Search Documents

By L. Stamenov, H. Bouzahzah, S. Gaydardzhiev, D. Naumov

"The Chelopech epithermal arsenic bearing high-sulphidation, copper-gold deposit located in Bulgaria is often referred as the richest European gold deposit currently under exploitation. Key points from the flotation circuit of the processing plant have been sampled and selected physicochemical parameters measured. Plant survey has followed with selected samples being submitted to chemical and mineral liberation analysis (MLA). Quantitative analysis has enabled to link the flotation response of the main copper bearing minerals with the physiochemical parameters (Eh, DO, EDTA extractable Cu and Fe) being measured. Data from mineral liberation analysis have highlighted an important process-relevant information explaining the variable floatability in the various granulometric classes.The low chalcopyrite recovery could be linked to the non-sufficient amount of dissolved oxygen measured in the copper selective flotation circuit. Given the finely-disseminated copper bearing minerals, the observed copper losses inside the flotation could be also explained by the insufficient degree of liberation of the mineral grains. Suggestions for improvement in metallurgical recovery are therefore proposed.INTRODUCTIONThe Chelopech deposit is a high sulphidation (HS) volcanic-hosted epithermal gold-copper one (Bonev et al., 2002; Kouzmanov et al, 2009; Strashimirov, et al. 2002). It is considered as one of the largest and economically most important ore deposits in Bulgaria, and often is referred to Europe’s largest currently mined gold resource. It is located in the Srednogorie zone which falls within the central sector of the extensive Tethyan–Eurasian copper belt formed during Mesozoic–Cenozoic time along the southern margin of Eurasia. The Srednogorie zone has the features of a subduction-related, Late Cretaceous island arc, with development of a calk-alkaline to sub-alkaline volcano-plutonic magmatism and associated hydrothermal ore deposits (Bonev et al., 2002).Ore mineralisation occurs as veins, mineralised breccia, and massive sulphide replacements and disseminations. Three mineralisation stages have been identified at Chelopech deposit. An early pyrite–marcasite mineralisation (stage I), characterised by disseminated to massive pyrite followed and partly brecciated by enargite– luzonite and tennantite–chalcopyrite–bornite (stage II) mineralisation. The gold is met in ores belonging to the stage II. Sphalerite and galena veins characterise stage III, best developed below and adjacent to the pyrite–enargite– chalcopyrite ore bodies. Advanced argillic altered volcanoclastic rocks commonly host this mineralisation (Chambefort and R. Moritz, 2014)."

Jan 1, 2018

By G. Venkateswara Rao

The jigging of ferrous ore to produce higher-grade products has been practiced for many decades. This is due to easy separation, a beneficial trade- off between operating cost and reduced yield relative to Dense Media Separation (DMS). Jigging becomes prominent for beneficiation of iron ores in the coarser size range. At present drive is towards the use of under bed air pulsed jigs for the beneficiation of ferrous ores. The main advantage is that the under bed air pulsed jigs are capable of generating the large pulse of amplitudes required to fluidize a deep bed of heavy ores particularly lump iron ore up to 40mm size. The major jig parameters effecting the jigging operation are bed height, shape of the pulse, residence time, operating pressure, valve cycle time and water flow rate. With the pulse shape set correctly for optimum stratification rate, even it is still necessary to provide enough residence time, to ensure the difficult material will take time to migrate to the expected layer in the bed. In order to find the Jig Stratification Index (JIS) parameters like bed height, operating pressure, water flow rate, cycle valve time and shape of the pulse were optimized first by conducting various tests. Typical Iron ore samples from Odisha (both lump and fines) were subjected to stratification studies at residence time of 1, 5 and 15 minutes. Jig Stratification Index (JSI) for both lump (0.30) and fines (0.20) were determined by using APIC Jig. The maximum possible JSI was calculated by using heavy liquid separation test (0.42 for lump and 0.24 for fines). It is found that the jig bed JSI is less than the Heavy liquid JSI for both lump and fines. The ratio of Jig bed JSI to the heavy liquid JSI is 0.83 for lump and 0.71 for fines. The JSI and ratio of Jig bed JSI to Heavy liquid JSI are low for fines due to fluid turbulences causing some degree of remixing in the jig bed. The fluid turbulences are more for fines than lump, hence jigging of fines is difficult and challenging. Keywords: sub grade iron ore, gravity separation, jigging, apic jig, stratification, residence time, jig stratification index

