Search Documents

By S. Groudev

Acid drainage waters generated in the uranium deposit Curilo, Bulgaria, were treated by means of a pilot-scale passive system consisting of a permeable reactive multibarrier and a constructed wetland connected in a series. The multibarrier had a total volume of 23 m3 and consisted of an alkalizing limestone drain and an anoxic section for microbial dissimilatory sulphate reduction, bio-sorption and additional chemical neutralization. The waters had a pH in the range of about 2.5 ~ 4.0 and contained radionuclides (uranium, radium), heavy metals (copper, zinc, cadmium, lead, nickel, cobalt, iron, manganese), arsenic and sulphates in concentrations usually much higher than the relevant permissible levels for waters intended for use in agriculture and/or industry. The water flow rate through the multibarrier varied in the range of about 1 ~ 17 m3/24 h, reflecting water residence times of about 300 ~ 18 hours. An efficient removal of pollutants was achieved by the multibarrier during different climatic seasons, even during cold winter days at external air and water temperatures close to 0oC. The multibarrier effluents were enriched in dissolved organic compounds and in some cases still contained manganese and iron in concentrations higher than the relevant permissible levels. These pollutants were removed in the constructed wetland as a result of the activity of different heterotrophic microorganisms, including some bacteria able to oxidize the bivalent manganese and iron ions to Mn4+ and Fe3+, respectively.

Jan 1, 2014

By Alejandro Uribe-Salas, Fabiola Nava-Alonso, Gloria Dávila-Pulido

This paper presents results of an experimental study performed on the role of calcium sulfate present in flotation water on sphalerite flotation in the Pb/Cu circuit (non Cu-activated sphalerite) and in the Zn circuit (Cu-activated sphalerite). In the Pb/Cu circuit calcium ions adsorb on the negatively-charged sphalerite favoring xanthate adsorption and therefore making sphalerite floatable; experimental measurements show sphalerite contact angle increases with calcium concentration while xanthate adsorption onto sphalerite increases with the increase of pH and calcium concentration. Gypsum (CaSO4·2H2O) eventually present due to calcium sulfate precipitation is not detrimental to flotation at this stage since it is negatively charged at pH 9 and therefore, does not adhere onto the surface of negatively-charged sphalerite. In the zinc circuit, Cu-activated sphalerite decreases its negative charge (or even becomes positively charged) and develops some hydrophobicity due to the polysulfide produced by Cu-activation. At this stage calcium ions do not interact with the mineral surface and therefore do not favor xanthate adsorption; nevertheless, precipitated gypsum particles do adhere onto the mineral surface, greatly affecting its floatability (e.g., contact angle). Addition of sodium carbonate to dissolve gypsum and to precipitate calcium as calcium carbonate, which disperses in the bulk of the suspension, effectively restores mineral hydrophobicity. SEM observations coupled with EDS analysis clearly illustrate and support the above sequence of events.

Jan 1, 2014

By Áureo Del Vecchio, Lídia Dely Alves de Sousa, José Pereira

The potassium demand for agriculture purposes has increased in Brazil, which has great deficit of internal demands. Potassium-rich rocks have been used as fertilizers as technological alternatives for agriculture aimed to reduce the amount of chemicals and the sector dependence for such products. Vermiculite tailings from União Brasileira de Mineração - UBM, at Santa Luzia - PB, was studied aiming their application in agriculture by potassium release. The sample was analyzed by XRF and XRD; studies on release kinetic with particles smaller than 2 mm added of organic acids (citric and oxalic) at 10-2 mol/L concentration; samples were analyzed by XRD after kinetic assays. The work was conducted using a shaker incubator at 300-rpm agitation and time variation to better understand the potassium availability in the ground. Results show the presence of K2O at 3.46% concentration. Citric and oxalic acids increased the release speed to almost the same level with speed coefficients (k) of 2.61x10-2 h-1/2 and 2.55x10-2 h-1/2 respectively. In statistical terms for both acids, the linear equation represents more than 99.0% of the experimental assays. Stonemeal was applied to banana seedlings in experiment conducted in a greenhouse. The use of vermiculite tailings in banana seedlings promoted potassium absorption, which influenced its growth. The amount of potassium liberated from vermiculite tailings could be used as a long-term alternative to fertilizers in agriculture cultures.

