Search Documents

By P. Condori

In spite of the importance of the slurry transport and discharge in autogenous and semiautogen-ous (AG/SAG) mills, it is evident that a more comprehensive and useful model is still required. Semi-empirical models used up to now have many limitations and cannot be used beyond the ranges in which they were developed. The breakage of particles as they are transported along a mill com-plicates the experimental analysis and the modelling of the transport process within the mill. The interaction of the grate discharge and the pulp lifters, with the added issue of backflow from the pulp chamber into the mill, makes the discharge modelling process difficult. In order to overcome these difficulties, a mechanistic approach has been applied. The general transport and discharge model was subdivided into four independent models: Flow through the charge, flow through the grate, flow in the pulp lifter, and flow-back. This paper gives an overall description of the modelling approach and discusses in particular the modelling of transport of fluids through the charge. In order to evaluate and calibrate the model, experimental work was carried out. To evaluate the gradient pressure under different conditions of charge packing and flow rate, a specialised experimental rig with a highly sensitive pressure gauge was used. Preliminary results identify the differences of the charge and grate on the restriction of flow. The existence of a dynamic voidage in our particular system was more evident and as a result, a semi-empirical correlation for the voidage was developed. In general, results show that the me-chanistic model derived from Ergun?s equation for flow through a packed bed can be satisfactorily adapted.

Jan 1, 2014

By Mauricio Guimarães Bergerman

At the regrind or secondary grinding stages of base metal ores, the concern about energy efficiency is usually extremely important. In general, the specific energy consumption at this stage is higher than during the primary grinding stages. In addition, a tendency of finer grinding has been observed in the new projects of metallic minerals, due to the finer mineral liberation, which leads to increasing capital and operational costs. At Vale?s new copper projects in Brazil, regrind sizes with a P80 of approximately 40 to 20 µm have been necessary. Conventional ball mills, adequate for primary grinding, usually bring about low energy efficiency with products bellow 50 µm. Vale is using the vertical mill on its copper projects ? Sossego and Salobo, in order to optimize the regrind of rougher concentrates and reduce energy consumption. This paper presents the results of industrial surveys carried out on the Vertical mill circuits of Sossego plant during its initial years of operation, and compares these results with the design criteria and laboratory regrind tests used for the mill scale up. Keywords: grinding, regrinding, copper, vertical mill, stirred mill

Sep 1, 2012

By S. Banisi, O. Farshid, M. R. Rozebehi, A. Bahar, A. Arghavani, M. Mahdavi

At the rougher flotation circuit of the Miduk copper concentration plant (Kerman, Iran) five column cells (CISA) with the diameter of 4m and height of 12m using static mixer type (MicrocelTM) spargers have been installed. Based on the initial design, columns should accept a feed rate of 625 t/h with 80% passing size of 90 µm and solids concentration of 28% and produce 88% of the plant concentrate (i.e., 22 t/h) containing 32% copper. Due to mechanical and processing problems this objective was never realized and theses columns were remained out of operation from the commissioning time (2005). A new attempt with the aim of returning these cells into operation started in 2013. The results of an extensive study indicated that spargers plugging due to the entrance of small amount (2 kg) of coarse particles (up to 2.5 cm) because of usual problems at the plant environment was the main reason of columns non functionality. With a change in the recycle pump inlet design to the column, which prevented the entrance of coarse particles to the spargers, the operation of the column significantly improved. It was found that in order to have a stable operation of the columns at the rougher stage the feed rate for each column should be reduced from 125 (design) to 70 t/h. The air superficial rate had to be also reduced from 1.9 (design) to 0.6 cm/s. A period of 10 days of continuous operation showed that the carrying capacity was 0.23 (g/min/cm2) which was significantly lower that of the design value (i.e., 0.58). The gas hold up was found to be lower than 10% beyond which columns started to move to the turbulent state indicated by "boiling" froth. The average life time of spargers was determined to be 20 days which considered to be very short. The average recovery and concentrate grade of these columns were found to be 68% and 32%, respectively. The high wear rates of spargers, unusually high level of maintenance and supervision needed and instability of the operation made the plant managers not to use column cells as the roughers.