Sep 1, 2012

By Paulo Sérgio de Oliveira, Joaquim D. Donda, Andreia C. Rosa

"The search for energy efficient technologies for comminution processes is constant in mineral processing studies, since those processes represent a major percentage of operational costs. In this context the use of stirred mills is increasing, especially for ultrafine grinding. Although many authors claim that these new equipment are more efficient than the conventional ball mills, there were very little chances to prove that in a practical way, since there are few industrial circuits where those technologies perform the same duty. Therefore, the regrinding circuit of Germano second concentrator offers an interesting opportunity: a vertical mill operating in parallel with two ball mills. During almost two years of operation, several sampling campaigns were conducted to evaluate the vertical mill performance and to compare the operational data of the three mills. The industrial data was also compared to jar mill tests results, which are monthly conducted in Samarco labs in order to predict the specific energy consumption required by the ore fed to these circuits. The vertical mill demonstrated the same ability to achieve the product specifications of the ball mills while proved to be able to reduce the medium specific energy consumption in about 40%."

Jan 1, 2014

By E. Pourjenaei, P. Ghobadi

High Pressure Grinding Roll (HPGR) is efficient equipment in comminution process. HPGR could be a good option for preparing ball mill feed at the first stage of grinding due to its high efficiency and low energy consumption. Closing with a screen, these mills are utilizing as one of the principle parts in mineral processing industries, especially for iron ores. Recently, HPGRs are working as primary mills at 4 developing lines in Gol-e-Gohar Iron Ore Processing Complex, Iran. Different mechanism of particle crushing in compare to the other tumbling mills makes the HPGR as certain equipment with its own particular controlling parameters. Hydraulic pressure, roller speed and level of material inside feeding hopper are the most important variables influencing grinding efficiency of the HPGR. To figure out how they impress the process and operation situation, different industrial tests were carried out and the best result (d80 about 8 mm for HPGR discharge) was achieved at 180-190 bar pressure (P), 300 rpm speed (S) and 50% of hopper level (L). It is worth noting that this finding has been observed through past pilot test too. We also used design expert method (DX7 software) to develop the best design and analysis the test results, as well. According to the mechanical restriction of HPGR and process limitation in the plant (based on the industrial results), we adjusted value of each parameter in a logical range. Therefore, 20 industrial tests were conducted, as DX7 recommended, and the various impacts of the parameters and their interaction were identified based on statistical analysis. As the authors expected, it was revealed that after presser, roller speed is a critical variable because of its significant role in residence time of the particles between the rollers. The function below has been determined to explain the relation between different parameters and the response.

Jan 1, 2018

By Y. P. Lu

PET/kaolin nanocomposites were prepared with melt blending and the structure of the composites was characterized through IR techniques. The results showed that there is stable chemical bonding between PET and kaolin. In addition, the dispersion condition of nanokaolin was observed by means of SEM and TEM. As a result, the thickness of the dispersed nanokaolin particles in PET matrix is mainly from 20mm to 200nm, and the nanosized particles congregate to some extent in the samples. In addition, it was found the kaolin particles almost homogeneously dispersed in the PET matrix, without preferential orientation because of the shear effect due to melt blending. Furthermore, the mechanical properties of PET/kaolin nanocomposites are dependent on the modification efficiency of nanokaolin. With the poor efficiency, the nanokaolin particles tend to aggregate at a high content and have a bad interfacial compability between nanokaolin and PET matrix, which lead to stress concentration, so the mechanical property descends. Experiments of different contents of modified nanokalin indicated that the intensity of PET/kaolin nanocomposites decreased firstly, then increased, and then decreased, with the nanokaolin content of 4 to 5 percent, the rupture stress of the composites showed a maximum value, which was higher than that of pure PET. On one hand, nanokaolin decreases the function among PET macromolecules, which will decline the mechanical properties, on the other hand, the piece structure of kaolinite improves the intensity of the nanocomposite. When the nanokaolin content is low, the former has the dominant effect on mechanical property, while the latter will play a leading role with the content increasing. But if the nanokaolin content still increases, the agglomeration and stress concentration will be obvious.

