Search Documents

By Érica Linhares, Anderson Silveira Lopes, Aline Costa

In the production units of ferromanganese alloys wastewater are generated. They mainly arise from gutters of drainage water from warehouse of raw material (manganese ore, reducing agents and other), product and slag. This wastewater, in general, may contain particles that will suffer difficulty to naturally decant, giving the water turbidity and color characteristics. Thus, this study aims to characterize the effluent, the treated water and the sludge from the sedimentation tank from the one main Brazilian plant. The investigated characteristics were: turbidity, total solids (TS), suspended solids (SS), dissolved solids (DS), pH, Eh, COD (chemical oxygen demand), residue classification and chemical analysis by ICP - OES. The turbidity before treatment was 417 NTU and after passing through the tank, 44 NTU, a figure slightly higher than the emission standards for Class 1 regulated by the Brazilian environmental legislation in force. The values for TS, SS and DS of the effluent were 225, 114.3 and 110 mg/L, respectively. For the treated water the values were 93, 48.3 and 45 mg/L for TS, SS and DS, respectively. The sedimentation process was able to reduce by 21 % of the COD. In the test of loss on ignition (LOI) from the tank bottom sludge were observed losses of 29.35 %, while the volatile analysis found 20.70 % of volatiles in the sample. It was determined that the concentrations of Al, Fe, Mn and S are, respectively, 0.1875 mg.L-1, 0.3071 mg.L-1, 0,789 mg l-1 and 0.00828 mg.L-1, values above the maximum allowed by law. Based on the analysis of X-ray diffraction, the identified minerals in the sludge were quartz, muscovite, kaolinite, calcite and albite.

Jan 1, 2014

By Marco Le Roux, Quentin Campbell

"Most coal supply contracts include strict limitations on the moisture content of the products. This limitation exists because of calorific, transport cost, and handling reasons. Managing the retention time on product stockpiles to facilitate drainage commonly controls the moisture content in coarser coal products. A large-scale pilot rig has been commissioned to facilitate research in this regard. A stockpile of about 15 tonnes of a typical washed power station feed coal from the South African Witbank coalfield was loaded onto a 6 x 6 m platform on load cells. The platform was shielded from the elements, like rain and wind, and an artificial rain sprinkler system was installed. A variety of rainfall intensities and durations were simulated and the water accumulation and run-off was measured. The material was also sampled for moisture and particle size before and after the series of tests. At the same time, the drainage characteristics of the same coal were determined in smaller scale drainage columns for comparison. Data is presented in this paper on the drainage rates, maximum accumulated moisture, final moisture, and the effect of evaporation. The results showed that for all rainfall patterns tested, drainage ceased after 2 - 3 days, but evaporation continued for at least the time period under investigation, albeit at a low rate. Evaporation contributed to dewatering at rates that depended on wind, temperature and humidity conditions. This caused a slow reduction in moisture content even after the run-off had ceased. The value of the final moisture depended on the coal PSD. It was also found that the intensity and duration of the more intense rainfall events did not significantly affect the maximum water accumulation, with drainage rates equaling the corresponding water addition rates which suggested that water ran off over the surface of the stockpile with limited penetration. During more intense rainfall scenarios, some penetration was apparent."

Jan 1, 2014

By S. Fiore, M. C. Zanetti, C. Clerici

The processes and fluxes of a cast iron foundry plant located in the North of Italy were analyzed in order to determine the amount and kind of wastes produced from the different activities. The main fractions are the molding sands, furnace muds and powders coming from the dust abatement plant, the exhaust lime, the furnace refractory, the metallic shotting and the sludges and powders coming from the dust abatement plant of molding lines for a total production equal to 800 t/d. All wastes were sampled and particle-size and chemically characterized to evaluate the best recycling or reuse solutions. Wastes were sieved and divided in three categories according to the particle-size dimensions: below 0.1 mm, between 0.1 and 0.6 mm and above 0.6 mm. The fraction above 0.6 mm dimension underwent magnetic separation to recover and quantify the potentially available iron fraction. The fraction between 0.1 mm and 0.6 mm was chemically characterized in order to understand if it could be fed to the sand regeneration plant. The below 0.1 mm fraction was characterized to evaluate the following recycling and reuse solutions: additive for molding sands and/or raw material for the concrete industry.

