Search Documents

The flotation of nickel sulphide minerals is normally difficult in the presence of serpentine minerals due to the coating of serpentine particles on the nickel mineral surface. To improve the flotation, dispersants such as polyphosphate and carboxy methyl cellulose are normally used to remove the slime coating. However, in the flotation using high ionic strength process water, these dispersants are invalid due to their ionic nature. In this study, a new type of non-ionic dispersants, Pluronic triblock copolymers were examined with an objective of improving the flotation of ultrafine pentlandite (a nickel sulphide mineral) in the presence of lizardite (a serpentine mineral) in saline water. Three Pluronic triblock copolymers varying in solubility and hydrophile-lipophile balance (HLB) values were studied by flotation tests, settling tests and froth measurement. It was found that two of the copolymers improved pentlandite flotation against lizardite, and one copolymer deteriorated the flotation. The effect of Pluronic triblock copolymers on the flotation was actually linked to their dispersibility and foamability, which were governed by their physical properties. The two copolymers with a higher solubility or HLB value produced more stable mineral suspensions and more stable froth in the flotation resulting in better nickel grade and recovery in both rougher and cleaner flotation. Keywords: ultrafine particle, flotation, slime coating, dispersion, saline water, triblock copolymers

Sep 1, 2012

By Ana Elisa Casas Botero

The Rhodococcus opacus microorganism was evaluated as a biocollector for flotation of barite. The electrophoretic behaviour of the mineral, before and after R. opacus interaction, was evaluated and showed that the cells adhesion shifted the mineral zeta potential curves. Adhesion tests were suggested a high affinity of the bacteria for barite. The experiments of the adsorption rate of the R. opacus on the mineral surface showed fast kinetics, achieving a maxim of cell adsorption after 5 minutes. Adsorption isotherm curves for barite could be categorized as Langmurian (L) type II. The best bioflotability results for barite achieved values around 75% for a R. opacus concentration of a R. opacus concentration of 250 ppm in the pH around 5.0. The studies were compared with the flotation of barite using a traditional collector. The bioflotation experiments were discussed considering the obtained adhesion tests. The results were supported by the Thermodynamic approach for selected pH values. The fundamental flotation studies showed the paramount potential that R. opacus presents as a biocollector and its possible application in the mineral flotation industry.

Jan 1, 2014

By Jens Markowski

The EU Directive 2000/53/EC on end-of life vehicles (ELVs) states that in 2015 at least 85 wt.-% of a vehicle has to be reused or recycled. This result in the obligatory need to separate additionally metallic and other components of the automotive shredder residues (ASR), so that they can be professionally prepared for recycling and reuse further. Currently the iron-containing fines of ASR are deposited as it is not possible to process in blast furnaces due to its particle size (< 4 mm), composition and material properties. Additionally problems are also caused in handling and transportation (dust) of the material. This work focuses mainly on the ASR materials utilization in blast furnaces. Material was further separated into two consecutive fractions by carrying out repeated crushing and magnetic separation twice. The two fractions have significantly higher iron content (up to 75 wt.-%) compared to the initial material mixture. The materials were assessed for their usage in blast furnaces based on the possible pelletisation with and without binders, stability of pellets, shape and size of pellets, etc. Pelletisation of the material was carried out with a single mould pellet press. Further lignite coal was added to the mixture as additive which improved the pelletisation behavior and the mechanical stability of pellets. Lignite coal was chosen as a reducing agent in the blast furnace process contributing towards additional savings in energy supplied. The experiments reveal that the production of pellets from iron-containing fines is possible with a lignite coal admixture of about 15 wt.-%. These pellets displayed good mechanical stability and can be used in blast furnace processes in recovery of the recyclable metals which are currently not recycled. The recycling of not yet recyclable metals would reduce the deposition and can be easily adopted into the economic cycle by their utilization. Keywords: Automotive shredder residue (ASR), FE-fines, pelletisation