Jan 1, 2014

The multiphase reactive flow in process equipments, e.g., fluidized beds, involves complex coupling among flow, heat/mass transfer and reaction kinetics over scales ranging from molecules, sub-particle eddies up to equipments. Conventional two-fluid model (TFM) ignores the effects of meso-scale structures, and hence is not suitable for describing the intrinsically multi-scale heterogeneity within multiphase systems. To be consistent with the meso-scale structures, we proposed a structure-dependent multi-fluid model (SFM), and closed its drag force by invoking the stability condition defined in the energy-minimization multi-scale (EMMS) model. The SFM reduces to the conventional TFM if homogeneous distribution is assumed within each grid, and reverts to the original EMMS model if it is used to describe steady state, global behavior of a fluidized bed. The multi-scale computational fluid dynamics (CFD), which is characterized by coupling of TFM and EMMS drag coefficient, can then be viewed as a simplified solution of the SFM. We demonstrate that the SFM significantly improves the accuracy and at the same time enables higher efficiency by allowing for much coarser grid used than in TFM. Recent application of it in 3D, full-loop, transient simulation of industrial processes, e.g., fluid catalytic cracking, coal combustion, gasification, kaolinite clay calcinations, shows its advantages in helping design and troubleshoot multiphase process equipments. Keywords: meso-scale, SFM, multiscale, CFD, simulation, structure, EMMS, multiphase

Sep 1, 2012

By Imre Gombköto, Zoltán Pap, Ákos Debreczeni, Sándor Nagy

Eddy current separators have become generally used in waste recycling industry during the last decade. There are many papers dealing with separation processes on eddy current separators, and also many article describes particle trajectory and different particle features affecting particle trajectory. These data are used in modeling as well. Within the frame of R&D project called ‚Fundamental research into the exploitation of the economic development potentials of critical raw materials in international co-operation - CriticEl?, authors are aimed for using Eddy Current Separator (ECS) as a mechanical separation step of high value critical elements recovery of selected WEEE’s like display panels, PCB’s. ECS, equipped with 305 mm wide belt, and a concentric magnetic rotor is used for experiments targeted development of methodology for determining separability of different particles on ECS. The subject of our work was to investigate the behavior of model particles with different shape, conductivity (aluminum and copper), orientation and size in order to separate Al and Cu according to the results of many experiments were carried out in this field. However it looks like that throwing distance of one particle is only possible to describe by a certain distribution for even the same particle within the frame of the same conditions. Sample mean and standard deviation are depending on some of the particle feature and acting forces. The paper is going to draft the first results on the relationship between distribution of throwing distance and particle properties.

Jan 1, 2014

By Olli Haavisto, Heikki Häkkänen, Tommi Kauppinen, Navid Khajehzadeh

Raman analysis is a well-established method for finding the abundant minerals in an ore sample. In this study, Raman spectroscopy is tested as a method for rapid and contactless on-line mineral analysis. Rapidness might enable on-site analysis of rock drillcore, which in turn would lead to more cost-efficient solutions in mineral exploration. This paper discusses the use of Raman analysis to identify minerals and to measure their concentration. The sample set under study consists of rock drillcore collected from Agnico-Eagle Kittilä Mine, Finland. Selected parts of the sample set are measured by Raman spectroscopy and the minerals are identified using reference spectra from a public source. Moreover, the direct measurement of concentration of different minerals with the help of Non-negative least squares (NNLS) optimisation algorithm is considered. The optimisation algorithm was constructed to form a linear combination of reference spectra which best represent the measured spectrum, or an average of measured spectra, from an ore sample. The results show that NNLS can identify abundant minerals in a given sample. Also through this method of analysis the results of a traditional point-count method can be expanded: It was observed that, due to grain size, multiple minerals consistently appear in the spectra measured over an area, which means that point-count method is not a proper way to interpret the spectra. This can be seen as a new result, as formerly the discussion has attended to other methods.

