Search Documents

By A. N. Zagorodnyaya, T. N. Bukurov, Z. S. Abisheva, A. S. Sharipova

"The paper describes the results of stripping of copper production dusts by leaching with aqueous soda, nitric acid solutions and recovery from solutions resulting in the production of lead sulphate, tribasic lead sulfate (TBLS), ammonium perrhenate, zinc, copper-cadmium cake.The combination of two stripping operations under chosen optimal conditions allows the recovery of 98% rhenium, 82% lead, 92 % copper, and 96% zinc and cadmium each. The major amount of rhenium (~ 80%) is recovered at the carbonization stage, and other metals - at the nitric acid leaching stage.Lead sulfate was precipitated by mixing solutions resulting from carbonization and leaching. Tribasic lead sulfate was produced by dissolving lead sulfate in sodium hydroxide solutions. Rhenium was recovered from mother liquor resulting from lead sulfate precipitation by liquid-liquid extraction and zinc was recovered from raffinates. Trialkylamine (TAA) was used as an extractant for rhenium recovery and di-2- ethylhexylphosphoric acid was used for zinc recovery. Optimal liquid-liquid extraction parameters have been defined allowing the recovery of 96% rhenium in crude ammonium perrhenate and 94% zinc in sulfuric acid solution. Based on the experimental data, the flowchart for dust processing to produce salable products - lead, rhenium, zinc salts has been suggested."

Jan 1, 2003

By Luo Chuansheng, Rao Jinshan, He Xiaojuan, Qiu Xianyang

The dissemination grain size of chalcopyrite is really fine and refractory grains of -10µm take up 25%. Dissemination relationships among chalcopyrite with pyrrhotite, pyrite, marcasite and gangue minerals are complex. Content of Fe-bearing sulphides and Fe-bearing silicates associated with chalcopyrite reaches to about 60%. It’s hard to liberate and separate chalcopyrite from pyrrhotite. The above four are the main mineral processing difficulties of a copper ore in China. Because of the similar floatability and poor separation effect between chalcopyrite and pyrrhotite, enhanced depressing and collecting method was adopted in Cu-S separation before 2009. Due to the different magnetism among chalcopyrite, pyrrhotite and Fe-bearing silicates, magnetic separation is creatively induced in Cu floatation circuit based on the in-depth study of process mineralogy. High efficiency and new Cu-S separation technology of "Rough concentrate regrinding-pyrrhotite rejecting from middling by magnetic separation" and a highly selective copper minerals collector YL-1 had been developed to solve the difficult problems of refractory Cu-S separation, which are heavy load of middling recirculation,difficulty in upgrading Cu concentrate, unstable locked cycle and low separation indexes. And grade of Cu concentrate has been increased by 3.33%, recovery of Cu and Ag has been increased by 19.32% and 10% respectively.