Jan 1, 2014

By Ricardo Montero

At this time, over 300 tons of Au are used in electronic equipment each year with other precious and strategic metals such as Ag, Pt, Pd, Cu, Nb, Ta, etc. After the use-phase, the electronic devices become electronic waste (e-waste); consequently it is important to consider e-waste as a secondary supply for recovery of these metals. One of the most important components is the printed circuit boards (PCBs) because the amount of their precious metals is ten times higher than rich precious metals bearing ore. This paper presents the recovery of Au, Ag, Cu and Nb from PCBs of discarded computers using leaching column technique. The amount of these metals in used PCBs was: 613 g/ton of Au, 1515 g/ton of Ag, 36 g/ton of Nb and 23.4 % of Cu. The PCBs were crushed with a hammer mill until reaching a particle size between 3.33 mm to 0.43 mm. Then, it was leached with sodium cyanide solution in a glass column using the following conditions: sodium cyanide concentration 4 g/L, flux 20 L/kg PCBs day, pH between 10.5 to 11 and leaching time 15 days. Every day, after leaching, the pregnant solutions passed through a column with activated carbon to complete the closed loop system. The following recoveries were obtained: 46.6% of Au, 51.3% of Ag, 47.2% of Nb and 62.3 % of Cu. The products obtained are: a) loaded carbon that contains the desired metals and b) processed PCBs with precious metal contents. A preliminary technical-economic study shows the feasibility to create a small-scale PCBs recycling plant. The initial investment is on the order of US$ 155 639, considering the recovered metals from loaded carbon. The internal rate of return for 10 years period (IRR) and net present value (NPV) estimated are 27% and US$ 105 926 respectively. Keywords: printed circuit boards, recovery, precious metals, niobium, leaching column

Sep 1, 2012

By V. Panayotov, M. Panayotova

"Wastewater from ores processing is often polluted by molybdate and sulfate (SO42-) ions. Sorption is one of suitable methods for removing those pollutants when presenting in low concentrations. This work reports results on adsorption of sulfate and molybdate ions on metal modified (with barium - Ba and lead - Pb) and organic reagent modified (with Hexadecyl-trimethyl-ammonium bromide - HDTMA) clinoptilolite. Zeolite’s modification with Pb, Ba and HDTMA increases its uptake capacity with respect to Mo(VI) at pH 3, with the uptake capacity decreasing in the order CL-Pb > CL-HDTMA > CL-Ba. Lead-modified clinoptilolite shows high uptake with respect to Mo(VI) in acidic, neutral and slightly alkaline conditions. The presence of SO42- in concentrations twice higher than the amount of Mo(VI) do not interfere with the Mo(VI) removal by CL-Pb. Zeolite’s modification with Ba and Pb renders it able to immobilize SO42- from water in the pH range 3-9. Kinetics of the uptake process is best described by the pseudo-first order kinetic equation. Increasing the initial concentrations of Mo(VI) and SO42- increases the removed amount of pollutants. INTRODUCTION Wastewater from copper-molybdenum ores processing is often polluted by molybdate and sulfate ions. Molybdenum (Mo) migrates easily in water and consequently the Mo polluted areas could extend for hundreds and thousands of meters (Ryzhenko, 2010). Molybdate anion is the only Mo(VI) species in natural water, i.e. at pH > 6.0. Its median freshwater hazardous concentration affecting 5% of the species (HC 5.50%) is 38.2 mg Mo/L (De-Schamphelaere et al., 2010). The marine water chronic toxicity (HC 5.50%) is assessed at 5.74 mg Mo/L (Heijerick et al., 2012). The predicted no-effect concentrations (PNEC) are 12.7 mg Mo/L and 1.92 mg Mo/L correspondingly for freshwater and marine water (Heijerick et al., 2012a). When sulfates present in drinking water in excess of 250 mg/L they cause a cathartic action (especially in children) in the presence of sodium and magnesium, and when the concentration exceeds 600 mg/L, diarrhea. When sulfate-rich effluents are discharged into the environment, they may increase the acidity of water bodies and soils (Guimarães and Leão, 2014). Because of the adverse effects to human health and the environment, limits are set for SO42- concentrations in waters and wastewaters in the range of 250 / 500 mg/L."

