Search Documents

By E. N. Levchenko, K. V. Bulatov, G. I. Gazaleeva

"The article highlights the new procedure of choosing special methods of disintegration for very complicated rare ores. Especially, there is a complex approach to criteria of comparing different types of crashing machines. Criteria are as follows: degree of crashing, degree of grinding, degree of slime creation and the new creations criteria for selection. The procedure is tested on tantalium and zelestinium ore. A new methods was shown the preference impact crashing machine MD-7 for zelestinium ore. In product of crashing 0,050 mm size are 9.4 %, 0,005 mm size – 2.5 %.This is gut result, and show the best indexes of slime creation. The check of the proposed new methods was done when comparing the crushing of tantalium ores of the Otboynoe deposit in cone inertial and centrifugal impact crushers and roller press. A research was conducted different crashing machines under laboratory and semi-industrial conditions. Different operation modes of crushers were also checked. The comparison of the crushing selectivity criterion and degree of crashing showed that the centrifugal impact crusher (CC) and roller press (RP) has the lower indexes than the cone inertial crusher (CIC). Degrees of crashing for different crashing machines are:centrifugal impact crusher – 10.1;roller press – 10.8;cone inertial crusher – 14.2. The crusher CC the selection criterion is 0,632 units, RP – 0.730, where as for the crusher CIC – 0.848 units. The best crushing mode for the crusher CIC-300? is as follows: turning angle of debalance is 0°, peripheral speed of a cone rotation – 1420 r.p.m, specific energy consumption- 4.99 kW*t/t. Crusher CIC-300? is the best for tantalium ores of the Otboynoe deposit. The new methodic are verification.INTRODUCTION Rare metal concentration circuits are complex, energy-intensive, and costly. The reasons for this include the multimetal nature of the rare metal ores, their volatile material composition and low grade. That is why careful selection of ore preparation circuits is of great importance for minimizing the energy inputs and maximizing the liberation of the valuable minerals. Recent research (Khopunov, 2011, Gazaleeva, 2015) has demonstrated that the most efficient comminution processes available to the mineral processing industry are selective disintegration, crushing and grinding, allowing to liberate the mineral particles along the cleavage in the comminution process. These methods are indispensable for the processing of finely disseminated refractory ores prone to slime formation. Many rare metal ores found in Russia are of this type."

Jan 1, 2018

By Graeme Jameson

"In current flotation circuits it is customary to grind the whole of the mill feed to an initial size, which is determined by the liberation characteristics of the ore, and the ability of the flotation machines to float the fully liberated particles. Usually, the product of the primary mill will be ground further in a ball mill, to improve the liberation of the values and hence the product grade, before passing to rougher flotation cells. The final grind size is ore-dependent, and is a balance of factors including the relation between surface liberation and grind size, the grain size of the valuable particles within the host rock, and the feed grade. The P80 for the feed to flotation may be as high as 300 µm for free-milling copper ores, and as low as 53 µm for finely disseminated complex ores. The grinding of the feed ore requires considerable input of energy. The rate of replacement of wear components such as mill liners and media, is proportional to the energy input. The costs of these two factors - energy and wear - are usually comparable and together they form the major part of the running costs of a concentrator, and indeed, of the whole mining operation. The energy required increases as the final grind size decreases. This talk will focus on the reduction of milling costs that could be achieved, using a fluidized bed flotation technology that can give high recoveries at coarse particle sizes. A number of different circuit designs will be presented, using the new technology. Calculations show that reductions in the running costs of a mine and associated concentrator of the order of ten to twenty percent could be achieved."