Jan 1, 2014

By S. A. Vorobyev, Yu. L. Mikhlin, Ye. V. Tomashevich, A. A. Karacharov, M. N. Likhatski1, A. S. Romanchenko, S. V. Saikova

"A set of state-of-the-art methods have been applied to study ultrafine particles and nanoscale species arising on mineral surfaces upon milling, interaction with flotation reagents, and leaching of base metal sulfide ores in order to gain insights into interfacial mechanisms. The fine fractions produced by ball milling of a Pb-Zn Gorevsky ore and four Cu-Ni sulfide ores studied with laser diffraction, dynamic light scattering, zeta-potential measurement, Xray photoelectron spectroscopy (XPS), SEM, TEM and other techniques. The particle size distributions had, aside from the peaks at 20-60 ?m, maxima near 1-2 ?m; the flotation was considerably suppressed when the yield of positively charged ultrafine particles approached tenths % (several kg per ton). High-energy XPS and X-ray absorption spectra revealed that sulfide minerals depleted in metal in air and aqueous solutions were composed of outer “polysulfide” layers, strata with disulfide species, and heavily defective underlayers, and “passivation” was explained by stability of the metal-deficit structures. Dixanthogen at pyrite and copper-activated sphalerite, dixanthogen and then cuprous xanthate on chalcopyrite, and chemisorbed xanthate at galena were specified as the main interfacial products using cryo-XPS of fast-frozen flotation slurries. The particle size, zeta-potential and behavior of colloids of Cu and Pb xanthates and dixanthogens were largely determined by the initial ratio of a cation and collector; the properties of copper xanthate nanoparticles were also affected by incorporated dixanthogen (about 15 wt.%). Submicrometer gas domains of 3-8 nm in height and “hydrophobic” forces upon the probe retraction were found on xanthate-treated minerals using atomic force microscopy and spectroscopy; their impact on flotation is briefly discussed.INTRODUCTIONInterfacial phenomena play a key role in flotation, leaching, water purification and related environmental processes. The mineral processing and extraction of metal from sulfide ores commonly involves milling the ore, which produces, along with the particles of 20 µm to 100 µm, mineral entities ranging from micrometer to submicrometer and nanometer scale. Furthermore, ultrafine particles of flotation reagents, products of metal sulfide oxidation, and so on may form spontaneously and accumulate in production water, flotation froth, deposit on mineral surfaces, affecting the flotation performance, and then enter waste waters, mine and natural drainage, polluting soils, surface- and ground waters (Miettinen et al., 2010; Wang et al., 2014). The efficiency of flotation and hydrometallurgical recovery of values, environmental issues are crucially dependent on the state of mineral surfaces. Particularly, it is generally accepted that the surface non-stoichiometry of sulfide minerals induced by oxidation and leaching should affect their hydrophobicity and reactivity, including so-called “passivation”, but the nature of such surface layers are still a matter of controversy (see, for example, Holmes and Crundwell, 2013). Another phenomenon attracting rapidly growing interest in several areas is low-dimensional gas species (“nanobubbles”) at hydrophobic surfaces that may play a decisive role in particle-bubble attachment in flotation but remains scarcely investigated up to now (Xing et al., 2017). Here, we survey our recent results on the abovementioned problems applying a series of rather new methods and approaches; more details can be found in refs. Karacharov et al., 2016; Mikhlin et al., 2015; 2016; 2016a; 2016b; 2016c; 2016d; 2017; 2017a; Vorobyev et al., 2017."

Jan 1, 2018

By B. Das

Waste water produced from coal preparation plants posses several problems during dewatering and solid/liquid separation. The natural sedimentation rate of the particles present in colloidal and finely divided suspended form is very slow. Flocculation technology is being applied in most of the coal washeries to recover water which is being accomplished through the use of inorganic salts, polymeric flocculants or both depending on the chemical and physical characteristics of the pollutants present in the waste water. The waste tailing water from Piperware coal preparation plant, Central Coalfield Limited (CCL), India, is highly turbid containing ~ 16000 NTU with negative surface charge in the pH range of 2 to 10. Polymeric flocculants in conjunction with fine magnetite is investigated to achieve faster settling rate with lowest level of water turbidity. The conditions affecting the interaction between the reagents and the turbid particles present in the tailings water are investigated. It is possible to bring down the turbidity of the water to < 90 NTU from very high turbid tailing water by using 2 mg/L of the polymeric flocculent in combination with 0.1 g/L of magnetite at natural pH of the tailing slurry. It has been found that finely divided positively charged magnetite particles in combination with the flocculent selectively coat the negatively charged impurities present in water and thereby increase the settling rate under the influence of a magnetic field.

