Search Documents

By A. Güney, G. Önal

"The tailings of the Bigadiç Colemanite Concentrator at the West of Turkey which contain 18 % B2O3 and 1.57 % SO3 are collected at the tailing dams near the Concentrator. In this research, it was aimed to obtain colemanite concentrates with a minimum content of 40 % B2O3 and a maximum 0.5 % SO3 from the tailings. At the experimental studies, decrepitation methods were systematically applied following attrition scrubbing and sizing. At the end of the tests, the best decrepitation result were described, at 500oC temperature for 15 min. duration, the final concentrate having 57.84 % B2O3, 0.44 % SO3 with 73 % recovery was obtained.Boron ores reserves of Turkey are about 2.5 billion tons and Turkey has the 63% share of the World’s boron reserves. The boron reserves are located at Eskisehir (Kirka), Kutahya (Emet), Balikesir (Bigadic) and Bursa (Kestelek) districts in Western Turkey. In 2002, the total amount of boron production of Turkey was about 1.4 million tons, which is 40 % of the World boron production.Bigadiç colemanite (Ca2B6O11. 5 H2O) ore with a content of 30-31 %B2O3 are concentrated by attrition tumbling and classification process. So the final concentrates with contents of 40 and 42 % B2O3 are obtained at the size fractions of –125+25mm and –25+ 3 mm respectively. The tailings materials with an 18 % B2O3 content are collected at the tailing dams near the Concentrator. In this research, it was aimed to obtain colemanite concentrates with a minimum content of 40 % B2O3 and a maximum 0.5 % SO3 from Bigadic tailings having 18 % B2O3 and 1.57 % SO3.In experimental tests, attrition scrubbing, wet sieving, gravity separation, electrostatic separation, flotation and decrepitation were adopted to the colemanite tailings, and optimum beneficiation conditions were obtained."

Jan 1, 2003

By S. Q. Zhu

Coal Water Mixtures (CWMs) are densed suspensions of coal particles in water. Viscosity is one of the most important rheological properties of CWMs and it is desired to be as low as possible. The slurry viscosity was influenced significantly by additive formation, the particle size distribution and the ash content of the coal. However, the influence of dispersants is most obvious. At present, there are several kinds of dispersants such as polymeric styrene sulfuric sodium, lignin sulfonate, humate, polycarboxy salt, ethylene epoxide surfactant. In this paper, a newly synthesized CWM dispersant has been reported, which is an efficient anionic surfactants of polycarboxylic acid type. The synthesis process includes three steps. At the beginning, the polyglycol acetate ester has been performed by acetic acid and polyethylene glycol (PEO) on the condition of acetic-acid/PEO ratio 1:1.1, at 368~373K for 30 minutes. Then the macro-monomer is prepared through the esterification of 85.71% acrylic and 14.29% polyglycol acetate ester, at 368~373K for 10 minutes. After that, the polycarboxylic acid CWM dispersant is polymerized using proper proportion macro-monomer, acrylic (AA) and sulfonic styrol sodium, at 368~373K for 1 hour. This new dispersants are used in the coal water mixtures formulation. Four kinds of coal used in the experiment are Shuang Yashan, Tunliu, Luning, Changcun samples. ? The highest concentration for shuanyashan coal is 70% when the dosage of dispersant is 0.4%, and the content of -200 meshes particles is 75.53%. As the dosage of dispersant de-creases to 0.25%, the Shangyashan CWM concentration is 67%. ? For Tunliu coal CWM concentrations are in the range of 76% to 75% when dosage of the dispersant changes from 0.4% to 0.25% at the same particle size distribution of 83.5% minus 200 meshes. ? The highest concentration for Luning coal is 69% when dosage of the dispersant is 0.4%, and the content of -200 meshes particles is 88.86%. ? For Changcun sample, the coal concentration of CWM is 73%~75% when dosage range of the dispersant is 0.35%~0.5%. The experiments show that the synthesied dispersant is quite promising for some coals CWM preparation, but a little bit coal-dependent. The Proximate and Ultimate analysis, surface characteristic measurement have been made to investigate the interactions between coal and additives.