Jan 1, 2014

By Tim Suljada, Mary Stewart, Jim G. Petrie, Damien Giurco

"The minerals industry is being challenged to reduce the amount of virgin ore that is mined, and to replace this material through the recycling of used commodity items and scrap, or by the reprocessing of waste materials. It is argued here that the existing technology base of minerals processing and refining offers real potential for handling these secondary resources. The challenge is to develop tools by which the most preferable recycling routes (both economically and environmentally) can be identified from a list of feasible alternatives, taking into account any operational constraints of these technologies.This paper describes an heuristic approach to developing the family of all technically feasible flowsheets to address this challenge, from which a preferred option may be selected according to a set of decision criteria (economic and environmental). Our approach uses conventional flowsheeting techniques of selecting flow variables and splitter functions, supported by design performance information for each unit operation. This set of design decision variables is augmented by knowledge of the suitability of a particular waste or scrap stream for a given unit operation within a flowsheet. We achieve this by comparing the composition of the scrap stream with the range of mineral streams for which the unit operation was designed initially. This is inspired by the “overlap” approach proposed by Legarth, where an “overlap” of 1 would suggest that there is high degree of compatibility between a given secondary resource stream and a primary mineral stream as inputs to a specific technology. The “overlap” concept has been extended to include information about the physical characteristics of secondary resource streams, as well as information relating to synergistic / antagonistic influences of minor elements present in the waste stream. A flowsheet which delivers a product of acceptable quality from a given secondary resource material is built up from a progression of unit technologies. The exercise is repeated to generate the family of all feasible flowsheets from combinations of acceptable unit technologies."

Jan 1, 2003

By Yuri L. Nikolaev

The treatment of placer gold with fine gold, associated with gold-bearing sulfide minerals, heavy minerals and oxidized minerals such as manganowolframite (gubnerite) is not an easy task. In this case, this complex material cannot be treated using physical separation methods such as deep concentration and finishing, magnetic separation and solvent extraction. This technology is usually employed in gold washings finishing plant. The easiest way to recover precious metals in the form of an easy-to-sample saleable product is metallurgical treatment. This paper describes the application of pyrometallurgical processes with oxidative roasting, re-cleaning of cinders (if required) and ore-thermal smelting for producing gold bullion. Hydrometallurgical treatment of slags as an additional operation is recommended in order to maximize recovery of valuable metals. After this treatment, a barren leaching cake rich in PGM can be sold in the market. PGM can be collected as gold-silver alloy during smelting which allows the phase formation of polymetallic matte due to specific composition of fluxes. The PGM are then in the form of saleable gold bullions in the refinery.

Sep 1, 2012

By Vitaly Kretov, Valery Golikov, Vladimir Ryaboy, Elena Shepeta

"The aim of the study was to develop and implement more efficient dialkyldithiophosphate collectors. A hypothesis has been formulated on the action of dialkyldithiophosphates in the flotation of sulphide ores based on the assessment of their complexing properties and surface activity at the liquid-gas border. Dialkyldithiophosphates form weaker complexes with cations of heavy metals compared to xanthates, and are characterized by a large difference in the strength of their complexes with heavy metal cations. It provides higher selectivity of dialkyldithiophosphates in the separation of non-ferrous metal sulphides and iron sulphides from them. To make a quality assessment of the impact of surface activity of the synthesized collectors on their selectivity of action and collecting power, an assessment of the surface tension of their aqueous solutions has been performed using the stalagmometer method. It is well known that a stronger collector is characterized by a greater surface activity, in contrast to a more selective collector which is characterized by a lower surface activity. Based on studies, new dialkyldithiophosphate collectors BTF 163 and BTF 1552 are suggested for use in the flotation of sulphides to increase the recovery of copper, gold and silver. The collector BTF 163 was introduced at a gold processing plant in Kazakhstan and has been undergoing industrial testing in the sulphide cycle of scheelite-skarn-sulphide ores in a factory in the far east of Russia. The collector BTF 1552, which increases the recovery of silver and gold by 3%, was approved for industrial testing in another far-eastern factory. A modification of the reagent BTF 1552, the new reagent BTF 1522, was introduced in the flotation of copper-zinc ore at a factory in Kazakhstan."