Jan 1, 2014

By Caibin Wu, Ali Lei, Ningning Liao, Jingsheng Ye

"The particle size distribution characteristics of ground product can influence the quality of the classification overflow and the next beneficiation indexes in an ore concentrator. Usually, the size distribution of ground product is considered to be determined by that of new ball mill feed. However, based on large amounts of data from industrial grinding circuit surveys, this paper has clearly shown that the size distribution of ground product should be determined by the size characteristics from classification underflow unless the circulating load was small, because the new feed is an important component and occupy a dominant position of mixed ore from belt feed and classification underflow. On the other hand, the correlation coefficient of the size distribution between ground product and classification underflow can be more than 0.99 when the relevance principle and its method are used. Meanwhile, their P80 value also keeps a synchronous correlation. The greater the capacity of classification underflow is, the higher the correlation of size distribution between the ground product and the mixed feed is. Furthermore, the correlation coefficient of the size distribution between ground product and classification overflow which is from primary or secondary can be 0.96. It is another discovery that the correlation coefficient is related to the type of classifier. The coefficient of size distribution of overflow and underflow from hydrocyclone is superior to that of spiral classifier, which can explain the reason why the hydrocyclone is widely used to replace the spiral classifier in concentrator.INTRODUCTION It is well knows that ball mill circuits closed with cyclones or spiral classifier such as a primary grinding circuit, a secondary grinding circuit and SAB mill have become an industry standard. Which grinding process employed will be determined by the P80 value of ground products. When the primary closed circuit ball mill or SAB that it is different throughout between the two processes was employed, a grinding fineness with -200mesh under 68% will be available. However, the secondary grinding circuit with the fineness of -200mesh above 80% can be conducted. Of course, the grinding fineness is determined by the grain size characteristics of the mineral."

Jan 1, 2018

By Montaser S. EL Salmawy, Takahide Wakamatsu, Eishi Kusaka

"The effect of ethoxylation of long chain alcohols on the quartz and feldspar flotation behaviors was investigated for surfactants of the octylphenol polyoxyethylene family. The tests were carried out with an average of 7.5 (Triton X 114), 9.5 (Triton X 100), 30 (Triton X305), 40 (Triton X 405) and 70 (TritonX 705) oxyethylene units. Electrokinetic and flotation studies on quartz have shown that at low pH values, quartz could be floated with polyoxyethylene octytlphenols. The possible mode of adsorption of these nonionic surfactants may be suggested to be due to hydrogen bonding between the oxygen of ether and hydrogen in the free hydroxyl groups on quartz surface. It was anticipated that the selectivity between quartz and microcline would decrease as oxyethylenic chain length increases.Electrokinetic methods were used to elucidate the mechanism of surfactants adsorption and to correlate these findings with the optimum flotation conditions. The polymeric surfactants would reduce the negative values of zeta potential of quartz while the reverse is true for feldspar. After treatment of microcline with HCl, its electrokinetic behavior in the presence of Tritons X surfactants became similar to that of quartz.The obtained results would suggest that separation of quartz from feldspar using nonionic surfactants of octylphenoletoxylated alcohols having shorter oxyethylenic chain length at low pH could be achieved"

Jan 1, 2003

By Paolo Bevilacqua, Paolo Antonini, Lorenzo De Lorenzi

"Italy is one of the major producers of ceramics in the world. Ceramic production requires large quantities of K-feldspar, which is commonly sourced from granites, alkali-granites, and “granitic” sands. These rocks contain other minerals, such as quartz, plagioclase and mafic minerals, which are undesirable for ceramic production. Due to the coarse mineral grains that constitute these rocks, a reasonable liberation is achieved at a relatively coarse grind size.This paper reports a study conducted on the separation of K-feldspar from quartz, plagioclase and biotite, from a feed of ground granite. The feasibility of the separation using a dynamic dense medium separation system has been investigated, as an alternative to the traditional flotation technique. The use of a two stages cylindrical vessel (Tri-Flo) was preferred to a conical vessel, due to the improved separation efficiency. Tests were conducted on two samples of crushed granite having size distributions of –3 +1 mm and –1 +0.5 mm.Heavy liquid analysis was performed on the two samples. As the rheological properties of the dense medium interact with the separation efficiency, the stability and viscosity of the dense medium were controlled and kept within an appropriate range; which was achieved with the addition of an artificial contaminant (clay) to the dense medium."

