technology has been built. Main parts of the technology are the traditional dredging barge and the thickening technology. The thickening and sand separation technology is tugged by the dredging ship. Its main elements are the homogenization tank, slurry pump, hydrocyclon and the rod ? lamella thickener. In this unit lamellas carry out pre-thickening, then vibrating rods further increase the concentration. The thickened mud is transported out by a screw - of which revolution number is precisely controlled - against a spring supported valve. Paper reports about the design, building, water probe and on-site tests of this mud removing technology. Two new patents had been presented, one is about the rod ? lamella thickener and the other is about the mud removing technology with sand separation.

Jan 1, 2014

By Y. X. Yang

Bottom ash is a solid waste stream in a Waste-to-Energy (WTE) processing plant during the combustion of the municipal solid waste (MSW). In the Netherlands, bottom ash contains typically about 18% metals originated from the MSW, and current industrial practice could recover about 10% metals through magnetic and eddy current separators. The remaining 8% as the finer particles is difficult to recover through current physical separation technology. Among various alternatives, vitrification is one of the promising options to immobilize the ash and recover the remaining metals. During vitrification a homogeneous glassy slag and a Fe-Cu based alloy were obtained. In the cur-rent study, the metal alloy recovered from the bottom ash originated from a Dutch Waste-to-Energy plant contains about 82 wt% Fe, 12 wt% Cu and 6 wt% other alloying elements and impurities such as C, S, P, Ni etc. The generated alloy does not have direct commercial applications, and separation of copper from iron-based alloy is critical to obtain the market value of both copper and ferrous constituents. To find a suitable processing route of this metal alloy, various alternative approaches have been considered for an efficient removal of copper from the alloy, and the focus in the present study was on the sulphide treatment at elevated temperatures of 1400 ~ 1500oC. The tested sulphide systems include pure FeS, FeS containing sulphide mixture (such as Na2S and Al2S3), pyrite (FeS2) mineral, ZnS containing sludge as an industrial waste. It was found that the carbon saturation of the alloy is proved to be an essential condition for a proper phase separation. The results showed that FeS mixed with Na2S, ZnS containing sludge and pyrite are effective sulphide systems for copper removal with a removal efficiency of 92% by using pyrite and 95% by zinc sludge at a S/Cu ratio of around 7 times of the stoichiometry. The copper content drops from 12 wt% to about 2 wt%. However, it is still difficult to remove copper completely from the alloy in a single step, and a multi-step operation is needed. The present research is expected to contribute both to the utilization of the metal recovered from bottom ash, and to the general recycling of steel scrap where copper removal from the steel scrap is a critical issue.

Jan 1, 2014

By Nóra Schreithofer, Kari Heiskanen

"INTRODUCTIONThe knowledge of the adhesion forces between particles and bubbles is of key importance in the improvement of flotation models. The development of the Colloidal Interaction Force Measurement Apparatus (CIFMA) opened the possibility to quantify the adhesion forces between particles and bubbles. The aim of this study was to examine the effect of three main variables: the approach velocity, the loading force and the loading time on the adhesion force between an air bubble and a hydrophobized silica particle."

Jan 1, 2003

By N. Pradhan

In the Sukinda valley, Orissa, India, a large quantity of overburden material is generated during the mining of chromite mineral (on average 10 tons for every ton of ore). The overburden hereby depicted as ?lateritic nickel ore? contains on an average 0.5% Ni. IMMT Bhubaneswar is working on this material for extraction of nickel and cobalt. But for better recovery of metal values, thermal activation or thermal reduction of ore is required. An alternative biotechnological route for reduction of ore is hereby attempted. An anaerobic dissimilatory Iron (III) reducing bacterial consortium (here denoted as IRB), capable of imparting iron phase changes in the lateritic nickel ore was established which improves the subsequent extraction of co-precipitated Co (III) and Ni (II) from the ore. In this study, properties of thermally and microbially reduced lateritic nickel ore are compared vis-à-vis original ore. Due to the phase changes, original light brown color of the lateritic nickel ore changes to dark brown on IRB treatment. This dissimilatory reduction of ore leads to formation of some magnetic particles, which were separable by hand held magnet. Roasting and IRB treated ore on acid leaching with H2SO4 show about 45 % and 36 % leaching of nickel ore compared to about 18 % leaching from the original lateritic ore. If bacterial reduction method is successful, cost intensive method of ore roasting process can be eliminated. Thus, it is possible to make use of dissimilatory iron reducing bacteria for recovery of valuable metals from off grade iron ore/ laterites. Keywords: lateritic nickel ore, bacterial reduction, thermal reduction, dissimilatory fe (iii) reducing bacteria