Jan 1, 2014

By R. ?. Sherembayeva, ?. ?. ?uktybayeva, ?. B. Rakhimbekova, N. ?. ?m?rova

"Studying the interaction of the phosphorus-containing flotation reagent with the components of the flotation system ""liquid-gas-solid"" during flotation of non-ferrous metal ores allows regulating the enrichment process. The phosphorus-containing reagent-collector anabasinium-O,O-dimethyl-thiophosphate has beensynthesized under laboratory conditions and the concentrated aqueous solution of anabasin hydrochloride and the 40% solution of sodium hydroxide have been used as the raw material. The phosphorus-containing reagent has been obtained by interaction of the anabasine base, sulfur and dimethyl phosphite, due to sulfur and nitrogen atoms it can form complex compounds with heavy metal ions.Studying flotation of copper-sulfide ore of the Sayak field with the use of the phosphorus-containing reagent-collector anabasinium has been performed in the open and closed cycles. The degree of ore grinding was 60- 62% of the class -0.074 mm. There has been established the dependence of the ore flotation parameters on: a) pH of the pulp; b) the consumption of the reagent-collector anabasinium.The effect of the pulp pH on the technological parameters of copper ore flotation has been carried out with a reagent regulator that increases the difference in the surface properties of the minerals to be separated.There has been used lime as the regulator of the medium, the consumption of which varied from 750 to 1500 g/t; the consumption of the reagent-collector anabasinium was 10, 15, 20 and 25 g/t.It has been found that when flotation of copper ore without the use of lime at pH equal to 7.8 and at the reagent consumption, g/t: anabasinium - 25, T-92 - 55, copper recovery in the concentrate is 92.72%, the quality of concentrate is 7, 1%.In flotation according to the factory mode (the consumption of xanthate is 44 g/t, T-92 is 55 g/t, pH = 7.8 (without lime)) of copper ore, copper recovery in the concentrate is 87.38%, the concentrate quality is 7, 97%, with reducing the xanthate consumption to 25 g/t copper recovery is reduced to 83.39%, the quality of the concentrate is up to 6.69%.In the experiments using the factory reagent mode in the closed cycle, with the xanthate mass consumption of 44 g/t, T-92 blowing agent of 55 g/t, the third recleaning concentrate contained 19.13% copper with recovery of 86.89%.Using a phosphorus-containing reagent instead of xanthate with the same flow rate, the third recleaning concentrate with the mass fraction of copper of 19.82% has beenobtained with recovery of 87.77%."

Jan 1, 2018

By Juan B. Yianatos

"After almost 100 years, since the first commercial application began in Australia, flotation has shown an extraordinary growth and nearly 2 billion tons of ore per year are presently treated by flotation processes. During this time flotation has promoted a wide scope of research activities ranging from fundamental chemistry and hydrodynamic studies to studies of industrial operations. In general, fundamental studies have been mainly related to ideal situations. In recent years, however, large efforts have been focusing on achieving a better insight into the actual sub-processes provided by the development of new and more sophisticated instrumentation. Since the massive incorporation of flotation columns, around 15 years ago, a renewed interest in flotation fundamental studies, process modelling and new cell designs have been observed worldwide. The key role of the froth has been recognized as an independent and sometimes rate limiting process step. Thus, separation of pulp and froth process stages seems the most appropriate in terms of process modelling, diagnostic, design and scale-up purposes.In relation to flotation equipment development, until the middle of the 1970?s, only the sub-aeration mechanical cells were dominant. Since the 1980?s, the use of pneumatic cells and forced air mechanical cells has emerged strongly. Also, in the last decade, flotation equipment has shown a dramatic increase in size, reaching values of 200m3 in unitary mechanical cells and more than 300m3 in columns. The general feeling, however, is that, despite the great advance observed in terms of process knowledge, the mechanisms and principles of industrial flotation cells design and scale-up are still not fully understood.Advances in process instrumentation and control now in use allow for more efficient operations, both in metallurgical performance and savings in operating costs.INTRODUCTIONFlotation is a widely used process within the minerals processing industry, as well as being used for water treatment and de-inking of recycled paper. Froth flotation started in Australia at the beginning of the 20th century and since then flotation technology has made significant advances. Flotation was firstly applied to sulfide ores. The largest tonnages treated by flotation are copper and copper/molybdenum ores, handling about 50% of the total ore processed. Also significant are phosphate, iron ore and coal treatments. At present, Chile is the foremost copper producer in the world with around 35% of the world?s production. Figure 1(a) shows the evolution of copper production in Chile over the last decade. The total amount of fine copper produced in year 2001 was 4.7 million tons, from which 3.2 million tons was processed by flotation while 1.5 million tons went through LIX-SX-EW processes, which also showed significant development during the same period (Anon, 2001). The total flotation treatment of copper ores in Chile is about 325 million tons per year (Anon, 2002), so the world treatment of copper ore by flotation can be estimated at about 1 billion tons per year. Consequently a total of nearly 2 billion tons of ore per year is presently processed worldwide by flotation (Fuerstenau, 2001). In order to handle the higher tonnage of low-grade ore, a worldwide trend towards the development and use of larger flotation machines began in the 1960?s. Figure 1(b) shows that the trend became extremely marked from the beginning of the 1990?s, which is consistent with the strong increase in copper production during the same period."