Jan 1, 2003

By Tong Guan, Guangqin Fu, Lihong Deng, Xiaotong Zhou

The raw ore contains many kinds of valuable metal elements. It is rich in valuable metal elements, such as Pb, Zn, Sb, Sn, Ag and is associated with S,Fe,As,In,Cd. A new technology which includes medium intensity magnetic separation, preferential lead flotation, zinc-sulfur bulk flotation, zinc-sulfur flotation separation, tin gravity separation and tin slime flotation was chosen to recover valuable minerals in the raw ore, and the iron concentrate, the lead concentrate, the zinc concentrate, the sulfur concentrate and the tin concentrate can be obtained. To the zinc-sulfur bulk concentrate with the grade of 7.21%Zn and 16.97%As acquired by the zinc-sulfur bulk flotation, two different flowsheets of Zn-S separation technology are chosen to study. The lab test shows that when using lime+DM as depressor, the zinc concentrate assaying 47.73%Zn with the recovery of 95.01% can be obtained and the test indexes are better than that of the flowsheet which using lime as depressor. At the same time, the Cd content is 0.65% and the In content is 0.10% in the zinc concentrate, so they all reach the smelting comprehensive recovery standards and the As content decreases to 0.23%. Finally the flotation separation of christophite and As-bearing sulfide minerals can be successfully realized.

Jan 1, 2014

By Guanghua Ai, Xiong Huang, Huashan Yan, Ting Li, Tingsheng Qiu

"Cyanide tailings of gold and silver concentrates contain considerable quantities of copper-lead-zinc sulfide minerals that can be recovered. However, the strong inhibition effect of cyanide often makes it difficult to recover these sulfide minerals effectively. In this research, a sample of cyanide tailings was investigated based on the principles of process mineralogy; activating flotation tests were carried out for the target minerals in the tailings, and the activation mechanism of the activator and its influence on the target minerals were investigated by Fourier transform infrared spectroscopy (FTIR). Mixed flotation of copper and zinc was carried out using QJ-01, a combined agent containing sulfite, as the activator of copper and zinc minerals, and ammonium dibutyl dithiophosphate (ADD) and butyl xanthate (BX) as the combined collector. Copper concentrate was obtained from the mixed concentrate by using a combined inhibitor of sodium sulfide and zinc sulfate to inhibit the zinc mineral. Zinc concentrate was extracted from the copper tailings by using copper sulfate as the activator and BX as the collector. The flotation test yielded copper concentrate with a grade of 22.56% and recovery of 76.96%, and zinc concentrate with a grade of 42.56% and recovery of 82.29%, which shows that comprehensive recovery of the sulfide minerals – copper and zinc –from the cyanide tailings was realized. The FTIR analysis showed that CN- was chemisorbed on the surface of chalcopyrite and sphalerite following cyanide treatment, while the combined activator QJ-01 containing sulfite reduced CN- into SCN- and weakened the complexing ability of CN- with metal ions on the mineral surface, thus achieving a good activation effect on chalcopyrite and sphalerite. The results of this study can provide practical guidance in increasing the resource utilization ratio of cyanide tailings in gold mines, and thus contribute to alleviating environmental problems caused by stockpiling cyanide tailings. INTRODUCTION Cyanidation, the most widely used technology for extraction of gold, has several advantages such as high recovery, process maturity, low cost, etc. According to available data, the annual discharge of cyanide tailings from China's gold mines exceeds 20 million tons (Li et al., 2011). Lower grades of exploitable gold ore entail increased discharge of cyanide tailings. Huge quantities of cyanide tailings are regarded as waste and stored, resulting in significant wastage of land resources. Moreover, residual beneficiation reagents, cyanide ions, and heavy metal ions in cyanide tailings cause severe pollution of water and land (Laitos et al., 2013; Donato et al., 2007; Mudder and Botz, 2004). In addition, cyanide tailings often contain valuable elements such as gold, silver, copper, lead, zinc, sulfur, and iron, which, if not recycled, would result in considerable wastage of resources. Hence, it is imperative to study the reduction and safety of cyanide tailings, and the mineral resources present in them."