Sep 1, 2012

By Takashi Furuyama, Sukeyuki Mori, Abel Bissombolo

"In flotation practice, a good recovery of minerals largely depends on the degree to which the valuable minerals have been liberated from the associated gangue during the grinding process. Therefore, a regular measurement of the degree of liberation can provide data for the assessment of the quality of separation and predicts the effect of changes in the grinding-classifying circuit on flotation process. Generally, the standard procedure for measuring the degree of liberation requires the preparation of polished sections - a time consuming operation that also has the disadvantage of providing an overestimated number of free particles because of the stereological nature of produced samples.The present work is an alternative approach to avoid these miscalculations and establish a system of control for fluorite flotation plants. The system deals no only with the state of liberation but also the dynamic behavior of individuals particles and mineral components within the grinding-classifying and flotation circuits. It involves methods such as sieving, x-ray diffraction analysis, study of polished sections and microscopic counting of preliminarily sieved minerals particles from a fluorite processing plant, randomly dispersed on a glass slide, but not embedded in a resin mounting medium. If a complete information on the textural properties of minerals in the ore (including its mineral components distribution) can be obtained through x-ray diffraction analysis and study of polished sections, the microscopic counting is used to determinate with enough accuracy the mineral liberation, estimate the grade of fluorite ore and products, determinate the deportment and approximate recovery of individuals particles and mineral components within the investigated circuit. For a count of 100-1000 particles in each n-size range, the counting method was found to be a particularly reliable and less time consuming operation that could substitute the chemical analysis of fluorite ore for an estimate of the grade:"

Jan 1, 2003

By Silvia França, Hudson Couto

"In this paper, an alternative beneficiation process was developed to recover nickel minerals from low-grade weathered ores. The studied sample, 0.3% Ni grade, is essentially composed of nickel sulfides (pyrrhotite and pentlandite); magnetite and silicates (mostly talc and amphibolites) are the primary gangue minerals. The particle size distribution was controlled using a grinding operation to avoid producing an excess of fine particles by overgrinding. The sample underwent a grinding step for the fine degree of liberation. The slimes (-20 ?m) were removed via two desliming stages in hydrocyclones (diameters of 1.5" and 2"); the ground material, which was classified in a range of (-150+20) ?m, was processed by column flotation in three different stages: rougher flotation for magnesium silicates, rougher flotation for sulfides, and cleaner flotation for sulfides, using pilot flotation columns (2" and 6" in diameter and 20 ft high). The goal of using the preliminary magnesium silicate flotation step was to remove hydrophobic minerals (mostly talc) that would float naturally with the sulfides, which would decrease the Ni grade in the concentrate, as well as to reduce the MgO content because this compound is considered harmful in metallurgical processes when a grade greater than 9% is used. The final concentrate obtained in the cleaner flotation step reached up to 2% Ni and 7.0% MgO. The global and flotation recoveries in the process were approximately 30% and 60%, respectively, due to the losses of Ni during the desliming process. Despite this low global recovery, the adopted beneficiation process can be considered an interesting alternative to produce nickel concentrate from tailings or waste materials."

Jan 1, 2014

By Kari Moen, John Rasmus Leinum, Jarle Hjelen, Terje Malvik

"Automatic identification and characterisation of mineral raw materials and beneficiated products are of major importance in mineral processing. However, minerals show great variety in their composition and physical and chemical properties. Industrial minerals may contain the same elements in about the same amount. In these cases backscatter electron imaging or chemical analysis are not sufficient to identify the minerals. Another problem arises when micro textures are not detectable in traditional imaging or the grain size is smaller than the X-ray spatial resolution.As a supplementary technique in these cases, application of crystallographic information by electron backscatter diffraction (EBSD) in the scanning electron microscope (SEM) may be a suitable method. By means of EBSD, diagnostic mineral information can be achieved if indexible patterns are provided.Until now EBSD has not been used frequently on geological samples for mineral and micro structure discrimination.The technique has been demonstrated on three Norwegian mineral raw materials and one Italian marble and shows that it has some advantages compared to traditional techniques."

