Search Documents

The relative abundance of coal in India compared to other fossil fuels makes it a natural choice as the primary source of fuel, be it for steel making, power generation or for other uses. The wide variations in nature and type of Indian coals formed during lower Gondawana period and categorized as difficult-to-wash due to its typical mineral matter association with the organic matrix call for suitable beneficiation techniques as the preferred option for quality upgradation. The good quality coking coals of the upper seams are fast depleting leaving behind the inferior quality lower seam coal. The lower seam coals presently being mined are mostly low volatile coking coal (LVC). They constitute about 50% of the total coking coal reserves in India. The beneficiation of Low Volatile Coking coals pose a major challenge and detailed R & D studies was taken up to study the beneficiation characteristics of these coals. The studies revealed that the liberation characteristics at coarser sizes are very poor and the coal is to be ground to finer sizes for liberation. The most important factor that determines coal cleaning efficiency is liberation of organic matter from mineral matter. To achieve liberation grinding is necessary as a result range amount of ultra fines (-0.063 mm) coal is generated. Presence of these large amount of ultrafine in the coal fines, often impose severe technical constraints affecting not only its floatability but also in the downstream treatment of the products like dewatering and cake formation particularly when it is beneficiating through froth flotation. In the present paper optimization of ultra fines (-0.063 mm) has been tried for a LVC coal of Jharia coal field for the better liberation and beneficiation of the above coal fines. It is observed that by optimized, combination of size and number of balls generation of fines can be controlled with liberation. Keywords: coking coal, liberation, floatability, dewatering

Sep 1, 2012

By Rajamani R. K.

The design of tumbling mills has progressed from the Bond work index concept of the 1950s to the population balance concept of the 1980s and then made a quantum leap forward with the discrete element method in the 1990s. The failure of a SAG mill at the Grasberg mine site set in motion the inquiry into the role of shell lifter geometry on the profile of the charge motion within the mill. Quickly, it became evident that this could only be accomplished by tracking individual motion of ore particles and grinding balls and not by study of en masse motion of the charge that had been established previously. The discrete element method (DEM) which was prevalent in the civil engineering literature at that time proved suitable to tackle this simulation problem. In 1991, the two dimensional simulation of laboratory scale mills was validated with the DEM. Later this simulation method evolved into ?MillSoft?? a simulation software package for the design of lifters in ball and SAG mills. MillSoft?simulations proved that cataracting charge motion is not conducive to the life of lifters. The old rule of thumb that the number of shell lifter rows should equal twice the diameter of mill in feet was shattered by simulation results. Instead, the number of rows equal to the diameter of the mill in feet, providing that the lead angle of lifter is around 25 degrees, was established as being more optimal. This bold design change was first implemented and tested by Mark Sherman at Alumbrera Mines in Argentina. Two 36-ft SAG mills responded extremely positively to the design change. This success was immediately repeated at Collahuasi, Pelambres and other mines in South America. The design change has so far exceeded expectation that there is not a single SAG mill around the world today that does not employ a relief angle on its shell lifter. The DEM method has advanced in the hands of the author, mining companies and universities, notably in Australia and South Africa. Today, three-dimensional simulation of charge profile and slurry transport is a standard in the design of mills. There is strong pursuit of a virtual comminution machine with DEM in Australia. In South Africa, an experimental method known as positron emission tracking is emerging as a method for tracking particles in grinding mills. The computational burden of computing with millions of particles in three-dimensional simulations has been eased to less than a day with a technique known as GPU computing. Keywords: DEM method, GPU computing, SAG mill, tumbling mill simulation, discrete element method

Sep 1, 2012

By J. A. Venter

Mineralogical studies indicate the Pt-Pd-Bi-Te class to react poorly on the flotation stimuli and indications are that these minerals are slow floaters. However, recent studies performed on a number of minerals from this class indicated strong interactions with potassium ethyl xanthate resulting in the formation of dixanthogen (only one of several xanthate species). The poor flotation response is not a result of poor interaction of xanthate with the surface. It is proposed that the oxidation products of sulfides in the process water interact with the PGM surface. To test this, the effect of thiosulfate (an important oxidation product of sulfides) was investigated by employing electrochemical measurements and FTIR spectroscopy. The electrochemical investigations indicate no strong effect of thiosulfate on the interaction of xanthate with the minerals surface as well as the reduction of oxygenthiosulfate is likely not responsible for the poor flotation response of these minerals in industrial plants.