Jan 1, 2018

By C. V. G. K. Murty

Sillimanite, chemically named Aluminum silicate, 3Al2O3SiO2 is one of the three forms of alumino silicate polymorphs and commonly encountered in aluminous metamorphic, plutonic, and volcanic rocks and their weathering products. Most of the sillimanite deposits are granular and are of high grade available in coastal areas as associated mineral along with Titanium bearing minerals namely ilmenite, rutile etc. Sillimanite is one of the widely accepted raw materials for the manufacture of high alumina refractories (55-60 % alumina) or bricks. Sillimanite based refractory bricks are used for the lining of Blast furnaces, Arc furnaces, Soaking pits, Reheating furnaces of iron and steel, rotary kilns for cement manufacturing and general kilns for lime production. Considering the vast potential of unexploited sillimanite reserves in India, M/s Trimex Sands Pvt. Ltd., (TSPL)has set up a Mineral Sand Processing plant in 2010 at Andhra Pradesh with a capacity to produce about 50,000 tons of sillimanite per annum besides the production of various heavy minerals such as ilmenite, rutile, zircon and garnet. Traditionally in India, sillimanite is upgraded by froth flotation technique using Oleic acid as a collector cum frother, sodium silicate as depressant and soda ash as pH regulator. At TSPL, Conventional mechanical float cells are installed to float sillimanite. In addition to the usual problems associated with conventional cells, poor flow ability of the sillimanite concentrate is experienced in dry circuit due to the presence of sodium oleate. Fine garnet in the sillimanite concentrate contributes to high iron content in the final product, making sillimanite separation a nightmare for operators (lower recoveries coupled with inferior grades). Various efforts were made to improve the performance of the circuit such as introduction of additional frother like MIBC, optimizing the operating parameters such as pulp density, collector dosage, depressant dosage, air flow rate, pH etc., use of collector aids, stage wise addition of reagents etc. The challenges faced to produce a sillimanite product with stringent quality norms and the efforts made to improve the grade and recovery are described in this paper. Keywords: sillimanite, froth flotation, conventional mechanical cell

Sep 1, 2012

By Stephen Gay, Dewetia Latti

"When improving a plant a mineral processing engineer would like to know the mineral composition distribution. In order to assess this distribution in particles, as compared to the corresponding distribution in particle sections, a procedure needs to be applied to the observed particle sections. Such a procedure is called a stereological correction. There exists many stereological correction procedures, but one group of such procedures is based on using those stereological equations that do not require making assumptions regarding particle shape or texture.In particular Davy derived an equation to estimate the covariance of mineral composition distributions for particles from both particle sections and linear intercepts. Furthermore, this covariance can also be used to measure the variance of the composition distribution of each mineral.This paper shall present results verifying this equation. The experimental method was based on obtaining particle information from serially-sectioned particles. Particle samples selected for serial sectioning displayed a range of natural textures including liberated, binary and composite particles. The exposed surface of the polished sections were analysed using QEM*SEM. This procedure was repeated until all of the grains have been polished away. The covariance of mineral distributions were calculated from the serial sections and compared with that calculated using Davy’s equation."

Jan 1, 2003

By Y. F. Guo

Among the different valences of vanadium, V (?) is insoluble in acid, V (?) and V (?) is in-soluble in water but soluble in acid. Vanadium mainly exists as V (?) in vanadium titanium-rich material obtained by reduction -milling-separation from vanadiferous titanomagnetite. Therefore, the vanadium titanium-rich material can not be used to extract vanadium by acid directly. In this paper, the vanadium leaching was studied by oxidation roasting and acid leaching. Through oxidation roasting, vanadium is transformed from the insoluble V (?) into V (?) or V (?) in order to improve the leaching of vanadium. The results show that vanadium leaching increases significantly by oxidation roasting-acid leaching. Leaching of vanadium is up to 70.18% under the optimized conditions of roasting temperature of 950 ?, roasting time of 40 min, sulfuric acid concentration of 40%, leaching time of 4h, leaching temperature of 95 ? and liquid to solid ratio of 4 : 1.

