Search Documents

By Kal Sastry, Anshuman Prasad

This paper presents a population balance model (PBM) for describing the agglomeration process and select a suitable coalescence kernel that can simultaneously describe nucleation, layering and coalescence mechanisms. The PBM is solved numerically by making use of a size discretization procedure in order to simulate iron ore agglomeration in rotating drums where moist feed is added to preformed seeds. Subsequently, a comparison of computer simulation results with the previously published experimental data is provided. Finally, the paper discusses how the current approach can be further extended to the simulation of industrial iron ore agglomeration circuits operated in closed circuit.

Jan 1, 2003

By Ping Fang, Dezhou Wei, Zichuan Guan, Wengang Liu, Yanbai Shen

A new cationic collector, bis(2-hydroxy-3-chloropropyl) dodecylamine (N23), that can be dissolved in water easily was synthesized successfully. Its flotation performance to quartz was investigated compared with dodecyl amine in hematite reverse flotation system. It was found that N23 showed stronger collecting performance to quartz than dodecyl amine. The maximum recovery of 98% to quartz was obtained at a collector concentration of 43.3 mg/L in the pulp pH range of 6-9. This collector can be used to float quartz from hematite when starch was used as depressant. Optimal separating results with 90.06% iron recovery and 66.3% iron grade to artificially mixed sample were achieved at a collector concentration of 43.3 mg/L and a starch concentration of 23.3 mg/L at neutral pulp pH when hematite and quartz were mixed at a mass ratio of 3:2. The adsorption mechanism of the collector on quartz surface was investigated by infrared spectroscopic analysis and zetapotential measurements, which revealed that electrostatic attraction and hydrogen bonding adsorption occurred between the collector and quartz surface.

Jan 1, 2014

By V. V. Zakopaylo, M. V. Lukyantseva, V. A. Ignatkina, V. A. Bocharov, L. C. Khachatryan, D. M. Altynamanov, A. A. Kayumov, R. H. Sharipov

"This research was aimed to explain the reasons of low floatability of tennantite from refractory pyrite ores of non-ferrous metals and to create a reagent regime for selective increasing a recovery of copper sulfide minerals from arsenic-containing copper pyrite ore. ?opper-zinc ore of the Uzelga deposit has 89% of pyrite, some part as melnikovite; copper is assayed as 3.58% of tennantite and 0.25% of chalcopyrite; there is 2.19% sphalerite. Sulfide minerals are very finely disseminated. Tennantite is genetically related to primary copper sulfides. Graphene was identified on the surface of tennantite by a transmission electron microscopy (TEM) method. The recovery of tennantite was rose up by using the collector M-TF. M-TF is the mixture of diisobutylditiophosphate (DTF) and O-isopropyl-N-methyl (ethyl) (TC) in the certain ratio. M-TF change up a kinetic of copper sulfide flotation in a slightly alkaline medium, but pyrite has slowly floatability at this moment. A depressing effect of thiosulfate ions in a liquid phase of pulp flotation tennantite from pyrite ore has been established. A copper recovery up 14.2% (from 67.7 to 82.0%) into a copper concentrate level off copper grade of 18.65% (butkx) and 18.68% (M-TF) has been increased by the new technology with M-TF compared to a standard technology with butkx. A main copper recovery up to 50 % in an inter-cycle copper concentrate assaying 19-21% Cu in case of using M-TF was gotten. A zinc concentrate with recovery of 50% and a zinc assay of 41.76% by a standard flow sheet with butyl xanthate was obtained. A zinc recovery of 70.3% with a zinc grade of 44.17% by the M-TF technology was achieved.INTRODUCTION The pyrite copper-zinc ores of the Urals region are considered refractory. The distinctive features of these ores include a high content of pyrite (90-95%), the presence of arsenopyrite and arsenical pyrite, and the simultaneous presence of chalcopyrite, bornite, tennantite with the predominance of the latter (Andreasen et al.,2008;.Dobrotsvetov, 2009; Chanturiya et al. 2016). The flotation properties of tennantite differ from those of chalcopyrite (Xumeng Chen, Yongjun Peng, Dee Bradshaw. 2014), which is the reason why a comprehensive study was under taken of the flotation activity of tennantite and a process for its recovery was developed. The proposed agent treatment and flotation process make it possible to produce salable copper and zinc concentrates."