Sep 1, 2012

By M. Roy

Coke combustion during sintering process is significantly governed by coke breeze size distribution, which in turn affect sinter quality i.e. sinter granulometry, Tumbler index, Reduction Degradation Index and Reducibility Index of sinter. To know the effect of microfines of coke breeze on sintering process parameters, pot sintering tests were conducted and it was found that when microfines are eliminated and optimum coke size (1-3mm) is used yield of sinter increased by more than 7%. Similarly productivity increased by 9%, the strength of sinter i.e. ISO Tumbler Index increased by 2.3% and +10mm sinter size increased by 5.5%. Controlling of microfines during crushing and by improving crushing index will result in improved quality and productivity of sinter with lesser amount of coke breeze. This paper describes that how to optimize solid fuel i.e. coke breeze consumption in sintering process through granulometry control. Keywords: iron ore sintering, coke breeze granulometry, productivity of sinter, quality of sinter

Sep 1, 2012

By J. B. Yianatos

A practical an interactive model to describe the operation of a flotation bank of mechanical cells was developed based on the hydrodynamic and metallurgical characterization of large industrial flotation cells. Thus, the mineral grade and recovery, as well as the stream properties along the flotation bank can be described in terms of the operating variables. The model was built considering the flotation bank as a distributed system, so the solution for the water and solids mass balances, per size classes, for each single cell, are sequentially solved. Also, each cell was described by two distinct zones, the collection zone characterized by the flotation rate constant and the froth zone characterized by the froth recovery. The mineral feed was described in terms of the mineral species and particle size classes, using a rectangular flotation rate constant distribution. Also, the effect of changing the actual operating variables (air flowrate, pulp level, pulp density, pulp flowrate, etc.) on the mineral collection process, in the collection (pulp) zone, was considered downstream along the bank. The froth recovery of floatable mineral has been estimated by measuring the mass flowrate of particles entering the froth by true flotation together with the concentrate mass flowrate (ton/h). The mass flowrate of collected particles at the pulp/froth interface level was calculated from direct measurement of bubble load (ton/m3) and gas flowrate (m3/h). Flotation recovery is mainly related to the froth depth and air flowrate. All parameters considered in the model have been adjusted from direct measurements in plant site. Also, the effects of other operating variables such as reagents dosage, top of froth grade, or froth discharge velocity are presently under study. This procedure has been tested using data from industrial rougher operations consisting of flotation banks with 5 cells to 9 cells in series, and different cell sizes, such as 45m3, 130m3, 160m3 and 250m3. Thus, it has been shown that the model approach is a powerful tool for flotation cells diagnosis, operation and development of new control strategies, as well as, to evaluate the effect that de-sign and operating variables have upon the collection and froth zones performance in large flotation cells.