Jan 1, 2014

By B. Csoke

As opposed to large household appliances, in the processing of which dissambling has an important role, this possibility is pushed into the background as the size decreases. The practicable solution is physical liberation of the used small electronic household devices (by comminution) and separation of the liberated components according to their physical properties. In the first phase of the experimental work the structural/material composition of the typical products (mixer, kitchen robot, hair dryer, coffee machine, iron, bread toaster, vacuum cleaner, oil fryer) was determined. In the second phase a physical liberability test for each appliance using a rotary shear/shredder for crushing and a hammer shredder for milling was carried out. In the third phase the experimental separability tests using an air classifier and a shaking air table, as well as an eddy-current and an electrostatic separator were performed. In the present paper the results obtained using the air classifier and the electrostatic separator, are reported. To follow the life of a grain a new methodological procedure was elaborated. The particle size fractions after comminution were sorted into material fractions (copper, aluminium, plastics, etc.), then separated, and finally the recovery of the material components in the products were determined. Furthermore, the joint separability was investigated from two points of view: 1) for grain fractions and 2) for each waste appliance. According to the tests carried out so far, it was established that it is reasonable to form appliance groups by selection (e.g. mixer, iron, bread toaster and similar appliances form the first group, while the sandwich oven,

Jan 1, 2014

By Komar Kawatra, Joseph Halt

"Bentonite clay has been the traditional binder for iron ore pellets. However, bentonite increases pellets’ silica contents and is expensive. Researchers have proposed lowering bentonite doses by mixing it with other common binders. These mixtures may only be successful if the fundamental bonding mechanisms are understood. For example, what happens when bentonite (physical bonding) is mixed with fly-ash (chemical bonding)? What happens when bentonite is mixed with cornstarch (physical bonding)? In this paper, experiments are described where bentonite was mixed with various ratios of cornstarch and fly-ash, and pellets were agglomerated using 0.66 % w/w binder. Ca(OH)2 and CaCl2 were added as activator and accelerator, respectively, to the bentonite-fly ash mixture. Curves of pellet dry strength vs. bentonite-starch ratio were linear, suggesting the physical-physical bonding mechanisms were compatible - acceptable strengths (> 22 N) were produced at all bentonite-to-starch ratios. This was contrary to bentonite-fly ash mixtures, which displayed dry strength curves with a noticeable minimum due to competing binding mechanisms. Bentonite alone and fly ash alone produced acceptable strengths (> 22 N), but their mixtures resulted in weak pellets. Due to the positive results using cornstarch (CS) binders, the effects of CS solubility in water were investigated using two CS with high and low solubility (60 and 7.5 %). CS was premixed with bentonite at various ratios (0, 20, 40, 60, 80, 100 %). Pellets were agglomerated using 0.66 % w/w binder. The dry strength of pellets ranged from 50-300 N using the high solubility CS mixtures, and from 50-85 N using the low solubility CS mixtures. Fired strengths exceeded 2200 N/pellet at all bentonite-cornstarch ratios. This research showed that cornstarch solubility is an important factor in determining its effectiveness as a binder for iron ore concentrates, but significant work is still necessary before it can be used as a bentonite replacement."

Jan 1, 2014

By Anand Anupam

Conventionally, beneficiation in Indian coal washeries is done using dense medium cyclones upto the size of 0.5 mm. Coal fines below 0.5 mm size are extensively cleaned by froth flotation. There are many problems associated with flotation of Indian coals, e.g. poor response of coal particles to flotation, misplacement of fine high-ash material to froth, loss of good quality coarser coals (within ?0.5 mm size range) to tailing streams, high cost of reagents, water contamination, etc. In addition, sophisticated control systems for efficient management of the fines washing circuits are needed. Thus, there is an escalation in the capital and processing costs. In view of these facts, studies were carried out to establish the cleaning potential of dense medium cyclones for beneficiation of fine coal down to a size of 0.1 mm, essentially aimed at reducing the load on fine coal circuits mainly comprising of flotation. ROM Coal (in the size range of -2 + 0.1 mm) obtained from JogtaOCM,Jharia coalfield possessing relatively low ash (about 21%) was used in this study. Purpose for using low ash coal was to further lower, its ash content down to 8% which is comparable, to the ash content of imported coal. After characterization studies, nine tests were carried out on the prepared feed sample for its beneficiation using a dense medium cyclone of non-conventional design (very low cone angle and longer barrel), by varying its apex and vortex finder diameters. The efficiency of separation has been evaluated using Tromp curves. It could be established that it is possible to produce a clean coal of 8% ash, with Ep value of 0.044, using Jogta OCM coal by treating it in a modified dense medium cyclone. These results are summarized and discussed in detail in the present paper. Keywords: dense medium, cyclone, fine coal, beneficiation, Jharia coal