Jan 1, 2018

By Behzad Vaziri Hassas, Firat Karakas, Mehmet Celik, Onur Guven

Since dewatering is a costly process, removal of moisture from relatively fine size lignites is an important industrial problem. As the lignite gets finer, the presence of micropores and relatively low hydrophobic nature of lignite lead to trapping of large quantities of water in the coal matrix. Lignites used in power stations need to be dried to a certain degree of humidity before it is transferred to the combustion chamber. It is generally wise to dewater coal as much as possible by physical means before it is dried. However, dewatering cost in some cases may be prohibitive. Thus, sometimes removal of even little percent moisture may be of great help in such operations. Surfactants have been used to increase the efficiency of coal dewatering. It is crucial to select appropriate type and amount of surfactants in order to get higher efficiency. Since the hydrophobic characteristic of coals increases with increasing the coal rank, dewatering of bituminous and anthracite can be accomplished using low HLB surfactants (Oily), however, these surfactants are not efficient in the case of low rank coals like lignites and brown coals. It is suggested that adsorption of low HLB surfactants on high rank coals is governed by Acid-Base interactions rather than electrostatic and van der Waals forces. Since this characteristic in lignites is not strong enough, low HLB surfactants could not be effectively adsorbed on low rank coals to make surface more hydrophobic. In this paper, a special set-up has been designed to study the effect of high HLB surfactants on dewatering of fine lignite particles. It is shown that high HLB surfactants function more efficiently on low rank coals than low HLB ones.

Jan 1, 2014

In the present work, the influence of coagulant, polymeric flocculant structure type and mode of addition on flocculation performance and dewatering behaviour of plant mineral waste tailings of diverse mineralogy (kaolin, quartz, goethite/hematite feldspar, gibbsite, rutile, and Illite) is investigated. High molecular weight, non-ionic polyacrylamide homopolymer and anionic (acrylate) and cationic (quaternary acrylate) copolymers were used in orthokinetic flocculation of colloidal-ly-stable, aqueous dispersion of negatively charged particles. It is demonstrated that, through prudent selection and mode of addition of polymer structure types, synergistic effect between certain cationic and anionic flocculants can be readily achieved, leading to significantly improved dewaterability of the heterogeneous mineral waste tailings.

Jan 1, 2014

By M. L. Cao

In this study, a montmorillonite organo-intercalation compound (MOIC) was synthesized by using a Na-modified bentonite (NaB) as a matrix and hexadecyltrimethylammonium (HDTMA) bromide as an intercalating reagent under microwave irradiation. The synthesized products were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), organic carbon content measurement, and adsorption density determination. The results show that, at 10% suspension concentration and 10 minutes irradiation in a 130-W microwave oven, the basal spacing d(001) of the synthesized MOIC increases to 2.209 nm from the original 1.218 nm of NaB. The MOIC has much higher adsorptive densities to nitrobenzene and aniline from aqueous solution than the NaB. The adsorption isotherm of nitrobenzene on the MOIC is linear, and the adsorption is mainly the result of nitrobenzene?s preferred partition in MOIC over aqueous solution due to MOIC?s hydrophobicity. The adsorption isotherm of aniline on MOIC follows the Freundlich equation and the increased adsorption is not only the result of aniline?s preferred partition in MOIC over aqueous solution but also that of the MOIC?s surface adsorptions.