Jan 1, 2003

By Milind Chikhale, Ranjeev Kumar, Keshav Tyagi

Ore characterisation including mineralogy and beneficiation testwork of an ore is very important for determination of possible products and their quality. The results of such study help in ascertaining the beneficiation process route for the ore. The present study deals with ore characterisation study and beneficiation testwork on the samples of hematite iron ore with goethite impurity. The characterisation study reveals that the hematite is under alteration stage to goethite which has become an integral part of hematite. High goethite/limonite content is enhancing the loss of ignition content of the ore and reducing its Fe content. The findings indicate that in case of hematite iron ore associated with goethite and limonite, it is difficult to achieve high grade of concentrate above 65% Fe. It depends on the amount of goethite and limonite minerals and their association with hematite. These minerals contain aluminous impurities and hence, their rejection becomes essential. Separation of limonite and of goethite to limited extent is possible. In case of goethite, effective liberation is not achieved where it occurs as surface alteration product of hematite grains. The gangue mineral reported are clay and gibbsite, and are closely associated with iron minerals. The test work results indicate the grade and recovery of Fe along with alumina and silica content in lumps, sinter fines and pellet feed fines that can be achieved for the different ore types vis-a-vis the percent of available hematite in the ore. The recovery of iron is dependent on the hematite available and the loss of iron values in tailings is more because of rejection of limonite and goethite.

Jan 1, 2014

By Zhang Yuejun, Feng Tianran, Shen Zhengchang, Han Dengfeng

"With continuous mining industry development and dressing plant scale expansion, flotation cell is developed towards to large scale and intelligence. Based on flotation cell scale-up theory and industrial practice, KYF-320 air-forced mechanical flotation cell with effective volume of 320m3 was successfully developed by Beijing General Research Institute of Mining and Metallurgy (BGRIMM) and adopted by China Gold Inner Mongolia Mining Co., Ltd, Luming project of China Railway Resource Group Co., Ltd, and Toromocho project of Chinalco in Peru. In this paper, the structure and technical characteristics of KYF-320 flotation cell are introduced, and the application of that equipment in China Gold Inner Mongolia Mining Co., LTD is demonstrated. The tank of KYF-320 flotation cell is cylinder-shaped, 8200mm in diameter and 7500mm high, with double froth lauders and large inclined angle cone bottom. 16 sets of KYF-320 flotation cells of which the processing capacity is 26,000,000 tons/a, are used in the second phase project of China Gold Inner Mongolia Mining Co., LTD. Their stable running shows the long life of impeller and stator and the power intensity (power consumption divided by effective volume of flotation cell) of KYF-320 flotation cell is only 0.73kW/m3 which is significantly less than that of small scale flotation cells. The industrial production obtains good results that the Cu grade of final concentrate of entire flotation circuit is 22.90% at the recovery of 86.73%, when Cu grade of feed is 0.35%, which indicates that KYF-320 flotation cell has good performance and can be widely used in large scale mine."

Jan 1, 2014

The multiphase reactive flow in process equipments, e.g., fluidized beds, involves complex coupling among flow, heat/mass transfer and reaction kinetics over scales ranging from molecules, sub-particle eddies up to equipments. Conventional two-fluid model (TFM) ignores the effects of meso-scale structures, and hence is not suitable for describing the intrinsically multi-scale heterogeneity within multiphase systems. To be consistent with the meso-scale structures, we proposed a structure-dependent multi-fluid model (SFM), and closed its drag force by invoking the stability condition defined in the energy-minimization multi-scale (EMMS) model. The SFM reduces to the conventional TFM if homogeneous distribution is assumed within each grid, and reverts to the original EMMS model if it is used to describe steady state, global behavior of a fluidized bed. The multi-scale computational fluid dynamics (CFD), which is characterized by coupling of TFM and EMMS drag coefficient, can then be viewed as a simplified solution of the SFM. We demonstrate that the SFM significantly improves the accuracy and at the same time enables higher efficiency by allowing for much coarser grid used than in TFM. Recent application of it in 3D, full-loop, transient simulation of industrial processes, e.g., fluid catalytic cracking, coal combustion, gasification, kaolinite clay calcinations, shows its advantages in helping design and troubleshoot multiphase process equipments. Keywords: meso-scale, SFM, multiscale, CFD, simulation, structure, EMMS, multiphase