Jan 1, 2014

By Boris Albijanic, Hongjuan Chen, Bogale Tadesse

"During mechanical flotation of fine liberation sized complex rare earth ores, a large fraction of ultrafine valuable mineral particles are lost to tailings. Fine gangue mineral particles can be entrapped within the froth phase and be floated together with target mineral particles. Another common challenge in ultrafine rare earth mineral flotation is the formation of a sticky froth (excessively stable froth). Thus, the improvement of the flotation of fine and ultrafine rare earth bearing minerals through appropriate cell design and reagent selection is highly desirable. The aim of this study is to investigate the performance of a pico-bubble cavitation flotation column in improving selective recovery of ultrafine rare-earth elements (REEs) bearing minerals from complex and low-grade ores. In pico-bubble cavitation column, very small bubbles are generated which are capable of attaching to ultrafine particles and consequently modifying their surface properties. The overall effect of these processes should lead to improved flotation selectivity and recovery of ultrafine RE mineral particles. In this paper, the effects of a number of flotation operating variables on recovery and grade of REE minerals was investigated using a continuous pilot scale pico-bubble column flotation. At the flotation conditions used in this study, subtle monazite upgrade was observed while gangue Fe oxide was preferentially floated even in the presence of depressants. INTRODUCTION Rare earth elements (REEs) have unique properties such as superconductivity and catalytic activity, and are in high demand for a large number of cutting-edge technologies in the modern world including the production of mobile phones, fuel cells, displays, permanent magnets for wind power generation, high-capacity batteries, green energy devices, etc (Naumov, 2008). REEs tend to be intimately associated within many minerals, and are rarely found in high concentrations in deposits for economic extraction. Up to now, among over 250 minerals containing REEs, bastnasite (Ce), monazite (Ce, Th and La) and xenotime (Y) are the three main minerals that contain sufficient grade of REEs for commercial exploitation (Zhang and Edwards, 2012). The deposits that contain bastnäsite, monazite and xenotime usually have complicated mineral compositions, with various valuable minerals of fine embedded grain sizes in association with complex gangue minerals. In order to ensure liberation of the REEs minerals, fine grinding to less than 30 µm is necessary. This fine grinding leads to difficulty in recovering a large proportion of fine and ultrafine particles in separation processes such as flotation (Trahar and Warren, 1976). Consequently, highly liberated and ultrafine fine valuable REEs particles are lost into tailings during traditional mechanical flotation. Besides, the formation of extremely sticky and stable froth inhibits the drainage of hydrophobic particles. Thus, improving flotation of rare earth bearing minerals, particularly the ultrafine size range, is highly desirable."

Jan 1, 2018

By Paulo Castillo, Cesar Gomez, Jaime Alvarez

Operations using flotation to produce mineral concentrates require testing of frothers to characterize their ability to preserve bubble formation size and to build a stable froth. Many techniques have been proposed to measure parameters associated with these two roles. These techniques focus, in general, on only one of these roles and are based on special equipment operated at conditions quite different from those existing in industrial cells and columns. Both roles have been simultaneously characterized in a laboratory flotation column, but the requirements associated with the installation and operation of one of these units, are a serious limitation for its use on-site. A technique based on the use of a laboratory mechanical cell, a common piece of equipment in operations, will have wider application. Establishing the ability of a frother to control coalescence by preserving bubble formation size is done through bubble size measurements as a function of frother concentration. Froth build-up and stabilization is associated with the amount of water carried by bubbles into the froth layer, which has been demonstrated to correlate with the gas holdup in the collection zone. Procedures devised for determining the critical coalescence concentration (CCC) from measurements of bubble size as a function of frother concentration, and the gas holdup by collection of water displaced from the cell by the presence of bubbles at different frother concentrations, were tested. Three analytical-grade frothers were utilized: a straight-chain (1-heptanol) and a branched (MIBC) alcohol and a polyglycol (PPG425). The results obtained at a standard set of conditions, demonstrated consistent differences between these frothers, and the ranking from least to most effective for reducing bubble size or decreasing water drainage followed the same sequences found when more complex frother characterization techniques are used.