Jan 1, 2014

By Sumantra Bhattacharya

The per capita energy consumption in India is 510kgoe/year, the global average being nearly 1818kgoe/year. Correspondingly low is the per capita CO2 emission at 1.25t against the world average of 4.39t.65-70%, at times more, of India?s power generation from about 190,000 MW installed capacity, is however coal fired.India therefore has to secure diversified sources of energy and solar power is increasingly being looked as the real alternative to the existing over dependence on coal. To ensure sustainable solar power it is essential to secure its raw material base that is ?silica?, hitherto considered as ?minor minerals?. That calls for immediately addressing the issues of land availability, solar power cost, developing a dynamic inventory of silica containing minerals, appropriate processing technology and strong regulatory framework for sustainable mining and processing of all silica rich minerals. Keywords: silica, silicon, Thar, power generation, India, quartz, solar power

Sep 1, 2012

By Mohsen Hashemzadehfini

Nowadays heap leaching has become established as a mineral processing technology for treatment of some low grade minerals such as copper, gold, and zinc, etc. Heap height, particle size, leach reagent consumption, and metal recovery are four important metallurgical parameters in a hydrometallurgical process like heap leaching. This paper investigated the effects of heap height and particle size on copper recovery as well as acid consumption. Three heap heights of 2, 4 and 6 meters and two particle size fractions of less than 25.4 mm and 50.8 mm were selected as variables in the experiments. The research results showed the inverse relation between heap height and copper recovery as well as acid consumption. Under given conditions, the copper recoveries of minus 25.4 mm ore are 78.63%, 66.27% and 52.88% higher than that of minus 50.8 mm samples for the heap heights of 2, 4, and 6 m, respectively. Both copper recovery and acid consumption increase with decreasing particle size. Keywords: heap leaching, heap height, particle size, acid consumption

Sep 1, 2012

By Kumar Ranjan, Kumari A. V. Asha, G. E. Sreedhar, Banerjee R. Raja, M. Narasimha, R. Shivakumar

In this paper, numerical simulation of magnetite, medium segregation and coal partitioning have been made in a 350 mm diameter cyclone. An attempt is made to assess the nature of impairment in efficiency in relation to the increasing amount of near gravity materials in coal. The CFD model approaches the Algebraic Mixture (ASM) model with the granular option and Reynolds stress model (RSM) to resolve the air core and turbulent mixing of the medium and coal particles. The partition characteristics of the DMC were modelled using both Lagrangian & Eulerian particle tracking for particles ranging in size from 0.5 to 8 mm and in density from 1200 to 2000 kg.m-3. Lagrangian frame work based Discrete Phase model used to simulate the coal particle trajectories inside the DMC and attempted to understand the residence time of different size and density coal particles. It was observed that coal particles having density near to separation-density (having fifty percent of probability to under flow and overflow) are exhibiting increased residence time than any density particles. As expected the smaller size coal particles shows higher residence time than the coarse coal particles. CFD simulations on effect of NGM mass fraction are simulated and analyzed using ASM model including for coal and magnetite. Coal particles with high NGM content show significant effect in misplacement of coal particles towards wrong products at all relative densities. The residence time of the particles increases because of its increased interaction with near dense particles. The effect of NGM fraction on overall cyclone performance as well as detailed flow assessment in terms of residence time distribution, NGM particle concentration profiles with respect to LZVV is presented.