Jan 1, 2018

By Y. H. Zhang

Mechanism of BK501 in desiliconization from bauxite was studied by use of flotation test, EDS, ?-potential, FTIR. Results of flotation show that almost all of diaspore can be depressed when BK501 is put into pulp ranging from pH 4~12, in the meanwhile kaolinite is slightly activated. In the light of surface analyses, it is concluded that the adsorption of reagent on the diaspore is dominant by chemical interaction. Moreover, kaolinite may float more by addition of BK501 because of flocculation.

Jan 1, 2014

By Aysan Molaei, Kristian Waters

Solvent extraction is the one of the most common techniques for recovering metal ions from aqueous systems. However, solvent extraction is generally limited to relatively high concentrations and requires a high organic/aqueous ratio. Predispersed solvent extraction (PDSE) is a modified solvent extraction technique in which organic phase pre-comminute into colloidal liquid aphrons (CLAs). In this study, the extraction of copper by the PDSE technique was investigated. The main focus of this study was on the characterization and application of CLAs under different operational conditions, and to investigate the effects of different parameters on the extraction of copper from dilute streams. The effect of phase volume ratio (PVR), initial extractant concentration and initial copper concentration was studied and optimum conditions for copper removal using CLAs generated by LIX 984N as extractant, oil soluble and water soluble surfactants were proposed. Experimental observations indicated that PVR and initial LIX 984N concentrations had a significant effect on copper extraction.

Jan 1, 2014

By Xianjun Lu

This paper presents gold occurrence investigations on the altered rock gold deposit from Jiaodong area of China, and comparisons of gold occurrence in the ore samples from different mining levels. According to the results, the chemical and mineral compositions of raw materials from different mining levels are quite similar. However, the relative content and grain size of gold minerals are quite different between the two mining levels of -130m~-340m and -550m~-650m. In the ore of upper mining levels of -130m~-340m, electrum is the dominant gold mineral and accounts for about 80% of the total gold minerals, while native gold is minor and accounts for about 20%. As for the ore of deep mining levels of -550m~-650m, the major gold mineral shifts to native gold which accounts for 67%, while the ratio of electrum drops to about 33%. Coarser gold grain size was observed in the upper mining level ore with a mean size of 33.05µm while the gold grain size was much finer in the ore of deep mining levels with a mean size of 22.85µm. Furthermore, the gold mineral associations also show different patterns between the upper mining level samples and the deep mining level samples. Of the three observed gold association types such as inclusion gold, fissure gold and interparticle gold, more inclusion gold was found in the ore of deep mining levels. The inclusion gold accounts for 62% in the ore of deep mining levels, while that in the ore of upper mining levels accounts for about 56%. Further study revealed that the dominant gold associated minerals are pyrite and sulphides and only a small amount of gold is associated with quartz and silicates. It was shown that the altered rock gold ore from Jiaodong area can be regarded as a free milling gold ore, but the processing parameters should be optimized for the ores in different mining levels according to the different gold occurrence. In addition, it was predicted that enhanced gold liberation is necessary for the ore in deep mining levels.

Sep 1, 2012

By Jochen Petersen, David G. Dixon

"Although heap leaching may be perceived as a somewhat low-tech route for the extraction of low-grade minerals, the underlying physical, chemical and biological processes are in fact extremely complex. There has been increased interest in heap leaching of sulphide minerals in recent years with the advent of controlled bio-heap leaching, and the need to mine more marginal ore deposits.A detailed investigation into the dynamics of heap leach processes has provided much insight into the underlying complexities, and has led to the development of a sophisticated modelling tool, HeapSim. Some of the sub-processes that are modelled include mineral kinetics, particle size effects, bacterial growth, oxidation and adsorption, gas adsorption, pore diffusion, bulk advection, gas balance and heat conservation. The interplay of these various sub-processes is illustrated in the paper.Two case studies are presented which illustrate specific features of the model for different applications and how these have helped to identify key areas of concern. The first is focussed on chalcocite heap bioleaching, which shows that by nature of the reaction the process is strongly dependent on the initial supply of acid to the mineral site. In heaps this acid supply can be severely limited by the rate of diffusion from channels of flowing solution into stagnant zones of the heap, whereas in narrow-bore laboratory columns this effect is not observed."