Jan 1, 2003

By X. Tan

In this paper, the application of the metallurgical residue produced from oceanic cobalt-rich crusts leaching process is studied in the area of wastewater treatment. The modification of the sulfuric acid leached residue and the adsorption behavior behaviour of heavy metal ions such as (Pb(II), Cu(II), Zn(II), Cd(II), Ni(II), Mn(II), Co(II), As(III)) in the waste-water on the surface of the residue are investigated. The rate of adsorption efficiency of heavy metal ions in the wastewater on the modified sulfuric acid leached residue is investigated. It is showed that when the initial pH value of wastewater containing heavy metal ions including Pb(II), Cu(II), Co(II), Ni(II), Mn(II), Zn(II), Cd(II) and As(III) range from 1.4 to 1.9, with the use of the modified leached residue, As(III) ion can be selectively separated from wastewater, and the separation efficiency can reach 90%~100%. The adsorption efficiency is affected by pH, reaction time, amount of adsorbent and the initial concentration of heavy metal ions in wastewater. The results showed that the optimum pH was natural pH value and the absorption equilibrium time was 2 hours. The adsorption efficiency of heavy metal ions increases with the addition of adsorbent and de- creases with the increase of the initial concentrations of heavy metal ions in wastewater. The heavy metal ions polluted wastewater, of which concentration is about 22.5~793.6 mg/L, can meet the national disposal standard for industrial wastewaters in China very well, after 2 hours treated by 3.75~7.50 g/L modified adsorbent at room temperature. Standard methods were used to investaged investigate the absorption behaviour between abosorbentabsorbent and metal ions in the wastewater. It is concluded that the adsorption behaviour of Co(II), Mn(II) and As(III) ion fits Freundlich iso-therm, while the adsorption behaviour of Pb(II), Cu(II), Zn(II), Cd(II) and Ni(II) ions fits Langmuir isotherm, and the saturated adsorption amount of the modified adsorbent is about 54.0~336.7mg metal/g?adsorbentabsorbent. It is suggested that the modified sulfuric acid leached residue produced from oceanic cobalt-rich crusts is environmentally attractive and meaningful as absorbent used in heavy metal ions polluted wastewater.

Jan 1, 2014

By Stoyan Groudev

Two experimental plots consisting of a slightly acidic soil heavily contaminated with radionuclides (mainly uranium and radium) and non-ferrous metals (mainly copper, zinc, and cadmium) were treated in situ under real field conditions using the activity of some representatives of the indigenous soil microflora. This activity was enhanced by suitable changes in the levels of some essential environmental factors such as pH and water, oxygen and nutrient contents of the soil. The treatment was connected with solubilization and removal of the contaminants from the top soil layer (horizon A) due to the joint action of the soil microorganisms (mainly acidophilic chemolithotrophic bacteria) and leach solutions (diluted sulphuric acid) used to irrigate the soil. In one of the plots, the dissolved contaminants were removed from the soil profile through the drainage soil effluents and were subjected to cleaning by a constructed wetland located near this plot. In the other plot, the dissolved contaminants were transferred to the deeply located soil subhorizon B2 where they were precipitated as the relevant insoluble forms (uranium as uraninite, and the non-ferrous metals as the relevant sulphides) as a result of the activity of the sulphate-reducing bacteria inhabiting this soil subhorizon. This activity was enhanced by injecting water solutions of acetate, lactate, ammonium, and phosphate ions to this soil subhorizon.