Jan 1, 2018

By L. C. Zhou

The floatability of andalusite and associated minerals are studied and their action mechanisms of andalusite and associated minerals with collector alkyl benzene sulphonate are also studied. Through the mensuration of electrical potential and the infrared spectroscopy, as well as desorption tests, it is confirmed that the interaction of andalusite with sodium dodecyl benzene sulphonate (SDBS), is in addition to physical adsorption, but also is chemical adsorption. The study results of the pure minerals are used for the flotation of actual andalusite mineral. By flotation from contain-ing 45.68% andalusite ore, the fine andalusite concentrate is gained which Andalusite grade is 85.88%, containing Al2O355.29% and Fe2O3 less than 1.5%.

Jan 1, 2014

By E. V. Zelinskaya, V. U. Starostina

"The Irkutsk region is a raw material region. There are a lot of big enterprises for extraction and processing of oil, gas, coal, iron, gold and rock salt. Besides of it, refractory clays, limestone, mica, gypsum and talc are mined in the region. The most important type of mineral raw material is a gold. More than 8.5% of the total mining in the Russian Federation is extracted in Irkutsk region. It is about 0.7% of the world production. The environmental problems of mining and processing enterprises are a complex set of issues that requires of the searching of effective methods to be solved. One of the key environmental problems remains the reduction of waste generation and the introduction of environmentally safe waste management. After analysing different methods of environmental impact assessment it is established that the method of Life Cycle Assessment is one of the most effective methods for mining production. This method base? on the material balance of flows of raw materials, products and waste. The method of Life Cycle Assessment allows to identify the effects of environmental pollution under the influence of mining and processing at a quantitative level and to show real quantitative forecasts of the possibility of managing the flows of raw materials and waste.INTRODUCTION The Irkutsk region is a raw material region. There are a lot of big enterprises for extraction and processing of oil, gas, coal, iron, gold and rock salt. Besides of it, refractory clays, limestone, mica, gypsum and talc are mined in the region. The most important type of mineral raw material is a gold. More than 8.5% of the total mining in the Russian Federation is extracted in Irkutsk region. It is about 0.7% of the world production. The main provider of precious metal is the Bodaibo region. This is a main location for the major ore companies such as “Vysochaishy”, which produces about 5.0 tons a gold per year; “Pervenets”(PJSC Polyus, the largest gold producer in Russia) - 4.5 tons/year, “Druza” - 0, 5 tons/year. Placer gold is extracted by more than 40 enterprises. In connection with this, there are many plans about a building of new and reconstruction of concentrating factories. Consequently, an increase in the volume of processing is expected. The main projects are the construction of a new mill of the Mining and processing plant GOK “Vysochaishy” with a capacity of 2.6 million tonnes of ore per year; the development of the “Uhakhan” gold-field - 23 km from the “Goltsa Vysochaishy” gold-field; the opening in the Bodaibo region the next parts of the gold-deposit ""Pervenets"". Additional, the growth in a gold production can be achieved by a store of gold in the “Sukhoi Log” deposi"

