Search Documents

By L. Weitkämper

The big challenge at present and in the future is the economization of resources. This is applied for the whole industry but particularly in fields of mineral processing. The most important resources are energy and water. The shortage and price advance of energy is worldwide noticeable whereas the shortage of water is regionally limited at present. However due to the increasing world population, associated with a rising standard of living, water will become more and more important. Studies of the Unesco from 2001 indicate that the total water consumption raised seven times since the last 100 years at a growth of population of just three times. (UNESCO-Currier, 10/2001). This trend is going to be increased. While today more than 90 % of the humanity has access to clean water, in 2050 just about 50 % will be in the same situation. These figures indicate the importance of a gentle handling with the resource water. Further more the disposal of fine products, containing most of the water, is an environmental concern and in the future the mining and processing of raw materials will become important and necessary in desert, arid or permafrost areas. In these areas just efficient dry cleaning technologies will allow an economical beneficiation or better enable the processing at all. Most of the separation technologies with high throughput rates in mineral processing are based on wet processes. This applies especially for the separation of fines. Though there are some dry technologies available for the separation of coarse materials, like pneumatic gravity separation [air jigs and air tables], magnetic separation and not least sensor based sorters. Dry separation of fines is bounded mostly on cost intensive and low throughput technologies. The pneumatic separation undergoes at present a renaissance, mainly due to the development of the all air jig by the German supplier Allmineral. This newly developed sorting device yields good results in the separation of coarse to medium size material. All these facts and figures show the potential and motivation for developing an efficient dry separation device for fines. The following article delineates the development, performance and chance of a new dry separation technology for fines.

Jan 1, 2014

By S. F. Kaplan, A. S. Dolotov, V. N. Kovalev

"At this point in time, autoclave recovery (POX) followed by sorption cyanidation (CIL) is one of the most promising technologies for the efficient processing of refractory and double refractory gold-bearing sulphide rock. This hydrometallurgical technology requires the use of a large amount of water (up to 5 tons per ton of used concentrate), resulting in highly saline water with high pH (pH 9-11), high content of cyanides (up to 300 mg/l), arsenic compounds, antimony and a number of heavy metals. In order to determine the possibility of using recycling industrial water in POX-CIL technology, several batches of experiments were conducted (using the double refractory flotation concentrate of the Mayskoye deposit). Urban water with a chloride ion content of 10 mg/l was used during the reference POX-CIL experiment as the liquid phase of the ??? feed pulp. At that, gold extraction rate amounted to 89.4 %. A full cycle of POX(200 ºC)-CIL was carried out during the first part of the experiments; at that, fresh concentrate of the untreated recycling water with cyanide ion content of 95.4 mg/l, left after the completion of the previous CIL cycle, was used for repulping. It has been established that direct use of untreated recycling industrial water is impossible due to a sharp decline in gold extraction (preg-robbing) down to 79.5%. The presence of chloride ions, cyanide ions and other ligands in the liquid phase provides effective complexion formation for the recovery gold; complex gold compounds are quickly and firmly sorbed by the natural carbonaceous substances of the concentrate at the stage of autoclave recovery; they are virtually not cyanized onwards, and gold is carried over to the tailings. During the the second batch of experiments, recycling industrial water with cyanide and chloride ions' concentration of 500 mg/l each was subjected to the reverse osmosis desalination (up to 6 times in a successive order). After each desalting cycle, such water was used as the liquid phase of the feed pulp in POX-CIL. 6 cycles of RO desalination enabled the extraction of 86.1% Au (which is close to reference recovery). During the third batch of experiments, recycling industrial water was diluted with distilled water (2, 4, 16, 32, 64 times); after each dilution cycle, this water was used as the liquid phase of the POX-CIL feed pulp. Gold extraction after 64-fold dilution amounted to 82.6%. The results of the conducted researches show that the use of untreated recycling industrial water in POX-CIL hydrometallurgical technology is absolutely impossible due to a sharp decline in gold extraction. Even the 64-fold dilution with pure water is inefficient both from the perspective of gold extraction and of rational use of water. Reverse osmosis desalination solves the problem of water treatment except for the removal of cyanide ion, which requires separate reagent treatment of water."