Jan 1, 2014

By V. F. Petrov

Cyanide is widely used gold lixiviant for hydrometallurgical processes. The resulting tails contain complex toxic compounds. With reference to this, the protection of the environment should be the major issue. A complete detoxification of cyanides before disposal, a partial detoxification to the allowable concentrations and a disposal of tails at a polygon followed by the detoxification of excess water into the environment are offered as an environmentally friendly way of disposal. However, a complete detoxification of the cyanidation tails does not give the required results due to the presence of toxic compounds, cyanides and thiocyanates in tailings ponds. This is due to adsorption-desorption process occurring between solid and liquid phases. A partial detoxification is used to down cyanide to the allowable concentrations, which are safe to the environment. The storage of tails without detoxification is mainly used at low concentrations of toxic compounds in the disposed tails. With reference to this, water recycling is practiced by Russian plants in order to reduce as much as possible or almost eliminate toxic effluents into the environment. Fresh water is applied if necessary and to make up for water losses, with 8-12% of total water supply. This allows for the stability of water balance and the decrease of consumption of the reagents applied. The conditioning technologies of water recycling followed by regeneration of free cyanide and metals recovery as saleable concentrates are specially developed due to adverse impact of water recycling on gold recovery processes due to high concentration of base metals (copper). These technologies are also profitable. In order to detoxify cyanide in the tails for tailings dam, effective and inexpensive technologies involving a seasonal use of detoxified reagents were developed. For example, a technology with aldehydes use which is applied by a series of operations. Effluents disposed to the environment are detoxified using chlorination followed by almost a complete destruction of toxic cyanides and thiocyanates. Before disposal, chlorinated water is settled to precipitate the resulting hydroxides of metals and complete chemical reactions such as a full decomposition of hypochlorite ions. In order to protect ground water, watertight screens from local water-resistant materials are used. The samples of these materials were previously tested and chosen according to their maximum ability to adsorb toxic compounds in the tailings pond. If local water-resistant materials are not available, whole welded impermeable polymer screens are used. The options mentioned allow the storage of cyanidation tails in accordance with national ecological standards. Keywords: cyaninides, thiocyanates, wastes, environmental safety, recycled water-supply, detoxification, storage

Sep 1, 2012

By G. G. Dong

This paper presents BF flotation machines in brief which are manufactured by Beijing General Research Institute of Mining & Metallurgy (BGRIMM). Dimensional analysis and similarity criteria have been used to scale up BF flotation machines. These scale-up criteria can be used to determine mechanical structure and hydrodynamic parameters including mixing, solids suspension, air transfer and power and so on. Similarity criteria are used to design 40m3 flotation machine being based on data from 1.2 m3 to 20 m3 flotation machines. Hydrodynamic tests of 40 m3 flotation machine in water are discussed.

Jan 1, 2014

By C. Hazotte, M. -O. Simonnot, V. Houzelot, B. Laubie, M. Guilpain, B. Jally

"More than 400 plants in the world are able to accumulate nickel (Ni) in their aerial parts at concentrations higher than 10 g per kg of dry biomass. Then, Ni can be recovered from the biomass of these hyperaccumulator plants. Agromining is a chain consisting in growing such plants and producing metal. It has been developed thanks to the combined know-how of agronomy and hydrometallurgy. Hydrometallurgical processes have been designed; two different pathways were developed: i) acid leaching of ashes after biomass combustion and ii) direct Ni water extraction after biomass grinding. Experiments with 2 species of Ni hyperaccumulators (A. murale from the Balkans and R. bengalensis from Malaysia) have shown that the first process is very robust and transposable. For the second one, the way Ni is stored in the plant has a strong influence on extraction. A. murale transformation was explored in more details from the lab scale to the pilot scale. Results proved that Ni is totally transferred into the aqueous phase after 2 hours at 90 °C. A life cycle assessment has clearly shown the environmental interest of this approach (especially by detoxifying agricultural soils). INTRODUCTION Agromining is an emerging phytotechnology aiming at recovering metals thanks to hyperaccumulating plants (van der Ent et al., 2018). These plants are able to accumulate very high concentrations of metal in their aerial parts. For example, for nickel, the hyperaccumulation threshold is 0.1%, i.e. 10 grams of metal per kilogram of dry biomass. There are some advantages to use this technology instead of conventional mining techniques: •,Treating unconventional metal resources: they can be (i) natural soils with low concentrations but also low fertility because of the metal presence (like serpentine soils for Ni) (Bani et al., 2015), (ii) mine tailings or (iii) industrial wastes (like surface treatment sludge) after soil construction (Rue, 2017);"