Jan 1, 2018

By G. P. Karmakar, K. K. Chandan

"The drilling mud is an essential part of the drilling process, which plays a major role in keeping safe and efficient oil and gas well drilling. In the oil industry, bentonite clay dissolved in water produces the simplest type of drilling muds. Bentonite clay contains montmorillonite particles. These particles are dispersed uniformly in water and such dispersions are used in various industrial products like paints, ceramics, pesticides and drilling muds. The bentonite clay easily dissolves in water and increases the viscosity of the water, which is one of the most important properties of a drilling mud. Bentonite has the highest swelling capacity, which is responsible for building up of the viscosity of the clay-water system. The flocculation behavior of bentonite is one of the major concerns for the performance of the water-based drilling mud in the oil and gas well drilling process. The behavior of drilling mud greatly depends upon the quality and quantity of bentonite clay, as well as the additives that are used in their formulations. In this work, a comprehensive study has been carried out to find out the effect of added polyacrylamide (PAM) polymer, surfactant, pH and salt concentrations on the dispersion/ flocculation characteristics of bentonite clay-water system. It has been observed that the increase in PAM dosage reduces the residual turbidity and improves the settling rate of the bentonite particles. The flocculation rate has also been found to be better under higher pH conditions. The combined effect of salt concentration and PAM dosage improved the overall flocculation efficiency of the system.INTRODUCTIONIn the oil industry, bentonite clay dissolved in water produces simplest type of drilling muds. Bentonite clay containes montmorillonite particles. These particles are dispersed uniformly in water. Such dispersions are used in various industrial products like paints, ceramics, pesticides and drilling muds (Akther et al., 2007). The bentonite clay easily hydrates in water and increases the viscosity of the mud system (Razi et al., 2013; Meng et al., 2012). Bentonite clay in the drilling mud increases the viscosity which is one of the most important prop erties of a drilling mud. Bentonite has the highest swelling capacity, which is responsible for the building up viscosity of the clay-water system (Sonmez et al., 2013). The drilling mud is an essential part of the drilling process, which plays a major role in keeping a safe and efficient oil or gas well drilling (ASME, S. S. C., 2005). The flocculation behavior of bentonite is one of the major concerns for the performance of the water-based drilling mud in the oil or gas well drilling process. This behavior of drilling muds greatly depend upon the quality and quantity of bentonite clay, as well as the additives that are used in their formulations (Yu and Amanullah, 2005; Akther et al., 2007). Bentonite particles form aggregate under certain conditions including high temperature, and high concentration (Luckham and Rossi, 1999). If the quality of bentonite is not sufficient to accomplish intended viscosity of the muds, it is essential to add certain additives to increase the viscosity and prevent aggregation of the system (Razi et al., 2013). The anionic polymer bearing sample can build up inter-particle bonds between the polymer and clay particles. The addition of various additives like, polymers control the dispersion and enhance the viscosity of the mud by controlling the flocculation of montmorillonite particles in bentonite dispersion (Heller and Keren, 2002; Mahto and Sharma, 2004)."

Jan 1, 2018

By I. Zh. Bunin, G. K. Khachatryan, N. E. Anashkina

For optimization of diamond processing technology the influence of nanosecond high voltage pulses on mechanical and technological properties of diamond crystals and kimberlite rock-forming minerals (calcite, olivine, serpentine) was investigated. Using methods of Fourier Transform Infrared Spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), microscopy and mikrohardness measurement the changes of structural, physic-chemical surface properties, and microhardness of minerals as the result of impacts, was studied. Non-thermal impacts caused a decrease of kimberlite rock-forming minerals microhardness in general to 40-66% as the result of surface microstructure destruction which is caused by formation of micro cracks, traces of surface breakdown and other defects. At the same time, the pulse energy impact on natural diamonds led to formation of B2 type crystal lattice microsift defects, elevated concentration of which increases the hardness properties of crystals. The obtained result indicates possibility of applying pulsed energy effects to improve the softening efficiency of diamond-bearing kimberlites rock-forming minerals without damaging the diamond crystals and ensuring their preservation by the subsequent grinding of ores. By IR and X-ray photoelectron spectroscopy revealed that processing by hight voltage pulses causes a change of natural and synthetic diamonds surface functional cover composition. Short-term exposure (~ 10 - 30) leads to detachment and partial destruction of secondary phases mineral films on the surface of natural technical diamonds, increasing floatability and hydrophobicity of crystals. However, with increasing duration of treatment (~ 30 - 150) occurs surface hydroxylation (found by XPS for synthetic diamonds), as a result of diamond surface layer oxidation. The effect of increasing the natural diamonds flotation activity by 14% (from 47% to 61%) was experimentally established as a result of processing diamond crystals with nanosecond pulses (~ 10-50 sec), which indicates the principal possibility of using pulsed energy impacts to intensify the diamond flotation during processing diamond-bearing kimberlites.