Jan 1, 2014

By B. J. Zhang

Conventional spirals are capable of providing excellent clean coal recovery, although at a relatively high ash content. Compound spirals, which provide two stages of spiral cleaning in a single taller unit, have been commercialized in recent years to improve upon the cleaning performance obtained from conventional spirals. The present study aimed at optimizing the performance obtained from a compound spiral for cleaning especially high sulfur fine and ultrafine coal. Industrial-scale spiral units were utilized for this study in a pilot-scale facility at the Illinois Coal Development Park. A statistically designed experimental program was conducted to optimize ash and sulfur cleaning performance of the compound spiral. It was found that significant cleaning of ultrafine coal (i.e., 150 microns × 45 microns and even 45 microns × 25 microns size coal) is achievable with the compound spiral. However, operating conditions for cleaning finer coal fractions (-150 microns size coal) have to be significantly different from those used to clean coarser coal fractions (+150 microns size coal). The sulfur rejection trends were different from ash separation efficiency trends in all size fractions except 45 microns × 25 microns. The probable error (Ep) and effective specific gravity of separation (SG50c) determined for the compound spiral cleaning of the overall particle size were as low as 0.07 and 1.62, respectively. However, the bypass of a small percentage of clean coal to the tailings stream of the compound spiral, may need further adjustment of the key process parameters.

Jan 1, 2014

By Arkady Senchenko, Sergey Rybkin, Svetlana Lagutina, Alexander Aksenov

"The application of autoclave leaching technology for sulfide concentrates containing base and precious metals is spreading nowadays. In the process of concentrate leaching silver accumulates in the forms of jarosite compounds, transforms into passive chemical state and is mostly found in solid phase. Effective technology development for silver recovery from solid phase of concentrate autoclave leaching raises the necessity for comprehensive research of silver forms of occurrence and their properties in this product. The possible form of silver presence in solid phase of concentrate from autoclave leaching is argentojarosite. This article is about the study of physical and chemical properties and structure of synthetic argentojarosite - AgFe3(SO4)2(OH)6. A method of argentojarosite synthesis has been developed under conditions simulating the process of autoclave leaching of sulfide concentrate, and includes silver dissolution in the form of Ag2SO4, Fe3+ sulfate hydrolysis, AgFe3(SO4)2(OH)6 build-up. X-ray data of synthesized argentojarosite completely correspond to those of natural mineral. The structural formula of this complex compound has been studied and confirmed. The chemical properties of synthetic argentojarosite, its solubility in acids and alkalis have been investigated. Phase changes when heating argentojarosite with the build-up of iron oxide and silver sulfate stop at the temperature equal to 650 ºC. Based on the results received the technological solutions for solid phase of autoclave leaching of concentrate have been developed with silver recovery of 95-98%."

Jan 1, 2014

By C. Dorfling, P. Albertyn

"Hydrometallurgical recovery of metals from printed circuit board waste typically involves multiple leaching stages; conventionally, base metals dissolution by mineral acids is followed by leaching of gold using cyanide or halide based lixiviants. Alternative lixiviants for gold leaching can reduce the potential hazardous nature of operation. The aim of this study was to investigate the feasibility of using thiosulfate as lixiviant for gold leaching from waste printed circuit boards. Batch leaching tests were performed to investigate the effects of thiosulfate concentration (0.1 – 0.2 M), ammonium concentration (0.2 – 0.4 M), pH (9 – 10.5), solids content (25 – 50 g/L), and copper content of the feed material on the gold leaching behavior. The concentrations of metals in liquid samples were determined by means of inductively coupled plasma atomic emission spectroscopy, and high pressure liquid chromatography was used to evaluate thiosulfate degradation/consumption. The ratio of thiosulfate to ammonia was found to have the most significant effect on the extent of gold leaching, with the best gold extraction observed at a ratio of 0.5 mole thiosulfate per mole ammonia. The lower pH range of 9 – 9.5 generally produced better Au leaching, while low copper extraction during the first stage base metal leaching stages has proven to be detrimental to gold leaching from the residue. Thiosulfate degradation/consumption increased and gold extraction decreased with higher residual copper in the feed. An optimum gold extraction of 78.5 % from base metal leach residue was achieved with 0.2 M thiosulfate, 0.4 M ammonia, and 0.02 M cupric ions at 25°C in the pH range 9 – 9.5.INTRODUCTION Background and Aim The recycling of e-waste is becoming increasingly important as it provides certain economic benefits apart from the obvious environmental benefits. Printed circuit boards (PCBs) are found in most forms of e-waste and contain especially high concentrations of base and precious metals. Hydrometallurgical processes are often considered for the recovery of valuable metals from PCBs; these processes normally implement several leaching stages to selectively recover certain metals."