Jan 1, 2014

By Z. M. Wang

A large scale a polymetallic mine in north China is a refractory ore containing many useful com-ponents: W, Mo, Cu and Fe. Mineralogical investigation shows that the deposit is a quite complex one due to fine disseminated size and unevenly distribution of valuable, intergroth of sulphide and tungsten minerals, concurrence of scheelite and calcium minerals. Based on ore characteristic, a flowsheet is used by the floatation processing of sulfide minerals superior to scheelite. Bulk sulphide flotation is used in sulphides. Mo and Cu are floated in sequence after sulphides regrinded. Tungsten mineral is floated using combined depressant that is an effective depressant to gangue, and can improve the grade of rough tungsten concentrate. Compound depressant has high effective in removal of collector in gangue and sulphide, and tungsten is activated also. High quality of tungsten concentrate is obtained at satisfactory recovery. The test production obtains Mo concentrate with grade of 48.16%, recovery of 81.43%; W concentrate with grade of 66.47%, recovery of 78.19%; Cu concentrate with grade of 23.14%, recovery of 56.6%; Fe concentrate with grade of 67.33%. The valuable metals are recovered comprehensively and well techno-economic index is obtained. The mine enterprise profit is increased greatly.

Jan 1, 2014

By P. K. Sen, Mrinal K. Ghose

Tailing slurry is usually abrasive and possesses high viscosity. This paper examines the existing iron ore beneficiation process and focuses on some of the key environmental issues related to the disposal of tailings. It identifies that almost 32% of the iron ore extracted ends up as tailings and they are usually disposed in slurry form in tailing ponds. By the year 2000, 27 Mt of iron ore tailings were generated in India, which has become one of the biggest waste handling problems to the industry. Characteristics of the tailings vary widely. So the physical nature of tailings cannot be considered separately in isolation without considering the mill effluent from the beneficiation plant. In the present investigation, studies were carried out in three iron ore mines in India to evaluate the characteristics of tailings from the beneficiation plant. The tailing samples were collected from different locations during a time period of one year and analyzed. The results will be discussed and the characteristics of the tailings have been evaluated. The disposal system of tailings at the three mines was evaluated. The research on the settling characteristics of tailings indicates that the area provided in the existing tailing ponds in India is much more than that of the experimental results. This paper concludes that sedimentation tests are essential to design appropriate tailings pond with respect to size. In the proposed scheme it is suggested that an additional unit process, i.e. sedimentation tank be added to the process before the disposal of tailings to the tailing pond.

Jan 1, 2003

By A. Boulton

Low molecular weight synthetic polymers substituted with hydroxyl, carboxyl or sulfonate functional groups were used to improve the flotation separation of zinc or copper sulfide minerals from iron sulfide gangue minerals in three massive sulfide ores of different mineral composition. These polymers produced significant improvements in zinc or copper grades as a result of a selective depression of iron sulfide minerals. These results are significant considering the differences in ore type, proportion and type of iron sulfide minerals present, and grinding medium used in this study.

Jan 1, 2003

By Mahdi Shevrini, Hamed Haghi

"In this research, the operation of screen classifying in silica processing circuits was investigated and modified by replacement of available trommel screens with teetered bed separator (TBS). In addition the effect of the mentioned replacement and addition of attrition scrubber on quality of final product, impurities removal, recovery and production rate were inspected. Considering screen efficiency problems to achieve certain particle size distribution, hydraulic classifying system was selected instead of trommel screens. Application of suggested plan improved quality and particle size distribution of produced silica significantly. Optimization of size classification in process circuit resulted in increase in production rate up to 21% (from 67% to 81%), silica recovery (from 68.35% up to 83.11%) and relative enhancement in removal of impurities such as Fe2O3 and TiO2. After optimization and stabilization of grinding and size classification section, industrial attrition scrubbing tests were carried out and the best solid percent and retention time were determined i.e. 70% and 6 minutes, respectively. Using sodium carbonate during attrition scrubbing, has major effect on removal of surface coating and staining especially sharp increase in clay removal; therefore 2 kg/t of sodium carbonate can be optimistic point of industrial procedure for this silica processing plant. It should be mentioned that application of attrition scrubbing which is followed by screw classifier for de-sliming were useful for better cumulating of particles in the range of appropriate liberation degree (+106-300µm) and efficient removal of metallic (iron and titanium oxides) and non-metallic (clays and feldspars) impurities."