Jan 1, 2018

By Barun Gorain, Aparup Chattopadhyay

"Many double refractory gold deposits are characterized by the dominance of ""invisible gold"" (sub-microscopic gold) as solid solution or as colloidal-sized particles in different sulfides and other phases. These deposits are mainly composed of silicates and carbonates with moderate clay and mica content and with minor amount of sulfides and organic carbonaceous matters. The presence of highly preg-robbing and finely disseminated carbonaceous matter adversely affects gold recovery in leach circuits. Characterization of carbonaceous matters, commonly known as TCM and quantification of gold associated within these carbonaceous matters along with different sulfide and oxide phases is highly complex and challenging. Studies were initiated on various complex ore deposits and also on samples representing various process streams. This paper presents the development of a systematic approach to gold deportment studies using state-of-the-art mineralogy characterization techniques for quantification of invisible and visible metal contents in various species. The relevance of this mineralogy characterization to metallurgy will also be discussed in this paper."

Jan 1, 2014

By R. B. Shu

A moderate thermophilic microorganisms, has been isolated (45?) from a typical sulphide mine in the region of Mo Jiang located in the southwest of China. The culture has been used to extract copper from chalcopyrite concentrates obtained from De Xing copper mine. The majority of experiments were carried out in 300mL Erlenmeyer flasks containing 150mL volumes of mineral suspension. Effects of some variable parameters such as solids concentration, pH and the concentrations of inorganic nutrients on the bioleaching of chalcopyrite obtained from De Xing copper mine were investigated. For a given concentrate the most important factor affecting the fractional copper extraction was the size of the mineral particles. The overall rate of leaching was found to be limited by the area of mineral surface. The attack started in cracks and genetic defects and finally reached the whole chalcopyrite surface. As a consequence of this, the ore showed strongly cracks. The additive of ferrous sulfate increases the bacteria activity, but did not improve chalcopyrite bioleaching. The results indicate that the nature and relative proportions of the various minerals present have been shown to be important factors.

Jan 1, 2014

By X. F. Cao

There was a large reserve of bauxite resources in China. And these resources were mainly the dias-pore-bauxite and contained plenty of aluminosilicate including kaolinite, illite and pyrophyllite. Reducing the contents of aluminosilicate would be significant to the using of Chinese bauxite resources. In this paper, from the single mineral flotation experiments, the surface properties and flotation beha-viours of aluminosilicate including kaolinite, illite and pyrophyllite, using dodecyl amine (DDA), N, N-dimethyl-dodecyl amine (DRN12) and N-dodecyl-1, 3-propane diamine (DN12) as collectors, had been investigated. The flotation results shown that the flotation behaviours of aluminosilicate had been influenced greatly by three amine collectors; and the effect was in the order of DN12>DRN12 >DDA. On the basis of FT-IR spectra and zeta potential measurements, the ionization of surface hydroxyl, as well as isomorphic exchange of surface ions, accounted for the mineral surface charges. And the mechanisms of interactions between the mineral surface and collectors mainly included two modes: electrostatic adsorption and hydrogen bonding; for the DDA and DRN>DDA. 12, the mechanism was mainly electrostatic adsorption; and for the DN12, the mechanisms of electrostatic adsorption and hydrogen bonding both existed. Results of quantum chemistry research shown that the collecting ability of amine collectors was greatly influenced by the electro-negativity of N in the amine molecules; and The |E(EHOMO| and ?E (HOMO-ELUMO) of N atom in DRN12 and DN12 were lower than that of DDA, and the positive charge of ?N group in DRN12 and DA12 were higher than that of DDA. All these calculation results could explain the collecting power of DN12>DRN12>DDA.