Jan 1, 2018

By Y. Rama Murthy

Around 90% of the chromite resources of India are concentrated in the Boula-Nuasahi Sukinda belt of Orissa state. In order to conserve these valuable ore resources strategically, several companies established chrome ore beneficiation plants in this region. The general beneficiation process in these plants consists of gravity unit operations such as Floatex density separator, spiral, wet shaking table etc. Most of these gravity circuits suffer huge losses of valuable minerals in the tailing. Any attempt towards decreasing these losses would not only increase the limited reserves in India but also make the economics of the operations more attractive. Apart from the liberation phenomena, in many of the operating plants considerable quantity of values are lost in the tailings, due to inconsistent feed quality, inappropriate selection of operating and design parameters. Mineral engineers in this regard have to play a proactive and continuous role to improve the performance of all separating units by modifying even small changes based on tests conducted in laboratory under controlled conditions followed by attempts to make necessary changes in the plant. For such improvements, accurate data collection and proper data interpretation followed by making necessary change which is implementable in an operating plant play a very critical role in performance of the circuit. Databank collected over a period of time under various conditions would also help in overcoming the future problems related to either variation in the feed characteristics or specific demand by metallurgical industries. The above concept was adopted in one of the operating chromite beneficiation plant at Sukinda. The approach adopted and practical problems encountered during the study were reported in this paper. The result of trial campaign has shown that, an overall product assaying 30.2% Cr2O3 from the feed (18% Cr2O3 ) can be produced to in single stage. The final discards of the process contain 12% Cr2O3. Keywords: chromite, chromite beneficiation, chromite losses, gravity concentration techniques, plant operating data bank

Sep 1, 2012

By A. C. Maffei, M. V. Lins Gonçalves

Ore concentration processes are a function of the respective particle size distribution; however, most of them do not use an efficient operational method to determine it. From a practical point of view, the surface area can be calculated for any size analysis. The physical principles for determining the size distribution in each method are different, for the results will not be compared directly. During the development of the research project of the sulfide ore flotation method using inert gas, different methods for calculating the specific surface area have been used, such as sieving, sedimentation/X-ray, laser diffraction and BET, i.e. specific techniques to determine the specific surface area of copper and gold ore concentrates. The statistical method of minimum squares was used to achieve practical correlation equations among them. Regarding these two ores, if one knows a specific surface area value using one of the methods above, one can predict the result of the others. Diminution of the reagent consumption was so controlled and it could be even decreased by using inert gas.

Jan 1, 2003

By D. Tao

A novel rotary triboelectrostatic separator has been developed and patented recently at the University of Kentucky with unique features, including a high efficiency rotary charger, charger electrification, laminar air flow, etc. A parametric study has been performed with a coal combustion fly ash sample to investigate the effects of major operating parameters on the process performance. Most significant operating variables and optimum conditions were identified. Separation tests performed with four fly ash samples indicated that the rotary triboelectrostatic separator showed effective fly ash separation.