Jan 1, 2014

By A. N. Zagorodnyaya, T. N. Bukurov, Z. S. Abisheva, A. S. Sharipova

"The paper describes the results of stripping of copper production dusts by leaching with aqueous soda, nitric acid solutions and recovery from solutions resulting in the production of lead sulphate, tribasic lead sulfate (TBLS), ammonium perrhenate, zinc, copper-cadmium cake.The combination of two stripping operations under chosen optimal conditions allows the recovery of 98% rhenium, 82% lead, 92 % copper, and 96% zinc and cadmium each. The major amount of rhenium (~ 80%) is recovered at the carbonization stage, and other metals - at the nitric acid leaching stage.Lead sulfate was precipitated by mixing solutions resulting from carbonization and leaching. Tribasic lead sulfate was produced by dissolving lead sulfate in sodium hydroxide solutions. Rhenium was recovered from mother liquor resulting from lead sulfate precipitation by liquid-liquid extraction and zinc was recovered from raffinates. Trialkylamine (TAA) was used as an extractant for rhenium recovery and di-2- ethylhexylphosphoric acid was used for zinc recovery. Optimal liquid-liquid extraction parameters have been defined allowing the recovery of 96% rhenium in crude ammonium perrhenate and 94% zinc in sulfuric acid solution. Based on the experimental data, the flowchart for dust processing to produce salable products - lead, rhenium, zinc salts has been suggested."

Jan 1, 2003

By S. Z. Shafaei

An experimental investigation has been carried out using a laboratory scale Denver flotation cell. For evaluation of cokeable coal of Alborze Sharghi coal washing plant, the full factorial method was used to statistically design and analyse the experiments. The 2 factorial interaction model were developed for combustible recovery and ash content as response and diesel dosage, conditioning time, feed percent solids and rotor speed as factors. Model validation and residual analysis were con-ducted and results indicated that the fitness, predictability power and residual distributions of models were good. The effect of parameters and interactions were examined and it has been demonstrated that rotor speed, solid percent and interaction between diesel dosage and solid percent were more important terms of all responses. A product with approximately 78% combustible recovery and 10% ash content was obtained at 4000gr/ton diesel fuel oil (high level), 30 sec conditioning time (low level), feed percent solids of 15% (low level) and 800 rpm rotor speed in appropriate condition.

Jan 1, 2014

By Cheng Wei

Fly-ash was used as adsorbent to remove butyl xanthate from aqueous solution in this study. Adsorption kinetics investigation reveals that the adsorption process abides by the Lagergren-second-order Kinetic Model, and fine fly-ash prepared by grinding has a higher second-order adsorption rate as 1.25 g/mg?min and a higher saturated adsorption amount as 10.92mg/g. Four influencing factors as adsorption temperature, solution pH, consumption of fly-ash and adsorption time were investigated. Testing results indicate that butyl xanthate removal rates declines slightly with the temperature increase within the range of 15-50?, increases slightly when pH rises from 7.27 to 8.01 and then declines from 99.65% to 98.25% when pH rises from 8.01 to 11.10. An enhancement of removal rates can be observed by increasing the consumption of the adsorbing agent or prolonging the adsorption time. Thermal desorption was adopted to regenerate the used fly-ash, and test results show that fly-ash possess good regeneration performance and could be used as adsorbent repeatedly with little influence on the adsorption capacity.