Jan 1, 2014

By X. M. Yu

A large amount of polluted sludge is produced by a nonferrous metal factory after treating waste water with lime/ferrous salt. The concentration of arsenic in the dried sludge is high to 5.84%, a toxicity test is taken on the sludge according to GB5085.3-2007 and the extraction content is 15.75mg/L, which surpasses the arsenic extraction standard [As]=5mg/L, the sludge is categorized as hazardous waste. If put outside without disposal, it would be very harmful to environments. Here we report an optimum protocol to extract arsenic; S2- alkaline liquor is utilized to treat the arsenic sludge. At 85?, 10L 7% S2- liquor is added into 1kg dried sludge and the resulting mixture is stirred for 120min at 250r/min, then separated by centrifugation and the compressed waste residue dried naturally. The average arsenic content is 1.40mg/L, lower than GB5085.3-2007 Standard and arsenic-free residue is consistent with GB18598-2001 Standard, which can be bury safely. The extracted arsenic is transferred into copper arsensite for use as addictive in copper electrolysis and the waste water can be recycle after calcium is removed.

Jan 1, 2014

By Daniel Saramak

"Issues concerning effectiveness of the high-pressure comminution process in technological circuits of copper ore treatment were presented in the paper. Crushing processes taking place in high-pressure grinding rolls devices (HPGR) are currently one of the most efficient methods of hard ore size reduction in terms of the energy consumption. The HPGR products are characterized by a fine particle size and the micro-cracks formation in individual particles, which appear in downstream grinding processes, decreasing their energy consumption. The purpose of this paper was to analyse the effectiveness of a ball mill grinding process depending on the changeable conditions of run for the HPGR crushing process. The research programme carried out included crushing tests in the laboratory scale HPGR device at various settings of the operating pressure volume and selected qualitative properties of the feed material (i.e. particle size distribution). Particle size distribution analyses of all HPGR products were performed and in the next stage the material was a feed to the ball mill grinding process. Grinding process kinetics were investigated through the determination of mass recoveries of individual particle size fractions after defined grinding time intervals. The models, defining the grinding process effectiveness as a function of changeable conditions of HPGR process run, were determined on the basis of obtained results. Based on these models the optimal grinding time in a ball mill was specified which is, in turn, the basis for optimization of operation of the technological comminution circuits for a given material type. The obtained results proved that the application of HPGR devices in a given copper ore comminution circuit may improve the effectiveness of the downstream grinding process which leads to improvement of the entire circuit work efficiency through decreasing the process energy consumption and enhancing product size reduction."

Jan 1, 2014

By Y. E. Brylyakov, M. A. Kostrova

"The apatite staffelite ores (ASO) of Kovdor deposit are dominated by fine-grained aggregates containing both phosphate minerals and silicates — vermiculite, smectites, zeolites. These minerals exhibit ion-exchange properties. In this connection, the magnitude of cation exchange, along with the content of P2O5 and CO2, is an important property of apatite staffelite ore, which largely determines the performance of concentration processes. In the examined ASO samples, the magnitude of cation exchange measured in terms of Ca2+ is 2546-4790 g/ton. The conducted laboratory studies of apatite staffelite ores with various mineral composition showed that adding calcined soda improves the recovery of P2O5 into the flotation concentrate. Full-scale tests were conducted at the apatite staffelite ore processing plant at Kovdor Mining and Concentration Operation and demonstrated the high performance of the proposed agent treatment. The test results showed that in the flotation of apatite staffelite ores, the optimum calcined soda feed rates range from 3,500 to 5,000 g/ton of the flotation feed. With close flotation feed and concentrate grade parameters, the P2O5 recovery gain is 17%. The effect of adding soda is associated with the desorption of the hardness cations from the minerals, precipitation in the pulp and, accordingly, improvement in the ionic composition of the liquid phase of the flotation feed due to a reduced content of calcium ions. Based on the test results, the proposed agent treatment with an elevated feed rate of calcined soda was implemented at Kovdor Mining and Concentration Operation in the flotation of apatite staffelite ore. The apatite staffelite ores (ASO) of Kovdor deposit are dominated by fine-grained aggregates containing both phosphate minerals and silicates — vermiculite, smectites, zeolites. These minerals exhibit ion-exchange properties. These minerals have certain properties requiring a more detailed examination for a better understanding of the flotation properties of apatite staffelite ores."

