Search Documents

By Bo Feng

The development of surface charge of serpentine mineral and implications for sulphide ?otation have been studied through flotation tests, sedimentation tests, zeta potential measurements and optical microscope photos. The results show that the serpentine mineral was positively charged at an extensive pH range, with an isoelectric point (IEP) of 11.9. The magnitude and sign of the pyrite particles were pH dependent and were negative for pH values above 2. At pH value 9, where ?otation of nickel sul?de ores is routinely performed, serpentine and pyrite particles attract through an electrostatic mechanism. Slime coatings of serpentine adhere to the surface of pyrite, reducing pyrite flotation recovery. The removal of magnesium ions from the serpentine surface by acid leaching results in a decrease of serpentine IEP and eliminates the adverse effect of serpentine on pyrite flotation. Therefore, it has been clearly established that the surface charge value developed in the serpentine/aqueous electrical interface is a function of the serpentine surface incongruently dissolution. As a result of hydroxyl dissolution, the magnesium ions are left in serpentine surface, which is responsible for serpentine surface charge. The methods, which can remove magnesium ions from serpentine surface, can be used to eliminate the adverse effect of serpentine on pyrite flotation.

Sep 1, 2012

By P. Raghavan1

Reverse froth flotation experiments were carried out in the laboratory using two different types of kaolins for the separation and removal of coloring titanoferrous impurities from cryo-filtered clay after subjecting to high shear pre-treatment. This high shear pre-treatment consists of high shear agitation of a high solids clay slurry with the dispersant (high shear dispersion, HSD) followed by high shear agitation with the collector (high shear conditioning, HSC). After this pretreatment, the slurry is diluted and reverse flotation is carried out. One sample is from, Gujarat, India (Mamuara clay, ?MC?) while the 2nd sample is from Amberg, Germany (AKW clay, ?AC?). While MC consisted of 89% particles below 2µm and analyzed 1.06% of TiO2 and 0.29% Fe2O3 and measured a brightness of 83.4 %ISO, the corresponding values for AC are 67% below 2µm, 0.3% of TiO2? 0.49% Fe2O3 and 83.4 %ISO. The flotation performance is found to be greatly influenced by the conditions of high shear treatment. Important variables are HSD intensity (rpm), HSD time, HSC intensity (rpm), HSC time, HSD/HSC time ratio, ?HSD+HSC? total time etc. Higher shear intensities favor both the impurity liberation and collection. For both clays, it could be shown that impurity removal increases as total pretreatment time (?HSD +HSC? total time) increases up to a certain limit. For MC, the HSD time was only half or less than that of HSC time, while for AC, HSD time is at least twice (or more) than HSC time which is just an opposite manifestation. This is believed to be due to the striking differences between these two clays. Most importantly, the shear frequency is found more influential than the shear rate for the overall flotation performance for both clays. Interestingly, at high shear frequencies, i.e., when a stirrer with more number of teeth on the rotor is used, the ?HSD+HSC? total time is greatly reduced. Again, increased shear frequency helps to reduce flotation time and significantly improves flotation performance. At optimum conditions, product titania reduced to 0.35% for MC whereas the same reduced to 0.13% for AC. The product of flotation of MC measured 85%ISO brightness while that of AC measured84.6%ISO thus enhancing the value of the final product. It could also be established that the high shear pre-treatment shows better flotation performance than that due to collector dosage. Keywords: high shear dispersion, high shear conditioning, titanoferrous impurities, shear rate, shear frequency, brightness, clay recovery, Mamuara clay, AKW clay

Sep 1, 2012

By Luis Cáceres, Genny Leinenweber

"We have designed a planar perpendicular flow cell for electrochemical measurement of a mineral available as a fine powder. The working electrode consisting of mineral powder supported on a carbon paste surface as a 4 mm diameter disk, was concentrically positioned inside a vertical tubular reactor. The counter electrode was a 316L tube embedded in the body cell. The supportive media was a 1.2:1 mixture of candle wax and graphite powder respectively, which is a good electrical conductor. The concentrate electrode as a film attached on a carbon paste disk was prepared rubbing the surface carbon paste against dried powdered mineral. An Ag/AgCl 1 M KCl cell as a reference electrode was attached to the body cell by using a fast coupling fitting. A stable flow rate was achieved using a frequency inverter to drive the pump motor. The flow through the cell verified to be laminar due to the Reynolds number in the cell flow passage. Cyclic voltammetry from - 1200 a 600 mVSAgE were measured using a carbon paste with and without mineral attached to the surface. The main findings of this work were: a). Electrochemical measurement of mineral powder in contact with flowing samples was easily achieved using ground mineral. This is important where massive samples are not available. b). The voltammetric curve features of ground mineral coincided with reported data. c). The working electrode could be quickly replaced while maintaining very good reproducibility."