Jan 1, 2014

By H. Z. Kuyumcu

Coking of coal blends using high volatile coals with poor coking abilities to produce a high quality coke for blast furnace application can be achieved by compacting the coal blend prior to the carbonization process. Here densification up to a relative material density of 80 %, i.e. a compact density around 1100 kg/m3, has proven to be advantageous. Coal is compacted by stamping, if the so-called stamp charging process applied. Compacting of the coal by pressing is practised in case of the cokemaking with so-called heat-recovery ovens. Stamped and pressed coal cakes require over the cake volume uniform high density and mechanical stability. Besides the aspects of the coal selection, the efficiency of the process is mainly determined by the operating parameters compacting time and compacting energy for coal cake making. At the Department for Mechanical Process Engineering & Solids Processing of the Technical University Berlin the two sub-processes of densification and strengthening during stamping and during pressing are theoretically and experimentally investigated using specially developed lab-scale compacting test units and a strength test device. Describing cake density in terms of coal properties for a given coal and measured compacting energy input then leads to a compacting equation with the so-called Stampability as the integral model parameter for the stamping process. For the pressing process the cake density can be calculated with the measured compacting pressure and the Compressibility factor, respectively. Investigations were carried out to provide evidence of a significant influence of coal type, coal surface moisture, coal granulometric and mechanical properties on the densification process. The overall objective of the work is to establish a comprehensive mathematical model on the compacting behavior of large coal bulk quantities and the optimization of the compacting processes by stamping and by pressing. Keywords: coal compacting, agglomeration, stamping, pressing, cokemaking

Sep 1, 2012

By G. J. Mei

Separation of hematite and iron-containing silicate gangue - aegirine by Flotation using fatty acid collector and (NH4)2SiF6 depressant was investigated in this paper. The flotation tests with single minerals show Ammonium hexafluorosilicate (AHFS) is a selective depressant for aegirine in hematite flotation in weakly acidic medium, which can strongly reduce the flotation recovery of aegirine in the pH range of 4~5 while has no evident effect on the flotation of hematite. The results of flotation tests with actual ores show the separation of hematite from aegirine gangue by forth flotation was possible, and good selectivity was achieved. Chemisorptions were observed on aegirine mineral surface treated by AHFS solution by using SEM and IR spectrum measurements. On the basis of coordination chemistry, a comprehensive mechanism, which reasonably explains the selective depression of AHFS for iron-containing silicate, is also proposed.

Jan 1, 2014

By Adam Jordens, Olga Kuzmina, Christopher Marion, Kristian Waters

"In order to meet the growing demand for non-Chinese rare earth suppliers many new rare earth (RE) mineral deposits are currently under development, however these deposits typically include many minerals for which there is little processing information available. One of these deposits is the Nechalacho deposit located in the North West Territories of Canada. This deposit contains multiple RE minerals including bastnäsite, zircon, fergusonite, allanite and monazite. The work presented here investigates the use of different classes of flotation collectors (carboxylic acids, hydroxamic acids, phosphoric acids) typically used in RE mineral flotation to float the Nechalacho ore directly. Flotation tests are also conducted as the final step in a beneficiation process incorporating centrifugal gravity concentration and magnetic separation. This combination of centrifugal gravity concentration and magnetic separation rejects low specific gravity gangue minerals such as K-feldspar and plagioclase and concentrates high specific gravity minerals such as magnetite and hematite. The removal of low specific gravity gangue helps to improve flotation and the removal of ferromagnetic iron oxides is important prior to flotation using certain chelating collectors."