Jan 1, 2003

By G. V. Kalabin

"The paper supports applicability of satellite imagery at regional and local level for rapid quantitative assessment of natural environment in zones of activity of mining complex enterprises. Exacerbation of environmental problems during mineral mining and processing associated with their scale and geography of field distribution through the vast territory of our country requires constant monitoring of natural environment status, which necessitates engagement of space surveillance nowadays. It is proposed to use the monitoring of land cover and land use at regional and local level for the environmental assessment of a particular production or complex productions. You must establish the dependence of NDVI change trend with the magnitude of anthropogenic impact on the source or multiple sources of environmental pollution a particular area.. We present the results of studies of vegetation remote sensing methods in a number of territories placing mining enterprises. INTRODUCTION Ensuring a healthy environment is necessary both in untouched areas and disturbed. The condition of the developed territories should be monitored with particular attention, since the restoration of the disturbed territories requires great efforts and financial costs. More narrowly, the health of the environment (Zakharov V.M. and etc.,2001) means its quality ensuring the health of man and other species of living organisms, which includes two aspects (Zakharov V.M. and etc, 2000): - ensuring an environment conducive to human health as a biological species: - maintaining the health of the natural environment, i.e. its constituent species of living organisms and plants. The consequence is the disturbance of natural ecosystems, which determines the quality of the environment, favorable for human habitation and the state of health of the population in total determine the status of the territories where enterprises for the development of georesources are located and allow them to be ranked according to the degree of environmental danger. Without knowledge of the trajectory of ecosystem successions, it is impossible to offer adequate requirements for the technologies used to ensure the implementation of the preserved natural potential after the removal or reduction of man-made stress."

Jan 1, 2018

By G. W. Zhang

Ultra-fine Stirred Mill is a kind of high energy efficient equipment for ultra-fine grinding, and has been the mainstream equipment in the submicron powder and slurry industry. This paper mainly describes flow-field numerical simulation of the three popular ultra-fine grinding mills: (respective-ly as) Disc Stirred Mill, Pin Stirred Mill and Spiral Stirred Mill, by means of the software Computational Fluid Dynamics (CFD). In the flow-field numerical simulation, the velocity gradient, shear rate dispersion of the flow-field, the viscosity dissipation rate were analyzed with CFD. It is discovered that Pin Stirred Mill has the highest velocity gradient in circular directions and the most homogeneous distribution of shear rate among the three. Flow-field numerical simulation provides a new way (and means to) for the parameter optimization design and project enlargement of Ultra-fine Stirred Mill. The experiments were also carried out, the results are consistent with the results of the simulation analysis. For example, in GCC grinding experiments under the same conditions, the specific energy consumption of Pin Stirred Mill with 3600L in volume is 15%~17% less, and its processing capability is 13%~15% better than Disc Stirred Mill. Now with its optimized structure and excellent performances, more than ten sets Pin Stirred Mill with 3600L in volume have been used in industrial production in Shandong, Guangdong and Hunan province.