Sep 1, 2012

By Wang Xu, Tao Dongping, Zhang Jie, Tao Youjun

Based on the principle of fly ash triboelectrification, the mineral electrical index and testing method are introduced. The electric differences of various mineral components of fly ash are discussed in view of the results of chemical and mineral composition analysis of the fly ash sample acquired from the Xin-wen power plant. The dielectric constant and charge-mass ratio of carbon and ash in the fly ash are determined. The data were then used along with the rotary triboelectrostatic separator (RTS) testing results to investigate the charging characteristic of fly ash particles in different sizes. The results show that the dielectric constant of fly ash with different particle size decreased with the decrease in particle size, which led to a poor electrical conductivity. Thus particle size has an important effect on conductivity. The charges of carbon and ash particles increased with decreasing particle size. The charge-mass ratio of carbon and ash particles of the same size increased with decreasing particle size. This indicates that finer particle size is more favorable for triboelectrification separation from the charging efficiency point of view. The rotary triboelectrostatic fly ash separation tests show that the best decarbonization performance was achieved with particles in the size range of 0.038-0.074mm with which the decarbonization rate and efficiency index reached 38.93% and 120.83% spectively.

Jan 1, 2014

By E. V. Manlapig, M. C. Harris

"The complexity of the flotation process has made the identification of an appropriate model structure for the predictive simulation of flotation circuits far from obvious. Work performed under the auspices of the AMIRA P9 flotation program has indicated that the metallurgical performance achieved from a flotation cell arises from the interaction of two essentially independent property classes, namely the cell operating conditions and the properties of the cell feed stream. These observations have led to the development of a model structure that associates a constant set of flotation parameters to the streams of the circuit, which are transformed into a flotation response depending on the operating conditions within the flotation cell.A variety of alternative model structures exist within the literature which do not make this distinction between cell and stream flotation properties, and many of these models are in widespread use for flotation optimisation and design studies, both in industry and academia.In this paper, circuit survey and laboratory batch flotation data collected from an industrial flotation circuit are analysed. The data demonstrate that streams in an industrial flotation circuit exhibit varying particle floatability – concentrate streams typically float faster than tailing streams (Figure 1(a)). This floatability, however, is generally conserved around the various units within the flotation process (i.e. the effective floatability of the combined feed and product streams of a unit is equivalent (Figure 1(b)))."

Jan 1, 2003

By Tsvetan Damyanov, Nikolay Hristov, Evgeni Kostadinov, Lubomir Kuzev

"The process of grinding in drum mills is directly dependent on the dynamic forces occuring in the free movement of the grinding bodies in the volume. The subject of discussion are the potential impacts between grinding bodies having different shape and equal weight in a drum mill that has a diameter of 1200 mm. The study utilised ball grinding bodies having a diameter of 120 mm and tetraballpebs having a conditional diameter of 120 mm. The study was carried out using the Solid Works Simulation software. The following cases were examined: • Impact between two identical grinding bodies; • Impact between a grinding body and the shell surface. The study provided numerical values for impact force, kinetic energy of impact, linear speed of impact, linear displacment of the center of gravity and duration of impact deformation. The impact force of the balls is approximately 179000 N. The impact force of the tetraballpebs with typical vertices, edges and spherical surfaces depending on the area of impact is 177000 to 185000 N. Upon impact between two spherical surfaces of tetraballpebs, the contact area is 263.55 mm2, which is more than twice the contact area upon impact between two balls, which is 114.39 mm2. This determines better conditions for the transmission of kinetic energy by reducing opportunities for overgrinding."

Jan 1, 2014

By Q. Huo

The alumina production might not continue when the sulfur content of bauxite was too high. In order to bring down the sulfur content in bauxite, we studied on the bauxite desulfurization by bacteria screened from the acid mine drainage at mines of high sulfur content. The screened bacteria were domesticated by the high sulfur content bauxite. The experiments of bauxite desulfurization were carried out under the conditions of 5% pulp density, temperature of 30?, rotate speed of 120rpm. Bacterial desulfurization for 30 days, the sulfur content of the bauxite was reduced from 5.73% to 1.55% and the desulfurization percent was 72.9%. The recovery percent of alumina was 94.3%. The study showed that it was feasible to bring down the sulfur content of bauxite by bioleaching and this technique might make full use of the low grade bauxite.