Jan 1, 2014

By Kazutoshi Haga, Ryo Kawarabuki, Atsushi Shibayama, Masato Kosugi, Masanobu Kawata, Refilwe S. Magwaneng, Kohei Mitsuhashi, Altansukh Batnasan

"The recovery of copper and iron from carbonaceous sulfide ore is of economic and environmental interest despite its processing difficulty. Hydrometallurgical methods can be used to concentrate sulfide metals of these hard-to treat ores in a simple and eco-friendly manner. In this study, high pressure acid leaching process was comprehensively studied to dissolve metals from an ore with organic carbon and carbonaceous gangue material using autoclave equipment. The sample used for the experiment was reduced to an average particle size of 75 µm after undergoing flotation to reduce carbonaceous gangue minerals. A comparative study on two leaching reagents of sulfuric acid and iron sulfate and their dosage was used to observe dissolution of copper and iron. Other parameters of temperature (90-170 0C), solid-liquid ratio (1:10, 1:5, 1:3 and 1:1) were investigated through kinetic studies to access the influence of organic carbon and carbonaceous material on recovery of copper and iron. Materials balancing analysis was used to evaluate the efficiency of metal dissolution. The effects of parameters on leaching rate and concentration was demonstrated. Results obtained from the experiment indicated low concentrations of copper and iron in pregnant leached solutions, which was attributed to acid consumption by organic carbon and carbonaceous material in feed. However, the high efficiency rates of 92.4% and 86.3 % for copper and iron respectively in sulfuric acid can be concluded that leaching of concentrates of carbonaceous ore is possible provided system control on type of acid, pH and temperature. The purpose of this research is important in understanding mechanism involved in dissolution of copper and iron in concentrates of carbonaceous ore and marks an improvement in leaching of highly contaminated ores."

Jan 1, 2018

By V. Beskrovnaya

Oxidised lead-bearing ores of one of the deposits of Russian Federation represent complex raw materials. Its main components are lead (3.2%~4.7%), silver (100~300 g/t) and zinc (0.7%~0.8%). The sample is characterized as oxidized ore. Silicium (37.4%) and iron (33.2%) are its main com-ponents and present in oxide form. Lead presents as cerussite, anglesite and plumbojarosite have a subject role. Zinc occurs as smithsonite. Certain part of zinc is associated with manganese minerals (psylomelane-pyrolusite). Close association of valuables with manganese-iron mineralization is ob-served. Silver is present in native finely dispersed form. Three options of flowsheets have been developed to recover valuables from the ore. 1. Hydrometallurgical flowsheet of lead and silver recovery on the basis of chloride leaching. 2. Flotation. 3. Flotation -flotation tailings cyanidation. Hydrometallurgical flowsheet of ore processing on the basis of chloride leaching (option I) al-lows to achieve recovery into saleable products of 68.8% Pb and 70.2% Ag. High quality lead concentrate with 71.7% lead and 700 g/t silver was obtained during flotation (option 2). Flotation tailings cyanidation (option 3) provides 24% silver additional recovery (from the ore). Technical and economical evaluation demonstrated that ore flotation (option 2) and flotation with subsequent flotation tailings cyanidation (option 3) are the most cost-efficient. Option II is the most cost-efficient variant of 1 tonne of ore processing (9.05 US dollars).

Jan 1, 2014

By Ho-Seok Jeon

The separation in gravity concentrators is based on the density difference between valuable and gangue minerals. In addition to density, many auxiliary parameters like particle size, shape, feed rate, pulp density etc. plays an important role in the separation. The performance efficiency of gravity units is largely based on the interference of such auxiliary parameters during separation. Many gravity concentrators are used for the beneficiation of cassiterite ores and performance of which are varying with different feed material, particle size and required enrichment from the unit. Selection of gravity units is generally based on laboratory testing and data collected from the previous experience. In the present investigation cassiterite ore collected from Uljin deposit, South Korea has been subjected to various gravity units like jig, spiral, and Knelson concentrator with the intension to pre-concentrate the ore. Second stage concentration was carried out using shaking tables. The article mainly summarizes performance evaluation methods employed for gravity concentrators. Selection of gravity circuit for the beneficiation of cassiterite was made on the basis of the recovery-grade curve, and Tromp curve methods. Keywords: cassiterite, gravity concentration, recovery-grade curve, sink-float test, tromp curve