Jan 1, 2014

As the high-grade copper deposits in the world become depleted, there is an increasing focus on developing lower-grade ores which contain problematic impurities such as arsenic. Indeed, many high-arsenic ore bodies remain undeveloped because of their high arsenic levels. Separation of arsenic from copper at the beneficiation stage is difficult using the current processing techniques and invariably copper concentrates produced from these ores contain high arsenic levels, sometimes so high as to make them unacceptable to copper smelters. New, sustainable approaches are needed to allow development of high-arsenic copper ores while at the same time minimizing arsenic dispersion into the biosphere. The most promising route for separating arsenic from copper at the flotation stage centers on the use of pulp potential control. In recent years CSIRO has demonstrated at laboratory scale, for a number of high-arsenic copper ores, that crude flotation separation between arsenic-bearing minerals and copper-bearing minerals can be made. The differences in specific minerals responses to changes in pulp potential and pulp pH are exploited for this separation. Such separations nominally produce a low-arsenic high-copper concentrate and a low-copper high-arsenic concentrate. The former can be smelted without penalty, while the latter requires further treatment to capture and stabilize the arsenic and to recover the residual copper. Consideration has now been given to treatment options for the high-arsenic low-copper product. A pyrometallurgical option, involving a low temperature roast to selectively fume off the arsenic and leave a high-copper calcine, coupled with an arsenic stabilization step, has been demonstrated in the laboratory, and a preliminary techno-economic evaluation shows the process to be economically favorable. These results were recently published. CSIRO has now investigated an alternate hydrometallurgical option, involving atmospheric alkaline sulphide leaching of the high-arsenic product, where the arsenic is selectively dissolved leaving a copper-rich leach residue. The leaching testwork was carried at on the same high-arsenic low-copper material used in the roasting studies, enabling a techno-economic comparison of the alternate roasting and leaching treatment options to be made. The alkaline leaching work is briefly described and the results of the process option comparison presented and discussed. Keywords: arsenic, copper, economics, enargite, ore flotation, tennantite INTRODUCTION

Sep 1, 2012

By F. A. V. Guimarães, A. M. Costa

"The moisture in sintering is a very important parameter for the performance of the process. It allows that the granulation takes pace in an efficient way making the water bridges between the bigger particles used as nucleus and the finer particles that perform the coating of those coarse particles. The formation of the micro pellets is extremely important to prevent loss in permeability of the bed in the sintering grate, avoiding excessive fuel consumption and producing a quality sinter. The aim of this project is to use some of the methodologies for determine the saturation degree on ores and coal to determine the optimal moisture for sintering. In the sinter pot grate series, 3 to 4 assays in a series of 10 are required to determine the optimal moisture for the process. The saturation degree curve test has shown that is really viable to use this technique to skip those tests and go directly to the series to determine productivity and the coke / anthracite consumption. In an industrial scale can be used to adjust the water addition in the conventional mixing methods used in the sintering plants to increase productivity in the process.INTRODUCTION Sintering Sintering is a high temperature agglomeration process in which iron ore fines are partially melted and bonded together using fluxes and a source of fuel, usually coke breeze. The agglomerated product, sinter, has improved metallurgical properties making it an ideal ferrous burden that enable the passage of hot gases in the iron-making blast furnace. The sintering process is normally carried out over three basic stages: granulation, ignition/sintering, and product sizing. In the granulation stage, iron ore fines (usually a blend of selected ores), sinter return fines, fluxes and fuel, and are mixed with water and micro-pelletised in a drum or disc before being introduced in the main granulation circuit. (Wang, Teng, & Wang, 2017)."

Jan 1, 2018

By J. Temuujin

Mongolia has some of the world?s largest coal reserves with an estimated total coal reserve of over 150 billion tonnes. At present, over 90% of Mongolian electricity is produced by combined heat and thermal power stations. The main coal deposits used for Central power system's power stations are Baganuur, Shivee-ovoo lignite type coal and Shariin gol bituminous coal. In Mongolia almost 600,000 tonnes of coal combustion by-products are disposed of in waste ponds. In this research, we have thoroughly characterized Mongolian coal combustion by-products including fly ashes sourced directly from thermal power stations and ash retrieved from ponds. It was determined that fly ashes generated from Baganuur and Shivee-ovoo coal deposits are class C, while ash from Shariin gol coal is class F (according the ASTM C618). All ash products were characterized by chemical, mineralogical, granulometrical, porosity, FE-SEM and radiation methods. Fly ashes sourced directly from power stations were found to be more suitable for manufacture of geopolymers for building materials application and zeolite synthesis than ashes retrieved from ash ponds. The adsorption and porous properties of zeolitic compounds were measured and found to be suitable for adsorption of Cr6+ from simulated tannery waste water. Keywords: coal, coal combustion by products, synthesis, geopolymers, zeolitic compound