Jan 1, 2014

By M. M. Moghaddam

Charge motion is of prime importance in the efficiency of comminution in tumbling mills. Since direct observation of charge shape and its motion in industrial mill are not possible, a combination of analytical and physical studies was used to determine charge trajectory. Software packages, which predict charge motion such as the GMT (Grinding Media Trajectory) only consider the outermost layer of charge (single ball) and ignore the interactions of grinding elements. In this research, the measured charge trajectory in a 1m-diameter mill with the transparent end, called model mill, was compared with that of the GMT. Four types of polyurethane rings were accurately machined to scale down the liners arrangements at two industrial mills. To explore various charge shapes and trajectories, the model mill was operated at 55, 70 and 85% of critical speed for five levels of mill filling (10, 15, 20, 25 and 30% by volume). The angular displacement of the toe, toe departure, shoulder and charge impact point were determined from the photographs taken from the model mill. New relationships to predict charge shape and charge impact points were introduced to modify the GMT results. The relationships were validated by the model mill using the new liner of the Sarcheshmeh copper complex SAG mill. The relative error of prediction was found to be 1.1%. The results indicated that when the lifter face angle increased from 7 to 30º, the distance between the charge impact point and the toe decreased from 52 to 31º for 25% filling. This meant increasing the probability of charge impacting the toe not the liner which favoured more efficient comminution practice. After converting AG mills to SAG mills on account of liner profile change, 31% increase in throughput (from 419 to 548 t/h) in addition to 4% decrease in the product size (from 516 to 496 µm) were realized which was a significant contribution in the plant performance improvement.

Sep 1, 2012

By Wei Sun, Ruolin Wang, Jianjun Wang, Xiaodong Li, Honghu Tang, Yuehua Hu, Anh V. Nguyen, Haisheng Han, Kefeng Chen, Zhao Wei

It is difficult to separate scheelite especially from fluorite with fatty acid collectors because the adsorption mechanism of these collectors occurs through chemisorption of the oleate ion onto the mineral surface. A simplified flotation process using Pb-BHA complexes was developed to replace the energy-inefficient Petrov’s process of using a fatty acid, increasing the recovery of scheelite and reducing the cost. The relationship between surface chemical properties (crystal chemistry, solubility, and Zeta potential) of minerals and flotation by using a fatty acid or Pb-BHA complexes was studied in detail to provide new insights into the selective separation mechanism. The results indicate that the scheelite surface exposes more O atoms than Ca and that they are negatively charged due to the anisometric dissolution of Ca and WO4, which provides the possibility for separation using selective interfacial reaction. The FTIR and Zeta potential results indicate that both chemical and electrostatic adsorption play an important role in the adsorption of Pb-BHA complexes on the scheelite surface. The XPS results of the atomic composition and binding energies confirmed the presence of the adsorbed Pb-BHA complexes and that O and Ca may be the active adsorption sites. Therefore, scheelite was able to be collected by forming either a Ca-O-Pbcollector or W-O-Pb-collector (BHA). However, fluorite was only able to be collected by a fatty acid collector and colloidal [H2SiO3]n -, and a high temperature was needed improve the selective desorption of the adsorbed fatty acid collector by forming Ca-[H2SiO3]n - on the fluorite surface, resulting in serious problems in industry. However, the Pb-BHA complexes significantly contribute to improving the recovery of scheelite minerals, simplifying the flotation process, and circulation of the residual reagents and water. The new process has been applied in Shizhuyuan Mine, and improved the recovery by almost 10%.