Sep 1, 2012

By M. J. Lottering

Gold deposits in South Africa are invariably associated with uranium bearing minerals. Although it is low grade uranium by international standards, averaging around 0.3 kg U3O8 per ton of ore, recovery of uranium as a by-product improves the overall economics of gold extraction. Moreover, the current high uranium prices as well as increased demand due to renewed interest in nuclear power provide significant incentives for dedicated uranium production. An understanding of the uranium leaching response to changes in operating conditions is an important first step to-wards optimisation of uranium recoveries. In South African acid leaching plants, uranium dissolutions higher than 90% are difficult to achieve, and the chemical origin of this limit is not clear. To study leaching behaviour, an important consideration is the mineralogical characteristics of the ores. Typically, a diagnostic leaching approach can be followed. In this paper, a mineralogy-leachability explanation is presented to rationalise the difficulty in exceeding 90% dissolution from low grade uranium ores on the basis of a simple diagnostic leaching method. It was found that brannerite was the main reason for the existence of a dissolution limit in Witwatersrand ore and that chemical liberation was more effective to increase end dissolution compared to physical liberation. The findings from these investigations will form guidelines for developing economically viable flow sheets for improved uranium recovery, at least in a South African (Witwatersrand) context.

Jan 1, 2014

By G. K. Nimal Subasinghe

The establishment of grind size that optimally liberates the valuable mineral for efficient down-stream processing is of great importance for most mineral processing operations. Reasonably accurate comminution models as well as models of downstream separation processes may be found in the literature but their use in optimizing grind size is limited without an associated liberation model. In this work, an attempt has been made to address the above shortcoming by demonstrating how the effective parameters of the downstream flotation process may be predicted from the liberation characteristics based on the ore texture data for a disseminated nickel ore. In this regard, the liberation model based on linear intercept distributions of mineral and gangue proposed by King (1979) and its application to predict the flotation performance of an industrial plant demonstrated by Schaap (1979) may be considered useful contributions. However, while the model proposed by Schaap is simplistic enough, it is based on several assumptions due to the non-availability of intercept length measurements on the parent rock, in particular, on the extent of mineral exposure on the surface of comminuted particles. In this work, the linear mineral and gangue intercepts on polished specimens of a binary ore, comprising darker pentlandite as the valuable mineral and lighter barren host rock were measured using an image analyser. The resulting intercept distributions followed negative exponential distributions. Using the mean sizes of mineral and gangue intercepts, the proportion of liberated, compo-site and mineral occluded particles of a given size, the extent of mineral exposure on the surface of particles and their mean mineral contents were calculated using principles of renewal theory. The rock was then crushed and ground and different size fractions were floated. It has been shown that the parameters of observed recovery data based on 1st order kinetics such as the associated rate constant and ultimate recovery agrees well with those predicted from the quantities calculated above. This work has important practical implications since it can indicate variations in flotation performance arising from changes in mineralization within a large ore body.

Jan 1, 2014

Large quantities of electrical and electronic equipments are discarded at the end-of-life (EOL) in different industries and house hold applications. Their disposal is creating a challenging environmental problem due to the presence of hazardous metals and non-metallic materials such as epoxy resins and plastics including brominated flame retardants etc particularly in printed circuit boards (PCBs). The recovery valuable metals and separation of hazardous materials from discarded PCBs will not only conserve the resources but also mitigate the environmental pollution. From a recycling point of view for a sustainable society, the studies have been carried out for the recovery of metal values from EOL-PCBs of DVD video players (DVD-PCBs) and vacuum cleaners (VC-PCBs) using physical beneficiation techniques. The concentration of the metals was found to be 43 wt.% and 30 wt.% in DVD-PCBs and VC-PCBs, respectively. Both the PCBs samples were ground in a hammer mill after cutting and their size analysis was carried out. The liberation of the metallic and non-metallic fractions was investigated under the microscope for different size fractions. Subsequently, froth flotation and pneumatic air separation studied were carried out to enrich the metallic constituents. The studies showed the enrichment of metals in coarser particles (-1000 +150 µm) and non-metals in the finer particles -150 µm following mechanical recycling process. A grade of 90 % with 75% recovery was achieved by froth flotation, but lower grade and recovery of 75% and 65% respectively were obtained by pneumatic separation with -1500 µm powders for DVD-PCBs. A grade of 86% metal was obtained by froth flotation with 76% recovery in the case of VC-PCBs. The lower grade of 65% with almost same recovery was achieved during pneumatic separation studies due to lower concentration of metals in VC-PCBs. The studies also showed that the froth flotation is an efficient process for enrichment of metals from both the samples. The process is environmental friendly as no chemicals are employed during entire processing. The higher recovery and grade of metal is expected to be obtained on a large scale beneficiation process.

