Search Documents

By J. Yianatos, C. Matamoros, F. Díaz

The non-selective entrainment of fine solids in flotation equipment has a detrimental effect on the concentrate grade. Reduction of solids entrainment (upgrading) is typically related with a loss in recovery of valuable minerals. For improving the froth transport characteristics and flotation cells design, a better understanding and quantification of the actual solids drainage and entrainment processes are required. In this work, the study of solids transport in the froth of a two-dimensional flotation cell was performed. The prototype cell represents a radial section of an industrial flotation cell (130m3) and was operated at steady state. Experimental tests consisted of adding a small amount of radioactive solid tracer (0.3g) near the top-of-froth or near the bottom of froth (close to the interface). The solid was selected as a non-floatable mineral (gangue) in order to evaluate both the solid entrainment into the concentrate as well as the solid drainage into the collection zone. Solid tracer consisted of fine or coarse gangue particles, P80 of 35 and 120 µm, respectively. Twelve collimated sensors located along the froth and collection zones allowed the evaluation of the solid transport in the froth, and the solid drainage from the froth to the collection zone, after tracer addition at different distances from the discharge lip. Results showed that longer distances to the froth discharge lip, as well as higher particle sizes, promotes higher solid drainage from the froth to the pulp zone, while decreasing the solids entrainment into the concentrate. The same result was observed for the solid located near the top-of-froth as well as near the bottom of froth. This information was complemented by the froth surface velocity measurements, using the Visiofroth system, showing a good agreement between the froth bubbles velocity and the solid transport velocity, measured near the discharge lip.

Jan 1, 2018

By Lei Pan, Roe-Hoan Yoon

"Direct force measurement for bubble-particle interaction has been difficult due to bubble deformation, which makes it difficult to know the separation distances between the two macroscopic surfaces. In the present work, we have developed a method of monitoring the deformation accurately, while directly measuring the interaction forces. In effect, we can ‘see’ bubbles interacting with mineral surfaces under different hydrodynamic and chemical conditions and determine both the hydrodynamic and surface forces involved. In the present work, a high-speed camera has been used to record the optical interference fringes of a thin liquid film (TLF) of water formed on a mineral surface. The recorded fringes are then used to reconstruct the spatiotemporal profiles, from which one can determine the hydrodynamic pressure using the Reynolds lubrications theory. From the forces directly measured in the present work and the hydrodynamic pressures obtained from the fringes, we have determined the disjoining pressure. The results show that air bubbles interacting with hydrophilic surfaces form stable TLFs with zero contact angles. The TLF formed on a hydrophobic surface thins fast, form a ‘pimpled’ film, and ruptures to form a finite contact angle. The new information obtained in the present work may be useful to better understand the role of hydrodynamic and surface forces affecting bubble-particle interactions."

Jan 1, 2014

By Christopher M. Rule, Martyn P. Hay

"A methodology was developed in the mid-1980’s to predict plant performance from standard laboratory flotation tests. The methodology incorporates a flotation simulation program “SUPASIM” which translates flotation performance from bench-scale tests to full-scale plant. The technique is based on a simple, empirical kinetics model, and is tailored for use by the practical metallurgist. Kelsall’s unmodified equation incorporating two rate terms describing slow and fast floating components is used as the basis of the method. The flotation behaviour of an ore is described by a set of numbers, which can be compared in the evaluation of ore types, mineralogy and operating conditions. In so doing a precise relationship is developed between metallurgical performance in terms of grade and recovery and flotation kinetics.To date the performance of more than 20 flotation plants has been predicted, encompassing copper, lead, zinc, nickel, phosphate, pyrite, graphite, cassiterite, platinum and various slags. In three cases, plants have treated more than one type of ore. The method has successfully been used to predict and design four flotation plants using data generated from bench-scale laboratory flotation testwork. All have since been commissioned, and have performed as predicted. In the last year alone it has been used to drive flowsheet development for at least seven new plants in South Africa and the Americas. It is also being used to assist in the optimisation of existing operating plants."