Jan 1, 2018

By B. McFadzean, S. Geldenhuys

"Dynamic froth stability tests have found widespread application to quantify froth performance. However, little to no attention has been given to scale parameters in the performance of these measurements. One of the most frequently changing scale parameters in the laboratory scale is the column diameter as this directly influences the amount of material needed for testing. Four different column diameters (50, 100, 200 and 300 mm) were used for this study. Column diameter experiments were done on an industrial scale by means of manual tracking of froth growth versus time. An increase in measured dynamic stability was seen with increasing froth column diameter, which reached a limiting value at large column sizes. It is thought that this behaviour is controlled by the differences in drainage rates of the bulk froth compared to froth in contact with the wall. The column diameter required to represent full-scale froth stability is proposed. A ratio of column surface area to total bubble surface area was used to correct for different column diameters.INTRODUCTIONThe froth phase in flotation contributes significantly to the overall performance of the process (Zanin, et al., 2009). Numerous parameters have been investigated to quantify froth performance, most notably froth recovery (Feteris, et al., 1987; Seaman, et al., 2004; Vera, et al., 1999). Experimentally gathering data to determine froth recovery is challenging and for this reason froth stability has been highlighted as a possible alternative.Froth/foam stability is defined as the time of persistence of the froth/foam and is affected by numerous factors, such as: drainage of the liquid in the lamellae (gravitational and capillary), viscosity at the bubble surface, thickness of the electrical double layer and gas diffusion through liquid films caused by pressure differences between bubbles (Aktas, et al., 2008; Beneventi, et al., 2001). It is well documented in both froth and foam literature that froth/foam stability will heavily influence the performance and appearance of the froth/foam phase (Ata, 2012; Farrokhpay, 2011; Weaire, et al., 2005). Experimentally this has been explicitly proven as an increase in froth stability, characterised by water recovery, usually results in an increase in both valuable mineral and solids recovery (Wiese, et al., 2011; Banford, et al., 1998)."

Jan 1, 2018

By I. A. Makalin, V. N. Yakovlev, S. V. Imangulov, I. V. Zyryanov

"The presented studies aimed at solving the problem of recovery of low-luminescent diamonds, which are not recovered using X-ray luminescence method of processing of diamond-bearing ore. The purpose of the studies is the determination of possibility and feasibility of recovery of such crystals using dual-energy X-ray transmission separation technology. In preparation for studies methods were developed for testing technical and process parameters of XRT-400 Aliud GmbH (Germany) sorter, manufactured according to design specifications of Yakutniproalmaz Institute, and XRT/D TOMRA Sorting Solutions GmbH (Germany) sorter, designed for processing of -50+5 mm ore, as well as RGS-1M, RGS-2 X-ray sorters, developed by JSC NPP Bourevestnik (St. Petersburg) in cooperation with Yakutniproalmaz Institute, for material size of -6+3 mm. In 2018, in-process tests of RGS-OD-3 X-ray sorter prototype on material size of -3+1 mm are scheduled. Studies to determine the content of low-luminescent diamonds and feasibility of their recovery using XRT-400 and XRT/D sorters at the Processing Plant #3 of Mirny Mining and Processing Division (MPD) were carried out. The results of the studies confirmed presence of such diamonds and possibility of their recovery using the dual-energy X-ray transmission method. In-process tests of RGS-2 X-ray graphic sorter were carried out at the Processing Plant #16 of Nyurba MPD. According to the results of sampling of RGS-2 sorter separation products, the recovery of -6+3 mm sized diamonds from tailings of X-ray luminescence sorters was achieved at the level of 96%, while the diamonds recovery was 98.5% in value terms, the concentrate yield was 0.1%. In-process tests of RGS-1M sorters at final recovery of the grease separation concentrate at the Processing Plant #3 of Mirny Division were carried out. Recovery of low-luminescent -6+2 mm sized diamonds by RGS-1M sorter amounted to 92.4% for single operation, and with the double control operation reached 99%. As a result, -6+2 mm sized base product recovery increased by 0.2%."