Sep 1, 2012

By Xin Tan, Changgen Li

"The floatabiliby of chelate CF-collector for zinc and lead oxide minerals was described. It found that CF-collector possesses a strong collection power for zinc and lead oxide minerals as well as excellent selectivity for the gangue minerals. A new technology of zinc and lead oxide flotation with CF reagent as a collector, lead nitrite as a activator and water glass as modifier was presented. The mechanism of interaction between reagents and minerals was discussed by means of adsorption, zeta potential, nephelometric titration, XPS and infrared spectra was investigated.CF-collector, newly developed by Beijing General Research Institute of Mining and Metallurgy (BGRIMM), is a kind of chelate collector for the flotation of oxide minerals. CF-collector mainly consists of N-nitroso-N-phenylhydroxylamine ammonium salt. The CF-collector was used for the selective flotation of scheelite in the Chinese plants.In this paper, the effects of the dosages of activator Pb(NO3)2 and depressants (sodium hexametaphosphate, polyphosphate, water glass and salified water glass) on the floatabilities of several minerals (cerussite, smithsonite, calcite, dolomite, limonite and quartz) as well as their mixtures were investigated in the presence of the CF-collector. The results show that the CF-collector is the excellent collector for selective flotation of cerussite and smithsonite. Pb(NO3)2 can selectively activate the oxides of lead and zinc resulting in a decrease of the CF-collector dosage. The sodium hexametaphosphate plus the salified water glass are the effective depressants for gangue minerals. Based on the above facts, the “CF process”, namely, used CF reagent as a collector, Pb (NO3) 2 as a activator, and sodium hexametaphosphate plus salified water glass as depressant, has been used for the flotation separation of the lead oxide mixtures or zinc oxide mixtures without disliking and heating. For the feed lead assaying 19.07%, the lead concentrate assaying 49.81% Pb at the recovery 80.69% was obtained after one step flotation. For the feed zinc assaying 12.85%, a zinc concentrate of assaying 29.56% Zn at recovery 83.87% was obtained."

Jan 1, 2003

By Rodney J. Hundermark, Sharif Jahanshahi, Shouyi Sun

"The major platinum producers in South Africa make use of electric furnaces for the melting of platinum group metal (PGM) bearing nickel – copper concentrates. To gain better understanding of the furnace operation, research was conducted at CSIRO Minerals in Melbourne, Australia. One aspect of the research project was the investigation of the factors affecting the electrical conductivity of melter type slags.Electrical conduction in slags can occur through two mechanisms: ionic and electronic. There is good understanding of the ionic mechanism. In slags containing high levels of iron, the dominant mechanism is electronic as a result of charge hopping (electrons or holes) between ferric and ferrous ions. There is limited understanding of the electronic mechanism and one of the aims of the research was to investigate this mechanism further.Experimental work was carried out at 1450 °C on Al2O3–CaO–FeOx–MgO–SiO2 slags similar in composition to the melter slags (typical composition range (wt%): Al2O3: 5, CaO: 5-15, FeOx: 10-30, MgO: 15-25, SiO2: 40-60). The approach was to vary the oxidation state of three different basicity slags and measure the conductivity response. The slags had molar (CaO+MgO)/(Al2O3+SiO2) ratios of 0.43, 0.64 and 0.94 and FeOx contents of up to 40wt%. A twoelectrode technique was employed with a shallow layer of slag contained in a magnesia crucible. The small amount of slag facilitated relatively quick equilibration (up to one hour) with the gas atmosphere. Experiments were typically started in air and sequentially reduced using different ratios of CO and CO2 gases.Conductivity increased with increasing basicity and increased significantly with iron oxide content. Above 20wt% FeOx, electronic conduction was significant and the conductivity varied with the oxidation state of the slag. The typical response of the conductivity to the change in oxidation state was the following: starting in air, as the slags became more reduced, the electrical conductivity increased to a maximum at around pO2 = 10-7 to 10-4 atm and then decreased with further reduction. The value of the pO2 at which the maximum occurred was dependent on the total iron oxide content and basicity of the slag. The magnitude of the conductivity of the slags increased with increasing FeOx content in a range of 20 to 170 S/m for 20 to 40wt% FeOx. For a given FeOx content in the slags, the oxidation state dependence of the conductivity varied with slag basicity. The trend observed was that the maximum in the conductivity occurred at higher oxygen partial pressures for the lower basicity slags."

