Search Documents

By Raquel Franco de Souza Lima, Isao Matsuoka

"Microflotation studies and abstraction experiments were conducted with synthetic oxide spinels relating to chromite (MgCr2O4, FeCr2O4, FeFe2O4 and FeAl2O4), using sodium oleate as collector. An attempt was done to correlate this data with the speciation of oleate in the bulk solution and at the interface solid-water, to explain the floatability curves. The microflotation tests were conducted using a microflotation cell. The abstraction of sodium oleate was measured at 25°C, with one gram of synthetic spinel and the abstraction time was 30 minutes. After centrifuging, the residual oleate concentration in the supernatant was measured by using the spectrophotometric method described by Mizuniwa et al. (1977), that covers the range from 1.5 to 9 ppm. To cover the range from 0.2 to 1.5 ppm, the residual oleate concentration was measured using the spectrophotometric method described by Gregory (1966). The amount of oleate abstracted was calculated from the difference between initial and residual (equilibrium) concentrations.Figure 1 shows the floatability of FeCr2O4, FeAl2O4, FeFe2O4, MgCr2O4 as a function of pH and sodium oleate concentration of 1 x 10-5 M. The IEP of each sample is indicated in the figure by a vertical line in the horizontal axis. The chromium-bearing spinels FeCr2O4 and MgCr2O4 show the lowest isoelectric points (IEP), around pH 6, while in the case of FeFe2O4 and FeAl2O4, the isoelectric points lie at pH 6.5 and 7.3, respectively. It is seen that the flotation-pH curve for FeFe2O4 has a peak at the pH of the IEP, while flotation peak for FeCr2O4 appears at pH below the IEP and that of MgCr2O4 does at pH above the PZC. On the other hand, FeAl2O4 is floated at pH range between about 4 and 7,3 (IEP). This suggests that the pH value at which the maximum flotation occurs is dependent on the sort of spinel to be floated, though it appears in the vicinity of the respective IEP."

Jan 1, 2003

By Herman D. Mendoza

A rapid recovery/recycling process was introduced utilizing the surface-chemical properties of finely dispersed mercury and alumina (Al2O3) fibers in aqueous environment. The conventional method of amalgamation or .ball milling. involves the mixing of a substantial amount of mercury to collect free gold during the grinding stage. In effect, a portion of the mercury is transformed into minute droplets that readily float and disperse in the amalgamation effluent. The fine droplets of mercury in the dispersion readily attached onto the positively charged macroscopic alumina fibers (i.e. = pH 9.8) at conditions pH 3 to 10. When an effluent from settling procedure after an amalgamation-grinding stage is passed through a column-bed packed with alumina fibers, maximum collection of negatively charged finely dispersed mercury occurred at pH 3 to 6. The collection/attachment efficiency was 99.5%. The collected droplets of mercury, which are left in the column-bed of alumina fibers, were subsequently rinsed with alkaline solution at pH 10 to 11.5. At these conditions, both mercury and alumina fibers carry negative surface potentials and resulted in the partial detachment of mercury from the alumina fibers. The detachment efficiency was only 30-35%. The attachment/detachment mechanisms in this study were analyzed using the DLVO theory.