Jan 1, 2014

By R. Batterham

"The history of mineral processing is indeed long and has always been tied to mining methods of the day. While many new processes and devices have been developed, the most significant trend in recent times has been the ever increasing scale of operations. There is serious doubt this ongoing trend is enough to match the global trend of falling grades and rising energy demands needed for mineral processing. As well we see that globally, the social licence to operate for mining (and hence mineral processing) is far from secure. Indeed, some argue that mining as we know it is dying and in the future, mining will be much more environmentally secure, even to the extent of insisting upon “in place” recovery and only bringing to the surface the valued product. In this paper we comment on the ramifications of broader uptake of more sustainable mining for mineral processing methods and address the specific question of whether recent progress in in place recovery will lead to a timely breakthrough. The answer proposed is that this is possible in the next 10 - 20 years but in the meantime, the focus is just as likely to be on removal of waste much earlier in circuits. Either way, mineral processing as we know it will change significantly. INTRODUCTION Mineral processing has a long history well covered in a recent publication (Habashi, 2006) who points out “the ancient Egyptians knew already that it would be easier to melt an earth rich in gold particles than another which is poor. As a result, all efforts were made to enrich the gold by washing away the light gangue minerals. Similarly, another ancient method for enriching gold particles from a river stream was by means of fleece, hence the Greek myth of the “golden fleece”. Since the middle ages, striving for improved economics has driven a string of innovative developments in milling and separation. The reader is again referred to the informative and illustrative text by Habashi."

Jan 1, 2018

By H. Z. Liu

An extra-refractory gold ore in China belongs to Carlin Type Gold Ore which is not only submicroscopic but also rich in arsenic and organic carbon. They have been proved that its floatability is not good enough and the gold in the ore could not be leached almost if it was not pretreated. The tests for the ore were carried out in accordance with flotation-concentrate preoxidation-cyanidation(or CIL) processes in order to exploit the mine. Two new depressants were discovered in the flotation tests and improved concentrate grades from about 20g/t to 32~50g/t. The methods of the concentrate preoxidation tests were alkaline atmospheric oxidation, acidic atmospheric oxidation, acidic pressure oxidation, roasting oxidation?biooxidation. The cyanidation tests after the concentrate preoxidation have proved the gold extraction of the pressure oxidation to be the highest(92.5%) and that of roasting secondary(89.3%). After fuller techno-economic comparison, it is suggested that the flotation-pressure oxidation or roasting-CIL process should be the most optimal for treating the ore. The gold recoveries of the ore were 83% for the pressure oxidation and 80% for the roasting respectively.

Jan 1, 2014

By V. A. Chanturiya

In Pt- and Au-keeping complex ores processing, about 10% ~ 15% of noble metals are lost with true tailings that are due to low floatability of Pt- and Au-keeping minerals by the conventional collectors. With the aim to achieve the effective recovery of noble metals at flotation of Pt-Cu-Ni and Au-keeping ores organic complex reagents keeping electron-donating atoms of nitrogen, oxygen, sulfur or phosphorus may be offered as selective collectors for the indicated minerals. These rea-gents tend to form complex compounds with PGM. Besides this, Cu-Ni-Pt and complex Pt and Au carbonated mica ores are characterized by finely disseminated (up to nanometer size) mineral forms of Pt in multivalent states. In this connection, the use of a combination of the strong ionic collectors with nonionic reactants that are capable to derivate complex compounds with multivalent PGM seems to be expedient for this type of ores. In the research new complex reactants were tested such as cyclic alkylene-trithiocarbonates, oxyalkyl butylxanthogen acid ethers, a combination of the collectors ? mercaptobenzothiazole (MBT) and dialkyldithiophosphates (DTP). Sorption and flotation tests were made with monomine-ralic samples of chalcopyrite, pentlandite, pyrrhotite, pyrite, and Pt-Cu-Ni sulfide ore samples. Sorption properties were examined by the extractive UV spectrophotometric method and potentiometric measurements. To indicate a structure of modified xanthate solutions the method of a thin-layer chromatography (TLC) was applied. The chromatographic behavior of the basic components of modified xanthate solution ? ButX, cyclic propylene-trithiocarbonate (PTTC), diethyl-dithiocarbamate (DEDC) and the product of its modification ? oxypropyl-S-ether of dithiocarbamatic acid was studied on plates ?Silufol UV ? 254?. The composition of organic solvents and its ratio in a mobile phase was deter-mined for simultaneous chromatography of the main components of a reaction mixture. It was found that operating selectivity of MBT, DTP and cyclic alkylene-trithiocarbonates incorporated in modified xanthate in relation to Pt-Cu-Ni and Au-containing sulfide minerals might be explained by an electoral sorption of this nonionic collector on a surface of the minerals studied. It was demonstrated that the application new reagent modes with the use of a combination of designed complex reactants helped to increase the extraction index of Pt- and Au-keeping minerals from complicated ores.