Jan 1, 2018

By Graeme Heyes, Warren J. Bruckard, Michael A. Somerville

"A limited series of laboratory batch flotation tests was conducted on a suite of calcium-ferrite-based slags made in laboratory smelting trials. The smelting tests were conducted as part of a wider CSIRO Minerals’ research project aimed at developing a single-stage continuous copper-making process. The objective of the flotation work was to maximise copper recovery and iron rejection from slags made in the process.The slags treated included a reduced low copper slag, an oxidised high copper slag composite, and a very reduced low copper self-pulverising slag. The copper content of the slags varied from 2.9% to 14% Cu. The copper was present as metallic copper, oxide copper and copper-calcium ferrite phases with the phase mix related to smelting conditions. The slags were crushed, ground, wet-screened at 355 or 210 µm to remove coarse metallic particles of copper, and floated at natural pH (about pH 11) using reagents and conditions appropriate for the selective recovery of the copper phases.In rougher/scavenger tests on the reduced low copper and self-pulverising slags copper recoveries above 92% were obtained with copper enrichment ratios varying between 2.3 and 2.9. For the oxidised high copper slag copper recoveries were poorer - only 47% of the copper was recovered with an enrichment ratio of 3.3. The presence of the slow floating copper-ferrite phases in the slags limited further (selective) copper recovery. Ageing of the high copper slag, that is, a significant delay between grinding and flotation, resulted in a deterioration of the copper flotation response.The critical parameter affecting the flotation of copper from direct converting slags was found to be the form of the copper in the slag. Slags containing a higher proportion of the more desirable form of copper for flotation will provide the best opportunity for high copper recoveries to be consistently obtained, allowing improvements in the economics of the overall copper-making process."

Jan 1, 2003

By Fedotov. K. V., A. Y. Senchenko, V. A. Chanturiya

"The paper describes an efficient process to treat the ore from the largest in Russia copper deposit – Udokan. The recommended process is universally applicable to Udokan ores different in composition and allows reaching high copper recoveries during production of high-grade cathode copper and sulphide concentrate with 45% copper content. There are several promising trends for the process optimization and in the case they are implemented, economics of the whole project could improve significantly. One of the most important optimization options implies reduction of specific energy consumption in the course of comminution operations. Another possible option to optimize the already selected process flowsheet is production of cathode copper from sulphide concentrate directly at a mining and metallurgical plant without sending the latter to other metallurgical works.INTRODUCTIONUdokan copper deposit with resources of more than 20 million tons of copper is the largest in Russia and one of the largest copper deposits in the world. The deposit is located in Kalar District of the Trans-Baikal Territory, 30 km away from Novaya Chara railway station of the Baikal-Amur Mainline.Scientists and engineers from various research institutions have studied Udokan copper ores for years. Along the way, some conceptual process flowsheets have been proposed and each of them has its own pros and cons. The key requirement to the processes being developed was their universal application for processing of all the ore types using a single flowsheet. Due to the hard mining and geological conditions and because of complex material composition of Udokan ores it is of great difficulty to design a process which would provide for maximum economic benefits. That is why the process optimization has been ongoing until now.According to the Russian standards, the main input document for design of a metallurgical plant is referred to as a Process Design Report that covers the following key data sections: analysis of metallurgical testing results, validation of the process, design criteria, process flow diagrams, the mass and metallurgical balances, process description, equipment list and other information necessary for the subsequent design."