Jan 1, 2003

By Patrick A. Turner, Timothy J. Olson, Abraham J. Schutte, Roman van Ommen

"The use of classifying devices in grinding circuits dates back to the early 1900’s when classifiers were installed to close ball mills. The search for ways to further improve grinding circuits led to the use of hydrocyclones in place of mechanical classifiers in South Africa in the early 1950’s. Today Hydrocyclones are considered as the best classifying devices to close grinding circuits. After 50 years of development the hydrocyclone has changed significantly when compared to the designs of the early days, but the focus to circuit optimization must be expanded to an understanding of the integral system consisting of mill, cyclone feed pump and cyclone.The key to good cyclone circuit design and operation in primary grinding circuits will be discussed including individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration.Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. “The importance of constant cyclone feed conditions is unquestioned today. The challenge of Cyclone sizing is a large number of not fully known variables prior to startup. The most significant unknown variable is slurry viscosity. Because of this, engineers often specify a conservative cyclone system that produces a finer than required separation. However, this approach often leads to higher circulating loads and a higher overflow density in order to produce the required separation. The higher cyclone overflow density results in a less efficient cyclone separation. The average concentrator can pick up 2-4% finer overall grind by having a more aggressive cyclone operation.”"

Jan 1, 2003

Considerable attention has been, and is being, given to the physics of water-films associated with bubble interactions at surfaces. In contrast, little information on the chemistry of such films has been reported. This communication reports a method using sum frequency vibrational spectroscopy (SFVS) to describe hydrogen bonding of interfacial water molecules in water films created with bubbles at hydrophilic and hydrophobic surfaces. The SFVS spectra of water films at hydrophilic silica surfaces differ significantly from the spectra of water at a hydrophobic silica surface. The SFVS spectra indicate that a very ordered water structure exists in water films at the hydrophilic silica surface during contact with a bubble and that the extent of hydrogen bonding increases with an increase in contact pressure. Such structural considerations as well as repulsive electrostatic and Van der Waals forces account for film stability for a bubble at the hydrophilic silica surface. In contrast, the SFVS spectra of water at a hydrophobic silica surface show a lack of hydrogen bonding and are characterized by a distinct absorption at about 3700 cm-1 similar to the spectrum of the air/water interface. These results suggest the presence of a water void, or water exclusion zone, at the hydrophobic surface, as supported by X-ray reflectivity measurements reported in the literature, by atomic force microscopy, and by the results from molecular dynamics simulations. Of course the water film at the hydrophobic surface is unstable with film thinning and rupture upon bubble contact. Under these circumstances it is shown that an attractive Van der Waals force between the bubble and the hydrophobic surface can be expected when the water exclusion zone is taken into consideration. As the thickness of the water exclusion zone increases to a thickness corresponding to the size of nano bubbles, the calculated attractive Van der Waals force increases. This analysis may help to explain the so-called ?short range? and ?long range? hydrophobic forces. Keywords: SFVS spectra, hydrophilic silica surface, hydrophobic silica surface

Sep 1, 2012

By Ljudmil S. Grigorov, Eric Forssberg, Hanumantha Rao Kota, Robert J. Pugh, Lidia B. Alexandrova

"The effects of mixed collectors on some physicochemical parameters (thin film lifetime, kinetics of expansion of the three-phase contact, equilibrium three-phase contact angle and surface tension) involved in the elementary act of flotation were investigated experimentally.We have used the microscopic thin balance developed by Scheludko et al (1970) to study the stability and interactions within the thin film between the silica surface and air bubble with (i) a long chain C10 amine and (ii) a cationic/anionic surfactant systems consisting of mixtures of a long straight C10 chain amine with long straight chain C8, C10 and C12 sulfonates at 1:1 molar ratio. The experiments were performed at a range of concentrations at pH 6.5. The equilibrium contact angle was measured with a microscope technique using the modified Mingins-Sheludko method (Mingins and Scheludko, 1979). The surface tension was measured by the method of Wilhelmy (Adamson, 1960). It was found that the mixed surfactants caused lower contact angles, lower rates of the thin film rupture and longer film lifetime, compared to the pure amine system."