Jan 1, 2014

By S. Castro, L. Gutierrez

"Mining operations are often located in remote arid environments with limited access to fresh water. Shortage of fresh water in such cases makes it necessary to use seawater in mineral processing plants. Such plants treating Cu- Mo sulfide ores in seawater have been fully operational in Chile (e.g. Las Luces, Centinela). In many cases process waters used in commercial flotation plants (e.g. Mt Keith in Western Australia) are even more concentrated electrolyte solutions than seawater. This paper is an attempt at classification of the flotation operations carried out in process waters that are concentrated electrolyte solutions.INTRODUCTIONAccording to Gleick (1966), of the total Earth’ water resources 97.5% is in the oceans and ice caps, and thus only about 2.5% is fresh water. Shortage of fresh water in many parts of the world makes it necessary to use seawater in mineral processing operations. The existing commercial operations using seawater as well as recent research projects that deal not only with sulfide ores but also with apatite ores provide a lot of information that can now be generalized. The progress that has been made in this area is reviewed and based on this information an attempt is being made at classifying the flotation operations carried out in highly concentrated electrolyte process waters.SALT FLOTATIONFlotation in highly concentrated electrolyte solutions was studied by Klassen (Klassen, 1963). He reported that hydrophobic, bituminous coals, could float in salt solutions without addition of any other flotation agents. The process is referred to as salt flotation. Other inherently hyhrophobic minerals (e.g. talc, graphite, sulfur, etc.) were shown to behave similarly (Klassen and Mokrousov, 1963)As Figure 1 shows, some coals float quite well in solutions of Na2SO4, NaCl and NaNO3 (Klassen, 1963). While there are differences between the tested salts (explained by different foamabilities of these solutions) all the tests indicate that only bituminous coals float well in concentrated electrolyte solutions. 0.3 M solutions are quite sufficient to initiate a good and very fast flotation. If wettability of various coals is compared it becomes obvious that these well floating coals are very hydrophobic bituminous coals (Figure 2)."

Jan 1, 2018

By G. Demi

Chromium ore exploitation has commenced in 1948 in Albania and there are produced about 24.3 million tons up to the end of 2006. Last years the prices and need were increased notably. Main export of chromium ores and concentrates was accomplished respectively 114 500 ton and 13 000 ton in People Republic of China during 2006 year. Location, status, reserves and grade of chromium deposits of Albania are presented in the paper. Chromium ore enrichment is related with their composition and Cr2O3 content, as well as with market requests. Actually, high grade chromium ores with Cr2O3 content over 38% ~ 40% are directly exported or treated in metallurgy, but last time have been exported and chromium ores with 28% ~ 30% Cr2O3 content for the reason that dressing plants can not be operated for investment lack. High grade chromium ores have been treated in heavy media separation plant before 1990. It is presented flow sheet, figures and necessity to put in operation HMS plant in the paper. Actually, low grade chromium ores with content 16% ~ 20% Cr2O3 are not enriched for the lack of investments, but before 1990 they have been concentrated in dressing plants producing chromium concentrates grade 48% ~ 50% Cr2O3. In the paper are shown technological schemes and industrial figures during more than 20 years operation and possibilities to reconstruct these mineral processing plants. Only chromium mineral processing plant of Bulqiza is in operation using as raw material its old existing tailings. The flow sheet and figures show that are possibilities to increase recovery and grade of concentrate in the plant. Separation and concentration of slimes in suitable equipment gives visible improvement of Cr2O3 recovery. Several tests have been carried out with flotation and magnetic separation methods for enrichment of low grade chromium ores. Flow sheet and figures of mineral processing ores content olivine as gangue mineral are interesting, because combination of gravimetric with magnetic methods is necessary in this case. In the paper are presented the tests and good results of low chromium ore pre concentration. Metallurgical treatment of chromium ores to produce Ferro chrome, as well as technological process, figures, consume of electrical power and materials in Elbasani and Burreli furnaces are shown and necessary investments to treat in metallurgy all produced chromium ores in Albania are considered.