Jan 1, 2018

By P. Han

The preparation technological conditions and regeneration method of two novel granulated adsorbing materials of rectorite/fly ash composite (Material 1) and rectorite/water quenched - slag composite (Material 2) and the use of them to remove heavy metals from copper smelting plant wastewater have been studied. The experimental results showed that under the preparation conditions with the ratio of rectorite to fly ash or water - quenched slag of 1:1, the amount of the additive (Industrial Starch, IS) of 15% (Material 1) or 10% (Material 2), the addition of 50% water, and the calcination temperature of 500? (Material 1) or 400? (Material 2), the efficiency of heavy metal removal with the granulated materials was the best, whereas the ratio of disintegration loss was the lowest. Under the treatment conditions of natural pH, and with the addition of the granulated materials of 0.07g/cm3 (Material 1) or 0.05g/cm3 (Material 2), a reaction time of 60 minutes (Material 1) or 40 minutes (Material 2), and the adsorption temperature of 25?, the efficiency for the granulated materials to remove Cu2+Pb2+Zn2+Cd2+ and Ni2+ from the copper smelting plant wastewater was 98.9, 97.5, 96.7, 90.2, and 79.1, (Material 1) or 98.2, 96.3, 78.6, 86.2, and 64.2, (Material 2), respectively, and the quality indexes of the wastewater after treatment conformed with the first level of integrated wastewater discharge standard (GB8978-1996). When the adsorption of heavy metal ions on the surface attained saturation the granulated materials could be regenerated by washing with 1 mol/L sodium chloride (NaCl) solution and still with quite good heavy metal removal efficiency. The granulated adsorbing materials had the advantages of high efficiency of wastewater treatment, easy method of solid-liquid separation and regeneration, and a broad prospect of applications.

Jan 1, 2014

By Peter J. Scales

The recovery of water for re-use in minerals processing is an important issue in the reduction of water use in mining, as is the dewatering of tailings to reduce the propensity of ?wet? tailings dams. It is common in these dewatering operations to use thickeners whereby polymeric flocculants are combined with the dilute feed to the thickener to aid sedimentation and the subsequent consolidation of particulate materials. Thickeners are the workhorses of water recovery and tailings dewatering and although the basics are well understood, there is still no ability to reliably predict the throughput and underflow density from a thickener based on traditional sedimentation tests and flux analysis. The reasons for the discrepancy between full-scale operations and predictions based on laboratory tests are numerous, including difficulties in mimicking the flocculation conditions experienced in the field and the shear conditions in the thickener. The latter effects are little understood and hard to quantify and include effects due to flocculated aggregate densification, complimentary shear and compressional effects and aggregate break-up. Developing a set of test protocols to quantify the effects of densification, shear in compression effects and aggregate breakup and the subsequent contributions of each to compressional dewatering in a thickening environment has been completed for a simple model polymer flocculated particulate suspension. The data and analysis shows that aggregate densification is a dominant contributor to the difference between observed and predicted behavior based on laboratory tests. A major consideration in the analysis is the fact that common thickener operations are permeability limited and although the various effects are all important, the one that results in the fastest water release is dominant. Of interest also are the shear rate, concentration, and time dependence of the aggregate densification process. A basic model of the process has been developed along with network yielding tests conducted using rheometry. Keywords: compressional dewatering, gravity thickening, rheometry, aggregate densification, raked batch settling

Sep 1, 2012

By Gregory Harbort, Sarah K. DeBono, Alan J. Monaghan, Emmanual V. Manlapig

"The Jameson Cell is a type of flotation machine in which air and pulp are brought together in a vertical tube called a downcomer. Within the downcomer the air and pulp are dispersed into a dense foam of fine bubbles, which creates a favourable environment for bubble-particle collision and subsequent collection of hydrophobic particles. The intense collection zone within the downcomer can be considered similar to the zone between the rotor and stator in mechanical flotation cells.Research into the bubble-particle collision and fluid dynamics of mechanical cells rotor-stator zone has been limited by the difficulty of achieving accurate measurements in production sized machines. With the Jameson Cell the downcomer is largely external and separated from the flotation tank, allowing ready access to the primary contacting zone for measurement and analysis.An investigation has been undertaken into the operating characteristics of the downcomer relating to bubble-particle collision. An effective mapping of the downcomer has been made through measurements of void fraction and bubble size taken across cross sections of the downcomer. Analysis of these measurements has provided an interpretation of the variations in the air and fluid dynamics, bubble size and distribution throughout the downcomer chamber.Existing models of bubble-particle collision efficiency are reviewed in respect to the collected information and refinements conducted. The area of maximum bubble-particle collision efficiency is defined. Findings are related to operation within the rotor-stator zone of mechanical flotation cells."