Sep 1, 2012

The ore studied occurred in the Three Rivers area in China and was a silver-lead-zinc complex ore containing 400.52 g/t silver, 4.77 % lead and 3.47 % zinc. Silver, lead and zinc were the major valuable elements in the ore and copper, cadmium and tin were the associated elements to be comprehensively recovered, whereas arsenic was the harmful element. The element silver occurred mainly in freibergite with small proportion in dyscrasite and other silver minerals. The carrier minerals for silver were mainly galena and oxidized lead minerals and then sphalerite, arsenopyrite and pyrite. The ore contained numerous minerals with complex mosaic texture and the lead and zinc minerals enclosed each other multiply, which made the separation of the minerals in the ore very difficult. Experimental investigation on the beneficiation of the ore indicated that with flotation separation process it was very hard to obtain single lead concentrate or single zinc concentrate that would meet the requirement of market. In the meantime, during the separation process of lead and zinc, silver tended to be dispersed, resulting in a low recovery of silver. Therefore, a rational utilization technique for the ore should be a combined process of bulk flotation to reduce arsenic? sulphating roasting of silver-lead-zinc bulk concentrate-leaching with diluted sulphuric acid to separate silver, lead and zinc. With this process quality lead concentrate containing silver and high grade zinc product and silver product could be obtained. The recovery of silver, lead and zinc in flotation was 85.10%, 84.48% and 82.48%, respectively. The total recovery of silver, lead and zinc in chemical processing was 97.07%(sum of recovery of silver ingot and lead concentrate), 99.61% and 90.93%, respectively.

Jan 1, 2014

By V. A. Vorob'ev, A. N. Larionov, E. N. Ivanov, M. A. Ryazanov

The aim of the research is to increase the recoverable value of poor, difficult-to-digest complex mineral raw materials. In the Republic Belarus, universal centrifugal-shock devices have been created for crushing, grinding and classification of ore and non-metallic mineral raw materials in dry mode, which differ from foreign analogues by a higher level of resource saving (including electricity and materials). Dry-ore preparation technologies have been tested on a pilot scale: fine crushing (replacing grinding in rod mills), grinding (replacing wet grinding in ball mills) and pneumoclassification on different types of ores, - which made it possible to identify the criteria for the suitability and unsuitability of mineral raw materials for their use. The possibility of regulating the upper and lower limit of the size of the finished material is established, the possibility of reducing the yield of slimes (-0,020 mm) to 5 times is determined. A comparative analysis of the contrast degree of separation characteristics of ore a similar granulometric composition, crushed in wet and dry conditions, is performed. The achieved contrast degree of gravity properties after dry grinding - 104,3; after the wet - 60.2. When enriching on a centrifugal concentrator, gold recovery to the concentrate after dry grinding increased by 13.12% while improving the quality of the concentrate from 78.3 g/t gold to 90.75 g/t. When testing the gravity-flotation scheme for the enrichment of poor gold-quartz ore, the increment of gold extraction after dry grinding was 7.6% for gravity and 9.5% for flotation; the total increase in extraction is 17.1%. The possibility of flotation of a larger material after dry grinding has been proved, with an extraction gain of 1.5% compared to the flotation of thinner material after ball milling. The influence of dry technology on the efficiency of the leaching of gold and silver (an extraction gain of 5.5 to 10%) and heap leaching (extraction gain - up to 18.3%) was studied. The positive influence of dry ore preparation technologies on the efficiency of gold and silver heap leaching and heap leaching, thickening and filtration is proved. Lines of dry ore preparation technologies can be used in modular complexes for processing technogenic raw materials.