Jan 1, 2014

By Markus A. Reuter, Jacques J. Eksteen

The modelling of bath type furnaces tends to be either fundamental in nature or total empirical "black box models". While models of the first kind are robust, they tend to lack accuracy, in cases where they are to be used for process control, and may take an overly long in development time. On the other hand, black box models tend to lack robustness of prediction for all circumstances and tend to be limited to interpolate based on historical data. While this may very often provide short-term accuracy, the models may have problems with stability in the long term. Moreover, the model structure may not reflect any of the fundamental properties of the system and remains opaque to fundamental analysis. The aim of the model development is in obtaining a model that have robustness, high accuracy, a short development time and which is adaptive to a changing environment. The models are specifically developed for on-line decision support or control of furnaces. The modelling approach is evaluated for a chromite bath smelting furnace. The role of systems analysis, mass balance smoothing, thermodynamic analysis are integrated into one generic algorithm for bath type furnaces. Therefore, this paper argues that to understand complex metallurgical furnaces a hybrid approach is the only method to fully grasp the intricacies of metallurgy, to improve operations, economics as well as environmental performance.

Jan 1, 2003

By H. J. Wu

The optimum performance in mineral processing plants usually demands the optimum size reduction, which is frequently achieved by a closed grinding circuit. Due to the difficulty associated with fine size classification, the size separation efficiency in closed grinding circuit is usually very low, which leads to huge circulating load and significant overgrinding. Recent development of Der-rick Stack Sizer has made an efficient fine size separation down to 200 mesh with a satisfactory screening capacity. With the efficient fine size separation with Derrick Stack sizer, the problems commonly associated with typical closed grinding circuit, including high circulating load and over-grinding, have been eliminated. Feedback from numerous Stack Sizer applications in iron ore industry indicated that, compared with conventional fine size classification equipment, the circulating load achieved by Derrick screen was usually decreased from approximate 300% down to 60% or so, while the iron recovery has been increased by 6% to 8% only by more efficient size separation in the closed grinding circuit. To study this phenomenon, this paper discusses the relationship between size classification, circulating load and mineral recovery in the closed grinding circuit. A simulation model to predict the improvement in the grinding circuit from more efficient screening is also introduced with this paper.

Jan 1, 2014

By Josefin Lannefors, Anders Klingberg, Natalija Gorochovceva

"Development of new anionic collectors becomes more and more important. This can be explained, on the one hand, by the fact that over the years phosphate ores have become more fine grained and complex (example weathered). On the other hand, a development with a focus on sustainability (sustainable development) of new anionic surfactants is required by authorities and society. Within the sustainable development several characteristics of a collector have to be taken into an account: efficiency, selectivity, froth characteristics, environmental profile, raw materials used for the synthesis, manufacturing complexity, stability upon storage, etc.Several anionic surfactants based on ester and amide chemistry were synthesized, characterized and used as flotation agents for calcium phosphate containing ore. The surfactants were used in a formulation together with other anionics, since in a pure form, during the flotation, they did not provide right froth characteristics.A new anionic collector/formulation was developed, that fulfills all above listed requirements."

