Search Documents

By Z. G. Song, C. Y. Sun, X. R. Zhang, Y. Yu

In skarn type scheelite deposit, there are calcium minerals with floatability similar to scheelite, such as calcite, fluorite, etc., which are difficult to separate. Heating cleaning method developed by Petrov has been widely applied in processing rough concentrate of scheelite for nearly half a century, but there exists a general lack of full understanding of the interaction between floatation reagent and mineral particles surfaces. The mechanism on separation of scheelite and calcium minerals in heating cleaning process was investigated by mineral flotation experiments, XPS analysis, as well as solution chemistry and crystal chemistry calculations. The results showed that the sequence of minerals floatability using sodium oleate as collector and a large amount of sodium silicate as modifier in heating flotation test was scheelite > calcite > fluorite, which was the same as solution chemistry calculations based on Gibbs free energy vs. pH and also the same as Ca-X intensity order by crystal chemistry analysis. There are two sides about the mechanism of heating cleaning method: one is that the adsorbed collector on calcium minerals surface is desorbed more easily than scheelite, and the other is selective dissolution of calcium ions from the mineral surface because of Ca-X intensity difference in heating and stirring process.

Jan 1, 2014

By Steven Wright, Sharif Jahanshahi, Shouyi Sun

"While there is a large industry based on recovering platinum group metals (PGM) from complex sulphide ores containing Cu and Ni, there is little information on the thermodynamics of the matte phase formed on smelting the ore and in particular the behaviour of Pt in the matte.The equilibrium between metallic platinum and industrial mattes was studied in a series of experiments where a small quantity of matte (5g) and platinum foil of 150 µm thickness (0.5 g) were equilibrated in magnesia crucibles at 1400°C under conditions where the oxygen and sulphur partial pressures were fixed.The chemical composition of the phases was determined from EDS analysis using a scanning electron microscope. Line scans were initially used to confirm that the foils had attained a uniform composition across their thickness. The composition of the matte was determined from analysis of an area of matte including the small metallic droplets and dendrites.The results of the equilibrium study are presented in terms of how the oxygen and the sulphur pressure affect the distribution of Pt, between the matte and the alloy foil (Lmatte/alloy). Other variables investigated were matte chemistry, i.e., the Fe content and the temperature. The activities of platinum in the mattes were calculated using a regular solution model describing the activity-composition relationship in the alloy."

Jan 1, 2003

By Ronel du Plessis, John C. Davidtz, Jan D. Miller

Xanthates (dithiocarbonates) have been the collector of choice for the flotation of sulfide minerals ever since the flotation process was developed and have been studied quite extensively. Recently, trithiocarbonates have been shown to be very effective in bulk sulfide bench-scale flotation. Fundamental analysis using electrochemical techniques have supported these bench-scale results, illustrating that the trithiocarbonate (TTC) collectors are more readily oxidized to their corresponding dithiolates, than the dithiocarbonate (DTC) collectors, as is shown in Figure 1.

Jan 1, 2003

By Ashutosh Shandilya

Froth flotation is a selective separation process and rarely used for beneficiation of limestone in the world as compared to other minerals and also mostly known conventional methods of up gradation of ROM including wobbling, selective mining, sorting, preblending etc. Limestone is mainly used in the manufacture of cement, steel and chemical industries. High grade limestone deposits are depleting day by day and the requirement of the industries have to be met by beneficiating the low grade limestone deposits in the world. And because of marginal quality of limestone, it cannot be directly used in cement industry. At ACC Madukkarai cement works, Coimbatore, Tamilnadu, full fledged mineral beneficiation process is adopted to enhance the quality of low grade lime stone from 38-42 % CaO to 45-47 % CaO and silica reduced from 19-22 % to 11-13 % by use of oleic acid (commercial grade and vegetable origin) 0.38 kg/ton of limestone and caustic soda 0.05 kg/ton of limestone. Keywords: OK-8 Cells, Froth flotation process, Beneficiation studies, Low-grade lime stone, Oleic acid, % solids, Pulp density, Ph, Iodine value, saponification value, Denver cell

Sep 1, 2012

By N. T. Beukes, W. Banda

Recovery of Co from slag is a recent advancement in the extractive metallurgy of nonferrous metals. In this study a DC arc technology at laboratory scale has been applied to investigate the selective recovery of Co from slag, under three different flux types with an emphasis on influencing the activity of FeOx, SiO2 and CoO in the slag. It is known that reduction of slag by carbon is only up to a certain level after which, the recovery will depend on the chemistry of the slag, hence the need to modify the slag chemistry. Two power settings were employed to induce higher temperatures and aggressive agitation. The results were interpreted by comparing how much Co and Fe was in the slag and alloy. TiO2 reduced the amount of Fe in the product alloy compared to when CaO and CaF2 were used. The change in power did not seem to have had a major effect on the recovery although the amount of material lost to flue dust was more at a higher power rate.