Jan 1, 2003

By Zhangm Zeqiang, Manman Lu, Hanquan Zhang, Hong Yu, Jintao Fu

"Pelletizing is an important technique in the ironmaking industry. Artificial and natural magnetites are materials that are widely utilized in the iron ore pelletizing process. In this work, the pelletizing characteristics of these two types of magnetite have been investigated in detail. The obtained results shown that in contrast to natural magnetite, the artificial magnetite concentrate exhibits stronger hydrophilicity, lower electronegativity, larger specific surface area, and rougher surface. In addition, the green pellets produced from the artificial magnetite concentrate are characterized by a higher compressive strength as compared to that of the pellets obtained from the natural magnetite concentrate. However, the shock temperature of the artificial magnetite pellets around 255 C is significantly lower than the threshold specified by the industry. The balling characteristics of the material obtained by mixing 20% of the artificial magnetite concentrate with 80% of the natural magnetite concentrate are considerably improved with respect to those of the individual components.INTRODUCTION Pelletization is an essential process of the ironmaking industry in China. Since the pellets produced from iron ore exhibit high mechanical strength, good particle granularity, and uniform shapes, pelletizing high-grade iron ores with good metallurgical reducibility can lower the coke ratio, improve their technico-economic index, and reduce the cost of processing pig iron in blast furnaces[1, 2]. Presently, high-grade magnetite is a material utilized for pelletizing various iron ores across the globe. However, its natural deposits have been depleting rapidly in recent years; as a result[3], China’s dependence on the foreign high-grade iron ores exceeded 70% in 2009 and reached the level of 87% in 2016. Hence, possible methods for the efficient cultivation of limonite, siderite, hematite, and other refractory minerals that correspond to low-grade, finely sized, inhomogeneous, and scattered iron ores have attracted significant attention [4, 5]. In particular, magnetization reduction roasting and magnetic separation techniques, which are widely utilized for obtaining high-grade artificial magnetite, represent effective ways of processing iron ores that can alleviate the scarcity of natural magnetite resources [6, 7]. The artificial magnetite produced by magnetization reduction roasting exhibits different characteristics as compared with those of natural magnetite (including the degree of hydrophilicity, surface potential, specific surface area, and other surface physicochemical properties[8-11], which significantly affect its pelletizing behavior. In this work, the surface characteristics of artificial and natural magnetites are investigated in detail, and their effect on their pelletizing properties (such as green ball strength, heat stability, and pelletization rate) are examined."

Jan 1, 2018

By K. Anand Rao

Extensive exploration for uranium metal by the Department of Atomic Energy in India led to the discovery of new carbonate host rock uranium deposits Tummalapalle and Gogi, which are located in southern part of India. Alkaline leaching at elevated temperature and pressure using autoclave is the central unit process in the overall strategy for extraction of uranium from these new ore deposits. Autoclave leaching is affected largely by intrinsic nature of the ore and by the process variables and the equipment settings. In order to understand such a complex process and also to be able to predict the process performance under randomly (ore grade, uranium mineralogy, gangue mineralogy etc.) and consciously perturbed variable settings (partial pressure of oxygen, temperature, concentration of leachant, stirring speed and time), sound and robust mathematical models are needed with analytical and/or numerical solutions. Present investigation attempts to develop a variant of kinetic correlation based on shrinking core model for batch alkaline leaching process in an autoclave. The leaching model incorporates particle size distribution according to popular Gates-Gaudin-Schuhmann equation, rather than assuming a single mean size for all the particles participating in the leaching reaction. Kinetic experimental data generated in autoclave leaching of Gogi uranium ore was used to evaluate various constants of the model developed. The ore sample used for experiments assayed 0.21 per cent U3O8. The partial pressure of oxygen was varied between 0.15 to 6.5 atm, temperature from 343 K to 438 K, concentration of sodium carbonate leachant in the range 0.47 g mol/L to 0.94 g mol/L, and the stirring speed from 573 rev/min to 900 rev/min in the experiments. The goodness of fit of the leaching process model is found to be >0.95. Morphological studies carried out on leached and unleached particulate matter using Scanning Electron Microscopy with Energy Dispersive X ray analyses are included in the present study.

Sep 1, 2012

By H. R. Zhang

In this paper two optional production processes are presented for reasonable utilization of primary sylvinite in Qinghai province, China. The two kinds of products as chlorine-free potash fertilizers; potassium sulphate or potassium magnesium sulphate can be obtained. In the course of potassium sulphate production, using primary sylvinite from Qinghai salt lake as raw material with impurities such as sodium chloride and insoluble in primary sylvinite, it must be prepared by flotation before being converted into potassium sulphate. This final product has found wide use in tobacco industry in China. However, in some cases Chinese farmers would rather buy the fertilizer of potassium magnesium sulphate than high quality of potassium sulphate. With flotation process which is a little different from above mentioned, the potassium magnesium sulphate fertilizer may be produced by washing one of the flotation concentrate presented as picromerite, while another concentrate containing potassium chloride is treated as by-product.