Jan 1, 2003

By John Starkey

"The development of the SAG Power Index (SPI) Test in Canada has created a new and accurate way to measure ore hardness in a SAG environment. Coupled with the standard Bond Ball Mill Work Index Test it is now possible to determine from these two relatively inexpensive laboratory tests, the amount of energy required to grind an ore from the primary crushed size to the desired liberation size. By testing multiple samples to discover where the hard and soft ore zones are located, the representative hardness distribution for the ore body can be determined and grinding equipment selected that is capable to meet production targets for all mining areas of the deposit.Previously, it was deemed prudent to select up to 50 t samples of ore for Semi Autogenous Grinding (SAG) pilot plant tests and a second 5 t sample for metallurgical pilot plant work. The methods outlined in this paper show how the 50 t sample is no longer required for SAG design because it is better to measure the representative hardness distribution of the ore body than the hardness of a “chosen” representative sample. This is demonstrated to be true by the fact that the lower horizons of an ore zone cannot initially be accessed to recover 150mm pieces, and the bulk samples taken, rarely represent the desired design hardness of the ore. Median hardness will not yield a good result in most cases and a clear understanding of the location and extent of the hardest zones is imperative to achieve a truly successful grinding circuit design.This paper discusses two plants (Kubaka and Agnico Eagle) that have been designed using SPI and Bond with no pilot plant test backup. Both have been very successful in that they can grind design tonnage on the hardest ores in the mine. This guarantees that the mine’s profitability is protected in any mining sequence. It also allows the extra power to be converted to higher throughput on softer ores if additional cash flow is needed. The advantages from the owner’s point of view are dramatic. This procedure will be attractive as well when considering the costs for test work, and the samples for testing. Existing diamond drill core is normally used and this allows the inclusion of data from the deepest regions of the mine. In addition, it is also clear that the decision to use a crusher can now be made at the design stage of a project based on measured parameters and the estimated capital costs of alternative designs."

Jan 1, 2003

By Renato Oliveira, Walter Valery, Alex Jankovic, Birol Sönmez

"The ball mill is the most common ore grinding technology today, and probably more than 50% of the total world energy consumption for ore grinding is consumed in ball mills. On the other hand, high pressure grinding roll (HPGR) technology is relatively new to the mining industry, with significant application only since the beginning of the 21st century. Both ball mills and HPGRs are typically used in closed circuit with classifiers. There is a general consensus within the industry that classification efficiency and circulating load both have a major effect on the efficiency of closed circuit ball mills. Metso Process Technology & Innovation (PTI) conducted a laboratory test program to understand the relationship between classification efficiency and circulating load, and the impact on the performance and capacity of ball mill circuits. However, the effects on HPGR performance are significantly different. Metso PTI has initiated a pilot scale test program to evaluate the size reduction performance of the HPGR under different circuit configurations. A series of pilot scale HPGR locked cycle tests were performed to simulate the following circuit configurations: including closed circuit with a screen, partial product recycle and edge recycle. This paper discusses the results from the pilot scale HPGR and laboratory scale ball mill test programs. The effect of circulating load and classification efficiency on the performance of ball mill circuits is compared to the effect on HPGR circuits. The fundamentals of grinding behavior are also discussed in order to explain the difference."