Jan 1, 2018

By W. Y. Liu

A sulfate reducing bacteria strain (named SRB-A) is isolated from sanitary wastewater by using anaerobic technology of Hungate. The studies of physiological, biochemical and phylogenic of the isolated strain are carried out. The colonies of the strain are circle. Cells that are slightly curve, rod-shaped with the size of 1.0~3.0µm in length and 0.8~1.0µm in width. The optimum temperature for growth of the organism is 30~35°C. The optimum pH for growth is 7.0~7.2. Strain SRB-A can use sodium lactate, sodium citrate, sodium acetate, ethanol and acetone as electronic acceptor but can not use glycerol, glucose, sucrose and sodium oxatate. The isolated strain reduces sulfate, sulfide, sulfur, DSMO and FeCl3, then nitrate and nitrite can not be used. The strain has higher tolerance of NaCl, and the optimum growth occurs in the presence of 5%~8% (w/v) NaCl. The result of 16S rDNA sequence analysis indicates that the isolated strain SRB-A is the most similar to Desulfo-vibrio halophilus, and the level of the similarity was 98.4%. The isolated strain has a stronger ability to reduce sulfate, and the level of sulfate reduction reaches about 90% at pH 7 in the liquid medium. 0.6 to 0.8 is the optimum COD/SO42- in the medium for the isolated strain to show better ability to reduce sulfate. At pH 2.5 the level of removal of Cu2+ reaches 96.3%. Under the condition of pH 3.5, the level of removal of Zn2+ reaches 92.6%. When the value of pH reaches about 7, the Fe3+ is precipitated by the formation of Fe(OH)3, and Fe3+ is removed up to 89.4% at last.

Jan 1, 2014

By Sudhir Srivastava

India hosts a wide range of globally significant mineral resources, including four fuel minerals; 11 metallic minerals; 22 minor minerals and 52 non-metallic minerals. The country ranks among world?s top five nations for its commodity reserves of coal and iron ore. Interestingly, only small part of country&apos;s landmass has been explored that provides opportunity for future substantial mineral discoveries. India plans to double infrastructure investments to US$ 1trillion. Despite the challenges in infrastructure project implementation, mining sector remains a key driver of demand growth for commodities in the years to come with a good prospect to grow in future.

Sep 1, 2012

By Valery V. Kostjuk, Victor. N. Bredikhin, Alexander I. Shevelev, Evgeny A. Kazban

"The investigations to improve the process data have been done in order to stabilize the functioning of drying units. The scheme of turnings preparation with centrifuging and subsequent thermal degreasing (tandem) is proposed. To improve the efficiency of the process the scheme of reclamation of the centrifuge fugate is developed with production of oil and service circulating water. Empirical dependences of the turnings temperature influence on the lubricant-coolants content in centrifuging are gained. When the turnings temperature is increased to 80 C the residual content of LC is decreased by 1.5%. The investigations aimed to improve the preparation of non-ferrous turnings have allowed to decrease the melting loss by 15-20%; to stabilize the process of thermal drying of turnings; to decrease sharply (by 60- 70%) the volume of LC combustion products; to reclaim the centrifuge fugate and produce oil and servicecirculating water.Non-ferrous turning and primarily aluminum and copper alloys turning is a stable source of secondary raw materials for metallurgical works.Direct by lubricant-coolants (LC) of various types: synthetic, semi synthetic, oily and emulsions.On the base of investigations concerning various methods of the non-ferrous turning processing the favorable one has been selected taking in to consideration the economy, ecology and quality of the finished product (alloy). Two-stage process is developed. The main idea of the process is the elimination of the lubricant-coolants (LC) to the limit specified in advance. The applied method is centrifuging with subsequent final elimination of LC by thermal method.Constant value of LC content at the inlet of the thermal unit excludes practically the oxidation of metal and as a consequence increases the output by 10 –15 % in metallurgical processing."