Sep 1, 2012

By J. R. Cui

The production of electric and electronic equipment (EEE) is one of the fastest growing areas. This development has resulted in an increase of waste electric and electronic equipment (WEEE). In view of the environmental problems involved in the management of WEEE, many counties and organizations have drafted national legislation to improve the reuse, recycling and other forms of recovery of such wastes so as to reduce disposal. Recycling of WEEE is an important subject not only from the point of waste treatment but also from the recovery of valuable materials. Consumer electronic equipment (brown goods), such as television sets (TV), radio sets, and video recorders, are most common. However, recent work on recycling of waste electric and electronic equipment (WEEE) primarily focused on personal computer and printed circuit boards scraps. Based on a detailed characterization study of consumer electronic scraps, recycling of TV scraps oriented to recovery of metals is highlighted by utilizing air table separation, eddy current separation, and optical (metal) sorting process. The result indicates that a high recovery of copper could be obtained by utilizing an effective gravity separation process. The separation results reveal that air table separation is an effective technology to recover metals from consumer electronic scraps. By using a DGS table, approximately 90% of non-ferrous metals were recovered in the heavy product with a purity of 40%. Printed circuit boards and cables in TV scrap cause metals loss due to the fact that metals in printed circuit boards and cables are not liberated from plastics and ceramic materials. The study shows that eddy current separation and optical (metal) sorting process provide alternatives for recovery of metals from shredded TV scraps.

Jan 1, 2014

By P. Somasundaran, Tarun Bhambhani, D. R. Nagaraj, P. Patra

"Certain non-sulfide gangue minerals are known to have a detrimental impact on flotation performance. When present in large amounts, they can negatively affect recoveries, grades and throughput at current operations, and dictate the viability and economics of a greenfield project. While the problem has been investigated for a long period of time, a scientific understanding of the mechanisms by which these minerals affect performance has not been obtained, and no acceptable solutions have been developed. This study focused on the role of physical aspects (e.g. shape, size and morphology) of these minerals as the underlying factors for poor performance. Flotation tests were conducted using model mineral systems to understand the impact of one phyllosilicate mineral (muscovite) on flotation kinetics, recoveries and grades. The study reveals that there is minimal impact on flotation kinetics, no impact on recoveries, but a very strong detrimental impact on concentrate grade. The traditional mechanisms of transport such as true flotation and entrainment are not sufficient in describing the extent of transport. The transport is attributed to the unique platy morphology of muscovite, which allows for action of buoyancy forces. Data also shows that the muscovite transport to the froth phase depends on particle size; coarser sized muscovite (100-150@) report to the froth phase in much larger amounts than medium sized muscovite (50-100@). At finer size fractions (<50@) the transport is also increased, and this is likely due to entrainment."

Jan 1, 2014

By H. M. Yang

Structural alteration of pyrophyllite during mechanical activation in a planetary mill was investigated by X-ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FTIR) techniques. Mechanochemical effect markedly promotes the decrease in reflection intensities with increasing the grinding time. Prolonged grinding causes the pyrophyllite to become the amorphous structure. It can be indicated that pyrophyllite is very susceptible to alteration by grinding. Crystal size (d006) of pyrophyllite appears to be a limit after 2h grinding. IR spectroscopy analysis shows a little alteration in the bands of pyrophyllite after mechanical activation. The results indicate that the ordered structure of pyrophyllite is destroyed and lattice deformation occurs. Porous silica was then successfully prepared via leaching the mechanically activated pyrophyllite. Pyrophyllite was first ground for 6 h. Ground samples were subsequently leached with 4 M hy-drochloric acid at 80 °C for 2 h to produce porous silica with specific surface area of 188.1 m2/g, total pore volume of 0.18 mL/g and average pore size of 3.9 nm from N2 adsorption analysis. Otherwise, the porous silica obtained from direct leaching of the original pyrophyllite only has a specific surface area of 4.3 m adsorption analysis. 2/g and total pore volume of 0.03 mL/g. It is inferred that grinding is favorable for the formation of microstructure pores. It offers a simple and convenient route for the preparation of porous materials from natural minerals.