Jan 1, 2003

By Richard K. Komarek, Antonios Zavaliangos, Roman T. Dec

Roller presses are widely utilized in mineral industry for fine milling and compaction. Recently used models are providing only limited information about the material behavior in the roll bite. This paper introduces a 2-dimensional finite element model for analyzing those two basic processes. A pressure-dependent plasticity model with linear elasticity was used as a constitutive model for the particular material. Coulomb friction law was used to describe phenomena on the material/roller surface interface. Two basic roller geometries are considered: smooth (used for milling and compaction) and with cavities, commonly used for briquetting. Comparison of the results obtained from the model with experiment indicates that they are following the general trends of experimental values recorded with laboratory roller presses. It is shown, that the model is suitable to analyze material behavior through all stages of the rolling process: feeding zone, nip region, neutral plane and release section. It can predict pressure, shear stress, slip of the material over the roller surface, material velocity field, failure of the compact during release and the course of other important process variables. This allows the process engineer to gain an improved understanding, leading to a better process and equipment design and control.

Jan 1, 2003

By Xianjun Lyu, Junxiang Wang, Peng Wu, Minjie Lian

"In recent years, the efficient cementation of mine tailings is a new way to manage mine solid wastes. The traditional cement materials have a slow setting time, large dosage and poor cementation strength for fine aggregate such as mine tailings. Therefore, the preparation of new type cementitious materials for the cementation of fine tailings has great potential in the treatment of mine waste solids. The paper mainly focuses on exploring the critical factors affecting the cementing performance of granulated blast furnace slag and its performance in the cementation of fine aggregate. Results indicate that the fineness of slag has a significant effect on its cementitious activity and Portland cement clinker has a better stimulation effect on the cementitious properties of slag than lime. And, anhydrite has a better early stimulation effect on the cementitious properties of alkali-activated slag compared to semi-hydrated gypsum and dihydrate gypsum. According to a series of tests on the cementation of fine iron tailings, the optimal ratio of slag, Portland cement clinker and anhydrite is determined as 60:30:10. Compared with P.O 42.5 ordinary Portland cement, the new slag based cementitious material shows much better cementing performance on fine tailings sample. Under the dosage of 12%, the compressive strength of fine tailings mortar using slag-based cementitious material in 3 curing days is increased to 168% that of using P.O 42.5 ordinary Portland cement, while the compressive strength in 28 days curing period is increased to 194%."

Jan 1, 2018

By Jacques Eksteen, Sharif Jahanshahi, Neill J. Bartie, Shouyi Sun

The gradual increase in Cr2O3 levels of UG-2 ores has become a matter of concern for platinum producers in South Africa due to the formation of chromite spinels in melters. The effect of bulk FeOx/MgO ratio, Cr2O3, temperature and oxygen partial pressure on phase stability and composition in the system FeOx-MgO-SiO2-Cr2O3-Al2O3-CaO has been studied between 1400°C and 1600°C using the drop-quench technique. An increase in temperature was found to result in a decrease in [Fe/Cr]spinel. This effect is shown in Figure 1 for the six slag compositions investigated.