Jan 1, 2003

By Stefan Mutz, Thomas Pretz, Jörg Julius, Frank Hilbk-Kortenbruck, Aachen, Hartmut Harbeck

"The annual global production of primary aluminium was about 22 million tons in the year 2000. This represents the second largest production rate in the world market after steel. Experts are predicting that the global demand for aluminium will rise in the near future.In contrast to other metals such as copper, the recycling of aluminium is considered relatively difficult. There are two main alloying groups, namely cast and wrought. In the case of aluminium it is important that the constituents within the scrap aluminium to be smelted are clearly identified. Within the secondary remelting process alloying does take place, but a removal of unwanted metal constituents is problematic. Therefore mixed aluminium scrap (not genuine in-house collected material) can only be used to produce cast aluminium. Thus, in other words a down-cycling of wrought (extrusions and rolled) products occurs. However, in spite of these difficulties there is an increasing trend to produce aluminium from secondary scrap (approx. 35% in Germany). Similar trends have been identified in the USA and other industrialised countries. This development is mainly caused by the high energy consumption for the production of aluminium from bauxite. Producing aluminium from scrap is saving about 95 % of the energy in comparison to the processing of primary raw materials.An improvement in sorting technology is necessary to separate wrought and cast alloys of aluminium as the absolute amount of recovery from old scrap is higher than the demand for cast.This contribution presents some alternative methods, utilizing automatic picking technologies, which will be used to separate secondary aluminium in the future. During the recent years, some major progresses have been made in automatic picking technologies for different applications in the processing of primary and secondary materials.For the sorting of aluminium scrap a special additional sensor will be necessary. The best detection will ultimately be based on online elemental analysis of single particles. First investigations in the field of laser based systems for these applications have already been performed several years ago. One of the laser based techniques is the laserinduced breakdown spectrometry (LIBS)."

Jan 1, 2003

By Slobodan B. Vujic

"For the requirements of the mining company “Rudnik-Rudnik”, engaged in undergr-ound exploitation of polymetallic ore and lead, zinc and copper concentrates production, the Department of Computer Application of the Faculty of Mining and Geology, University of Belgrade, designed a computer supported and integrated information-management system. This paper presents a concept of this system covering both monitoring and management of production in ""Rudnik-Rudnik"".The ""Rudnik"" Rudnik, Yugoslavia is a mining company, engaged in underground exploitation of polymetallic ore and production of ore, zinc and copper concentrate as well as other metals such as silver, bismuth and cadmium. This mining company runs stable business activities and undergoes a permanent growth of valuable production volume.The basic characteristics of production-technical system of ""Rudnik"" company are: uniform and up-todate technical-technological solutions: linking of production chain from underground exploitation of ore to flotation, namely final product - concentrate of lead, zinc and copper; complete mechanization of production; relatively low level of computer technics implementation; namely, ununiformed implementation of different application of computer-supported information technologies in production and business activities of the Company.These are the assumptions on the basis of which the management of the Company made a decision, in 1999, to upgrade information-management functions through development and application of modern integrated and computer-supported production-business information-management system (hereinafter: IMS, namely IMS Rudnik). For this purpose the Company requested the Department of Computer Application, Faculty of Mining and Geology, University of Belgrade to make the Project on IMS for their needs."