Jan 1, 2014

By Y. Q. He

The methodology of active pulsing air separation is a new method for dry material classification. Especially, it is suitable to electronic scraps disposal and re-utilization. By studying the difference of drag coefficients of the particles moving through areas of varying Reynolds numbers, and considering the extra-mass forces acting on the particles in the active pulsing air field, models of the dynamic motion which particles follow were developed. A computer simulation was prepared that showed the traces of particles with different densities and/or diameters, but similar aerodynamic characteristics, as they moved through the turbulent flow, to modify and define the parameters of the models. The simulation was found to predict the observed results with artificial tracing spheres being separated by the laboratory equipment. The separation performance, as being affected by the particles, nature, the air velocity, the pulsing frequency and the air pattern, is discussed. In general, lower density particles are more responsive to variations in airflow velocity. In addition, an industrial scale active pulsing air separator was designed, and it provides a new and efficient method for resource re-utilization in China.

Jan 1, 2014

By C. Igathinathane

Coal is the most widely used fossil fuel in the world, providing more than 25% of world?s electrical power. Since, the behavior of coal particles in crushing and grinding circuits, concentration operations, and solid-liquid separations is strongly dependent on size, a reliable and accurate measurement of particle size and particle size distribution (PSD) is a vital aspect in coal cleaning. This paper presents a method for the characterization of ground coal particles using image analysis. We utilized a machine vision (MV) approach that used a document scanner as the imaging device and a user-coded ImageJ plug-in that processed the image and automated the PSD analysis and output results in textual and graphical forms. This approach used a sum of volumes (SVolume) as weighting factor for particle length as the primary dimension of analysis and was successfully applied to ground coal. The plug-in was further improved for computational performance in this study. Mechanical sieving (MS) was also used to compare the MV results. MV results showed that the PSD of ground coal followed a uni-modal normal distribution, and the log-normal plot against particle size exhibited a linear trend for most of the range. MS results, however, had three linear segments, when the width-based sieving results were transformed to lengths by applying the shape factor (width/length), but a definite deviation between the PSD plots was observed. This study demonstrates successful application of the MV SVolume approach for PSD analysis of ground coal, which can be extended to similar particulate minerals and products. Keywords: dimension, fiji, image j, image analysis, coal, particle size, plug-in

Sep 1, 2012

By P. Gao, J. W. Yu

"Magnetizing roasting-magnetic separation is an important route for the beneficiation of refractory iron ores. In this investigation, a pilot-scale fluidized magnetizing roasting reactor was introduced and used to study the effects of roasting temperature and the flow rates of reducing gas CO and fluidizing gas N2, on the magnetizing roasting performance of an Anshan-type carbonate-bearing fine iron ore. The results showed that the hematite was almost reduced to magnetite by a gas mixture of 4 m3/h CO and 1 m3/h N2 at a roasting temperature of 540 °C. Under the optimized conditions, a high-grade magnetic concentrate assaying 66.1 wt.% Fe with a recovery rate of 91.2% was achieved from an Anshan-type carbonate-bearing fine iron ore assaying 42.0 wt.% Fe. The XRD, VSM, and optical microscopy analyses revealed that the siderite was successfully converted to magnetite by roasting. Some coarse hematite particles were difficult to reduce to magnetite completely; however, these generated magnetite particles with a fine hematite core could also be effectively recovered by magnetic separation after liberation from gangue minerals due to their strong magnetism. INTRODUCTION Magnetizing roasting followed by low-intensity magnetic separation has been considered as an effective solution, both technologically and economically, when upgrading refractory iron ores (Zhang et al., 2012; Peng et al., 2012; Li and Zhu, 2012). According to the type of roasting reactor, the magnetization roasting can be divided into shaft furnace roasting, rotary kiln roasting, and fluidized bed roasting (Zhu and Li, 2014).Shaft furnace magnetization roasting system is mainly composed of heating and reduction processes. The hematite ore is first heated to 700~800 °C in the heating zone, then falls into reduction zone where the weakly magnetic hematite is reduced to magnetite by coke oven gas at 550~600 °C (Yan et al., 2012). However, several years of engineering practices indicate that the shaft furnace can only process the hematite ores with a granularity of 15 ~75 mm, and the shaft furnace roasting is also characterized by heterogeneity of roasted product. Hence, the shaft furnace magnetization roasting technology is gradually replaced by high-gradient magnetic separation with the development of high-gradient magnetic separator. The rotary kiln generally handles the hematite ores with a grain size of less than 30 mm (Zhu and Li, 2014), however the formation of clinker ring in the rotary kiln will affect the yield of iron resource. In the fluidized bed furnace, the hematite ore is shaken up by an upward current of gas which maintains the individual particles in suspension (Yu et al., 2018). The precise adjustment of the gas velocity to the particle size and the specific weight of the hematite ore, make it possible to generate a floating mixture of gas and solids which behaves almost like a liquid (Yu et al., 2017a). The process is reported to have the following advantages over the other roasting techniques: ease of control due to absence of moving parts within the reactor, homogeneity of roasted products, ability to handle fine particles, and high efficiency of heat transfer and mass transfer (Li et al., 2015; Yu et al., 2017b). However, the simultaneous heating and reductive magnetization of hematite ore occur at the same place in the conventional fluidized bed reactor. Therefore, the reductive atmosphere, as well as the safety and stability of anti-explosion are hard to be controlled. Besides, the roasting temperature for conventional fluidized bed furnace is usually up to 950~1150 °C (Liu et al., 2017). Thus, the formation of clinker ring caused by high temperature will affect the operating efficiency."