Jan 1, 2003

By J. Wiese, K. Corin, Z. Song

"Relating flotation performance to the electrochemical characteristics of a pulp is complex both in fundamental research and in practice. In the case of thiol collectors, different Eh values in the flotation system can result in the formation of the dimer or the metal thiolate which may or may not enhance the hydrophobicity of the mineral. Reducing or oxidizing conditions in a flotation system, viz. changing the Eh value, are usually manipulated to achieve an optimum flotation response by control of pH and dissolved oxygen levels in the system. A variation in pulp potential may also be achieved by the addition of potential modifiers such as sodium hydrosulphide (NaHS), sodium hypochlorite (NaClO) or hydrogen peroxide (H2O2). There exists anecdotal evidence which suggests that the addition of small amounts of H2O2 to the flotation process can improve sulphide mineral recovery. The objective of the present study was to investigate the effect of the addition of the potential modifier, H2O2, on sulphide mineral recoveries and grades in the flotation of sulphide minerals from two copper bearing ores from China and compare the results to those obtained for a PGM bearing ore South Africa. Batch flotation tests were conducted using the three different ores at the natural pH of the different systems, in the presence of a xanthate collector and the absence and presence of H2O2 as a potential modifier. The results indicate that the addition of carefully controlled low concentrations of H2O2 resulted in improvements in flotation performance. INTRODUCTIONElectrochemical potential as a control parameter in the flotation of sulphide minerals has been widely studied (Allison et al., 1972; Gardner and Woods, 1979; Ross and Van Deventer, 1985; Chander, 2003; Woods, 2003; Javadi, 2013). There is concensus that in order to be recovered during flotation, sulphide minerals require a suitable redox environment. During the flotation process thiol collectors and sulphide minerals are involved in electrochemical reactions which result in the formation of hydrophobic species at the mineral surface (Finkelstein and Goold, 1972; Rand and Woods, 1984). Sulphide minerals act as semiconductors and electrons are transferred during the interaction of the mineral with collector. The resultant potential difference and its magnitude are responsible for the transfer of electrons and the rate of the reaction (Bard and Faulkner, 2001; Fuerstenau et al., 2007). Reducing or oxidizing conditions in a flotation system, viz. changing the Eh value, may be manipulated to achieve an optimum flotation response by control of pH and dissolved oxygen levels in the system (Heyes and Trahar, 1979). The use of potential modifiers viz. reducing or oxidizing agents which include H2O2, NaClO, and NaHS, is an alternative method by which to control the potential of the pulp in a flotation system which may or may not promote the flotation of desired minerals (Rao, 2004). The oxidizing agent, H2O2, undergoes a cathodic reaction which can result in the enhanced flotation of valuable minerals. The potential of the system is increased which results in a shift in the mixed potential of a mineral. The magnitude of the over-potential influences the rate of the oxidation process and thus the flotation response of sulphide minerals (Kocabag and Guler, 2008). Equation 1 shows the proposed oxidation of xanthate by H2O2 (Lipkina and Streltysn, 1970)."

Jan 1, 2018

By S. Castro, L. Uribe

Seawater can be considered as a particular process water with a high concentration of NaCl (about 0.5- 0.6 mole/L) and high concentration of hydrolyzing metal cations (mainly, Mg2+ and Ca2+ ions). Micro-flotation tests, induction time measurements, and zeta potential measurements have been used to investigate the effect of these ions on the natural floatability of molybdenite. The results demonstrate that molybdenite is strongly depressed in the alkaline pH range over which hydrolysis products of Mg2+ and Ca2+ ions are formed. At pH 10, colloidal magnesium hydroxide seems to be responsible for molybdenite depression in seawater and in Mg2+ solutions. This is also supported by the measurements of the effect of Mg2+ ions on the zeta potential of molybdenite. The mechanism of depression of molybdenite with Ca2+ ions is different, and depression takes place in the pH range were Ca(OH)+ complexes are formed, below the pH of precipitation of calcium hydroxide. Adsorption of the cationic hydroxy species and/or hetero-coagulation of the positive charged colloidal hydroxide on the negative charged molybdenite particles seem to be the main mechanisms involved.