Jan 1, 2014

By Marlize Barkhuizen, Chris Aldrich

"Owing to environmental constraints, safety considerations and competitive pressures, the development of model-based process control and other automated systems have experienced considerable growth in the last few decades. Reliable process models are usually critical to the successful implementation of these systems. In complex processes, these models are often constructed from process data, as modelling from first principles may not be feasible or cost-effective.Even so, modelling or identification of nonlinear systems from historic plant data can be a daunting task and in the process industries the problem is complicated by the presence of noise from various sources, nonstationarity of the data, intermittence, such as observed in particulate flows, etc. Traditional methods, such as frequency analysis and linear modelling do not handle these systems well. Similar problems arise with the application of nonlinear theory developed over the last few decades, where much of the analysis depends on embedding of the data in a phase or pseudophase space, since these methods were not originally designed to deal with noisy systems.With singular spectrum analysis, the data are embedded in a high-dimensional reconstruction, followed by the introduction of a new coordinate system, where the origin is moved to the centroid of the reconstructed system states and the axes are represented by the dominant principal components of the states (points)."

Jan 1, 2003

By M. Bergerman

Sossego was the first Vale SAG mill operation to process copper-gold ore. It is located in Para state, south east of Amazon region in Brazil. The comminution circuit was designed to treat 41 000 metric tons per day comprising primary crushing, one 11.6 m SAG mill operating in closed configuration with cone crushers, followed by two 6.7 ball mills. In the first three years of continuous operation Vale investigated alternatives for obtained improved performance of the circuit by investigating operating conditions, mainly focusing on SAG mill. A number of actions were then implemented, which resulted in significant increase in overall production. Vale then decided to further assess the performance of the comminution circuit as a function of ore characteristics. A comprehensive ore characterization program was then conducted, together with the calibration of mathematical models on the basis of surveys carried out at the industrial circuit. The simulator was then used to predict the production level associated to each ore type, as well as to establish the optimized circuit configuration and tailored operating conditions. The ongoing validation program is planned to consolidate the selected strategy, as well as showing the benefits in adopting such indices in mine planning, as opposed to rather simplistic approaches. This paper describes in detail the main aspects of optimizing the industrial circuit performance, as well as the successful method for predicting the production as a function of ore characteristics.

Jan 1, 2014

By Heribert F. Broicher, Arne Volland

"The analysis of laser-induced fluorescence (LIF) combines remote sensing techniques with laser spectroscopy. Over variable distances different rock types are identified or changes in the quality of one rock type are recognised. LIF Analysers operate non-destructive, non-contact, on-line and in real-time. Installed over conveyors or over driveways the analysers ""look"" at the moving bulk solids 20 times per second and provide in real-time information for downstream sorting, blending or optimisation of processing. LIF Analysers recognise rock types (hardness information or dilution control), degrees of alteration, degrees of oxidation and –semi-quantitative- content of certain minerals in an ore. Only under favourable conditions quantitative assay information can be obtained, as e.g. the phosphorus content of Kiruna type iron ore.The main application of LIF Analysers is seen in big open pit operations, where the muck is trucked to an in-pit crusher and the crushed rock conveyed out of the pit to its respective destination: e.g. the primary high grade ore to the mill, the low grade or oxidised ore to the leach pads and the internal waste to the dumps.In underground mining and especially in block caving operations dilution control is of utmost importance. Here a LIF Analyser mounted on the back of a pick-up truck can be moved from drawpoint to drawpoint and quickly assess the degree of dilution.Closer to the mill the stockpile management based on LIF analysis will lead to stockpiles sorted according to rock type (hardness), degrees of alteration and oxidation. In case of direct feeding rom ore to the mill the knowledge of the type and quality of all the material between the in-pit crusher and the mill facilitates optimisation of e.g. reagent dosage."

Jan 1, 2003

By Y. Q. He

The dynamic behaviors of the air bubbles in the dense gas-solid fluidized bed have a significant effect on the performance of dry coal separation. The combined method of experimental measurement and numerical simulation were conducted to conduct the research of the mean diameters and rising velocities of the bubbles in the fluidized bed. The calculation models of mean diameter and rising velocity of the single bubble were proposed. The results indicate that the models of the mean diameter raised by Rowe (1976) and the rising velocity raised in this work could be used to predict the bubble dynamic parameters in gas-solid fluidized bed. With the Geldart B type of magnetite powder as the medium solids and while the gas velocity of 1.5Umf=U=2.2Umf, the mean bubble diameter along the bed height is 36mm<Db<45mm, and the mean rising velocity of the single bubble is distributed in 40~65cm/s. The results of experimental measurement, numerical simulation and model predication provide well agreements finally. Based on the uniform fluctuations of air bubbles diameters and their rising velocities, the separation experiments of 50~6mm dry coal using the mixture of 0.3~0.15mm magnetite powder and <1mm fine coal as medium solids were carried out. The results show that the probable error, E is 0.06, which indicates a good separation performance by using the gas-solid fluidized bed. Keywords: dense gas-solid fluidized bed, bubble dynamic behaviors, numerical simulation, separation performance