Jan 1, 2018

By N. P. Haran

A detailed study was undertaken to beneficiate sub-grade iron ore sample from Kenojhar District, Orissa, India containing 57% Fe (T), 7.7% SiO2, 4.8% Al2O3, 4 % L.O.I. 0.4% TiO2,1.3 % Mn and traces of S(T) to make it suitable for the user industry. The mineralogical study indicated that it predominantly consists of haematite with subordinate amounts of goethite and clay. Quartz, Cryptomelane / Psilomelane, Pyrolusite, Gibbsite, Feldspar and Muscovite mica were present in very minor to trace amounts. The Denver grind ability tests indicated, that the sample could be categorized as ?medium soft to medium.? The Bond ball mill work index was determined to be 14.19 kwh per short ton. The beneficiation process involved classification followed by tabling of the classified sand, ground to minus 48 mesh size. The table slimes were subjected to Wet High Intensity Magnetic Separator (WHIMS). The developed process yielded a composite concentrate from tabling and WHIMS operations assaying 65% Fe(T), 2% SiO2, 1.8% Al2O3, 2% Mn and 0.9% LOI with a recovery of 60.1% Fe (T), amounting to 52.5 wt.% yield. To meet the size specifications for pellet making, it was further ground. Dewatering studies were also carried out on the ground combined concentrate and rejects. The thickener area of ground combined concentrate using 0.02 kg/t of Sufloc A 1115 flocculant was 0.02 m2/tonne of dry solids per 24 h. And for the combined rejects using 0.12 kg/t of flocculant, it was 0.035 m2/tonne of dry solids per 24 h. The moisture content, in the pressure filtration cake, in the ground combined concentrate product was 10.0%, and productivity was 506.7 kg/m2h. Thus, by thickening and filtration of process products, 90% of water used in the process could be recovered. The study highlights the development of a simple and cost effective flowsheet with almost complete water recovery for a subgrade iron ore sample. Keywords: tabling, WHIMS, thickener, filtration

Sep 1, 2012

By S. Chuanyao

In last decade, along with its booming Chinese economy, China?s higher education has experienced rapid growth. In 2010, the number of various colleges totals more than 3500, with 2.2 million faculties registered. Currently there are almost 30 million students studying in the colleges, 3 times more than 10 years ago. Mineral Processing was initiated in 1949 as a sub-discipline of Mining Engineering, one of the 13 first level disciplines. Mineral Processing is now established in 34 Chinese colleges, recruiting 2600 undergraduate students, 540 postgraduate students and 100 PhD students every year. A further 9 institutes offer postgraduate education in this field. More than 3000 graduates majoring in Mineral Processing join the industry or institutions each year. The four-year undergraduate teaching and practical training in the colleges is designed to produce qualified mineral processing professionals. This includes courses in mathematics and natural science, fundamental engineering and basic and specialization courses. Recently, the ?Excellent Engineer Program? was launched to strengthen students? practical capabilities. This is a 3+1 teaching and training model; 3 years of theoretical course study plus 1 accumulated year of various practical studies, either inside or outside the college. As for graduate employment, mining-related major graduates have been in a good demand thanks to the intensive investment in mineral sector by Chinese companies. The shortage of experienced metallurgists generates a greater than 90% employment rate for Mineral Processing graduates. However, the biggest problem we are still facing is the gap between the quality of the graduates and the requirements of industry, as a result of occupation attraction, teaching systems, faculty quality, and so forth. Another problem is international orientation. Although nowadays Chinese-foreign cooperation in college education is popular, collaborative mineral related projects are far less common, leaving much room for improvement. Looking ahead to the next 10 years, we still have the right reasons to estimate continued prosperity in the minerals sector as well as mineral processing education in China. A brief analysis and views on this will also be shared in the presentation. Keywords: China, mining engineering curriculum, excellent engineer program

Sep 1, 2012

By Mikhail I. Khersonskaya, Mark I. Mantsevich, Andrey V. Tarasov

"Due to depletion of the existing ore deposits the content of non-ferrous metals in produced ores has an inevitable tendency to decrease. Processing of low-grade ores is associated with production of low-grade selective concentrates and poses serious problems for the non-ferrous industry relating to increasing losses and expenses for waste treatment and disposal.The main component contaminating selective concentrates is iron sulphides.Copper-nickel, copper-zinc and polymetallic ores have been discussed as most important types of ores requiring removal of iron sulphides.One of the promising directions for development of selective flotation technology is the use of lowmolecular organic depressors. An advantage of organic compounds is in the possibility of multi-variant structure of organic molecules, which permits selection of a most efficient reagent for the given conditions. Another way for improving the grades of concentrates is concentration of valuable constituents associated with iron sulphides in an intermediate product and upgrading of the latter by chemical and metallurgical techniques.In order to remove iron from nickel concentrates, specific process conditions have been developed for selective flotation of pentlandite with the use of an organic depressor for pyrrhotite. The use of a depressor for flotation of high-grade copper-nickel ores ensures an increase in the nickel content up to 14% in the nickel concentrate produced as compared with 7% when using conventional process conditions, along with a nickel recovery improved by 2-3%."