Jan 1, 2014

By A. Singh, M. Ntlhane, V. Ross, M. Dlame

"Fine valuable particles are often lost to flotation tailings streams due to inefficient collection by air bubbles as well as passivation of surfaces by oxidation and slimes. The application of high-shear hydrodynamic cavitation devices (HCDs) to overcome this problem has already proven to be a considerable success in the industry. This paper details the results of further investigations that were undertaken at Mintek to better understand the mechanisms involved when preconditioning feed slurries in an HCD. By promoting inter-particle attrition and conditions of high shear within the reactor, cleaning of particle surfaces is enhanced as well as the formation of superfine (nano) bubbles which are believed to aid their agglomeration and subsequent collection by normal sized bubbles. In order to broaden the envelope of understanding with regard to application of the technology, rather than tailings material as investigated earlier, a Platinum Group Mineral (PGM) UG2 ore from the Bushveld Complex in South Africa was used in this study. The results of a series of batch flotation tests in a 10L Denver cell are presented, being conducted after the feed has been subjected to different methods of preconditioning. It was demonstrated that the preconditioning significantly improved the flotation kinetics of the PGMs, the optimum being obtained after around 20 passes through the reactor. This was accompanied by a much enhanced recovery-mass pull relationship and a significant improvement in the grade-recovery response. Significantly, the selectivity between the PGM and the deleterious chromite (expressed as Cr2O3) gangue more than doubled under these conditions. Modelling of the PGM data by means of the modified Kelsall model indicated that both the fast and slow floating rate constants were improved.INTRODUCTIONIt is well known that the flotation recovery of fine and ultrafine particles, typically less than 10 micron in size, is a challenge (Yoon et al., 1989; Miettenin et al., 2010). Although these particles are typically well liberated, due to their very low mass and inertia, the collision efficiency with air bubbles is low as a result of the inability of particles to penetrate the liquid streamlines around bubbles. Hence the probability of contact is often regarded as the ratedetermining step in flotation of ultrafine particles. Introducing more power into conventional flotation machines is likely to solve only part of the problem, as conventional mechanisms are effective only to a point in terms of shear and micro-turbulence. Further challenges are posed by the treatment of low-grade or oxidised tailings dump material, where valuables are passivated due to prolonged exposure to the atmosphere or slimes. Over the years, various mitigating strategies have been investigated, including the use of dissolved air flotation (Martinez-Gomez et al., 2013; Calgaroto et al., 2015), shear flocculation (Subrahmanyam and Forssberg, 1990), seed or carrier flotation (Tabosa and Rubio, 2010), sonication to clean particle surfaces (Aldrich and Feng, 1999; Newell et al., 2006), high intensity conditioning (Bulatovic and Salter, 1989; Chen et al., 1999; Tabosa and Rubio, 2010), and various electrochemical approaches such as changing Eh in order to promote formation of dixanthogen, dissolution of oxidation products by lowering the pH, activation by sulphidisation (Newell et al., 2006; Becker et al., 2014), and the use of alternative collectors."

Jan 1, 2018

By Ivan Bonchev, Elisaveta Djurova, Evgeni Visariev, Viktor Stoilov

"Two types of slag cooling is used world wide - cooling in ladles and cooling in pits. The flotation comparison of the type cooling regimes was done at Aurubis Bulgaria. In Copper smelter Aurubis Bulgaria (Pirdop), the residual copper in the slags from Flash furnace and Converters is recovered by flotation. The slag flotation plant processes blend of three parts FSF and one part converter slag. The slag processing comprises: pit cooling, crushing, two stages grinding (autogenous and ball) and flotation. The copper content in flotation concentrate is over 20 % and in flotation tail is under 0.5 %. In order to improve the copper recovery, different cooling rate of the liquid slags should be achieved. Three cooling experiments with flash smelting furnace (FSF) slag have been done: two of them in pits with different volume and one cooling experiment in metallic ladle. The ambient air temperature during the cooling tests was from -4 to +4 OC. Laboratory flotation tests in open cycle were done with an aim to compare the slags behaviors cooled at different conditions. In this paper the effect of different cooling on the flotation process will be presented. The copper recovery and distribution by sizes in the tails, copper content in the rougher concentrate, and the concentrate yield are discussed."

Jan 1, 2014

By Cuim R., M. L. Li

Fankou Lead-Zinc Mine produced pyrite concentrate (P.C.) from the zinc tailings by rougher and scavenger flotation before 2010, with the averaged S grade of 40.54% at recovery of 79.34% ( to the feed of S circuit). On the one hand, the economic value of P.C. increases with its purity, on the other hand, when the S grade of P.C. feed to sulfuric acid manufacturer is over 47%, the pyrite cinder can reach a high Fe grade of 62% which can be directly sold as iron concentrate. On this background, engineers in Fankou Mine set the P.C. with S grade of 47% as target. The direct way to reach that goal was to clean the rougher P.C.. Lots of cleaning flotation tests were conducted and the compromised strategy was to produce two ranks P.C. with the S grade of 47% and 38% at the recovery of 44.20% and 36.17%, respectively. The dual-product flowsheet was successfully industrialized in 2010. In order to further improve the quality of P.C., gravity separation was introduced into the flowsheet. The numerical simulation and separation tests were performed to evaluate the beneficiation and classification performance of hydrocyclone as it treated the rougher P.C.. It was shown that the underflow of hydrocyclone could addressed the S grade of 47%, and the finer size overflow could also be enriched to P.C. with S grade of 47% by flotation, due to the contained pyrite with well liberation. That is to say, with the ingenious addition of hydrocyclone to treat the rough P.C., single P.C. with S grade of 47% could be achieved. The new flotation-gravity separation flowsheet was commissioned to produce the high quality P.C. at the end of 2013. The averaged S grade is 47.20% at recovery of 82.26% in 2014. The two steps flowsheet improvement maximizes the enterprise benefits and leads to simple utilization of Fe in pyrite in downstream industry.