Jan 1, 2003

By H. R. Manouchehri

"In all electrical beneficiation methods, the difference in electro-physical properties of the contributed mineral particles, essentially frictional charge, electrical conductivity and dielectric constant properties are exploited to achieve separation. The composition of the raw material determines what kind of either corona charging, conductive induction, or triboelectric separation method should be employed. The process is versatile and is influenced by different parameters related to mineral characteristics, surrounding ambient conditions and electrical and mechanical attributions of the separating device. Electrical separation is surface based beneficiation method which is mainly affected by the surface and surface changes of the minerals. Therefore, it is essential to understand how the electrophysical properties of the minerals can be changed/modified. During electrical/electrostatic separation process, both charge magnitude and its polarity that developed on the particles and therefore, their electrical beneficiation potential is essentially defined by surface phenomena. Therefore, it is essential to understand how the main electro-physical parameters can be changed/modified with applied surface treatment/pretreatment methods to promote separation. Surface treatment of minerals is carried out by different means, including chemical conditioning, irradiation, thermal treatment, etc. This paper discusses and analyze the electrical separation process, electrophysical properties of the minerals with special focus on the effect of surface pretreatment/treatment methods to affect electrical beneficiation potential of the minerals. The surface treatment methods vary in a wide range from simple surface cleaning to more complicated chemical conditioning and doping. The knowledge of the solid-state physics and chemistry leads to improve the beneficiation potential of different mineral systems by choosing suitable treatment method(s). Despite the complexity and multiplicity of the charging mechanisms, difficulties in separating fines it seems to be beneficial make our attempts to further investigate and develop the process as dry, low cost beneficiation process, especially nowadays when environmental concerns, as well as energy and water consumptions are main concerns for mining industry."

Jan 1, 2018

By S. J. Lui

Sodium oleate was an effective diaspore collector, whereas chelate collector OL2 showed certain collecting power over diaspore and nonionic surfactant OL3 showed little collecting ability. Then experiments were carried out using sodium oleate as the main collector with the addition of OL2,OL3 to study the influences on diaspore flotation, it could be seen from the experiments that accelerants had a marked influence on the recovery of diaspore, which could be raised by 10%, and the addition sequence also affected the flotation behavior: the best results could be gained when the accelerants were mixed thoroughly before adding and the best ratio of collector OL1 and accelerant OL2, OL3 stood at 30:2:1. Based on the calculation of the ingredients in the sodium oleate solution, sodium oleate reacted with surface of the mineral and formed the acid-soap polymer [HOl?Ol-] when pH was about 9. Zeta potential test showed the accelerant promoted the absorption of collector on the mineral surface, which lowered zeta potential. As could be seen from surface tension experi-ments, the addition of accelerant OL3 lowered the CMC value of OL1 solution, which was equiva-lent to raise the power of the agents. Further Infrared Ray experiments showed the co-absorption of OL1 and OL2 make aluminum oleate on the mineral surface more stable. Up till now, the mixed reagents with sodium oleate as the main collector, combined with other two accelerants had been used in the Zhongzhou concentration plant, which is the first diaspore flotation plant in China.

Jan 1, 2014

By M. Guo

Coal-based Direct Reduction in Interior-combustion Shaft Kiln (CDR/ISK) is a brand-new technique. Compared with the traditional Coal-based Direct Reduction (CDR) technique, its main character is to use Interior-combustion Shaft Kiln (ISK) as the reactor of direct reduction. After being crushed and grinded, iron ore is made into green pellet, which will be surface-coated by coal fines. Then, the surface-coated green pellet can be directly reduced in ISK. The pellet should not be too dry and should be charged from the top of ISK. Oxygen-contained air should be blasted into ISK to keep the temperature in it higher than 1000 degrees centigrade, at which iron oxide will start direct reduction. The reduced pellet will be discharged from the bottom of ISK and after de-surface-coated, spherical Direct Reduced Iron (DRI) can be gained. The volume of carbon monoxide in the off-gas discharged from ISK is less than one per cent. By using this technique to get one tonne DRI, the consumption of coal is about 300kg of fixed carbon, which is much lower than the energy consumption by using other CDR techniques. There is a lot of complex refractory iron ore in China, which remains unexploited. The iron-bearing minerals in this kind of the iron ore can not be beneficiated economically by present technique of gravity, magnetic, flotation or magnetic roasting because the iron minerals are too very finely disseminated to be liberated, or, the iron minerals are too similar to gangue to be separated each other. By using CDR/ISK, complex refractory iron ore can be directly reduced in lower temperature and all kinds of iron mineral can be turned into iron metal. As the grains of iron metal growing larger during direct reduction, magnetic separation can be used to separate iron metal from gangue mineral, thus high-grade iron metal fines can be gained. According to the experiments, the grade of iron metal fines is above 90 percent and the recovery of iron is higher than 90 percent. The consumption of coal to process one tonne of complex refractory iron ore is only about 90kg of fixed carbon.