Jan 1, 2003

By John A. Rumball, Martin R. Houchin

"For gold leaching of oxide ores, the optimum cyanide : oxygen ratio is approximately 106 mg/L NaCN : 10 mg/L O2 (6.9:1 by mole). In sulphide ores, galvanic coupling of the gold with the electrically conductive sulphides significantly increases this ratio such that leaching may occur in a relatively low dissolved oxygen (DO) environment.RESULTS AND DISCUSSIONGold leaching in a carbon in pulp (CIP) and carbon in leach (CIL) circuit is driven by the supply of cyanide and oxygen, as described by Elsner’s equation (1):• 4Au + 8CN- + O2 + 2H2O ? 4Au(CN)2 - + 4OH- (1)Equation 1 suggests that the ideal molar cyanide : oxygen ratio should be 8:1, or 122.5 mg/L NaCN to 10 mg/L of DO. It is generally accepted however, that oxygen is not completely reduced to hydroxide at the gold surface, and that equation (2) better represents the gold leaching reaction (Marsden and House, 1992):• 4Au + 8CN- + 2O2 + H2O ? 4Au(CN)2 - + 2OH- + H2O2 (2)Additionally, since gold leaching is limited by either the diffusion of cyanide or oxygen to the gold surface (Habashi, 1993), then the relative diffusion rates of cyanide and oxygen must also be taken into account. Marsden and House (1992) suggest that the ideal molar cyanide : oxygen ratio is 6:1, while a more recent investigation using laboratory and plant observations (Heath and Rumball, 1998) suggested a molar ratio of 6.9:1.In practice, although a cyanide : oxygen mole ratio of 6.9:1 applies to some circuits, there are many instances when this is not the case.In sulphide ores, galvanic coupling of the gold with the electrically conductive sulphides significantly increases this ratio. Galvanically connected sulphides, and possibly carbon, provide a large surface area for oxygen reduction. As the cathode surface area increases, the oxygen concentration required to sustain the same rate of gold oxidation decreases proportionately.Galvanically connected particles may be composite particles, however they may simply be liberated sulphides in the same suspension as the gold. Particle collisions within a slurry are sufficient to provide momentary galvanic connection (Greet, 1995)."

Jan 1, 2003

By William Skinner, Ishmael Quaicoe, Jonas Addai-Mensah, Ataollah Nosrati

To date, intractable ore specific operational challenges such as poor heap geotechnical stability, permeability and high acid consumption rates associated with low grade (~1 wt%) nickel (Ni) laterites still makes the adoption of heap leaching processing unattractive. This paper presents some highlights of drum agglomeration, column leaching and characterization studies undertaken to foster the understanding and knowledge of some of the desirable product attributes of -2 mm and -15 mm, low grade saprolitic (SAP) and goethitic (G) Ni laterite feed ores and their blends (SAP/G). For column leaching, 5-40 mm agglomerate beds were continuously irrigated with 200 g/dm3 H2SO4 solution at 8.5 dm3/m2/h rate over 100 days. Ni, Co, Fe, Al and Mn extraction rates, free acid concentration, agglomerate bed slump and structural changes were determined as a function of time. The results show that at equivalent feed masses, except -15 mm G which displayed slower, pseudo-layering based behaviour, all the feeds (single and blends) displayed coalescence controlled agglomeration behaviour at varying binder dosages. Whilst the agglomerate compressive strength of the G ore was markedly higher than that of SAP ore, those of the blends were substantially similar. At fixed column leaching conditions, the Ni/Co extractions and acid consumption were higher for SAP ore whilst the agglomerate bed slump was lower than those for G ore. The bed of agglomerates produced from -2 mm G/-15 mm SAP blend was more stable than that for the -2 mm G/-2 mm SAP blend agglomerate, the latter experiencing blockage within 24 h of acid irrigation due to agglomerates breakdown. The Ni/Co extractions and acid consumption rates obtained for agglomerates of -15 mm G/-2 mm SAP blend were lower than expected based on the ratios of the SAP and G ores within the blend composition. The findings suggest that judicious saprolitic and limonitic ores’ blending could reduce acid consumption rate, improve the agglomerate bed robustness and enhance bed percolation behaviour under prolonged acid irrigation periods during heap leaching of lateritic ores of variable mineralogy.