Sep 1, 2012

By Z. D. Tan

The continuous digestion technological conditions of phosphate tailings with high magnesium content in sulfuric and phosphoric mixed acid is studied in this paper. The influences of excess coefficient of sulfuric acid, weight liquid to solid, reaction temperature and time on conversion of P2O5 and MgO are discussed. The influence of infiltration capacity of phosphogypsum by the concentration of liquid-phase SO3 is discussed too. Under the optimal technological conditions, the conversion of P2O5 is 95.56% and MgO 98.63%, the filtration rate of phosphogypsum increases with the increasing of liquid-phase concentration of SO3, the optimal apparent concentration of SO3 is 0.135~0.14g? mL-1 in liquid-phase. The filtration rate of phosphogypsum is 1473kg? m-2? h-1. N-P-Mg compound fertilizer was produced by adding magnesia powder and inflating ammonia in filtering medium.

Jan 1, 2014

By Shobha Kumari

Coal is the prime source of energy in India. It now contributes to about 55% of the total power generation and will continue to have its major share in the energy mix of the country in the foreseeable future. Thermal coals of India, known for their wide variations in nature and categorized as difficult to wash due to their typical mineral matter association with the organic matrix, need suitable beneficiation technique for quality upgrade for improving the overall economics, efficiency and pollution free power generation. A non-coking high-ash coal, collected from Vasundhara open cast mine of the Ib Valley Coalfield, Orissa, has been characterized along with its different fractions obtained in the process of beneficiation for distribution of minerals using FTIR, XRD and ash analysis. The raw coal was fractionated by size as well as by density. It has been observed that ash yields and mineralogical composition (found to be mainly kaolinite and quartz) have no appreciable change in different size fractions, indicating homogeneous distribution of minerals in the coal matrix. However, for the different density fractions the mineral composition and ash yield have significant variations. The quartz content of the beneficiated coal visualized with 34% ash yield, as mandated by the Ministry of Environment and Forest (MOEF) for the use of coal in power plants is reduced to half of that of the raw coal. As quartz is the most abrasive mineral in coal, reduction of its proportion obviously signifies considerable reduction of wear of power plant machinery when beneficiated coal is fed to utility boiler for generation of power. The composition of the major minerals quartz and kaolinite as determined, also favors formation of ash of refractory nature during combustion. Keywords: IB valley coal, beneficiation characteristics,

Sep 1, 2012

By L. Ya Agapova

Emissions from pyrometallurgical processing of copper concentrates are usually subjected to wet scrubbing. The washing sulphuric acid so produced contains up to 0.2 g/L of rhenium, which is recovered by solvent extraction in the form of crude ammonia permeate (NH4ReO4). The mother liquor, obtained from the sulfuric acid wash, contains up to 35 g/L of rhenium and significant amounts of impurities. Crude rhenium salt is commonly processed by double recrystallization to produce marketable salt. A ton of high grade NH4ReO4 can be produced using 3.0-3.5 m3 of mother liquor. We propose an efficient technology of mother liquor pre-treatment aimed at removal of water-soluble organics with subsequent electrodialysis. Electrodialysis of mother liquor in a multichamber electrodialyzer resulted in the production of pure rhenium acid, from which a marketable NH4ReO4 is precipitated using ammonia solution. Multiple steps of recycling consisting of dissolution of NH4ReO4 salt, rhenium acid production from NH4ReO4 salt by electrodialysis and precipitation of NH4ReO4 from rhenium acid made it possible to upgrade the purity of obtained rhenium compounds by 1-2 orders of magnitude. A rhenium metal powder of 99.997% purity was produced by high-temperature reduction of high-purity NH4ReO4 with gaseous hydrogen. Rhenium metal powder of high purity can be produced from sulfate solutions of NH4ReO4 by non-platinum anode-based membrane electrolysis processes also. Keywords: rhenium, mother liquors, membranes, electrodialysis, rhenium acid, ammonia perrhenate, reduction, powder, electrolysis