Jan 1, 2014

By Weiran Zuo, Narayan Krishnan, Frédéric von der Weid, Emmy Manlapig, Fengnian Shi, Klaas van der Wielen

Laboratory study has identified a new application of high voltage electrical pulse technology for pre-weakening ores. In recent years, the Julius Kruttschnitt Mineral Research Centre (JKMRC), Newcrest Mining and SELFRAG AG have conducted joint research in validation of pre-weakening of SAG mill feed through the pilot scale tests and comminution circuit simulations. Ten tons of SAG mill feed with a top particle size 150 mm were tested with two pilot scale SELFRAG machines installed in Switzerland. A simulation study using JKSimMet software was carried out to find where the high voltage pulses pre-weakening technique can be best applied in a gold-copper ore comminution circuit, based on the data of the pilot scale SELFRAG tests. A novel comminution circuit was designed, which incorporated SELFRAG to pre-condition part of SAG mill feed (9.5 to 150 mm) and to treat the circulating SAG mill pebbles. The high voltage pulse technology effectively reduced the amount of ‘critical size’ particles in the SAG mill and pre-weakened particle strength for grinding. Attributing to the nature of bi-modal size distribution and the significantly reduced F80, the simulations showed that the SAG mill had spare capacity to process part of hydrocyclone underflow from the secondary ball mill grinding circuit. The simulations indicated that the novel comminution circuit had the potential to remove two MP1000 pebble crushers and one 10 MW ball mill from the existing 2000 t/h grinding circuit. A 5 kWh/t energy reduction by adopting the novel comminution circuit in a gold-copper operation may be realized. This would result in substantial savings in operation costs.

Jan 1, 2014

By Daniela Campos, Aldo Casali, Gonzalo Montes-Atenas

The understanding of the effect of the major variables influencing the froth flotation performance may allow both to predict and to identify best operating conditions towards optimizing the process efficiency. The aim of this research work is to model the effect of dissolved oxygen onto froth flotation performance. Experimental pilot plant results were obtained from a continuous circuit consisting of a ball mill and a rougher bank of four flotation cells. A series of flotation experiments were run with different conditions of dissolved oxygen keeping constant most of other operating conditions. Variables difficult to control were measured or estimated. A set of mathematical models suggested in the published literature were tested. It was found that the copper recovery results were highly sensitive to the concentration of dissolved oxygen. The latter confirmed the reactions mechanisms associated to the collecting capabilities of current flotation reagents used in the flotation of copper sulfide ores. On the contrary, the results of molybdenum recovery varied non-linearly with changes in dissolved oxygen which could not be explained directly in terms of the computed specific rate constants. The error analysis confirmed that Klimpel continuous model exhibited the best specific rate constant correlation with molybdenum recovery data. Lastly, the classic particle force balance equations indicated that the adjustments of estimated mineral liberation with experimental data exhibited a turning point when passing from highly liberated to low liberated particles. The values of recovery for such turning point correlated well with the concentration of dissolved oxygen. The results indicated corrections due to changes in the dissolved oxygen must be incorporated in future froth flotation descriptions.