Jan 1, 2018

By Ramon V. V de Araújo, Roberto B. E Trindade, Pablo R. Fica-Piras

"Lead has been reported to affect blood vessels and kidneys. It also produces adverse effects in the mental and physical development of children and nervous system of adults. It is also considered as a possible cause of cancer. Because of all these threats to the human life, the reduction of its environmental occurrence, by means of recycling, is an important additional advantage to the usual ones derived of the procedures of the secondary metallurgy: lead can be recycled several times maintaining its characteristics equivalent to the primary one.Furthermore, this way of producing the metal avoids the environmental impacts of primary lead melting. Also, as an additional advantage, it triggers the metallurgical process with a raw material in what we observe higher lead content than in the natural ores. Some of the potential sources for these purposes are: ashes, slags, electrode residues, anodic muds, spent electrolytes, solid and liquid wastes, industrial or automotive catalysts, worn-out or obsolete equipment components and/or final consumption products.About 40% of world’s lead production comes from automotive batteries, mainly composed of four parts: plastic box, electrolyte (diluted sulphuric acid), contacts and connectors of Pd-Sb and plates (PbSO4, PbO2 and PbO). The plates represent 75% of the total mass. Metallic parts can be melted at moderate temperatures and then refined. The remaining fraction, constituted by the non-metallic portions, can be recovered by hydro and electro-metallurgical routes. These routes are preferred instead of pyrometallurgical ones due to the ultimate emissions of lead particulates and sulphur dioxide.The principal constituent of the residual paste of batteries is the lead sulphate. In this process, the paste is treated in two stages: in the first, lixiviating with Na2CO3 (desulphurization of the paste), obtaining PbCO3 and Na2SO4; in the second, the lead carbonate is lixiviated with HNO3, producing Pb(NO3)2, soluble, that can be converted to metallic lead by electrolysis. The reaction of PbSO4 with Na2CO3 in aqueous solutions is fast: the global rate is limited by the diffusion of the carbonate ions inside the reaction medium."

Jan 1, 2003

By S. Banisi, Seyyed Omid Mousavi, Alireza Ghasemi

Discrete Element Method (DEM) is extensively used to simulate the behaviour of particles in various processing units. This method is based on modelling the forces acting between particles in any contact and consequently calculating the new position of particles. The high number of elements and numerous equations needed have made the required computation time very long even using computers with very fast processors. The required computation time mainly depends on the time step. If the time step is chosen very short, the computation time will significantly increase. On the other hand, if the time step is chosen very long, the simulation will be in error due to not fully observing the contacts. In DEM calculations, the time step is chosen as a fraction of the collision time. In this research, a relationship was proposed between the contact time fraction and the error of simulation. In other words, to select the time step in addition to physical parameters, the accuracy of the simulation was also accommodated in the frequently-used relationships. The simulation error was defined as the relative difference between the initial restitution coefficient and the restitution coefficient obtained after simulation. The required time steps to arrive at the simulation error of 5% were calculated for two common contact force models namely, Hertz-Mindlin and linear spring-dashpot. The simulation was performed for two particles with radius of 3 cm, elasticity modulus of 210 GPa, Poisson&apos;s ratio of 0.3 and relative velocity of 0.5 m/s. The required time steps were found to be 2.3 and 0.19 µs for the Hertz-Mindlin and the linear spring-dashpot contact force models, respectively. Results showed that with a scaling-down the modulus from 210 GPa to 2.1 MPa, the required time steps for the Hertz-Mindlin and the linear spring-dashpot contact force models, with an equal simulation error, increased by 100 and 316 times, respectively.