Jan 1, 2014

"The JKMRC researchers have been redeveloping the suite of breakage testing techniques to more realistically align with the breakage environment in comminution equipment. Computational modelling, especially with the DEM, has highlighted the modes of impact and contact, along with the energies of these interactions in a wide range of equipment. This has driven the need to match these modes in laboratory ore characterisation tests. The objective has been to build a continuum of breakage tests and associated models that span the required range of breakage forces and environments. The ore sample is subjected to a sequence of tests covering: abrasion (surface breakage) of angular through to smoothed particles; single particle impact from high energy single impact breakage down to low energy; incremental breakage covering 60 mm down to 50 µm particles; particle strength distribution; and bed breakage over a range of compression and energy input. These tests are suited to multi-component ores with a distribution of strengths. A modelling technique is also being developed to utilise primary breakage for modelling breakage under different types of confinement. This paper draws together these techniques, previously published by the authors, into a coherent whole. The suite of tests is approaching the point where a fixed set of tests can be used to model the performance of a full range of equipment, removing the need to conduct repeat ore characterisation tests for each different piece of equipment incorporated in a circuit design. This path should open up the application of different circuit configurations and novel equipment in comminution circuit design.1 INTRODUCTION Comminution modelling utilizes a wide range of ore characterisation techniques and methods to deal with the range of comminution equipment available for production use. In general, the tests have been designed to correlate with specific pieces of equipment, using calibration factors to provide the link between the small-scale test and industrial-scale performance. The majority of tests focus on estimating the power requirement of process equipment to achieve a desired throughput and grind size. Overall, this approach has achieved acceptable outcomes in the past, but the reality is that equipment sizing suffers from considerable uncertainty, in excess of ±20% is not uncommon. This uncertainty is covered by safety margins and automatic scaling factors in equipment selection. In striving to improve reliability, the industry tends to add more adjustment factors to the tests, and design margin rather than question the basic validity of the testing process. As the tests are often correlated to production equipment via carefully guarded databases, they are also locked into historic operating inefficiency, not providing direction or revealing opportunities to improve production efficiency in comminution equipment or circuits. Safe in the knowledge that they are achieving the expected production based on test work predictions, a site is unlikely to set their sights on reducing specific energy consumption by 10%."

Jan 1, 2018

By A. Güney, G. Önal

"Karagedik Chromite Concentrator of the ETI Holding Co., which is located in Fethiye (south Turkey), has been producing chromite concentrate assaying 47-48 % Cr2O3 from the chromite ores containing 30-35 % Cr2O3 by using gravity separation methods since 1920. The tailings having 13-14 % Cr2O3, which had been removed from this plant, were accumulated at the stockpiles amounting about 1.2 million tons. In order to recover the ultra fine chromite particles from the Karagedik Concentrator tailings, the new process including Wet High Intensity Magnetic Separation and column flotation, was developed and the Karagedik Research Pilot Plant based on this process was commissioned in 2000. At this plant, the final concentrates assaying 46-48% Cr2O3 were produced and overall plant recoveries are about 60-65%.At the chromite concentrators using gravity separation methods, if their material size is about minus 1.0 mm, chromite particles especially pass to fine fractions according to their mineralogical structures and the ore-genesis (Önal and Güney, 1990). Generally, after crushing and grinding, the shaking tables and spirals are used at the chromite concentrators; therefore fine size chromite particles (-0.038 mm) are removed as tailings. Cr2O3 content of the -0.1 mm size fraction with 52.3% of the total amount is 19.58 % with Cr2O3 distribution of 82.6%.In order to upgrade the minus 0.1 mm size fraction of the tailings, assaying about 20% Cr2O3, Karagedik Research Pilot Plant (KRPP), which includes Wet High Intensity Magnetic Separator (WHIMS) and Column Flotation units, was installed by Istanbul Technical University (ITU), Mineral Processing Section in 2000.Feeding material of the KRPP having 5 tons per hour capacity is obtained from stockpiles amounting 1.2 million tons. After attrition scrubbing, the feed is sent to a screen with aperture of 1.0 mm. The screen overflow, assaying 5-6 % Cr2O3 is removed as tailings. Screen underflow is classified to –1.0+0.1 mm and minus 0.1 mm size fractions by using cyclone and sieve bend. –1.0+0.1 mm size fraction assaying 6-7 % Cr2O3, is sent to existing gravity separation plant. Minus 0.1 mm size fraction is firstly fed to WHIMS for pre-concentration and non-magnetic product assaying 10-11 % Cr2O3 consisting of serpentine, talc and olivine minerals are separated as tailings. Also magnetic product (25-30 % Cr2O3) obtained from WHIMS is fed to the two stages conditioners after dewatered to 30 % solid ratio."