Jan 1, 2003

By Dingwu Feng, Jannie S. J. van Devente

"The effect of ultrasonication on reactions at solid/liquid interfaces was investigated in two slurry systems, i.e. gold cyanidation and geopolymerisation. The kinetics of gold extraction were significantly enhanced and the cyanide consumption was reduced in the cyanidation of a pyrite concentrate using ultrasonication, probably due to the prevention of leaching passivation, the improvement of the dissolution of the gold host sulphides and the oxidation of soluble sulphides to sulphate. The effectiveness for ultrasonication was improved with the injection of oxygen and the addition of dithiophosphate through enhancing the formation of the oxidation radicals and selectively inducing cavitation bubbles directly at the sulphide interfaces. Ultrasonically enhanced cyanidation could render currently uneconomic deposits viable for extraction by improved cavitation efficiency with the aid of surfactants.Ultrasonication increased the compressive strength of the formed geopolymers through accelerating the dissolution of the Al-Si materials, strengthening the bonds at the solid particle/gel phase interfaces, enhancing the polycondensation process and improving the formation of semi-crystalline to crystalline phases. The use of power ultrasound will yield high-performance geopolymer materials."

Jan 1, 2003

By Vladimir Vigdergauz

"Electrochemical studies of metal sulfides in connection with their floatability are discussed. According Frumkin, sorption of electroneutral organic substances has a maximum near the potential of zero charge. This idea initiated attempts of application of electrochemical methods for the controlling of organic collector sorption and mineral flotation. The lecture reviews results of electrochemical studies of the processes taking place during sulfide flotation: redox-state of mineral surfaces and xanthate solutions, xanthate sorption and hydrophobic layer composition, surface wettability and flotation recovery of sulfide minerals. Redox-transitions of minerals, transport of ions and charging of mineral surfaces, electroreduction of dissolved oxygen and accompanying processes of oxidation of minerals and reagents-collectors, - all these matters became the subjects of detailed research. Cyclic voltammetry, rotating disk electrodes, spectro-electrochemical techniques and other modern experimental methods now routinely accompany studies of mineral processing. Relatively new electroanalytical techniques like the voltammetry of mineral particles immobilised on electrodes using polymeric binders have become extremely useful for studying weakly conductive minerals and dispersed flotation products. Full discussion of electrochemical studies of metal sulfides in relation to mineral processing must include bioelectrochemistry and electrocatalysis which open exceptional possibilities for selective leaching of gold and non-ferrous metals. At this time, the paper focuses on the sulfide flotation as a potential-dependent process; the problem of oxygen and its influence on the sulfide flotation; the electrochemical aspects of xanthate oxidation and sorption; theory of suspended electrodes as applied to the mineral slurries and experimental study of the effect of electrochemical pretreatment of flotation pulps."

Jan 1, 2014

By Rogerio de Oliveira Baldoino

The sedimentary phosphate deposit of Bayovar is located in a very dry area of Peru (desert of Sechura) which is close to the Pacific coast. It consists of seven superposed layers (beds) which call for different strategy of concentration. The ore is composed predominantly by apatite (84% in weight basis) plus silicates (16%). In order to treat the ore from beds 1-5, a suitable standard mineral processing circuit (composed of scrubbing, screening, attrition and desliming) started its operation in 2010, yielding 3.9 Mt/y of concentrate assaying 30% of P2O5. To concentrate phosphate from beds 6-7, however, it is necessary to carry out further cationic reverse flotation of silicates, at neutral pH, to yield a concentrate, which meets market specification. The new process was developed in laboratory scale by a collaborative program conducted between Vale S.A. and the University of Sao Paulo-Brazil. A pilot plant has currently been running in order to confirm the very good results yielded in laboratory scale. The successful accomplishment of flotation in the current beneficiation flow sheet will enable a capacity expansion of 1.9 Mt/y of concentrate assaying 30% of P2O5. As water resources are very limited at Bayovar region, all the steps of concentration, including flotation, must be performed with seawater, which must be continuously recycled. This work addresses some relevant topics related to the use of seawater in the reverse cationic flotation of silicates: influence of temperature, water quality (ageing and chemical composition) and collector type (ether amine versus condensate). The results indicate that condensate amine works better than ether amine. If flotation is conducted with the former collector, the separation process is able to tolerate changes in temperature (25-40oC) and water quality caused by either evaporation or ageing. Keywords: phosphate, flotation, seawater, temperature, ageing, concentration, salt