Jan 1, 2014

By Hiroshi Sasaki, Herman D. Mendoza

"The surface-chemical property of nickel slag fiber was modified in aqueous media in order to act as an active and efficient collector of colloidal amorphous silica from geothermal effluent. Colloidal amorphous silica (0.05 µm) from geothermal wastewater causes operational and ecological problems. It clogs geothermal pipes and waterways, and when disposed to the environment poses hazardous effects on both the flora and fauna ecology. Because colloidal amorphous silica is extremely fine and remains in suspension in aqueous media, conventional solid/liquid processes to remove colloidal silica from its bulk liquid are rendered ineffective.A rapid separation technique is then developed to remove effectively amorphous colloidal silica from its bulk liquid by attaching the extremely fine particles of silica onto a nickel slag fiber coated with magnesium hydroxide, Mg(OH)2. The nickel slag fiber has the following characteristics: a high surface area and predominantly possesses negative charge in aqueous media with an iso-electric point at pH ~2.5. When soaked and saturated with Mg(OH)2 solution, the surface of the nickel slag fiber becomes coated with fine and compacted Mg(OH)2 precipitates. This modifies the surface- chemical property of nickel slag fiber transforming the negatively charged surface into a positively charged surface in aqueous media with an iso-electric point of around pH 11.8, which corresponds to the iso-electric point of Mg(OH)2. When geothermal effluent containing negatively charged colloidal amorphous silica particles (i.e.p. of silica is pH 2) is passed through a column-bed packed with surface-chemically modified nickel slag fibers under natural pH conditions, the colloidal amorphous silica particles are recovered by attachment onto the surface of the surface- modified nickel slag fiber. The recovery of colloidal amorphous silica by attachment is 97-99%, resulting in the production of a relatively clean and silica free output. Aluminum hydroxide, Al(OH)3, was also used to modify the surface –chemical property of the nickel slag fiber. In the same way, it also exhibited a positive response with the collection of colloidal amorphous silica from its bulk liquid, but yielding a lower recovery of 90%. This may be attributed to the lower surface potential and iso-electric point of pH 9.3 for Al(OH)3. The separation process was evaluated and analysed using existing potential energy theories. Figure 1 shows a micrograph of the surface of an unmodified and the Al(OH)3 –modified surface of nickel slag fiber."

Jan 1, 2003

By R. Venugopal

Hydrocyclones have been used extensively for more than 100 years to classify mineral slurries for recirculation in grinding circuits. Sometimes hydrocyclone classification is carried out in more than one stage to improve the efficiency of classification. Factors affecting separation efficiency include fluid velocity, density, and viscosity as well as the mass, size, and density of the particles. The geometric configuration also affects its efficiency; it includes parameters like cyclone diameter, underflow and overflow diameter, position of vortex finder, height of the cyclone, feed inlet geometry, and diameter etc. Besides changes in the basic parameters some modifications in cyclone has also been introduced from time to time which have affected its efficiency, some of these are :-(i).Introduction of magnetic force along with the centrifugal and drag force to control the flow of the magnetic particles inside the chamber.(ii). Introduction of sparger, air is introduced in the chamber in the form of bubbles, to control the flow of fine particles and hydrophobic particles. (iii). Introduction of dilution technologies for the dilution of thickened underflow. (iv).Introduction of new model. In spite of wide use and simple geometry, the real working principle of hydrocyclone chamber is extremely complex because of the swirling turbulent flow inside the device. In order to get more knowledge about hydrocyclones and to increase its efficiency, past 10-15 years simulation techniques are being developed. The simulation models also enabled a deeper insight into the static and dynamic behavior of hydrocyclones. Therefore, more emphasis on simulations by methods like Computational Fluid Dynamics (CFD), Finite Element method (FEM) is given. Overall, a status review of the work carried out on the analysis of hydrocyclone performance, modeling approaches and its contribution in the efficiency of mineral processing operation is highlighted.

Sep 1, 2012