Jan 1, 2014

By Yuliy Rubinstein

"The paper presents a analysis of the history and the trends of development of flotation apparatus. The laws of their evolution are stated and the place and role of column flotation are indicated. It is demonstrate development and different design of column apparatus. The major parameters of column cell such as diameter and height are discussed. Options are proposed on optimization of hydrodynamic characteristics of columns with large-capacity cells. High efficiency of columns with cell height of 4-6 m is shown on examples of coal preparation. A new generation of multi sectional column cells has been developed. In the cells are zones with different aerohydrodynamic parameters: combined in the machine are co-and counter- counter flows of phases. The transition from single-chamber column to multi-sectional apparatus makes it possible to create favourable hydrodynamic and aeration regimes in each section of the column dependent on the pattern of material distribution by floatability. Efficiency of application different designs column apparatus uses shown on the example of enrichment of various non-ferrous metals ores and coal. The principles of mathematical simulation of the flotation process are developed. A scaling-up procedure for column cells was based on flotation macro- and micro- dynamics simulation.INTRODUCTIONColumn flotation is considered to be one of the most significant achievement in the field of mineral processing in the end of last century. We cannot but agree with this statement but would like to understand what underlies this success. History of the flotation column can not be considered in isolation from the development of flotation apparatus on the whole. It can be argued that the first attempt to switch from oil flotation to the use of bubbles during flotation was performed Bessel brothers in 1877 (Berlin patent 42 class 22, July 2) and in 1886 (Berlin patent 39,369 May 12). According to these patents, the crushed ore was mixed with oils , hydrocarbons and water. Then the pulp received in this way was heated up to boiling . Air bubbles and steam formed during boiling facilitate the flotation of ore particles coated with oil (first patent) or bubbles been generated by the reaction of lime with acid (second patent). The evolution in the design of the flotation apparatus incorporates the following key stages. Further development is connected with the Francis Elmore’s idea to use gas bubbles received at water electrolysis (UK, 13578; 1904). This method was not introduced then, but much later, in our time and on the essentially new technical basis it found a use for sewage treatment (electroflotation). Gas bubbling under vacuum patented also by Elmore (UK, 17816; 1904) obtained a practical use. It should be noted that the method did not lose its importance till now. The design of the camera has been surely optimized (Glembotskii etal, 1963). A year later A. Macquisten (UK, 26712) developed pressure (compression) flotation. Thus, the H.Sulman, H.Picard, D. Bell’s (US, 853120, May 29, 1905) basic patent and the adjoining T. Goover’s patent 1910 (US, 953746) formed the basis of the first and most important element of modern flotation: flotation with air bubbles sucked in from the environment. In 1914, J.Callow received a patent for on an apparatus where air was sparged through the porous false bottom of the cell ( US, 1104755). Woolen fabric folded four times was fixed on a perforated metal frame to be used for air sparging (Gaudin, 1932). The following year Durrel created the prototype of the injection (ejector) apparatus. The jet aerator made it possible to significantly reduce the size of the bubbles, in comparison with the filter cloth. An apparatus with slurry pre-aeration in an airlift prior to feeding into separation cell was developed Wagner in 1917 (US, 1235083). And finally, the first column apparatus with a counter-current of slurry and air was developed by M. Towne and S. Flynn in 1919(US, 1,295,817). ("

Jan 1, 2018

The flotation efficiency of magnetic concentrate of the Anhui hematite ore, which includes a great quantity of iron-bearing silicates, has been studied through reverse flotation test with a new type of collector Fly-102. The results indicate that collector Fly-102 has a strong adaptability to the variation of temperature, when the flotation temperature is in the range of 10? to 35?, using collector Fly-102 can obtain good flotation indexes. Collector Fly-102 has a strong adaptability to the variation of the slime contents and grades of the flotation samples. When the content of slime and the grade of the flotation feeds are 30% and 55.63% respectively, under the condition that the temperature is 15?, the open circuit flotation test was carried out with collector Fly-102. After one-stage roughing, one-stage cleaning and two-stage scavenging, a better result is got, the grade of iron concentrate reaches 67.12%, and the recovery of iron concentrate comes up to 84.15%.

Sep 1, 2012