Sep 1, 2012

By Rodney J. Hundermark, Sharif Jahanshahi, Shouyi Sun

"The major platinum producers in South Africa make use of electric furnaces for the melting of PGM bearing nickel - copper concentrates. To gain better understanding of the furnace operation, research was conducted at CSIRO Minerals in Melbourne, Australia. One aspect of the research project was the investigation of the factors affecting the electrical conductivity of melter type slags.Electrical conduction in slags can occur through two mechanisms: ionic and electronic. There is good understanding of the ionic mechanism. In slags containing high levels of iron, the dominant mechanism is electronic. There is limited understanding of the electronic mechanism and one of the aims of the research was to investigate this mechanism further.Experimental work was carried out on Al2O3.CaO.FeOx.MgO.SiO2 slags similar in composition to the melter slags. Conductivity increased significantly with iron oxide content. Above 20wt% FeOx, electronic conduction was significant and the conductivity varied with the oxidation state of the slag. As the iron oxide content was increased further, the electronic mechanism became more dominant. The conductivity reached a maximum at around pO2 = 10-7 to 10-4 atm., although this value was dependent on the total iron oxide content and basicity of the slag."

Jan 1, 2003

By N. Johnson, J. Quinteros

With the general trend across all commodities towards the treatment of lower grade ores, it is becoming increasingly important to develop efficient protocols for comprehensive mineralogical characterisation to allow the development of the most appropriate strategies for processing an ore. In the case of silver, there are more than 200 known silver bearing minerals which can make it challenging to identify them. Knowledge of the deportment of silver within an ore is one of the factors used to determine an appropriate processing strategy. Automated SEM-based tools are commonly used for mineralogical characterisation but the low-grade together with the large number of minerals that are potential hosts for silver means that often, complementary analytical tools must be used in order to properly account for the silver. The work presented in this paper is a demonstration of the approach that should be taken when identifying the deportment of silver in complex ores. Three complex, low-grade silver ores were characterised using the approach. The insights from the mineralogical characterisation were then used to inform the metallurgical testing that was undertaken. The results from the batch flotation testing clearly demonstrate the importance of understanding the mineralogy in order to select the most appropriate metallurgical processes.

Jan 1, 2014

By X. Tan

In this paper, the application of the metallurgical residue produced from oceanic cobalt-rich crusts leaching process is studied in the area of wastewater treatment. The modification of the sulfuric acid leached residue and the adsorption behavior behaviour of heavy metal ions such as (Pb(II), Cu(II), Zn(II), Cd(II), Ni(II), Mn(II), Co(II), As(III)) in the waste-water on the surface of the residue are investigated. The rate of adsorption efficiency of heavy metal ions in the wastewater on the modified sulfuric acid leached residue is investigated. It is showed that when the initial pH value of wastewater containing heavy metal ions including Pb(II), Cu(II), Co(II), Ni(II), Mn(II), Zn(II), Cd(II) and As(III) range from 1.4 to 1.9, with the use of the modified leached residue, As(III) ion can be selectively separated from wastewater, and the separation efficiency can reach 90%~100%. The adsorption efficiency is affected by pH, reaction time, amount of adsorbent and the initial concentration of heavy metal ions in wastewater. The results showed that the optimum pH was natural pH value and the absorption equilibrium time was 2 hours. The adsorption efficiency of heavy metal ions increases with the addition of adsorbent and de- creases with the increase of the initial concentrations of heavy metal ions in wastewater. The heavy metal ions polluted wastewater, of which concentration is about 22.5~793.6 mg/L, can meet the national disposal standard for industrial wastewaters in China very well, after 2 hours treated by 3.75~7.50 g/L modified adsorbent at room temperature. Standard methods were used to investaged investigate the absorption behaviour between abosorbentabsorbent and metal ions in the wastewater. It is concluded that the adsorption behaviour of Co(II), Mn(II) and As(III) ion fits Freundlich iso-therm, while the adsorption behaviour of Pb(II), Cu(II), Zn(II), Cd(II) and Ni(II) ions fits Langmuir isotherm, and the saturated adsorption amount of the modified adsorbent is about 54.0~336.7mg metal/g?adsorbentabsorbent. It is suggested that the modified sulfuric acid leached residue produced from oceanic cobalt-rich crusts is environmentally attractive and meaningful as absorbent used in heavy metal ions polluted wastewater.