Sep 1, 2012

By F. Karakas

In this investigation, one of the most energy consuming stage of the cement manufacturing process, grinding stage, was studied. The aim of the study is to reduce the energy consumption. Optimum operating parameters were determined. Experimental studies were performed at three differ-ent stages. Grinding of limestone, clay and marl which are the main components of the cement, to approximately below 90 microns, was the first stage of the cement grinding. At this stage, effect of feed size and ball charge were investigated. At the second stage, the Bond work index of clinker and additives (slag, trass, limestone and gypsum) was found separately. After forming composite cement with clinker and additives, the Bond work index of this mixture was also determined, thus the results of separate grinding and grinding of mixture were compared. The Bond work index of mixture was found as 13.59 kWh/t, while the arithmetic mean of the Bond work index values of components was 14.90 kWh/t. Finally, clinker and additives (slag, trass, limestone and gypsum) were ground under the same conditions. At this stage, laboratory type of ball mill was used in order to understand grinding characteristics of the cement components. As a result of the experiments, it was found that energy consumption for the grinding will be lowered if the mills with 38 % ~ 40 % ball charge are used in the cement grinding. Moreover, grinding with mixture of clinker and additives gave better results than separate grinding of these components in terms of energy consumption.

Jan 1, 2014

By Jia Ma, Lu-De Qiang, Zhi-Chao Liu, Chun-Feng Li, Guang Li, Bao-Bin Tang

"At present, research on the surface chemical properties of uranium minerals is very scanty, which restricts the research progress of uranium ore flotation process research. The research aimed at exploring the surface characteristics of two common uranium minerals and providing basis for flotation process to enrich uranium minerals in ore. This paper selected pitchblende and uraninite as the object of study, which are widely distributed in uranium deposits. We chose out the pure minerals of pitchblende and uraninite from different ores collected from different uranium deposits. By means of Zeta potential test and X-ray photoelectron spectroscopy (XPS) test, a preliminary study on surface characteristics of the pure minerals of pitchblende and uraninite was conducted. And the significance of the change of Zeta potential, the elements composition and valence state on the minerals surface for flotation was discussed. The research shows that, the Zeta potentials of pitchblende and uraninite in pure water are negative mainly when the pH value varies from 2 to 11, which maybe a result of the difference of ionization capacity between two kinds of oxy-compounds on the surface of minerals. On the surface of pitchblende and uraninite, the metal elements are mainly U, Th and Pb. U is mainly in the form of UO2, Th is mainly in the form of ThO2, and Pb is mainly in the form of Pb and PbO. Based on the surface characteristics of pitchblende and uraninite, we can select process and reagents appropriately in uranium ore flotation.INTRODUCTION Globally, the major challenges associated with exploitation of low grade ores are about finding economically feasible processes for reducing the mass of gangue minerals (Filippov et al., 2012). Among the beneficiation technologies of low grade uranium ores with complex minerals assemblage, flotation is the common process which is used to reduce production cost and eliminate the acid-consuming minerals (Li et al., 2016; Liu et al., 2015)."