Sep 1, 2012

By B. Y. Tuo

This article presents results of studies performed to determine the feasibility of using low-grade limonite ores from Yunnan deposit. Laboratory tests and commercial trials have shown that the magnetic separation can be performed with a high high-grade concentrates. The quality of the preparation concentration meets the requirements for blast-furnace smelting. The results as a whole demonstrate the feasibility of utilizing bank limonite ore. Yunnan limonite?s magnetic separation, roasting magnetic separation and flotation experimental study shows that grade of the ore grade can been from 32.91% heighten to 58.64%, a recovery of iron is 90.87%, productive rate is 51% through orthogonal test optimization; roasting magnetic separation can obtain that the grade of iron preparation concentrate is 61.16%, recovery is 67.39%, productive rate is 36%. As far as economy and enviormental protection is concerned, strong mag-netic suggested a more appropriate process. Keywords: Limonite; Roast; Magnetic separation

Jan 1, 2014

By S. Banisi, E. Arghavani, Gh. Parsapour, S. Mousavi

Maximization of water recovery in thickeners is an essential step in the mineral processing industries. The Gol-E-Gohar iorn ore processing plant uses a center pier thickener with a diameter of 38 m and depth of 4 m. The feed rate is 50 t/h solids with a concentration of 5% (w/w), and it has been designed to provide an underflow containing 50% solids. The performance of the thickener was not as expected judged by the overflow stream containing 0.6% solids and water loss of 52 m3/h in the underflow. A criterion called the index of flocculation incorporating the perimeter-based fractal dimension of flocs, floc size, and settling velocities was proposed and used to determine the optimum flocculant dosage which was found to be 20 g/t. The fractal dimension of flocs in a pulp containing 5% solids was found to be between 1.16 (no flocculant) and 1.56 (40 g/t flocculant) which indicated highly branched and loosely bound structures for the flocs as flocculant dosage increased. At these conditions, the size of the flocs which was recorded by a digital microscope increased from 93 µm to 403 µm. A new feedwell with a special design with the aim of preventing flocs breakage and maximizing energy dissipation of pulp was constructed and installed. These modifications led to an increase in the thickener drivehead torque from 5% to 18% of the rated torque, indicating a higher bed depth. Finally, installation of a PID controller reduced the drivehead torque relative oscillation from 52.0% to 12.7%. These changes increased the solids concentration of the underflow from 49.0% to 56.9%, decreased the overflow solids concentration from 0.6 % to values smaller than 0.01% and resulted in a reduction of 27% in water loss in the thickener underflow.

Jan 1, 2014

By Y. H. Wang

Micro-flotation tests of spodumene, beryl, quartz and feldspar have been carried out by using CaCl2 and FeCl3 as modifiers and a blending collector of oleic acid and hydroximic acid. CaCl2 shows efficient activation for spodumene when pH is above 11.5, and FeCl3 exhibits a markedly activation and good selectivity for spodumene in the range of pH 4 to 10. The main species of CaCl2 are CaOH+ and Ca(OH)2 when pH is above 11.5, and the main species of FeCl3?6H2O are Fe(OH)+2 and Fe(OH)3 during the pH range of 4 to 10. A selective flotation of spodumene and beryl from pegmatic ore had also been completed while using FeCl3?6H2O as activator and the blending collector. A bulk concentrate containing 1.087% BeO and 4.70% Li2O has also been obtained in the flotation of spodumene and beryl from pegmatic ore assaying 0.097% BeO and 0.45% Li2O, and the recoveries of BeO and Li2O in concentrate are 74.38% and 69.50% respectively.