Jan 1, 2014

By T. Bhambhani

Research at Cytec over the past two decades has shown that the traditional approach for ore metallurgical characterization (typically conducted via laboratory-scale batch flotation tests), which involves changing reagents and conditions one-factor-at-a-time, leads to several pitfalls. The chemical solution thus selected has a narrow un-optimized window of performance and will likely fail in the plant. A holistic approach, called the Flotation Matrix 100? process for ore metallurgical characterization, was developed at Cytec about a decade ago and has been successfully used to develop robust reagent solutions for several operations around the world. The premise for the approach is that flotation outcome from ores is variable and is determined by complex interactions between various physical, chemical and operational factors. A key component of the process is the use of efficient multivariate designs focused on the chemistry aspects (reagents and pulp chemistry), which helps identify the best processing conditions for each ore type, as well as the conditions resulting in poor performance. It also includes advanced statistical methods for dealing with the complexity and variability of experimental data. The holistic approach is illustrated in this paper with a case study on Pb/Zn ores. Using just 18 carefully designed batch tests, it is possible to partially simulate the behavior of each ore type in the plant. The best conditions for each ore type, along with the conditions to avoid, are identified. Along with this, insights are obtained into the reasons for high reagent dosages for certain ore types, and interactions between variables. Keywords: flotation, holistic approach, metallurgical characterization, multivariate experimental designs, base and precious metals recovery, sulfide collectors and modifiers, Pb/Zn sequential flotation

Sep 1, 2012

By Kal Sastry, Anshuman Prasad

This paper presents a population balance model (PBM) for describing the agglomeration process and select a suitable coalescence kernel that can simultaneously describe nucleation, layering and coalescence mechanisms. The PBM is solved numerically by making use of a size discretization procedure in order to simulate iron ore agglomeration in rotating drums where moist feed is added to preformed seeds. Subsequently, a comparison of computer simulation results with the previously published experimental data is provided. Finally, the paper discusses how the current approach can be further extended to the simulation of industrial iron ore agglomeration circuits operated in closed circuit.

Jan 1, 2003

By D. M. R. Sekhar

Certain types of rock phosphates of sedimentary origin are applied to acidic soils as fertilizer directly. Recent research in India showed that high grade rock phosphate in fine size when used as a mix with organic manure works as efficiently as di-ammonium phosphate (DAP) in alkaline soils. The rock phosphate from Jhamarkotra, India (sedimentary origin), Egypt (sedimentary origin) and South Africa (volcanic origin) showed good agronomic efficiency when used as Phosphate Rich Organic Manure (PROM). Further PROM shows equal residual effect. The results of efficiency of PROM made using two grades (+ 24% P2O5 and 34% P2O5) of rock phosphate mineral from Jordan show that low grade rock phosphate slimes are as effective as high grade phosphate concentrate when used in PROM. Also PROM is very effective in the saline soil of Eshidiya desert where DAP is not at all effective.

Jan 1, 2014

By V. A. Masloboev, A. V. Svetlov, D. V. Makarov

"The methods of heap leaching are considered to be the most promising for the low-grade copper-nickel raw materials. The article presents intensification capabilities of the process. Objects of research: the low-grade copper-nickel ores of Moncheplutone deposits (Moroshkovoye Lake, Nyud Terrasa, Nittis-Kumuzh’ya-Travyanaya (NKT), as well as the copper-nickel ore dressing tailings of the “Kola MMC” JSC. The following directions for the intensification of the low-grade copper-nickel raw materials heap leaching have been considered: preliminary electric pulse destruction (EPD) of ore; ore crushing and further sulfuric acid agglomeration. The impact of sulfuric acid concentration (1-3%) on the extraction of non-ferrous metals kinetics from the copper-nickel ore dressing tailings under various conditions of the percolation leaching has been studied. INTRODUCTION The low-grade grade sulfide ores at the abandoned and producing deposits, overburden rocks, mill tailings and non-ferrous slag are thought to be one of the large-scale sources for non-ferrous metals, on the one hand. On the other hand, they are known to be the subjects of emergency environmental danger. For this reason, the use of mine dumps and tailings, as well as the remained ores left in the ground as raw products, and at the same time decreasing the load on environment, are considered to be the pressing ecological and economic issue (Chanturia et al., 2012). Methods of heap hydrometallurgical and bacterial leaching are sure to be potentially productive for processing such low-grade and technogenic raw materials (Petersen, 2016). The early studies of hydrometallurgical method possibility to process copper-nickel ores of the Murmansk region deposits were launched in the seventies of the previous century (Golovko et al., 1978). For referencing purposes, the main types of impregnated ores from the deposits Zhdanovskoye, Kaula, Sopchinsky Plast and Lovnoozerskoye were selected. The metal content varied, as %: 0.46-1.49 of nickel, 0.01-0.62 of copper. In the first experiments, the solution containing 150g/l of H2SO4 and 135g/l of NaCl, was used in the capacity of leaching reagent. The possibility of underground metals leaching from the ores of the Lovnoozerskoye deposit was justified due to the performed laboratory and further large-sized tests."