Jan 1, 2018

By B. McFadzean, P. E. Ngoepe, P. P. Mkhonto

"The theoretical technique of computational modeling and the experimental determination of the enthalpy of adsorption of a ligand molecule onto a mineral surface deliver the same output parameters and, therefore, complement each other in investigating the affinity of different ligand types for mineral surfaces.This study ran parallel experimental tests and computational calculations to determine the enthalpy of adsorption of a series of increasing chain length xanthates onto a pyrite surface. The outcomes showed that, while the absolute energy values were different, the trends were similar. Both computational and experimental approaches showed that the extent of the interaction of the xanthate molecule increases with increasing carbon chain length. The computational values were larger than the experimental values, which could be explained, in part, by the addition of water to the computational system, which resulted in a decrease in the heat of adsorption on the (100) surface, compared to the adsorption of the collector in a vacuum. The computational method showed that, in the case of the pyrite (100) surface, the most exothermic reaction was obtained when the two xanthate sulfur atoms bridged two pyrite 5-coordinated iron atoms. The (111) surface was found to be more reactive and different adsorption mechanisms were predicted for each of the C2, C3, C4 and C5 chain length xanthates.The experimentally determined exothermic increase in heat of adsorption for the addition of each CH2 group was found to be -8.17 kJ/mol. The contribution of the thiol head group was -34.9 kJ/mol. Previous studies on self-assembled monolayers have shown that these values are compatible with lateral interactions between CH2 groups and the exclusion of water. This study provides a rigorous experimental and computational approach which is intended to afford confidence in modelled data for the screening of new ligands for flotation processes.INTRODUCTIONComputational modelling is a fast and cost-effective method of screening collector molecules for the efficacy of their adsorption onto mineral surfaces. However, it is desirable to measure the computational outputs against experimental outputs to check for congruency. Computational modelling and experimental microcalorimetry both deliver the same output parameter: the energy of adsorption of the molecule onto the solid surface. These techniques are therefore ideally suited to complement one another in investigating the affinity of the interaction between collector molecules and mineral surfaces."

Jan 1, 2018

By A. Oberrauner

Electrostatic separation is a dry separation technique usable for many applications in the mining- and recycling industries. At the Chair of Mineral Processing intensified research has been done on this topic during the last years. One challenge was to measure the triboelectric charging of fine mineral particles in a triboelectric charging device consisting of an electrically insulated polyethylene rotor/stator assembly. These tests, performed on monomineralic samples, were accomplished in a climate chamber. It was shown that charging of minerals not only depends on rotor speed, feed rate and atmospheric circumstances but also on the properties of the applied electrostatic field. Tests on pure calcite in contact with the polyethylene rotor/stator system resulted in specific triboelectric charges up to +10 nC/g at low relative humidity. With more water present in the surrounding atmosphere, these charging values decreased significantly. However, at higher relative humidity, triboelectric charge values could be maintained after an electrostatic field of positive polarity was applied. Similarly, charging behavior was found with other hydrophilic minerals. The idea behind all these tests was to find the largest charging difference between minerals occurring together in a deposit and to be able to charge them oppositely, assuming that this means good sort ability in an electrostatic separator. The results gained from these investigations are shown. After having obtained many results on charging pure minerals, it became interesting to test the applicability of the charging tendencies on electrostatic separation of fines <100 µm. In order to do so, a separator for fine polymineralic powders was developed, constructed and combined with the triboelectric charging device, all being set up in a climate chamber. This new so-called coax-separator is presented along with first test-results.

Sep 1, 2012

By Peter N. Holtham, Geoffrey J. Lyman, Matthew S. Brennan, Vijay Subramanian, Rui X. Rong, Tim Napier-Munn

Studies of the dense medium and classifying cyclone have been conducted using the Fluent computational fluid dynamics code. Experimental measurements of the segregation of medium in a DM cyclone by gamma-ray tomography and the performance of a novel classifying cyclone design have been used to test and interpret the 3D CFD predictions. The predictions of the CFD models were generally plausible, though more work is required to incorporate turbulent mixing of the slurry in the cyclone. The benefits of the novel cyclone design were explained by the model in terms of conditions favouring reduction of short-circuiting at the vortex finder, and the removal of the air core from the wall at the apex. Work is continuing.