Jan 1, 2003

By ?. S. Potokin

"In general the electric pulse treatment is composed from two processes – electric pulse grinding and electric explosive (electric discharging) activation. The electric pulse grinding with the effect of selective destruction refers to a major slag fraction, more that 2-5 mm, when a one can see a physical prerequisites for electrical breakdown of the slag particles. The electric pulse treatment of slag is considered as an additional operation in the technological scheme extraction of non-ferrous metals from copper smelting slags in addition with mechanical grinding, flotation enrichment and acid leaching. Studies of the reprocessability of pelletized slag have shown the possibility of higher extracting non-ferrous metals via flotation after electric pulse disintegration (EPD) treatment. By using EPD of slag pellets, it is possible to increase the non-ferrous metal yield to concentrate by 18-24%.INTRODUCTION The use of the explosive effect of the plasma discharge channel at electrical breakdown of a solid at a pulsed high voltage is the physical basis of the electric pulse method of destruction of geomaterials (Vorobiev et al., 1971; Andres, 1995; Semkin et al., 1995). The flowing of a pulsed current in the discharge channel is accompanied by a sharp increasing of plasma’s temperature and pressure, leading to a supersonic expanding of the discharge channel, the formation in the solid of intensive mechanical tension field, spreading of cracks, and eventually, to the destruction of the solid. Fragmentation and grinding of ore and mineral aggregates by electric pulse method due to a number of specific physical mechanisms of power load and crack formation, belonging only to this method, is different by high selectivity of destruction. This ensures better liberation of grains of individual minerals and their better preservation from destruction and less formation of a slurry output. These features creates the prerequisites for a more complete extraction of a useful mineral in the concentrate during ore dressing, to improve the quality of concentrate. In contradistinction to mechanical methods, electric pulse technology does not contaminate the product with instrumental metal, material of lining and grinding bodies. The possibility simply and in a wide range to change the dynamic load character allows to regulate the granulometric composition of the product of grinding, to obtain a narrower class of product size than is possible with mechanical grinding. The product of electric pulse grinding is characterized by less roundness and large specific surface area of grains due to the trait, that a new surface is formed in the process of splitting during the expanding of cracks. The degradation product has increased sorption and reactivity in chemical reactions. Liberation of the mineral inclusions particle better corresponds to their initial natural state in the rock and this is the great importance for the study of mineral raw materials."

Jan 1, 2018

By Wayne van Drunnick, Mervyn Ruthnasamy, Olvier Guyot, Christophe Bouché

"Anglogold’s Mponeng Mine is situated in South Africa’s North West Province approximately 80km from Johannesburg. The reefs being mined in this area are among the deepest deep level mining operations in the world. These shafts often exceed several thousand meters making these operations complex and expensive.The gold plant is fed with run-of-mine ore which is stored in mill silos. Feedrate to the mills is controlled by a variable speed belt. Three parallel SAG mills (4.85 x 9m) treat 80-100tph, operating in closed circuit. Hydrocyclones classify the mill discharge, returning the oversize to the mill feed. Cyclone feed density and pressure are measured and are used with typical control loops to determine water addition rates to the mill. Control loops at PLC/SCADA level were historically used with limited success in the control of the milling circuits. Mill control for an installation of this type used mill mass (measured by load cells) and feedrate to control throughput. An online particle size analyser (PSI) was installed to assist grind control in tandem with pressure/density control on the cyclones. Although the accuracy of the measured grind was reliable, long term consistency of the PSI could not be guaranteed. Economic pressure from the business sector requires consistent mill throughput at optimum grind conditions. Fluctuations in production targets can manifest due to inconsistent control and the lack of real-time information from the process.This sensitivity to process movements may vary between shifts and also with changes in ore competency.Whilst tools are available to improve control, few have the sensitivity to process movements to provide real-time information for optimal grind control. For this reason an Advanced Control solution was sought. Advanced Control is often described as the supervision of basic PLC/SCADA control. Advanced control systems have to seamlessly compliment the existing control strategy and bridge the gap that exists between basic control and optimised control. A solution was found in the Metso Minerals CISA’s OCS (Optimising Control System). This French designed system makes changes to process setpoints to achieve peak performance and is distinguished from others by its soft sensor capabilities. The soft sensor is an embedded module in the OCS package that can be configured to estimate values normally obtained from field instruments. Advanced control using a Fuzzy Expert System assisted by Statistical tools (such as moving averages and a Soft Sensor using Phenomenological Models) would serve to bridge that gap. Metso Minerals CISA’s OCS is a modular system with various capabilities.It was successfully used to provide on-time process information via Soft Sensors. Circuit stability was achieved using Rule Based Expert Control in complete synergy with Fuzzy Logic. Two rule-based strategies were developed for this circuit. The first uses the online product size analyser as a primary control variable. The second uses a calculated kWh/t value and a modelled mill discharge density as primary control variables. The latter had more availability than the particle analyser and is currently in use."