Sep 1, 2012

Spent automobile catalyst is an important secondary resource of PGMs (platinum group metals) and the recovery is significant. Various methods of recovery technology have been reported and applied in practical production, including pyro- and hydrometallurgical processes. Since the grade of PGMs in the catalysts is so low, approximately 0.5 wt. %, the present recycling technologies require high energy-consumption, it is of great significance to enrich the PGMs with some energy saving physical separation methods as a pretreatment. Automobile catalyst is usually composed of cordierite phase as a substrate and alumina phase, with PGMs, which covers the cordierite phase. We adopted the quenching pretreatment, one method of thermal shock, to generate micro-cracks between the two phases and separate the alumina phase from cordierite. Quenching was carried out by heating the catalysts in an electric furnace of different temperatures followed by rapid soaking into cold water. It was found that the phase boundary between alumina and cordierite was broken in the quenching and selective separation (detachment) of alumina from the cordierite could be achieved in the following surface grinding. The effect of quenching was checked by microscopic observation, hardness measurement, and chemical analysis. This paper figures out the stress formula of the quenching process, which is largely connected with layer thickness and temperature gradient by using an FEM (Finite Element Method) simulation and clarifies the mechanism of crack generation in the quenching process. Keywords: automobile catalyst, PGM, quenching process, FEM

Sep 1, 2012

By N. Acarkan

Beneficiation of the pyrite concentrate of the Kastomonu-Küre (Northern Turkey) copper ore seems to be attractive due to its high Cu, Co, and Zn contents. Pyrite concentrate were used in the experimental studies. Cu, Co, and Zn were recovered from the concentrate by the sulphatizing roasting, leaching and the precipitation using H2S. Sulphatizing roasting experiments were carried out in a rotary furnace and the optimal roasting conditions were found to be at 650°C roasting temperature and 3.0 h roasting period and addition of Na2SO4 of 3 % for the concentrate containing 0.58% Cu, 0.22% Co, and 0.04% Zn. Then, the roasted product was repeatedly leached with 10 g/L H2SO4 solution. Optimal conditions were found to be 60 oC leaching temperature, 2 h leaching period, and 30% pulp density. Leaching efficiencies for Cu and Co were over 99 %. The valuable metals in the pregnant solution were selectively precipitated by H2S as sulfides. Selective precipitation of Cu, Zn, Co was achieved by adjusting the pH and the temperature of the leach solution. Final metal recoveries of 99.20% Cu, 99.40% Co, and 95.60% Zn were attained. The precipitated sulphides are marketable products. Roasting gases with their 15% SO2 content are suitable for the production of H2SO4 and the leach residues can be integrated with the iron ore processing plant as they contain 57.50 % Fe, 17.70% gangue (SiO2, CaO, etc.), 0.04% S, and 0.06% non-ferrous metals.

Jan 1, 2014

By Hans-Åke Häggblad, Bertil I. Pålsson, Jan Stener, Kent Tano, Andreas Berggren, Pär Jonsén

Numerical modelling of grinding in tumbling mills is traditionally done with the discrete element method (DEM). The grinding balls are then represented by DEM particles and the mill structure is considered rigid. To include more physical phenomena several numerical methods can be combined. One important improvement is to include the mill structure response, using the finite element method (FEM). The interaction between charge and lining can then be studied in detail. The pulp can also be included using a particle-based continuum method e.g. smoothed particle method (SPH). The strength of SPH lies in modelling of free surface flows and very large deformations and it is suited to model simultaneous fluid and granular flow. Still, the coarse particles (grinding balls) in the charge are suitable to be model using DEM. Each of these methods has their strength and weaknesses, but combined they can successfully mimic the main features of the charge movement. With these numerical tools the complex interaction between the different components of the grinding process; pulp, charge, lining and the mechanical behaviour of the mill, can be studied together. This work will present novel numerical approaches to model, simulate and validate charge behaviour in tumbling mills. These numerical models give possibilities to better understand the physical and mechanical behaviour of particulate material systems during grinding in a tumbling mill. This is important in order to develop and optimise future high-capacity grinding circuits and save energy.