Jan 1, 2018

By S. J. Ma

With the very effective depressant and collector developed by China Bluestar Lehigh Engineering Corp (hereinafter referred to as LEHIGH), satisfied results are obtained from laboratorial beneficiation tests on phosphate samples from Karatau, Republic of Kazakhstan by the direct flotation process. In this paper the effect of single factors on performance of flotation is studied and their applicable ranges are proposed. The final test results are described as follows: As the feed contains 23.20 % P2O5, and 3.96% MgO, a phosphate concentrate assaying 29.77%P2O5 and 1.54% MgO is produced, and the P2O5 recovery in concentrate is 88.28%. The beneficiation tests make it possible to simplify existing technology with fine grinding-desliming, followed by reverse & direct flotation system and consequently improve the concentrate grade and recovery for the future beneficiation plant

Jan 1, 2014

By S. N. Titkov

Flotation of halite?new, recently begun to be developed method of processing water-soluble minerals. In the paper the results of studies of the new directions of the application of halite flotation are represented. Studies on the flotation separation of halite and sylvite in the salt solutions of different composition, showed the possibility of the halite flotation realization not only in the carnallite brine (content of salts: MgCl2 25.5% ~ 26.0 %, chlorides of potassium and sodium 5.5% ~ 6.0%), but in the sylvinite brine, which contains 10.5% ~ 10.8% KCl and 20.5% ~ 21% NaCl. On the basis obtained results are carried out experiences on the halite flotation from samples of the converted products of sylvinite ores by flotation method and by the method of the electrostatic separation. It is shown that in all cases it is possible to accomplish effective and selective recovery of halite. The halite recovery into the foam product of flotation makes 80% ~ 90% with an increase in the content of KCl in the cell product of flotation in comparison with a composition of flotation feed: - from the product after the electrostatic separation of ore ? from 76% KCl to 95% ~ 97% KCl; - from the small fraction of ore (- 0.25 + 0 mm) ? from 30% KCl to 60% ~ 64% KCl; - from middlings (intermediate products) of sylvite flotation from 16% ~ 31% KCl to 45% ~ 80% KCl. An increase in the molecular weight of alkylmorpholines increases the selectivity of the flotation separation of halite and sylvite. Halite recovery from small size fraction of ore or/and middling of sylvite flotation with the sub-sequent joint filtration halite product and tails of sylvite flotation allows to reduce considerably expenses for manufacture potash chloride from Pilot-industrial tests for the first time confirmed the possibility of the effective halite flotation in the saturated solutions of chlorides of potassium and sodium (sylvinite brine).

Jan 1, 2014

By J. Yianatos

The cleaning circuit operation and its effect on the plant metallurgical performance, was characterized at Los Pelambres concentrator, Chile. Experimental data from columns, scavenger and regrinding stages was evaluated. Each stage was characterized by size fractions, and the interaction between stages (columns, scavenger, regrinding) as well as the effect that circulating loads had. The approach for describing the flotation equipment operation (cells and columns) considered the collection and froth zones separately. This methodology allows for the identification of the impact that particle size distribution has on the actual collection and froth transport processes, independently. In this way the effect of regrinding on flotation recovery and grade can be related to the corresponding operating variables, e.g. pulp flowrate, air flowrate, pulp level and pulp density, among others. The effect of gangue entrainment was considered using an empirical dimensionless correlation. The interaction between the circulating load and the overall performance of cleaning circuit was evaluated. The circulating load was defined as the ratio between the solid flowrate of scavenger concentrate over rougher concentrate. It was found that the overall cleaning flotation circuit (column-scavenger) can operate at a relatively high and constant recovery for a wide range of mineral treatment. This is possible when the scavenger has the capacity for compensating the decrease in column recovery at larger circulating loads. Under the condition of high overall cleaning recovery, the rougher stage closely represents the plant recovery. However, at large mineral treatment conditions, the design characteristics (e.g. concentrate transport channel capacity and transfer boxes) as well as instrumentation, control facilities and operation, became bottle-necked. A simulator was developed using empirical models for each stage (column, scavenger and regrinding) in order to evaluate proper operational strategies for cleaning flotation circuits Keywords: flotation, cleaning, regrinding, Vertimill, simulation.