Jan 1, 2003

By P. Gao, J. W. Yu

"Pre-concentration is a necessary step for upgrading low-grade iron ores, and its aim is to remove gangue minerals for improving efficiency of downstream separation process. The most important pre-concentration technique for iron ores, including hematite, siderite and limonite, is magnetic separation based on the appreciable differences between the desired iron minerals and gangue minerals in magnetic susceptibility. In this paper, the separation efficiency of one-stage low-intensity magnetic roughing combined with two-stage high-gradient magnetic scavenging for the pre-concentration of a low-grade hematite from Donganshan was investigated. It is a BIF type of ore containing hematite, magnetite and a bit of siderite, and an average content of Fe is about 34.6%. The effects of grinding fineness and magnetic field intensity for scavenging I and II were studied and optimized. The results showed that a magnetic preconcentrate assaying 42.7% with a recovery of 95.4% was obtained under the conditions of ore grinding fineness of -74 µm 70%, magnetic field intensity of 300 mT and 800 mT for scavenging I and II, respectively. Over 20% of the feed was rejected as the final tailings assaying 6.4% Fe. Meanwhile, the XRD, iron chemical phase and SEM analyses of different stage products revealed that hematite, magnetite and siderite could be recovered successfully by magnetic separation. However, some ultra-fine hematite particles (-10 µm) were difficult to be captured by magnet, and lost in the final tailing, resulting in lower iron recovery.INTRODUCTION Donganshan iron ore belongs to sedimentary-metamorphic iron formation called banded iron formation (BIF), which is formed in the Precambrian with a layered structure composed of ore bodies (Shen, 2012). Such type of iron deposit contains various iron-bearing minerals like hematite, magnetite, and siderite, suggesting it may be amenable to pre-concentration with magnetic separation. The pre-concentration process is effectively applied in recovering hematite, magnetite and siderite from iron ore, due to its benefits of further upgrading iron ore and improving separation efficiency. The most important pre-concentration technique for iron ore is magnetic separation, including low-intensity magnetic separation and high-gradient magnetic separation, based on the fact that there are appreciable differences between the desired hematite, magnetite or siderite and the gangue minerals in magnetic susceptibility."

Jan 1, 2018

By A. Vidyadhar

Using pure quartz and hematite minerals, the adsorption mechanism of mixed cationic/anionic reagent schemes was investigated through Hallimond flotation studies. The flotation response of quartz and hematite independently with cationic and anionic collectors as well as with mixed cationic/anionic collector systems is assessed. The flotation response as a function of pH and collector concentration was investigated. The single mineral flotation tests in the presence of anionic collectors, quartz does not respond to flotation, but the C12 amine flotation of quartz was observed to be pH and concentration dependent. It was observed that hematite flotation recovery is maximum at acidic pH with sodium dodecyl sulphate (SDS), neutral pH with oleate, and at basic pH about 9.5 with C12 amine. Flotation results with both quartz and hematite indicate an increased adsorption of cationic collector in the presence of anionic collector apart from its own co-adsorption. The incorporation of oleate in between C12 amine molecules decreases the electrostatic head-head repulsion and thereby increasing the adsorption of C12 amine due to attractive tail-tail hydrophobic bonds, besides forming a closely packed adsorbed layer enhancing the hydrophobicity. The increase in oleate concentration beyond C12 amine concentration leads to the formation of soluble C12 amine-oleate complex / precipitate and the adsorption of these species decreased the flotation since the alkyl chains are in chaotical orientation with a conceivable number of head groups directing towards the solution phase. Keywords: quartz, hematite, adsorption, mixed collector system, flotation, zeta-potential