Jan 1, 2003

By Zhu Yangge, Hu Xiaoxing, Feng Qiming, Zhang Guofan, Zhang Xingrong

"During the flotation process of ilmenite and titanaugite with fatty acid as collector, unavoidable ions such as Ca2+, Mg2+, Al3+, Fe3+ and Fe2+ demonstrate considerable influence on the floatability of the minerals. In this study, flotation test, zeta potential test, and solution chemistry calculation were adopted to investigate the mechanism of how these metal ions affect the floatability of ilmenite and titanaugite in different pH conditions. The results show that in weak acidic solution, Ca2+ and Mg2+ mainly freely exist in the solution with little adsorption on mineral surface, and their reaction ability with oleate ions is weaker than active site on ilmenite surface (Fe), thus they show negligible effect on the flotation of ilmenite; Al3+ shows similar reaction ability with oleate ion compared to Fe3+, which lead to competitive reaction with collector, so the flotation of ilmenite is depressed. While Fe3+ can adsorb on surface of titanaugite in the form of Fe(OH)3, and it shows stronger reaction ability with oleate ion compared with active site on titanaugite surface (Ca and Mg), which proves an activation effect on titanaugite flotation. In alkaline solution, all these five kinds of ions can adsorb on titanaugite surface, and the floatability of titanaugite will be activation. Based on the above analysis, it can be deduced that in the flotation system using fatty acid as collector, the adsorption of metal ions on mineral surfaces and the stronger reaction ability with collector than active site on mineral surfaces, are the two prerequisites for metal ions show activation effect on mineral flotation.INTRODUCTIONIn flotation pulp, the existence of metal ions is often inevitable. There are two sources for these metal ions: the first part is generated in grinding and flotation process due to the oxidation, reduction, corrosion or dissolution of minerals or grinding medium; the second part is from the flotation water or the addition because of the technology need. The metal ions in the pulp have a considerable influence on mineral flotation. Earlier researches are focus on the activation effect of mineral floatation by metal ions to obtain a higher flotation efficiency, many effective activators were found, such as Cu2+ activated sphalerite, Pb2+ activation wolframite, and Ca2+ activation quartz flotation, these metal ions have become the commonly used activators in industrial production. And many studies attempted to explain the mechanism of how metal ions affect the floatability of minerals. James (James et al, 1972) suggests that metal hydroxide precipitation is the main component leads to activation effect, while the study of Fuerstenau (Fuerstenau, 1976) showed that the metal ion hydroxyl complexes played significant role. In recent years, the reuse of mineral processing wastewater has attracted more attention (Rao et al, 1989; Liu et al, 2013; Wang et al, 2014), as a main component in flotation wastewater, the influence of “unavoidable ions” on flotation process still need in-depth study."