Jan 1, 2014

By V. I. Ryaboy, I. V. Ryaboy, E. D. Shepeta

"The problem of separation of copper minerals and arsenopyrite remains relevant because of environmental requirements. The selective action of reagents with the thioamide group (thioamides) is known in iron sulfide’s flotation of pyrite and pyrrhotite. The aim of this study was to reduce the arsenic content in the copper concentrate when using thioamides by reducing the flotation of arsenopyrite in the flotation of the sulfide part of the skarn scheelite-sulfide ores. We have chosen the most widely used thioamides for the study, such as Z-200. We also synthesized new reagents with the thioamide group. The most selective and the most powerful thioamide copper collector were used for further studies. Reduction of arsenic content in copper concentrates is achieved in the following way: You need to apply a strong thioamide collector with a selective but weak dialkyldithiophosphate collector, or vice-versa, a selective, but a weak thioamide collector should be used with the dialkyldithiophosphate reagent with strong collective properties. The proposed combination presents industrial interest because of its accessibility. The application of thioamides in copper minerals and arsenopyrite selection has showed that these reagents have fewer selective properties than dialkyldithiophosphates. To achieve the comparable recovery of copper using dialkyldithiophosphates requires markedly greater consumption of thioamides, due to their lower hydrophobic ability. The application of a composition of thioamides and dialkyldithiophosphates allows to increase the recovery of copper and to obtain a lower arsenic content in copper concentrates compared to their individual use. The lowest arsenic content in the copper concentrate is obtained in the composition consisting of the newly synthesized thioamide with strong collective properties and selective dialkyldithiophosphate. The addition of even small amounts of xanthate to the composition of thioamides and dialkyldithiophosphates causes a sharp increase in the arsenic content in the copper concentrate without a notable increase in copper recovery."

Jan 1, 2018

By S. J. Liu

The conventional collector for bauxite mineral is oleic acid, which is highly insoluble and must be used in high dosage in bauxite flotation operations, that is the great drawback of oleic acid in use. A series of hydroxamic acid were synthesized, and their collecting ability to certain minerals in bauxite: diaspore, kaolinite were studied. The collecting power of various reagents to diaspore in an incremental sequence were shown as follows: benzyl hydroxamic acid<amylic hydroxamic ac-id<heptylic hydroxamic acid<oleic acid<octylic hydroxamic acid; while the incremental sequence of the collecting power to kaolinite was like this: benzyl hydroxamic acid<amylic hydroxamic ac-id<heptylic hydroxamic acid<octylic hydroxamic acid<oleic acid. It could be seen that octylic hydroxamic acid had the capability of high collectivity and good selectivity, and octylic hydroxamic acid was chosen to use in the following experiments. Reduced zeta potential showed the adsorption of the anionic collector on the mineral. By the adsorptive capability and IR tests, the adsorption of octylic hydroxamic acid on diaspore was determined to be chemical absorption, which was greater than that of oleic acid, as it was physical absorption. Results of floatation experiments on manually mixed minerals indicated that the collectivity and selectivity of octylic hydroxamic acid were better than oleic acid.

Jan 1, 2014

By N. Ahmed

This paper is concerned with the drainage behaviour of gangue mineral in the froth phase. Experiments were carried out in a continuous laboratory flotation cell in which froth depth and bubble size could be changed independently. The fraction of solids returning from the froth to the pulp zone was expressed using a rate constant. A mixture of hydrophilic solids (silica) and floatable particles (glass ballotini) was used as a flotation feed. Samples of glass ballotini of different hydrophobicities were obtained, using controlled silanation. Three samples, with contact angles of 50, 66, 82 degrees, were used. The effect of the initial bubble size (pulp bubble size), concentration of gangue mineral in the froth zone, and froth depth on the drainage of silica, were investigated. The drainage rate of the entrained solids increases with an increase in the degree of hydrophobicity of the floatable particles. Concerning the effect of pulp bubble size on the drainage rate of entrained solids, larger bubbles always give higher drainage rates due to formation of relatively loose froth structures which allow gangue particles to easily move down to the pulp zone. Conversely, smaller bubbles exhibit lower drainage rate constants, in particular at shallow froth depths.

Jan 1, 2003

By Jan Svoboda, Toyohisa Fujita

"The current status and history of innovation in magnetic methods of material treatment are reviewed. The milestones and key drivers of innovation are identified, advantages of magnetic separation in comparison to other physical methods of material manipulation are discussed and reasons for failure to live up to its potential and expectations are identified. The future focus in such diverse areas as mineral processing, waste treatment, recycling and biosciences is discussed and the research and development needs are outlined.Our walk through the innovation landscape in magnetic separation illustrates the enormous effort that has been expended over the years to convert a wealth of novel idea into workable techniques. Remarkable progress has been achieved and numerous successful innovations have been introduced into material treatment operations. On the other hand these techniques have experienced their fair share of failures. The reasons for these cover a wide spectrum of risks that accompany any effort to implement new technology."