Jan 1, 2003

By L. Pan

As an air bubble approaches a mineral surface, a thin liquid film (TLF) is formed in between. The excess pressure (p) in the film determines the kinetics of drainage, which is of critical importance in flotation. We have developed a new method of monitoring the kinetics for both stable and unstable wetting films and analyzed the results using the Reynolds lubrication theory. It has been found that initially a TLF is thinned by the Laplace pressure (pcur) due to changes in bubble curvature and subsequently by the disjoining pressure (?) created by the surface forces present in a wetting film. In the present work, we have derived an analytical expression for determining ? from the temporal and spatial profiles of TLFs on mineral surfaces. The results show that ? > 0 in a film formed on a hydrophilic surface and ? < 0 in a film formed on a surface hydrophobized by collector. Thus, the role of collector in flotation is to create a hydrophobic force and hence a negative disjoining present in wetting films. It is also found that smaller bubbles can create higher Laplace pressure, which helps the TLF drain faster.

Sep 1, 2012

By M. R. Robben

Carbonates have gained significant economic importance for the human kind. On one hand over a hundred uses are listed for carbonates. On the other hand, carbonates host base metal deposits. Although the carbonates play a significant part in the development of those deposits, in the mineral processing they consume acid and cause selectivity problems during flotation and leaching. Carbonates also accompany other industrial minerals as waste rock. For all those cases it necessary to find a technique to separate carbonate as early as possible in the processing chain. In this paper, the applicability of near-infrared spectroscopy (NIRS) sorting for the separation of carbonates is discussed. NIRS sorting is a sensor-based sorting technique, in which particles are singularly detected by a sensor and then rejected by an amplified mechanical, hydraulic or pneumatic process. This technique can for example be implemented in the process as a pre-concentration step for coarse particle sizes up to 300 mm. NIRS sorting discriminates among materials based on the difference that exist between their spectral properties in the near-infrared (NIR). Vibrations of molecular bonds in carbonates cause characteristic spectral properties in the NIR, which makes carbonates detectable, possible to identify, distinguish and separate from other rock materials. The spectral properties can also be used to distinguish between different carbonate minerals and mixtures. If the spectral variations are large enough for detection, sorting based on NIRS is possible. Feasibility studies on sensor-based separation of carbonates in the processing of talc, borate, fluorite, marble, zinc-oxides, copper sulphide and iron ore as well as the discrimination of calcite and dolomite mixtures are conducted and indicate the high potential of NIRS sorting in the minerals industry. Keywords: carbonate separation, sensor-based sorting, near infrared spectroscopy, NIRS sorting

Sep 1, 2012

By Mike Daniel, Eric Wang

"Several new large copper and gold concentrators have been built and commissioned around the world in the past five to eight years. The success of the ramp-up from these very large concentrators has varied. CITIC SMCC Process Technology was engaged to assist some of these mines by gaining a better understanding of the factors that influence throughput capacity. As such, site-specific throughput forecast models that are influenced by SAG mill performance were developed. The forecast models are easy to interpret and modify and can greatly assist the mine management to make predictions and informed decisions for a range of site improvements. The models investigate the influence of SAG mill performance with respect to ore competency, derived from SMC Test® via the measured DWi model parameter. In some cases the benefits of blasting and from fine tuning milling operations are already incorporated into the "site-specific" forecast models. The methodology follows rigorous plant data analysis that is analogous to a "Mine-to-Mill®" optimisation project. The CITIC-SMCC model validation includes extensive data collection, which includes drill core analysis, ore characterisation and comprehensive comminution circuit operational data to assess the limitations within the comminution circuit within the operating mine. The results and models may be used to define the operating base lines of the processing areas and identify improvement opportunities upstream and downstream of the comminution circuit. The predictive capability of the models use logged production data and has enabled the user to differentiate between alternative circuit configuration options and identify optimum operating conditions. This approach minimises the ongoing requirement for costly plant surveys. The improvement strategy for each site, included the ongoing measurement of grindability, rock strength and via the Bond and SMC Test® respectively. Some commentary as to what other practitioners do with input data and their models is also presented as this highlights some of their shortcomings relative to the CITIC-SMCC methods."

Jan 1, 2014