Jan 1, 2014

By P. M. Solozhenkin, V. N. Kovalev

Russia is a global antimony market leader. The three major antimony production provinces are Sakha Republic (Yakutia), Krasnoyarsk Territory and Trans-Baikal Territory. Russia’s largest antimony resources are Zhipkozhinsky and Solonechensky deposits in Sakha Republic (Yakutia) and Olimpiadinskoe deposit in Krasnoyarsk Territory. This work demonstrates the efficiency of computer programs and chemical technology aimed at the study of the behavior of collectors used in the processes of flotation of antimony, arsenic and Au (I – III) minerals. The most promising collectors for the flotation of ores containing antimony and gold on the basis of P(V) and compounds with S, O and N atoms were chosen. The mechanisms of interaction with the mixtures of two or three components of collectors were studied. High recovery of antimony and gold was reached in the processing of Au-Sb ores of Sarulah and Sentachan deposits in Sakha (Yakutia). X-ray radiometric methods of separation of antimony ores of Trans-Baikal Territory deposits were proposed. In order to choose the most cost-effective solvents for hydrometallurgical processing of Sb, Au-containing concentrates the method based on clusters formation between transition solvents and antimony minerals was suggested. The nature of Au losses was theoretically revealed in the sulfide-alkaline process. On the base of computer simulation, the formation of various complexes of (KAu) types was developed, for example, hydrosulphidic gold, thiosulfates of gold - Na3AuS4O6, antimony and arsenic gold, trithiostibate (III) and trythioarsenate (III) KAu were produced. The practice of processing of goldantimony concentrates to produce high-quality antimony trioxide and antimony-gold containing alloy (AGCA) regarding the special conditions of the Far North region, were analyzed. The affinage of AGCA was recommended. Creative project development of antimony industry in Russia in order to produce antimony compounds and pigments, including pyriform compounds and flame retardants (antipyrenes) is discussed.

Jan 1, 2018

By G. Alfano

This investigation is concerned with the optimization of ultrafine grinding of solids. It is focused on a dynamic classifier for recovering the fine fraction, for automatic recycling of the oversize particles and for reducing power consumption. Power consumption plays a major role in these energy intensive processes and depends on several parameters such as nature of the solid, degree of fineness of the finished product and, above all, grain size of the feed. This study indicates the optimal conditions for a dynamic classifier, that is, geometric characteristics of the apparatus and its capacity, inlet air flow rate and dimensions of the classification circuit. It is also shown that a mean grain diameter (dm) of about 2.00 µm with top size (dmax) of 50 µm can be achieved with an imperfection value of below 0.40 and energy consumption of 215 kWht-1. Keywords: air classification, dynamic classifier, jet mill, energy

Sep 1, 2012

By N. I. Um

The coal bottom ash generated from coal-fired power plant accounted for approximately 5 mil-lion tons in Korea. Almost all of coal bottom ash was treated as reclamation of the landfill because of the content of unburned carbon. For recycling of coal bottom ash, effective removal of that is required. So, in this study, the removal of unburned carbon by flotation was studied with respect to adsorption ability in surface of a bubble in order to consider its application to recycle the coal bottom ash. The sample A, B and C were that the coal bottom ash contained 2.73%, 7.01% and 10.49% of the unburned carbon (UC) respectively. The column flotation was carried out for each time as the artificial injection of air at 10.0L/min flow rate and the reagents of 500g/ton kerosene and 80g/ton MIBC were used. The samples per water of 1.3 liters were from 0.5% to 4% (w/w.%). In the result of this study, the kinetic curves of unburned carbon adsorption from injected air bubbles were in-creased rapidly as equilibrium was approached; only 5 sec was needed from the sample A and B and 10 sec was from sample C. And the equilibrium isotherms of unburned carbon adsorbed by the infected air bubble from the sample B and C could appear the BET adsorption isotherm; MT = KMEEO/(EO-E)[EO+(K-1)E](K: adsorption affinity), but not the sample A that was not enough to express the adsorption curve.