Jan 1, 2018

By Xiong Dahe

In recent years many creative technologies are applied to SLon vertical ring and pulsating high gradient magnetic separators. SLon-2500 and SLon-3000 vertical ring and pulsating high gradient magnetic separators are created towards larger scale. Through optimizing the magnetic system and lowering the electric current density, their energy consumption is obviously dropped. New magnetic matrixes are developed to raise the beneficial efficiency of valuable minerals. Special SLon vertical ring and pulsating high gradient magnetic separators are developed which can treat coarser particles of 0-5 mm. Through these technology creations, the mineral processing efficiency of SLon magnetic separators is further raised and their processing cost dropped. Therefore, they have been found wider applications. SLon-2500 applied in Essar Steel of India. In 2007, Essar Steel did a test on its Kirandul hematite ore with SLon magnetic separator and got very good results. The feed grade is 59.77%Fe, after SLon one roughing and one scavenging, the total iron concentrate grade is 65.00%Fe and iron recovery 93.86%. In 2008-2010, the company bought 10 SLon-2500 magnetic separators to treat such iron ores. In 2010 the first SLon-3000 was applied to processing ilmenite. The magnetite-ilmenite deposit is located in Pan Zhi Hua, Si Chuan Province of China. The ore processing flow sheet is: Drum low intensity magnetic separator is used to take out magnetite, and then the SLon-3000 is used to recover ilmenite for roughing. The mags of the SLon-3000 are further cleaned by flotation. The SLon-3000 average operational results are: feed grade 9.52%TiO2, mags grade 17.43%TiO2, mags mass ratio 41.01%, TiO2 recovery 75.09%, non-mags grade 4.02% TiO2, non-mags mass ratio 58.99%. SLon magnetic separators Applied to treat 0-5mm limonite: The feed of SLon magnetic separator is usually 0-2 mm which needs to be ground by ball mill. As many Chinese iron ores are poor grades, if we can throw part of tails before grinding, the grinding cost will be greatly reduced. In 2010, a SLon-1500 and a SLon-2000 were specially built to treat 0-5 mm limonite. The feed grade is 26.51%Fe, mags grade 53.20%Fe, iron recovery 64.26, and tails grade 13.66% Fe. SLon-2500 applied to purify quartz. In 2009, a SLon-2500 magnetic separator was applied to purify quartz in Shan Xi province. Its feed is 0-1mm quartz which contains 0.15%-0.25%Fe2O3, the designed non-mags grade need to be less 0.08% Fe2O3. The production results of SLon-2500 non-mags are 0.05-0.06% Fe2O3, much better than the designed data. SLon applied in Si Jia Ying Iron Mine to recover hematite. Si Jia Ying is a big oxidized iron mine located in He Bei Province of China. In 2005-2010, a plant annually treating 10 million tons of oxidized iron ore was built in which 39 SLon magnetic separators are applied. The total flow sheet results are: Feed grade 30.44%Fe, iron concentrate grade 66%Fe, iron recovery 80%Fe, tails grade 9.65Fe%. SLon applied to recover specularite. Li Lou Iron Mine in An Hui Province of China built a plant annually processing 5 million tons of iron ore in 2010-2011. 25 SLon-2000 magnetic separators are applied to recover specularite. The total flow sheet results are: Feed grade 31.65%Fe, iron concentrate grade 65%Fe, iron recovery 80%Fe, tails grade 10.37%Fe. SLon applied in Da Hong Shan Iron Mine. Da Hong Shan Iron Mine is located in Yun Nan province of China. It treats 4.5 million tons of oxidized iron ore annually. 15 SLon-2000 magnetic separators are applied to recover hematite. The total flow sheet results are: Feed grade 35.61%Fe, iron concentrate grade 64.95%Fe, iron recovery 74.08%Fe, tails grade 15.55%. Keywords: SLon magnetic separator, iron ore, ilmenite, quartz, beneficiation