Jan 1, 2014

By B. P. Baruah

A good deposit of high sulphur coals of tertiary origin is existent in North eastern region of India. These coals are known to have indifferent characteristics in comparison to other Indian coals. The general Physico-chemical characteristics are low ash and high volatile matter, calorific value and sulphur content. Sulphur in these coals (70-95% of organic) is mostly affixed to the structure of the coal. Owing to the stringent environmental regulations, the utilization of these coals has severe limitations due to high sulphur content. In the present investigation, sulphur incorporation in to these coals has been discussed along with possible organic sulphur functionalities. The various desulphurization techniques carried out for removing sulphur from these coals have been discussed. Two step oxidative desulphurization processes has been found to be most efficient for organic sulphur removal along with mineral matter and potential toxic elements. Keywords: oxidative desulfurization, potential toxic elements, sulfur incorporation

Sep 1, 2012

By B. Aydin, G. Erturk, G. Bulut

Coal is a complex material because of its structure consisting of carbon constituents and mineral matter. Flotation is readily carried out due to hydrophobic characteristic of coal. Therefore coal flotation is the most commonly used technique for fine coal beneficiation in order to acquire clean coal separating ash forming mineral matter from carbonaceous matter. In the coal flotation, floatability of coal both depends on characteristic of coal and used flotation reagent. Frothers as a flotation reagent are used to facilitate air dispersion into fine bubbles by prevention of bubble coalescence in the pulp phase, and stabilization of flotation froths. In this study, the effects of frother types and concentrations at different pH and particle size on the coal flotation were investigated. The representative sample was taken from Zonguldak, Turkey. It contains 9.1% ash and 7313 (kcal/kg) calorific value. Pine oil, Dowfroth 250, MIBC and Isooctanol were tested as frother types. It is determined that 1.92 ppm frother concentration is sufficient to float coal, except pine oil. In mixed frother tests, it is seen that Dowfroth 250 is more effective than others. No significant difference in coal recovery was observed for flotation tests at the different pH values. The best results are obtained in size of coal (-0.1 mm) with all frothers.

Jan 1, 2014

By Moris Fresko, Julia Sun, Charles C. Golembewski, Vytas Svalbonas

"A history of mill strain gaging at Metso is presented. The output of these strain-gaging programs is compared with calculated stress ranges from different finite element solutions. These comparisons expose the amount of approximation that exists in the analytical solutions, starting from geometry, and material properties, and ending with different forms of internal load models. The influence of strain gaging results on mill design and analysis practices is also discussed. While these instrumentation programs are valuable in identifying areas of high stress in mills, and locations of stress concentration factors, they are by no means extensive or comprehensive enough to verify general internal load models. The vast majority of the programs were aimed at getting additional data about potential failure points, rather than describing overall mill stress behavior. This is especially true since the more recent gaging programs have not included the difficult task of gaging the mill rotating structure interior. This paper tries to avoid the novice path of leaping to general conclusions on the basis of insufficient data."

Jan 1, 2014

By Z. M. Dai

Microorganisms in AMD (Acid Mine Drainage) were enriched in 9K culture medium. The enrichment was applied to leach copper pyrite after the microbial community structure and metabolism was stable. Before and after bioleaching, the microbial DNA was extracted and applied to RFLP (restricted fragment length polymorphism) analysis to demonstrate the relationship between the leaching efficiency and the change of microbial community. Atomic absorption spectrometry results showed that when concentration of the pulp was 10% and pH were 1.5, 2.0 and 2.5, the leaching rate were 56%, 57% and 34% on the 18th day respectively. These results indicated that the rise of pH resulted in the decrease of leaching rate. In lower pH condition, the growth of microbe was faster: when pH was 1.5, the microbial cell number reached to 1.4×107cells/mL on the 9th day; while pH was 2.5, the microbial cell number decreased to 4×106cells/mL. The analysis of microbial community structure showed that Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans were dominant species before bioleaching (account for 43% and 32% respectively). And after bioleaching, these two species were still dominant when the initial bioleaching pH were1.5 and 2.0. While the initial bioleaching pH was 2.5, the proportion of these two species decreased. These results demonstrated that the initial bioleaching pH would affect the microbial community structure in bioleaching system at room temperature, and this affect could lead to different copper pyrites bioleaching efficiency.

Jan 1, 2014