Sep 1, 2012

By N. ??dyanik, Z. Kugukaldinova, O. Mishurina, Y. Glazkova, E. Mullina

"This paper describes the process flow of a selective processing method for acidic mine waters formed in the copper sulfide industry and characterized by a high content of copper, iron, and manganese ions. The proposed method comprises a series of sequential processes: the 1st stage is the recovery of Cu2+ ions by precipitation, the 2nd stage is the recovery of Fe2+ and Fe3+ ions as a dispersed phase by acid-base precipitation, followed by recovery in the 3rd stage of Mn2+ ions by converting Mn2+ with an oxidizing agent into insoluble forms of manganese and subsequent recovery of the dispersed phase by electroflotation. The developed method was tested on the acidic tailing storage facility (TSF) water of a mining project in the Urals region. The practical results of the implementation of the developed method have shown that its implementation will allow to recover copper, iron, and manganese in the form of salable products with a simultaneous decrease in their concentrations in adjacent water bodies down to the applicable MPCs. The process is a simple one, does not require any sophisticated expensive equipment and can be implemented either as a standalone solution or as part of existing treatment facilities. INTRODUCTION As a result of unsustainable utilization of natural resources in Russia, only a small fraction is processed into commodity products, while the rest is systematically dumped as emissions, effluents, and other wastes, polluting the environment. By amount of waste and concentration of valuable components, those wastes can be classified as aqueous technogenic resources [1, 2]. Therefore, the development of processing methods for this mineral resource category is an urgent and priority task that will significantly improve the industry’s profitability and the environmental conditions in the respective regions. MATERIALS AND METHODS Following research methods were mainly applied in this study: lab-scale and pilot-scale tests in a diaphragmless two-chamber electric flotation cell; for solutions and recoverable process products — chemical analysis using photometric determination techniques for metal cations and atomic adsorption determination techniques for the processing products. The phase composition of the precipitates formed in the process was investigated by X-ray phase analysis in the general-purpose diffractometer with a copper anode DRON-1."

Jan 1, 2018

By H. Mengbing, A. Potokin, A. Usov

"Revealed and analyzed in the study are the ways of significant perfection of specific characteristics of the equipment, such as use of high-frequency voltage transformation to create a charger; use of pulse transformers, with core made of materials with high magnetic permeability, in pulse generating circuits; as well as use of special ways to produce voltage pulses with a short front. The experiments have proved the possibility to adapt these technological solutions for electric-pulse installations, and suggested on this base is a strategy of further development and application of electric-pulse technologies. The different applications joint work schemes of voltage sources with two levels voltage and energy in electric pulse technologies are investigated. The possibility of increasing energy efficiency of destruction is shown."

Jan 1, 2014

By Tracy Shimmield, Philip Samar

"Metals have been mined as ores since pre-history but metal production has increased dramatically in modern times driven by expanding Global GDP. Metal ore mining produces large amounts of waste rock and mine tailings. Mine tailings are the wastes produced after extracting the desired metal from the ore. There are several ways of dealing with this waste, and Ritcey (2005) identifies the following possibilities, land-based storage, backfill to the mine, deep lake disposal and marine disposal. In Papua New Guinea (PNG), both Misima and Lihir Mines adopted the marine disposal option, releasing tailings through a submerged pipe onto the sea floor. This special case is referred to as Deep Sea Tailings Placement (DSTP) in which the tailings deposition is sufficiently deep as to be below the euphotic zone. The most important aspect of deep sea tailings placement is that the tailings are deposited at great depth where exchanges between the seabed and the surface layers are small. The first quantitative multidisciplinary study of tailings impact on the deep sea was carried out from 2006 to 2010 in Papua New Guinea. The physical, chemical and biological work carried out has placed PNG at the forefront of research into the assessment and management of deep-sea environmental impacts related to mining in PNG. The study has provided data which has led to a better understanding of the ecological and geochemical processes in deep water that accompany DSTP in PNG and provided baseline data on deep-sea ecosystems in a scientifically poorly known tropical ocean. Additionally, guidelines on best practice for DSTP have been developed Here we present geochemical data obtained from sediment samples from the marine environment surrounding Lihir and Misima Islands."

Jan 1, 2014

By Gülay Bulut, Ünzile Yenial

"Water composition has a significant effect on flotation. A better understand the role of water composition in flotation is very important for process quality and performance. Based on source of process water, the concentrations of the dissolved ions, hardness, contaminants and residual composition of reagents can varied in the process water. The various water resources employed during lead and zinc flotation caused activation, depression or selectivity effects on minerals due to the presence of different ions in solution. Metal ions in these water resources were adsorbed on the ore, whilst ions associated with gangue minerals were released into the flotation pulp.This paper includes a research for the effect of different water compositions on lead and zinc sulphide flotation. Experiments were carried out five types of water such as tap water, recycling water, tailing dam water, underground mine water and sea water. The ore sample was obtained from Esan Balikesir-Balya mine. The mineralogical study of ore sample shows that it contains mainly galena, sphalerite, pyrite, hematite, quartz, diopside, epidote, calcite, and chlorite. It is found that recycling water and tailing dam water has a positive effect on recovery of lead and zinc minerals and detrimental effect on content of both minerals. This result may explain with remaining reagents in these waters. Underground mine water and tap water gave nearly the same recoveries of zinc. Sea water affects the recovery lead and zinc negatively."

Jan 1, 2014