Sep 1, 2012

By Avinash Tripathi

It is now well known that the size distribution of the particulate solid has a significant effect on the breakage behavior of particles in the wet as well as dry modes of ball milling operation. In the context of the size discretized batch grinding kinetic model, grinding behavior of particles is characterized by the breakage rate parameters, k, and breakage distribution parameters, B. Understanding the nature of variation of these two sets of parameters with particle size distribution is important for simulation and control of operation of production mills. However, so far it has not been possible to track the variation of both the set of parameters with grinding time simultaneously. In this paper an attempt has been made in this direction by using a modified functional form approach with time dependent constants. Keywords: dry and wet ball milling, breakage rate and distribution parameters, effect of particle size distribution

Sep 1, 2012

By Barbara Peszko, Tadeusz Tumidajski

"Various methods are used to identify the grain composition of fine-grained materials because so far the best notion of the grain size has not found and there is no single method to define grain size. In practice the most important are the following grain sizes: sieve diameter dt, effective diameter de, substitute diameter d2 and statistical diameter dst. The mentioned sizes are connected with the methods of analyses. Methods are correct but measure of different diameters of grain and their results are different.The most important methods of granulometric composition analyses are the following: the sieve analysis, the sedimentation method and the conductometric (Coulter-Counter) methods. In each of these methods various physical features connected with the grain size are measured.Sizes of grains defined by different formulas or measurement methods are associated mutually by dependencies, which are results of differences in their determination or calculation ways.In order to determine principles of results comparison the classification analysis results on linearly or non-linearly connected was made. Analyses which results demonstrate the same type of grain size distribution are treated as linearly connected. It is based on the general formulae which determines the probability density function of random variable which is the function of another random variable having the known density function.In order to show the difference in the grain composition of the same material qualified by different methods, three methods of investigations were distinguished. They are: the sieve analysis performed on precise sieves, the sedimentation analysis performed by means of a sedimentation balance “Sartorius” and the microscopic analysis performed after preparing a microscopic slide where the grain size was measured by the Martin’s method.The materials selected for the analysis were quartzite and glass, which are the material of high purity.The obtained results of mentioned above three types of analyses were approximated by distribution function of four distributions: Weibull, log-normal, cut Weibull and Gaudin-Schuhman."

Jan 1, 2003

By S. Leroy

Grinding is the most energy consuming step in mineral processing, however, it is still poorly understood and its efficiency is difficult to monitor. Mill performances are traditionally measured at the mill discharge, on the basis of a mass percentage passing a certain sieve. This approach does not reflect what happens to the fines through milling. On another hand, if many macroscopic parameters, such as the percent solids of the pulp, its viscosity, or its mean residence time in the mill are known to be related to grinding efficiency, the link between these parameters and particle size distribution (PSD) is still unclear. Here, a methodology is established to understand the effect of ball mill operating conditions on particle size and shape distribution in the grinding process. The study focuses on the particular case of an Upper Group 2 (UG-2) platinum ore concentrator. Due to the very low grade of sulphide and PGM (Platinum group metals) in UG-2, grinding mechanisms are entirely control by gangue minerals. These two minerals have contrasted properties and PGM content and these properties immediately affect the entire recovery process. So, the grinding of both gangue minerals is studied on a size by size basis. At particle scale, three parameters are addressed: particle size, particle composition and particle shape. The specific behavior of chromite and silicate grains is demonstrated. As a conclusion, this study gives some clues to operate ball mills in a more efficient manner regarding chromite issue in the processing of UG-2. Keywords: ball milling control, UG-2, chromite, fine particle, particle shape, segregation