Jan 1, 2003

By M. I. Panayotova

Some of effluents released by copper smelting plants are highly acidic (pH = 0~1) and contain arsenic and copper in relatively high concentrations (10~20 g/L). Usually arsenic is removed by precipitation with different reagents, such as lime, iron salts, calcium salts, aluminium salts, etc. Precipitates (often voluminous) that require further handling are formed and copper and other valuable components are lost. A method is presented for copper and arsenic extraction from acidic effluents. Effluents are treated in specially designed closed electrochemical cell without chemicals? addition. Gases formed are collected and treated for decomposing the eventual traces of As-bearing compounds and ensuring the environment protection. Initially copper of grade of 85 % is electro-won. Further about half of the initially available arsenic is separated as low-soluble, low volume mixture of intermetallic compounds, oxides and some elemental arsenic. At the next stage the main part of the left arsenic is immobilized as low soluble stable compound. Arsenic content in the treated acid is in the range 0.20~0.25 g/L. Acidity of treated effluent after first two stages remains practically unchanged and the solution can be re-used. Physicochemical and electrochemical processes, governing copper and arsenic removal, are discussed.

Jan 1, 2014

By I Brum

Brazil and Colombia have large reserves of coal, those reserves in Brazil are located predominantly in the south and Colombia the main reserves are located in the north. Despite the relative ease of exploitation, these resources have been underestimated as a source of energy. Currently, these countries are developing projects and partnerships aiming to qualify this mineral resource, adding quality to the final product of the processing plants. In this scenario the processing of Brazilian and Colombian coal in flotation columns appears as a promising alternative, having been successful in mineral systems containing fine particles This paper aims to study the overall process of column flotation for a specific Brazilian coal and a specific Colombian coal. The material used in this study consists of fine coal from Brazil (Copelmi) and Colombia (Cerrejon). The objective is to recover carbonaceous matter and reduce the ash and contaminants grade. The two coals were floated using a negative bias in a 5 cm diameter conventional flotation column of 5 m high. Flotation parameter investigated included air velocity in the range 0.6 to 1.5 cm/s. For all runs, a constant negative bias of -0.25 cm/s and a pulp concentration of 8% w/w were used. For Cerrejón coal, 300 g/ton of frother and 907 g/ton of collector was used, whereas for Copelmi coal, 600 g/ton of frother and 1815 g/ton of collector was employed. The frother was a commercial Aerofroth 65 (AF65), whereas the collector was Kerosene. For the Colombian coal, in general, yield, organic recovery, ash recovery and water recovery decreased with the increasing air rate. However, for Brazilian coal the air rate had no significant effect. For Colombian coal, the highest yield (60% w/w) and organic recovery (69% w/w) were obtained at the lowest air rate (0,6 cm/s). Keywords: negative bias, column flotation, coal