Jan 1, 2014

By N. Panteleeva, E. Konoplev, I. Michailova, S. Titkov, S. Aliferova, T. Gurkova, T. Chumakova

Cationic flotation using alkylamines and their derivatives as collectors, and characterized by high selectivity of mineral particle separation, is finding ever growing industrial application. In recent years the industrial application has been initiated of new cationic collectors - alkylmorpholines. Efficiency of cationic surfactants operation as collectors is dependent upon their colloid and sorption properties and the availability of silicate .carbonate rock-forming mineral impurities in the ore, which sorb the cationic collector. Investigations have been carried out on the influence of frothers and organic depressors with various compositions upon physical-chemical and flotation properties of alkylamines and alkylmorpholines. On the basis of these investigations requirements for organic depressor were developed and new flotation reagents were proposed (V-1 frother and KS-MF depressor). The use of new reagents enables one to decrease considerably the consumption of expensive cationic collectors and to enhance the floatability of coarse mineral particles. Data of new reagents industrial application is presented. The reagents developed can be used for flotation processing of other ores.

Jan 1, 2003

The addition of copper sulfate to mineral slurries in order to ?activate? sulfide mineral surfaces for enhanced collector molecule adsorption, and hence enhanced recovery via flotation, is a com-mon mineral processing practice. It has been established in a laboratory situation that the addition of CuSO4 in conjunction with xanthate collector increases the flotation rate of pentlandite as compared to the addition of collector alone. However, it remains unclear whether the addition of CuSO4has a similar effect within mineral processing circuits. We examine here the effect of pre-activation oxidation on the copper activation of pentlandite and monoclinic and hexagonal pyrrhotite. All activation experiments were carried out at pH 9 using a total solution content of copper ions equivalent to one monolayer (0.210 -4 moles, 110-4M). Copper loss from solution was extremely rapid in all cases with less than 10 % remaining after 10s. EDTA extraction and solution analysis clearly demonstrated that copper activation was via direct surface adsorption and not an ion exchange process, as is the case for sphalerite, and that most copper on the surfaces is in the form of Cu(I). ToF-SIMS analyses of the mineral surfaces subsequent to copper activation show increased surface oxidation on increased conditioning time prior to copper activation. However, there is a significant decrease in surface oxidation on comparison of samples that have otherwise been prepared in the same manner but where one has been exposed to copper solution rather than water. This suggests that copper activation stabilises the surface and reduces the propensity for oxidation. Regardless of the length of pre-activation oxidation time only Fe(III) (no Fe(II)-S) was observed by XPS analysis, indicating a highly oxidised surface layer dominated by Fe-O-OH species. The presence of Cu(II) on the mineral surface is indicative of the formation of Cu(II)-containing precipitates and indicates non-mineral specific activation resulting in increased recovery but lower grade. Mineral specific copper adsorption, as evidenced by the presence of Cu(I), is required to improve both grade and recovery. Prolonged oxidation prior to copper activation causes a reduction in the Cu(I) to Cu(II) ratio on the mineral surfaces as compared to either fresh surfaces or surfaces oxidised for 1 minute only. This strongly indicates that the copper activation process is less effective on highly oxidised surfaces.

Jan 1, 2014

By F. S. Niu

With the feature of finely-dissemination particle and complex mineral composition, oolitic hematite is considered to be the ore dressing difficult problem in the world. Series research on refractory oolitic hematite in Zhangjiakou Area are introduced as following: ore properties?technology mineralogy and mineral processing technology. The survey shows: with the fine grinding of the hematite to a fineness of -0.076mm 95%, obtaining iron concentrates grading 62.74% Fe at the recovery of 46.80% by high intensity magnetic separation- reverse flotation flowsheet; under the three stages intensity magnetic separation,four stages grinding and four stages gravity separation, getting the iron concentrates grading 61.09% Fe at the recovery of 45% using high intensity magnetic separation- gravity separation flowsheet; with roasting temperature of 800°C, time for 75~90min and ore-coal ratio of 11, gaining the iron concentrates assaying 62.74% Fe at the recovery of 87% by roasting- magnetic separation flowsheet. At present, this research is still doing for the target of raising the concentration recovery on the base of high grade concentrate. It is in the hope of fully utilizing the existing hematite resources in Zhangjiakou