Sep 1, 2012

By T. Damyanov

Spherical grinding media (balls) are the most widely used media for comminution of ores by grinding. A modelling simulation study of the behavior of two grinding media in the grinding process was conducted to determine the possible advantages of the new shape milling bodies called tetraballpebs. Tetraballpebs are in the shape of tetrahedrons with spherical convex walls. A three dimensional CAD model of the mill drum with a diameter of 1200 mm was used. A continuous operating mode was simulated in terms of the 3D contact elements of the model (milling bodies and mill drum). Simulation tests were carried out in a typical grinding mode and at a typical rotational speed of the drum mill (75 per cent of the critical speed in cataracting mode). Studies carried out with both grinding media include equal number of milling bodies with the same weight and volume. Having thus ensured a uniform mass of the grinding media and same number of milling bodies, and constant other conditions and process parameters, conclusions can be drawn about the influence of the shape of the milling bodies on the grinding process. A kinematic analysis of the system using CAE (computer-aided engineering) model parameterization was conducted. The controlled parameters are: ? Power draw; ? Kinetic energy of each milling body; ? Motion of milling bodies inside the drum Keywords: grinding, grinding simulation, balls, tetraballpebs, DEM, CAD-CAE

Sep 1, 2012

By Wenqing Qin, Yunfan Wang, Ximei Luo, Fen Jiao

In order to investigate the effect of nanobubbles on adsorption of surfactant on mineral surface, the nanobubbles on the surface of calcite with -37µm fraction in the sodium oleate system were controlled by pressurization and decompression to mixing vessel. Subsequently, the adsorption amount of sodium oleate on the surface of calcite were detected by ultraviolet spectrum at different stirring times and different pressures. At the same time, the nanobubbles on the calcite surface were imaged with atomic force microscopy (AFM). In addition, a homemade vacuum Hallimond tube device was used for the flotation of single mineral, and the grade and recovery of minerals in concentrate was used to determine the influence of the nanobubbles on flotation. The experimental results showed that a large number of nanobubbles were found on the calcite surface by AFM under the dissolved oxygen difference (DOD) condition of -4 mg/L. And a large difference in adsorption capacity of sodium oleate on the surface of calcite was observed under different air pressure conditions. It indicated that the ambient pressure had a certain effect on the adsorption of sodium oleate on the calcite surface, and this effect did not depend on the constant low pressure or constant normal pressure, but depended on the changing process of pressure. The single mineral flotation experiment results indicated the recovery of calcite under decompression condition (formation condition of nanobubbles) was 1.5-2 times that under constant normal pressure, and the flotation time is much shorter. Moreover, the recovery under constant normal pressure was greatly influenced by flotation time. In this paper, only one aspect of the effect of nanobubbles on mineral flotation was preliminarily explored. It was confirmed that after vacuum-pumping, the adsorption of sodium oleate on calcite surface could be increased, the flotation time also was greatly reduced and the recovery of calcite was increased.

Jan 1, 2018

By L. J. Li, Q. Zhang, Z. H. Liu, Q. L. Chen

Phosphogypsum (PG) is an industrial waste from the production of phosphate fertilizer. The utilization of PG is restricted by its containing impurities, and the pretreatment is crucial to eliminating these impurities. The purpose of the research is to recycle pretreatment PG as raw material for preparation of a-calcium sulfate hemihydrate (a-HH) by salt solution method. The effect of pretreatment technologies of lime neutralization and washing on dehydration rate, phase composition and morphology evolution of a-HH were investigated by crystal water content analysis, XRD and SEM. Furthermore, the change of pH in the reaction process was also discussed in detail. The results show that the dehydration rate of conversion PG to a-HH increases and the corresponding induction period, crystal growth period and total time decrease with an increase in CaO dosage from 0.2% to 0.6%. In the presence of 0.4% CaO or 0.6% CaO, the a-HH presents a long hexagon-prism-shaped crystal with a purity of 94%, and the end face of a-HH presents polyhedron. The system pH sharply decreases with the reaction time under different CaO dosage, and the pH variation from the initial alkalinity to acidity. The main reason is that as the co-crystallized phosphorus dissolved and released HPO42-, and with the pH decreasing to 4-5, HPO42- transformed into H2PO4-. The dehydration rate of washing PG is lower than that of original PG. Compared with the original PG, a-HH with the larger width and smaller aspect ratio can be achieved from the pretreatment PG subjected to lime neutralization and washing, meanwhile the crystal surface is more smooth.

Jan 1, 2018