Sep 1, 2012

By Qiuyang Hong, Bo Li, Dongyun Liang

"A weathering-crust niobium-rare earth-bearing deposit is formed by the weathering alterationof alkaline granite, which is refractory due to its low grade and complex properties. The mineralogicalcomposition of ore, the grain size of majorminerals as well as the occurrence of Nb and REE are studied in this paper using MLA combined with traditional methods. According to the results, a wide range of Nb-Ti-REE compound minerals including titanoniobite, uranpyrochlore, chlopinite, samarskite and ilmenorutile areformed for the extensive isomorphous substitution among the elements of Nb, Ta, REE, Fe, Ti, U and Th. The occurrence of REE is extremely complex. First, the REEexistingas rare earth minerals including monazite, xenotime, bastnaesite,etcaccount for 21%. Second, the REEexist in the lattice of Nb and Zr minerals as isomorphous additions, which account for 18%. Third, the REE exist as colloidal rare earthdeposit,which account for 35%. Last, the REEexistingas ion-adsorption-type rare earth,which are adsorbedon the kaolinite in the form of hydrated hydroxyl ions, account for 26%.Based on the results of mineralogy, the combined technology process "mineral processing- hydrometallurgical separation" is needed to deal with the ore. The mineral processing tests show that, for the feed ore containing Nb2O5 0.065%, REO 0.13%, an Nb-REE concentrate containing Nb2O5 1.38%, REO 1.98% can be gained by "high intensity magnetic separation-regrinding-gravity separation by shaking tables". The recovery of Nb2O5 and REO is 62.42% and 44.78% respectively. The Nb-REE concentrate is dealt by the metallurgy process "direct reduction- acid leaching & acidulating- neutralization & precipitation- chlorination & distillation" and the rare earth oxide of 92.34% REO as well as the Nb-Zr oxide of 24.62% Nb2O5 can be obtained with the recovery of REO and Nb2O5 being 76.83% and 59.37% respectively."

Jan 1, 2014

By V. V. Morozov, I. S. Barmin, A. V. Tugolukov, V. V. Polivanskaya

"It was presents the results of research on improving reagent regime and scheme of enrichment of slime classes of Apatite-Staffelite ores and tailings stockpile of Kovdorsky enrichment plant. It was investigated the regularities of flocculation in the processes of thickening and selective flotation apatite-bearing ores. It was established character of the influence of flotation reagents on the flocculation process. It was shown that the sodium silicate and soda ash have a stabilizing effect by thickening of sludges. Neonol and oleic acid have a coagulating or flocculating effect. It was tested the new regime flotation, involving an initial conditioning with using of reagent - dispersants before feeding the pulp into the flotation and subsequent conditioning with reagents having a coagulating effect. The flowsheet and reagent regime for enrichment of fine-grained tailings stockpiled was developed, which providing production of standard apatite concentrate and increasing the recovery of valuable components. There are presented results of the research of activities of strong organic surfactant on solubility of colloidal form fatty acid collector and aggregate stability of fine minerals in the process of thickening and flotation. Surfactants such as Neonol have been investigated for increasing the activity of the collectors. When using the process of thickening sludge fraction with flocculant Praestol 2540 and stadial conditioning of sludge were obtained concentrates containing up to 38.1% P2O5 at recovery. INTRODUCTION A feature of the Apatite-Staffelite ores of the Kovdorsky deposit is the presence of a large number of fine mineral particles and a reduced hardness of phosphate minerals (Beloborodov et al., 2010, Tugolukov et al., 2012). Formed in the ore-preparation process, sludges are lost with a discharge in the thickening operation. Sludge is characterized by an increased content of phosphorus pentoxide (P2O5). Losses of P2O5 at enrichment of the stale tailings of Kovdorsky GOK reach 14.0%. The high losses of P2O5 caused a profound study of the behavior of thin apatite classes under conditions of thickening and flotation."

Jan 1, 2018

By R. K. Logric

Bor flotation tailings are very interesting from two reasons: first, is having due value presently, and second represent serious pollutant into this region of Balkan. This paper is only one small part of investigation about processing of valuable minerals from tailings, and desulphurization of this biggest pollutant in the same time, by refloating. The main objective of this work is to pay attention on this problem for resolve greatest environ-mental problem of Serbia and Balkan in the nearly future. Bor is potential regional risk spot, since that failure of its tailings dams would release high amounts of toxic materials that would reach the Danube River. The basic goal of this experimental investigation was finding some possibility for flotation tailings treatment by classical froth flotation. In order was obtained material effect through copper recovery, and environmental protection by moving the rest of reprocessing into the safe place. The work present obtained results of laboratory tests in two laboratories: laboratory of mineral and recycling technology at the faculty in Bor, and laboratory of department of mineral processing of ITNMS in Belgrade.

Jan 1, 2014