Jan 1, 2014

By A. Gueciouer, A. Akkouche, K. Chalah, A. Benmounah

"Drilling solid waste is a typical industrial solid waste, and it is a major pollutant source to ecological environment. Generally, waste management dewatering systems separate solids and fine particles from the liquid phase of drilling fluid, thereby leaving a clarified aqueous solution and allow the cleaning of waste fluids. Typically, dewatering waste management systems clean drilling fluid through coagulation, flocculation and/or mechanical separation. Chemicals used in dewatering are based on the coagulation-flocculation process, which it facilitate the removal of suspended solids and colloidal particles. The factors which can promote the coagulation-flocculation are velocity gradient, contact time, and PH. The objective of this work is to optimize a formulation adequate for dewatering based on the coagulation-flocculation process used coagulant (Aluminum sulphate), anionic flocculants (Partially Hydrolyzed Polyacrylamide) and anionic polyelectrolytes (in solid form with linear chain with very high molecular weight). The results obtained show the good efficiency of the coagulant and flocculants. INTRODUCTION Rig site dewatering of drilling fluids with recycling of processed water can help an operator to comply with environmental rules by reducing volumes of waste and reducing long term liabilities. It can also reduce disposal costs and provide a cleaner drill site overall. Most of the environmental concerns during the 1980s involved hazardous materials and toxic wastes. Drilling fluids, many of which are chemically benign, have escaped many of the difficult-to-comply-with rules and regulations. During the 1990s, however, operators may be required to submit a written plan for liquid waste reduction for even nonhazardous materials. Many states and local agencies may institute total bans on oil field wastes. Drilling rigs typically produce about 1 bbl of liquid waste for every 1 ft of hole drilled. Thus, a typical drilling operation can produce a large quantity of waste [1]. To improve the dewaterability of sludge, different pretreatment processes have been widely studied and developed including thermal, chemical, magnetic, mechanical, acoustic, electric, electro-acoustic and their hybrid treatment processes [2]. Rig site dewatering (figure 1) is the process of injecting coagulants or flocculating chemicals into the mud entering a large clarifying centrifuge. Coagulation occurs when the solid and allowing it to be attracted to other solids by van der waals forces. Flocculation is the binding of individual solid particles into aggregates of multiple particles. It is physical, rather than electrical, and occurs when one segment of a flocculating polymer chain absorbs simultaneously onto more than one particle [3]."

Jan 1, 2018

By Takashi Furuyama, Sukeyuki Mori, Takafumi Okuma, Norio Hashiguchi

The Tower mill KD-3 is an improved version of the laboratory mills VD-1, KD-1 and KD-2 in which the classifying column has been modified to ensure a quick discharge of products from the comminution section and, on the other hand, a better separation of coarse and fine particles; the latter being collected in a cyclone with a central spiral ribbon. To level the circling airflow through the classifying column and have a strict control over the maximum size of collected particles, a series of experiments was carried out, modifying the internal structure of the column: insertion of a vertical plate, a cone, or a horizontal net. The relationship established between the maximum size of products collected in the cyclone and the duct airflow rate indicates that, independently of the latter, the insertion of a cone in the classifying column could stabilize the maximum size of products collected in the cyclone around 15.1 - 17.5µm. With a horizontal net, the maximal size could be reduced to 8.4 - 11.3µm. This occurrence might result from the collision of coarse particles blown from the comminution zone with the base of the inserted materials and their settling down the bottom of the classifying column.