Jan 1, 2014

By Sunil K. Tripathy

Particle characteristics such as size, density, liberation and magnetic susceptibility play vital role in magnetic separation technique. To understand the performance of magnetic separation process for chromite beneficiation industry, particle characteristics need to be analysed. However, to date, this has been an expensive and time consuming task, thus only minimal amounts of this type of data are available in the literature. Several new methods are being developed, that will produce the required mineralogical and liberation data to provide processing information rapidly and inexpensively. Among these, QEMSCAN is a unique and advanced characterisation equipment used for liberation analysis for different ore whereas S.G. Franz Isodynamic Separator for determining the magnetic susceptibility. In Indian chromite deposits, the content of iron bearing minerals in the ore is typical which controls the Cr:Fe ratio in the product while treating in gravity based beneficiation plant. In the present investigation, detailed characterisation of two distinct chromite ore samples from Sukinda chromite deposit, India, was investigated which includes advanced mineral characterisation using QEMSCANand magnetic susceptibility measurement by using Frantz Isodynamic separator, etc.. Presence of haematite and gibbsite along with chromite mineral were identified as major gangue minerals in the high grade ore from XRD pattern whereas Goethite, Quartz, Haematite, Kaolinite, Ringwoodite identified in the low grade ore. The mass magnetic susceptibility of low grade ore is very high 5.2 cm3/g compared to 2.7 cm3/g for high grade ore, due to the presence of abundant quantity of iron bearing minerals. Subsequently, these two types of ore were subjected for magnetic separation for improving Cr:Fe ratio by using different magnetic separators viz. induced roll magnetic separator, wet high intensity magnetic separator, rare earth roll magnetic separator, rare earth drum magnetic separator. The results of magnetic separation studies indicated that, Cr: Fe ratio of the chromite ores can be improved to 3.99 and 1.97 from the feed assaying 3.09 and 1.29 respectively. Studies on rare earth roll magnetic separator indicated that both the ores were upgraded to a maximum Cr:Fe ratio level at optimised condition. Keywords: characterization, QEMSCAN, magnetic separation, rare earth roll magnetic separator, industrial mineral, chromite

Sep 1, 2012

By S. C. Borah

Graphite, a mineral form of pure carbon, is one of the most versatile minerals in industry, because of its varying physical properties and characteristics. The mineral occurs naturally in the form of tubular crystals or microcrystalline earthy lumps, or it is disseminated in rocks, which have undergone intense metamorphism. India has a large deposition of graphite minerals out of which about 43% are found in Arunachal Pradesh. However, compared to the rest of the country, the North-East Region and particularly Arunachal Pradesh has not attracted attention till date for detail investigation for characterization, beneficiation, prospecting and/or exploitation of the mineral resources including graphite. Bulk graphite sample were collected from upper Subanshiri district of Arunachal Pradesh. Chemical analysis of the representative samples were carried out and found that 7.29%, 19.60% and 6.07% of fixed carbon (FC) is present in graphite sample collected from La-Lamdak, Bopi and Taliha, Arunachal Pradesh, respectively. Chemical analysis of the ash of the graphite sample shows presence of impurities such as silica, Al2O3, Fe2O3, Ca, Mg etc in the graphite sample which are also supported by XRD and SEM-EDX investigation. The graphite samples of Arunachal Pradesh are low grade and do not fulfill the market requirement for the industrial applications. Therefore, low-grade graphite is subjected to beneficiation for the upgradation of the graphite for industrial applications. We have adopted the dispersion?cum-settling technique for the beneficiation of the graphite sample collected from Arunachal Pradesh. The FC of 40.21% with 41.17% raw graphite recovery which is equivalent to 71.02% carbon recovery have been obtained by gravity separation technique using only distilled water without any chemical reagent in case of graphite sample collected from Bopi, Arunachal Pradesh. The graphite sample is upgraded up to 47.75% FC with 41.91% raw graphite recovery, which is equivalent to 85.85% carbon recovery with the pH adjustment at 9 with NaOH. Keywords: graphite, beneficiation, gravity separation, arunachal Pradesh

Sep 1, 2012