Jan 1, 2003

By S. M. Mustakim

Red mud is the major waste material produced during digestion of bauxite ores with caustic soda in alumina production following the Bayer?s process. Its disposal remains a worldwide issue in terms of environmental concerns. A lot of research and developmental activities are going on throughout the world to find effective utilization of red mud, which involves various product developments. At present, building materials, industries are fast growing industrial sector where the need of various raw materials is enormous. The use of red mud in building material production is one of the options for conservation of natural resources and reduction of environmental pollution. A cost-effective and energy efficient mineral cementation process has been developed at CSIR-IMMT, Bhubaneswar for use of red mud in manufacture of building brick, block and aggregate. The red mud is an alkaline material, which contains both leachable and non-leachable soda along with different mineral constituents of alumina, iron and silica. The effort has been made to use the mineral constituents of red mud to develop cold setting building brick by mineral cementation process using a binder specially prepared from Portland Slag Cement, Lime, Gypsum and Alkali metal sulfates. The red mud has been used from 40 to 70% by weight along with fly ash and binder in development of cold setting building brick conforming to the specification of IS:12894:2002.

Sep 1, 2012

By V. K. Kuppusamy, M. Holuszko

"Lamps and lighting products are the most commonly used electrical products around the globe. With the improvement in lamp technologies, lighting products have grown complex and hence require an improved recycling process. The LED lamps consist of various valuable metals such as iron, copper, aluminum, chromium, silver, and gold, as well as non-metals such as glass, plastics, and fibers. In addition, there are also traces of hazardous substances such as lead, arsenic, and mercury. A major step in the recovery process is size reduction, and researchers have suggested that up to 40% of the total valuable material is lost during the shredding and grinding processes. SELFRAG is a high voltage selective fragmentation comminution technology that uses high voltage pulses in a water medium to efficiently separate the metals at a coarser size without generating many fine particles. It has been proposed that during the fragmentation process of electronic waste (e-waste), the metals can be separated without fine grinding. This research considers the applicability of high voltage pulse fragmentation for LED lamps. Eight different types of LED lamps were processed through the SELFRAG unit at varying pulses to study metal liberation. The product obtained was characterized for metal liberation, metal grades, and liberation analysis. The specific energy consumption for this size reduction process was also monitored. INTRODUCTION Lamps and bulbs are the most commonly used electrical products in homes, offices, industrial operations, and streets. According to Energy Star research (2006), an average US household has more than 40 sockets for light bulbs and consumes approximately 2100kWh every year for lighting. The development in lamp technology has pushed the boundary for newer products. The LED lamps have been taking over the market from the incandescent bulbs and compact fluorescent lamps (CFL). According to the US Department of Energy (2012) and myLEDlight.com (2007), LED lamps have several benefits over other lamps. LEDs produce light hemi-spherically, which increases their efficiency in directional light emission. It has higher breakage resistance from vibration or transportation. LED lamps use up to 90% less power than incandescent bulbs thus making them highly energy efficient; They have a longer lifespan, lasting 10 times longer than a CFL and 133 times longer than the traditional incandescent bulb. Because of all the benefits, Smallwood (2014) suggested that the market of LED lamps will grow to $12.2 billion by 2018."

Jan 1, 2018

By F. B. Waanders

Coal, as energy resource, possesses numerous characteristics and properties which all have an influence on its gasification behaviour. The two properties considered as critically important when evaluating a coal source for gasification is its mineral content and slagging behaviour. Research has indicated that slagging formation can be inhibited or even prevented by the addition of a fluxing agent. It is thus of great importance to understand the mineral interaction during gasification in order to select a suitable fluxing agent for the prevention of slagging and clinker formation in the gasifier. The aim of the present project is to evaluate the effect of iron as a fluxing agent and study the transformation of the mineral and added iron during gasification. A pre-determined amount of pure elemental iron (between 2wt% and 20wt%) was added to a base case coal sample in order to study the effect of the addition of iron to the coal. The transformation of the iron in conjunction with the possible iron containing minerals present in the coal was studied by means of Mössbauer analyses. Typical characterisation techniques included proximate analyses, ultimate analyses and ash composition analyses. The ash fusion temperature analyses (AFT) were used to study and predict the slagging behaviour of the iron-spiked coal samples. Even though AFT analyses only provide an average flow property, it gives a good indication of the changes that the iron addition induces on coal properties. FactSage modelling was carried out in conjunction with the Mössbauer and AFT analyses. From the proximate, ultimate and ash composition analyses it was clear that the coal used con-formed to the average characteristics measured over an extended time period. From the AFT values it was seen that an increase in the flow temperature occurred with the addition of pure elemental iron to the coal, which can be of importance for operational purposes as to raise the gasifier temperature and not to have slagging problems to occur in the gasifier. The Mössbauer data show that he-matite is the main Fe-component that forms from the pyrite originally present and from the added iron to the coal, consistent with FactSage modelling, which shows that the partial oxygen pressure determines which mineral species will form. This study opens up new possibilities when considering operational problems experienced in in-dustrial gasifiers. Successful completion of this study and a study to look at reducing conditions in the gasifier will also add to the knowledge that already exists regarding fluxing agents.