Jan 1, 2014

By Indrajit Paul, Atanu Pal, Kapil Modi, Sanjay Chandra, Chandra Sekhar, Srinivas Dwarapudi

"High alumina content in the Indian iron ore fines (2.5% Al2O3) resulted in poor quality pellets at the recently commissioned 6 MTPA pelletizing plant and a study was under taken to establish suitable pellet chemistry through proper fluxing agents. Limestone fluxed pellets were prepared at varying basicity (0 to 0.8) and pyroxenite fluxed pellets at varying MgO contents (0 to 3%) to study their effect on the metallurgical properties. Fired pellets were tested for their strength, RDI, reducibility and swelling. Microstructural studies, optical and SEM-EDS, were carried out to quantify different phases and their chemistry. Acid pellets exhibited poor quality whereas limestone pellets at 0.8 basicity and pyroxenite pellets at 1.5% MgO exhibited optimum metallurgical quality. Formation of widely distributed silicate melt in limestone pellets and high melting point slag & magnesioferrite in pyroxenite pellets found to improve their quality. However during commercial production of MgO bearing pyroxenite pellets, their room temperature and low temperature properties found to be inferior, but exhibited better high temperature properties, viz. softening-melting behavior. Contrary to this, commercially produced limestone pellets, comprising CaO, exhibited better strength and RDI but showed poor high temperature properties. To yield the benefits of both CaO (for good strength and RDI) and MgO (for low swelling and high softening), a dual flux combination was established by using both limestone and pyroxenite/olivine together that resulted in optimum metallurgical properties. Coke rate at the blast furnaces found to be reduced by 1kg for every1% increase of dual flux pellets in the burden.INTRODUCTION Iron ore agglomerate quality plays a vital role in decreasing the reducing agent consumption and increasing the productivity of blast furnace. In most of the integrated steel works, the burden mix for blast furnace is decided as per the availability of the iron ore agglomerates like sinter and pellets. More attention has been given in recent years to the use of fluxed pellets in blast furnace due to their good strength and improved reducibility, swelling and softening melting characteristics. Generally, quality of pellets is influenced by the nature of ore or concentrate, associated gangue, type and amount of fluxes added and their subsequent treatment to produce pellets. These factors in turn result in the variation of physicochemical properties of the coexisting phases and their distribution during pellet induration. Hence properties of the pellets are largely governed by the form and degree of bonding achieved between ore particles and the stability of these bonding phases during reduction of iron oxides (Panigraphy et al., 1990). It is important to note that conditions and parameters of pelletizing are specific to given ore or concentrate; the present study is undertaken for typical Indian hematite ore fines high in alumina. Except authors earlier work on quality of pellets from Indian iron ore (Dwarapudi et al., 2008, 2010), there is no considerable literature reported on the effect of pellet basicity and MgO content in the basicity range of 0 to 0.8 for Indian hematite ore."

Jan 1, 2018

By K. B. Venkatesh

In view of the importance of size reduction operations from the energy consumption point of view, during the past one hundred and fifty years a number of attempts have been made to develop a general energy-size relationship. However, to date it has not been possible to clearly define the scope of application of various laws proposed, though Bond law has been widely used with a moderate degree of success. It was, therefore, decided to carry out a thorough analysis of the batch ball mill grinding data available in the literature on several minerals that were ground under normal range of operating conditions. In particular, relationships proposed by Bond, Kapur, Voller and Morrell were examined in detail. It was found that the relationship proposed by Kapur in terms of the mean particle size provided a more accurate basis for estimation of energy. The value of the exponent of mean particle size in this relationship, a, is same as the exponent of the particle size in the expression for the grinding rate parameter: ki = Axia, provided the particle size distribution range corresponds to the self-similar or self-preserving regime. In this regime, mean particle size is proportional to the 80 percent passing size and size modulus. From the practical application point of view, it was possible to describe the variation of µ1 over limited, but significantly broad size range, using a constant value of a. Thus, by carrying out a few batches, grinding experiments over the size distribution range corresponding to the contents of the production mill, the applicable value of a can be determined. Keywords: energy-size relationship, ball mill, mean particle size, self-similar size distribution regime