Jan 1, 2014

By Avinash Tripathi

It is now well known that the size distribution of the particulate solid has a significant effect on the breakage behavior of particles in the wet as well as dry modes of ball milling operation. In the context of the size discretized batch grinding kinetic model, grinding behavior of particles is characterized by the breakage rate parameters, k, and breakage distribution parameters, B. Understanding the nature of variation of these two sets of parameters with particle size distribution is important for simulation and control of operation of production mills. However, so far it has not been possible to track the variation of both the set of parameters with grinding time simultaneously. In this paper an attempt has been made in this direction by using a modified functional form approach with time dependent constants. Keywords: dry and wet ball milling, breakage rate and distribution parameters, effect of particle size distribution

Sep 1, 2012

By T. Gong

Often plans to increase plant throughput provide an opportunity for optimising plant equipment and operating methods. This was the case in 2005 at TISCO Jianshan Iron Mine, when an increase in production was planned. The thickening circuit had presented a limitation to the plant throughput and operation with poor overflow clarity and underflow density. Following a course of test work by Outotec, a 53m diameter Supaflo® High Rate Thickener (HRT) was selected for the duty. From early stages of operation of the new thickener, the benefits have been dramatic, including: ? Improved tailings underflow density by 9% ? Improved Overflow clarity to less than 150ppm ? Considerably decreased the water and energy consumption as well as operation cost ? Stable and reliable operation This paper looks at this installation as a case study and compares the previous thickener installa-tion performance with the performance of the single 53m HRT.

Jan 1, 2014

By Dominic Howarth, Diana Drinkwater, Don McKee

"The pressures on mining and minerals education at the tertiary level are well known. Within Australia, for example, the number of undergraduate mining engineering courses with 30 or more students in each year has reduced to three (University of Queensland, University of New South Wales and Curtin University). Similar declines in both student numbers and participating institutions are evident in many other parts of the world, and notably in USA and most countries in Europe.An in depth study of the Australian sector was conducted in 1997/1998, resulting in the Back from the Brink report (Carter 1998). The Australian situation was summarised as follows.Australia’s minerals education system, in its current form, is fragile and is in no position to seize the opportunity (i.e. world leadership in minerals education) and is more likely to succumb to the threat.Current trends include:- an acute shortage of talented academic staff, as a result of University remuneration packages having become hopelessly uncompetitive with those in the minerals industry;- small student populations and high relative costs, making mineral specific courses vulnerable to closures, when Universities are under extreme cost pressures; this situation will be exacerbated if enrolments drop in response to, say, a cyclical down turn in the industry; and- under-resourcing of minerals departments because of their comparatively small size, making these departments incapable of delivering top class teaching in all aspects of their courses, despite being excellent in some areas.Most of the Australian issues identified above have direct parallels in other countries.The most common response of institutions to the threats is to seek strength, and in some cases survival, through various forms of linkages and networks. A number of these associations, which are frequently defensive in nature, are outlined in the paper."

Jan 1, 2003

By Juan B. Yianatos

"After almost 100 years, since the first commercial application began in Australia, flotation has shown an extraordinary growth and nearly 2 billion tons of ore per year are presently treated by flotation processes. During this time flotation has promoted a wide scope of research activities ranging from fundamental chemistry and hydrodynamic studies to studies of industrial operations. In general, fundamental studies have been mainly related to ideal situations. In recent years, however, large efforts have been focusing on achieving a better insight into the actual sub-processes provided by the development of new and more sophisticated instrumentation. Since the massive incorporation of flotation columns, around 15 years ago, a renewed interest in flotation fundamental studies, process modelling and new cell designs have been observed worldwide. The key role of the froth has been recognized as an independent and sometimes rate limiting process step. Thus, separation of pulp and froth process stages seems the most appropriate in terms of process modelling, diagnostic, design and scale-up purposes.In relation to flotation equipment development, until the middle of the 1970’s, only the sub-aeration mechanical cells were dominant. Since the 1980’s, the use of pneumatic cells and forced air mechanical cells has emerged strongly. Also, in the last decade, flotation equipment has shown a dramatic increase in size, reaching values of 200m3 in unitary mechanical cells and more than 300m3 in columns. The general feeling, however, is that, despite the great advance observed in terms of process knowledge, the mechanisms and principles of industrial flotation cells design and scale-up are still not fully understood.Advances in process instrumentation and control now in use allow for more efficient operations, both in metallurgical performance and savings in operating costs."

Jan 1, 2003