Jan 1, 2014

In this study, the effect of different regrinding conditions on the depression of fine pyrite at the cleaner stage was investigated. The regrinding condition was manipulated by different grinding media (stainless steel and mild steel). It was found that, after regrinding with mild steel grinding media, the flotation recovery of pyrite is much lower than with stainless steel grinding media, and it is more difficult to restore by adding more collector. This means, regrinding with mild steel grinding media may depress the pyrite flotation more strongly. The copper activation of pyrite during regrinding was also studied. It was found, that the mild steel grinding media is more beneficial to copper activation than stainless steel media. Additionally, the analysis of pyrite recovery based on the particle size indicated, that the fine particles are more susceptible to different grinding environments than intermediate and coarse particles and therefore are more easily depressed with a much lower flotation recovery.

Sep 1, 2012

By Braulio Fernández, Gonzalo Montes-Atenas

The mechanisms taking place during the leaching of chalcopyrite when it is in contact with other sulphide minerals, particularly pyrite, is still a matter not fully solved. The GalvanoxTM process has been suggested as a technical solution to extract copper from chalcopyrite at commercial level inhibiting passivation phenomena widely reported in the field of hydrometallurgy. Although there are some rules of thumb to implement the process in fully flooded stirred conditions such as the optimum pyrite/chalcopyrite mass ratio should range between 2 and 4, among others; not many research studies have been focused on studying the effect of the surface contact area between chalcopyrite and pyrite to reach best copper extraction conditions. The aim of this research work is to determine the effect of the mass and surface area ratio between the minerals and the surface area of each of the mineral species effectively exposed to the leaching solution. Different particle size distributions of pure pyrite and chalcopyrite were contacted in a small column and subjected to leach tests using sulphuric acid in concentrations close those used in industrial leaching processes. The mass and surface area ratios which optimize the extraction of copper were obtained. It was found the best leaching conditions were attained when reducing the particle size distribution of pyrite regardless the particle size distribution of chalcopyrite. Further analysis concerning the impact of this conclusions on large scale operations is presented and discussed.

Jan 1, 2014

By O. V. Suvorova, V. G. Minenko, D. V. Makarov, A. L. Samusev, E. A. Selivanova

"Saponite is a valuable marketable product widely used foundry, metallurgy and construction, in the chemical, food and consumer goods industries, in medicine, and in agriculture.The feasibility of producing of high-quality construction materials with enhanced physical-chemical and decorative characteristics from saponite-containing products has been given a scientific basis and experimentally validated. The compressive strength of the samples in the sintering temperature range of 800-1000 ?? varied between 35 and 80.9 MPa; the bending strength 8 and 26.7 MPa, which is superior to the high-grade ceramic bricks of the M-300 brand. It has been established that the saponite-containing product obtained using the electrochemical separation of process water has a high sorption capacitance relatively the heavy-metal ions such as nickel and copper (40.7 and 99.8 mg/g, respectively). As a result of sintering at 750 ?? the sorption capacity of the sorbent for the nickel and copper ions increased to 194.2 and 212.8. Using the XRD and SEM with energy-dispersive spectroscopy studies, we diagnosed the metal-containing phases and validated the metal sorption mechanism.This study opens up the possibility of practical realization of the saponite-containing product as high-quality building materials and heavy-metal sorbents while addressing the issue of process water treatment. INTRODUCTION The Lomonosov deposit of the Archangelsk diamondiferous province accommodates 10 kimberlite pipes. The anticipated volume of diamond-bearing ore and dump rock to be removed before reaching the open-pit mining limit is 300 mln t (Karpenko, 2009; Bezborodov, etal. 2003). Rock in the deposit is almost completely displaced by clay minerals, predominantly saponite, amounting to 90% in the vent facies (Karpenko, 2009)."

Jan 1, 2018