Jan 1, 2018

By I. A. Podkamennyi, O. E. Kovalchuk, G. P. Dvoychenkova

"Using the methods of electron microscopy and IR spectroscopy, mineral components in the run-of-mine kimberlites and on the surface of diamonds were identified. The mechanism and sequence of mineral formation on the surface of diamond crystals were established. Systematization and classification thereof were undertaken for the first time ever.INTRODUCTION The high content of diamonds sized -5 mm in the kimberlite ores of Western Yakutia determines their processing depth in the size class 0.5 mm and finer [1, 2]. These diamonds are recovered by grease and froth separation based on the natural hydrophobic properties of the crystals. When refractory altered kimberlite ores are fed into the industrial process, the performance of grease and froth separation of the diamond ore greatly deteriorates. [4, 10, 15, 17]. Altered kimberlites are known to contain up to 90% of secondary minerals. This reduces by up to 40% the recovery of diamonds by grease and froth separation. [6].Diamond crystals from the grease and froth separation tailings were investigated. On the surface of the examined diamonds, hydrophilic mineral formations were identified, responsible for reduced recovery by physicochemical separation methods [3, 12, 18]. The aim of this study was to identify and describe the relationship between the composition of kimberlite ores and mineral formations on the surface of diamond crystals in order to systematize, classify, and then develop methods of removal in grease and froth separation processes. MATERIALS Following materials were examined in this study: - kimberlites of various material composition, - resulting slimes, - diamond crystals from kimberlite ore processing products."

Jan 1, 2018

By James Y. Oldshue

"Very seldom is it possible when contacting a gas with a slurry to measure the dissolved gas concentration in the slurry, and even where possible, equilibrium data with a suitable Henry.s law constant are seldom available.In general, by assuming a reasonable value for the dissolved gas concentration in the slurry and a corresponding equilibrium gas partial pressure P*, KGa values can be calculated for the pilot plant and then scaled up. Then, with the same P* value at various reaction conditions, a mixer can be designed which is quite satisfactory, having a reasonable design factor for full-scale performance."

Jan 1, 2003

By L. Y. Zhang

The metallic sulphides in Jinchuan Mine are relative friable and the gangue minerals suffer of wide secondary change, the overgrinding of metallic sulphides and sliming of gangue minerals are the main cause that makes the mineral separation indexes difficult to improve. So changing the process of grinding, and classification, and optimizing the particle size distribution of grinding product is the key improving the separation performance of Jinchuan nickel and copper ore.

Jan 1, 2014

By L. X. Zeng

The low-grade nickel resource is very abundant in the western China. To make the best of the low grade nickel ore, we studied the process mineralogy and beneficiation process of nickel ore in the Yangliuping of Sichuan province. The grade of nickel is 0.45% in the nickel ore and the nickel exists in the sulfide including pyrrhotite, nickel pyrite, chalcopyrite primarily. The nickel distributes in pentlandite and magnetite over 90% and the copper does in the chalcopyrite over 95%. The carri-er minerals of useful elements tend to concentrate in space for concentration. As is shown in grain-size analysis of three major minerals, there are some more fine-grained grains with the percent of from 10% to 15% (<40 µm) and from 3.5% to 5.5% (<20 µm). So there will be some smaller size disseminated sulfide minerals difficulty to liberate in the process of concentration. The liberation degree of sulfide is not high and there are much associativity in the sulfides. Therefore, we should reclaim the sulfide aggregation dominating as pentlandite when concentrating. In addition, the sulphide minerals is so brittle that we should take care of preventing from crashing when grinding. The gangue mineral is mostly metamorphic mineral including serpentine, chlorite and amphibole which is easy to be argillization and difficult to concentrate.

Jan 1, 2014