Sep 1, 2012

By B. P. Baruah

A good deposit of high sulphur coals of tertiary origin is existent in North eastern region of India. These coals are known to have indifferent characteristics in comparison to other Indian coals. The general Physico-chemical characteristics are low ash and high volatile matter, calorific value and sulphur content. Sulphur in these coals (70-95% of organic) is mostly affixed to the structure of the coal. Owing to the stringent environmental regulations, the utilization of these coals has severe limitations due to high sulphur content. In the present investigation, sulphur incorporation in to these coals has been discussed along with possible organic sulphur functionalities. The various desulphurization techniques carried out for removing sulphur from these coals have been discussed. Two step oxidative desulphurization processes has been found to be most efficient for organic sulphur removal along with mineral matter and potential toxic elements. Keywords: oxidative desulfurization, potential toxic elements, sulfur incorporation

Sep 1, 2012

By G. V. Sedelnikova

Biohydrometallurgical studies were performed on the sulfide gold-arsenic concentrate obtained in treatment of refractory ore from a deposit located in northern Russia. Gold is disseminated in sulfides-arsenopyrite, pyrite and antimonite (their content is 10.0%, 30.4% and 0.7%, respectively). Gold extraction is only 11.8% by cyanidation. Results are given for test bacterial oxidation of the concentrate in continuous mode at temp. = 28~32°C using mesophilic bacteria and at temp. = 32~38°C using the association including moderate thermophilic bacteria. The paper shows that the use of moderate thermophilic bacteria allows to speed up sulfide biooxidation and reduce its time to 96 hours compared to leaching at temp. = 28~32°C for 110~120 hours. The optimal range of pH = 1.5~2.0 of biooxidation process was determined where bacterial solutions are produced with the molar ratio Fe:As > 3 necessary for precipitation of hard-to-solve, environmentally safe arsenical precipitates. Electron microscopy showed that sulfide biooxidation results in liberation of disseminated gold with nanoparticle-level sizes. High sorptive activity of carbonaceous matter and other compounds of bacterial residues cause low gold extraction into cyanide solution ? 28.7%. 10% resin load makes it possible to extract 88.1% Au. Aeration of pulp in calcareous medium enhances extraction to 95.7% and decreases cyanide consumption from 17kg/t to 8 kg/t.

Jan 1, 2014

By I. Gombköto

In the EU-region, the automatically operated approximately 200 (rotating hammer) shredder plants processing large technical equipment (end-of-life vehicles, large household appliances) annually produces 8-9 million tons of non-metallic grinded by-product, which ends in landfills, without recovery. Although this by-product is organic material, still contains large amount of metal components worth recycling. These operations, such as shredding and processing end of life vehicles or mixed metal components are a growing market and it is become more potential if EU directive 2002/96/EC will become obligatory for new member and candidate countries and they have to apply EU regulations. Eddy current separators (ECS) are one of the most important units of separation of non-ferrous metals from insulators in waste recycling. The product of ECS processing of shredded ELV?s is usually a mixture of Al, Cu, Brass and stainless steel. This mixture has relatively low price on the market, while purified metal products are required by smelters for which shredder operators are able to get even higher price. Our aim at University of Miskolc was to find solution producing pure metal products using dry separation processes. Authors are presenting a possible solution, using ECS. Institute of Raw Material Preparation and Environmental Processing possesses an ECS, equipped with 305 mm wide belt, and a concentric magnetic rotor. The subject of our work was to investigate the behaviour of model particles with different shape, conductivity (aluminium and brass), orientation and size in order to separate Al and Brass. We used model particles with similar shapes of shredder plant originated ones. The magnetic flux and magnetic frequency was constant and derived by the design of the rotor. During our research work, belt speed and rotor speed of ECS were varied. The particle distance and trajectory caused by throwing was determined and the results are reported in this paper.

Sep 1, 2012