Jan 1, 2003

By M. Wierink

The lifecycle of a resource, specifically a metal, is often depicted as circle from primary production from mining to minerals processing and via manufacturing and use to disposal and recycling. When a material is recycled, it is considered as saved energy compared to producing the material from primary source. This is, however, a simplified representation. At each step of the life cycle, there are changes in the quality of the material due to different materials chemical and physical interaction, phase transformations due to diffusion, radiation etc. Due to these physical and chemical phenomena there are losses of material, which as determined by thermodynamics are not recoverable within the life cycle. This can be considered as an increase embodied energy per mass unit of substance and loss exergy from the material cycle. With low cyclic loss, the material will remain in the recycling loop for a long time, while with high cyclic loss it will disappear fast. Where you put the material determines how fast it disappears from the resource cycle. In this research paper the phenomena of quality degradation of material and idea of increase of embodied energy and exergy loss within a resource cycles is portrayed. The cyclic nature of material states and transitions and energy consequences of material quality degradation as well as the parameters affecting the length of the time scales of the material cycles are described. Currently the cyclic embedded energy and the history of material is not taken under consideration in generic life cycle assessment. This easily results into a conclusion that lifetime of product is optimized only in terms of how much energy an appliance uses during its lifetime, while ignoring the loss of embedded energy due to the effects caused by the environs the material is subjected to during the cycle. Better description of the time properties of material give us a possibility to design toward optimum lifetime of products in terms of resource efficiency. Keywords: product lifetime, material lifetime, recycling, cyclic resource efficiency, material state, material quality, exergy, embodied energy

Sep 1, 2012

By V. A. Feofanov

Technogenic water of ore mining enterprises, nonferrous metals operations, the enterprises of electroplating and instrument making, containing copper in the form of those or other connections can serve as perspective sources on receiving the copper-bearing raw material. Extraction of copper from the given water also solves a problem of water treating from a toxic component that reduces environmental load at evacuation of water in an open basin. The method of case hardening allows extracting copper selectively with reception of a deposit with the content of copper up to 70%. Weakness of the method is its efficiency basically in acid reduction, and also its low degree of copper extraction. On the basis of case hardening the method of galvanic coagulation is devised. It is based on the work of a short-circuited galvanic cell of iron-coke at variable contact of coupled metals components among themselves, cleared by the oxygen of air. The following processes of galvanic coagulation are considered: ? Extraction of copper; ? Formation ferrites of copper; ? Copper sorption on just-aggregated oxide forms of iron. Establishing conditions for passing the given stages provides an opportunity of copper extraction from technogenic water at any value of ??, content of salt and concentration of copper with reception of a compact deposit from which it is possible to extract copper by the known ways of enrichment and metallurgy. Investigations on optimization and intensification of galvanic coagulation with the purpose of reception the maximum rich deposit on copper have shown that the average contents of copper in a solution of 100~200 mg/dm3 the contents of copper in a deposit is 6%~10% at extraction 85%~90%, depending on characteristics of treated technogenic water. Using methods of scanning microscopy it is determined structures, composition and mechanism of phase formation in investigated electro-chemical process. The second stage of galvanic coagulation increases a degree of copper extraction up to 98%~99% that allows returning the cleared waters in circulation for waste recycling or evacuation in an open basin. Nowadays the method of galvanic coagulation is the most acceptable for copper extraction from technogenic water both from the point of view of efficiency and instrument setting that allows applying the method in conditions of the working enterprises.

Jan 1, 2014

The characteristics of mineral resources and tailings resources in China are analyzed. Those tailings, which have double characteristics, can occupy land, pollute environment and even influence human habitat if they are not disposed in time. So pay attention to the comprehensive utilization of the tailing more and more both at home and abroad. The present situation and problems in comprehensive utilization of iron tailings in China are introduced by combine some practice experience, and have looked forward to the comprehensive utilization of iron tailing situation.

Jan 1, 2014

By Bulelwa Ndlovu, Saeed Farrokhpay, Dee Bradshaw

The effects of phyllosilicate minerals on the flotation performance and froth stability of a copper ore was investigated. It was found that various phyllosilicate minerals affect the copper recovery differently however they all caused the flotation grade to be reduced. The effect of different phyllosilicate minerals on the froth stability followed the order of talc >> montmorillonite > muscovite > kaolinite > illite. The results demonstrated that there could be a relationship between the deleterious effect of phyllosilicate minerals on the flotation and froth stability. Talc and montmorillonite have both shown the highest effect on the flotation recovery and grade as well as froth stability. On the other hand, illite has the least effect on the both flotation performance and froth stability. Kaolinite and muscovite also affected the copper flotation grade (but not the recovery) while they also affected the froth stability. Therefore it is possible to control the flotation performance when phyllosilicate minerals are present via monitoring and controlling froth stability which needs to be investigated further.

Jan 1, 2014