Sep 1, 2012

By P. Vijay Kumar

Phosphate minerals are conventionally concentrated by flotation process using soap or soap- light diesel oil emulsion as collector. Some plants use detergents such as sodium petroleum sulfonate or alfa olefin sulfonate to enhance efficiency of soap flotation. It is reported that urea a known hydrotrope enhances flotation efficiency of soap as efficiently as alfa olefin sulfonate or linear alkyl benzene sulfonate at bench scale tests. In the present study tri sodium citrate also a known hydrotrope is tested as promoter in the flotation of phosphate mineral from Eshidiya ore.

Sep 1, 2012

By Z. S. Abisheva

Rare and rare earth metals use quite often is an indicator of national economy development. The world structure of the rare-earth metals manufacturing countries in 2015 was presented as follows: China – 94.2%, India – 2.0%, Russia – 1.8%, the USA – 1.2%, Brazil – 0.5%, Malaysia – 0.3%. In Russia, large reserves of rare-earth metals, which reach nearly 28 million tons, are revealed. Kazakhstan, possessing a raw materials source of rare-earth metals, has all prerequisites for development of branch. Rare metals are manufactured in Kazakhstan incidentally by non-ferrous metals production. The production of indium, thallium, cadmium, selenium, tellurium, bismuth is made at the Ust-Kamenogorsk lead plant; tantalum, beryllium, niobium and molybdenum – at the enterprises of “National Atomic Company Kazatomprom” JSC. Production of a titanium, magnesium and vanadium is adjusted on “Ust-Kamenogorsk Titanium-magnesium Plant” JSC. Capacities for beryllic production yield are available on “Ulba Metallurgical Plant” JSC. The main producer of perrhenic production and osmium-187 is "Zhezkazganredmet" RSE. The single producer of gallium in Kazakhstan is “Aluminium of Kazakhstan” JSC; the capacity of enterprise is 25 t a year. In Kazakhstan innovative technologies for rare and rare earths mineral raw materials processing are created. The technology has been developed and a vacuum distillation apparatus has been created to purify crude selenium, which makes it possible to obtain a metal with a main component content of 99.9-99.99%. Technologies for processing of technogenic wastes and byproducts of the copper industry are developed. Implementation of technologies allow to obtain ammonium perrhenate, perrhenic acid, osmium isotope -187, tribasic lead sulphate, silver-concentrate. The technology of complex processing of black shales of Balasauskandyk deposit with the production of gold, vanadium, rare earth elements, uranium and ferrosilicon has been proposed. The processing was carried out using methods of autoclave leaching, sorption, extraction, precipitation. A highly profitable sorption technology for recovery of rhenium from solutions of underground leaching of uranium ores containing 0.2-0.4 mg/L of Re has been created. The organization of ammonium perrhenate production from solutions of uranium ore will significantly increase the volume of its production in Kazakhstan.

Jan 1, 2018