Jan 1, 2018

By B. Orberger, J. M. Milazzo, S. B. Blancher, J. Lützenkirchen, J. L. Dubos

"Industrial dusts are commonly agglomerated using empirical recipes with binders such as bentonite, while Sludges are agglomerated into mixes. Those materials contaminate the products, are expensive and generate significant amounts of slag. Achieving cold dust agglomeration with little or no binder requires understanding the controlling parameters in order to predict and optimize the process behavior. This in turn necessitates comprehensive dust characterization to base predictions on measurable characteristics. In the present work we collected 13 Mn-rich dusts over all the process chain: feed fines, smelting, and refining dusts, as well as ferromanganese alloy dust. This is the first systematic study of dusts along the Mn-processing chain for chemical, physical and mineralogical parameters. X-Ray Diffraction, Qemscan® and laser granulometry analyses show that the mineralogy, Particle Size Distribution (PSD) and morphology evolves from complex heterogenous to simple, homogenous along the process chain: The mineralogy of the primary ore dusts shows various hydroxides, oxides, carbonates, tectosilicates and phyllosilicates. The furnace dusts contain oxides, tectosilicates and carbonates with volatiles, while the refining dusts present only oxides and metal. Finally, the Metal dust is nearly pure metal. Particle morphologies and PSD vary from jagged, irregular particles with broad PSD (>1 mm to <0.3 µm) to smooth and spherical with narrow PSD (100 µm to <0.3 µm). The Metal dust is an exception with angular particles. The Cationic Exchange Capacities (CECs) of all samples range from 0 to 22 meq/100g. Specific surface areas (SSAs) range from <0.1 to 27m²/g, and seem to decrease with from ore feed to Metal dust. This may be due to the disappearance of hydrated and/or sheet-bearing minerals, since a smaller grain size usually implies an increased SSA. The zeta potential varies strongly over the range of the samples tested. However, beside the Gabon ore which has an Isoelectric Point (IEP) ~ 4.1, the other IEP ranges between 2 and 2.5."

Jan 1, 2018

By L. Li

Chemical composition, mineral composition, and iron occurrence state of main mineral are studied, Research of mineral processing technology is carried out according to ore features. The test results indicate, that through staged grinding-staged concentration process, the better separation index is up to 65.54%, iron preparation concentrate grade and 85.66% recovery with the fineness (-200 mesh) 45.88% in the primary grinding ore and the fineness (-200 mesh) 75.50%, in secondary grinding ore in the situation of best magnetic field intensity (roughing 0.2T and cleaning 0.15T).

Sep 1, 2012

By M. Minagawa, G. Granata, C. Tokoro, T. Kato

"In this work, we studied the mechanochemical activation of chalcopyrite by vertically stirred ball milling (VSBM) to enhance the dissolution of copper. By using x-ray diffraction (XRD) and laser diffraction particle size analysis, we investigated the effect of milling and milling conditions on particle size and phase composition of the chalcopyrite concentrate. To elucidate the efficiency of VSBM towards the mechanochemical activation of chalcopyrite, we also conducted leaching experiments in sulfuric acid-ferric sulfate media. Under all investigated milling conditions, the VSBM determined a dramatic decrease of particle size from over 100 µm of P80% up to about 13 µm. Furthermore, the XRD of the ground chalcopyrite specimens highlighted a partial oxidation of the mineral. In leaching, upon grinding by VSBM, the increase of copper extraction ranged from a minimum of +10% to a maximum of +40%, depending on the grinding conditions. In order to elucidate whether the dissolution enhancement was a consequence of the decreased particle size or of an induced mechanochemical reaction, we performed leaching experiments on activated and non-activated chalcopyrite sample having the same particle size. In addition, we determined the activation energy of leaching before and after vertically stirred ball milling. The leaching results on samples with the same particle size highlighted a greater copper extraction and higher dissolution rates upon mechanochemical activation. Whether performing grinding by VSBM or not, the leaching kinetics was found to be controlled by the chemical reaction on the surface of the chalcopyrite particle. By grinding the chalcopyrite concentrate by VSBM, the activation energy of leaching slightly decreased from 66 to 58 kJ/mol. INTRODUCTION Due to the increasing demand of copper, low grade ores and refractory minerals like chalcopyrite are expected to become the main copper source in the next years (Klauber, 2008). As a low-grade sulfide, chalcopyrite shall be processed hydrometallurgically. However, due to the formation of a protective layer of elemental sulfur during the oxidizing leaching, the dissolution of copper is slow and/or incomplete (De Bernardi and Carlesi, 2013). Therefore, the development of new technologies to enhance the extraction of copper from chalcopyrite is highly required."

Jan 1, 2018