Jan 1, 2018

By T. N. Matveeva, T. A. Ivanova

"The article presents the results of the research aimed at development and testing of new effective reagents – collectors and green modifiers for more complete extraction of gold and platinum to concentrates at reduced loss with waste products. The main deposits of Au and PGM ores of Russia and abroad are presented by refractory raw material with the non-uniform finely-interspersed sulfide mineralization, submicron gold and platinum, the low metal content, non-uniform distribution of valuable minerals. and show low indicators of recovery. The main losses of precious metals (up to 15 %) at flotation are associated with thin slam tailings because of inefficiency of standard reagent modes.In the paper, the new trends in design of collecting agents for extraction of gold and PGM sulfide minerals and their application in flotation tests are substantiated. The original technique for obtaining the modified collector reagents – dithiocarbamate, dithiophoshpinate and dithiazine, incorporated non-ionic compounds that are able to generate stable complexes with gold and platinum has been developed. A novel class of collectors – cloud point polymers showed high flotation recovery of fine particles of gold and platinum. The original technique to create the mineral samples of natural sulfides with ""invisible"" or sub-micron gold on their surface designed helped to indicate the mechanism of selective adsorption of novel agents on Au and Pt-sulfide minerals. Extractive UV spectrophotometry, potential measurements, X-ray phase and spectral analysis, scanning electronic microscopy (SEAM), laser SIM and AFM microscopy were applied to analyze the adsorbed layer of modified reagents on the mineral surface. Selective hydrophobic covering on the surface of micro- and nanoparticles of noble metals provided an increase in their extraction during flotation. New reagent modes of modified collectors and green modifiers were tested in scaled-up laboratory flotation and the results obtained demonstrated the increased quality of the concentrates in terms of gold content by 1.5 times and higher gold recovery by 1.5-5%. The studies have been supported by Grants of the President of RF “Scientific School of Academician Chanturiya” NSh-220.2012.5; NSh-748.2014.5."

Jan 1, 2018

By E. V. Zelinskaya, V. U. Starostina

"The Irkutsk region is a raw material region. There are a lot of big enterprises for extraction and processing of oil, gas, coal, iron, gold and rock salt. Besides of it, refractory clays, limestone, mica, gypsum and talc are mined in the region. The most important type of mineral raw material is a gold. More than 8.5% of the total mining in the Russian Federation is extracted in Irkutsk region. It is about 0.7% of the world production. The environmental problems of mining and processing enterprises are a complex set of issues that requires of the searching of effective methods to be solved. One of the key environmental problems remains the reduction of waste generation and the introduction of environmentally safe waste management. After analysing different methods of environmental impact assessment it is established that the method of Life Cycle Assessment is one of the most effective methods for mining production. This method base? on the material balance of flows of raw materials, products and waste. The method of Life Cycle Assessment allows to identify the effects of environmental pollution under the influence of mining and processing at a quantitative level and to show real quantitative forecasts of the possibility of managing the flows of raw materials and waste.INTRODUCTION The Irkutsk region is a raw material region. There are a lot of big enterprises for extraction and processing of oil, gas, coal, iron, gold and rock salt. Besides of it, refractory clays, limestone, mica, gypsum and talc are mined in the region. The most important type of mineral raw material is a gold. More than 8.5% of the total mining in the Russian Federation is extracted in Irkutsk region. It is about 0.7% of the world production. The main provider of precious metal is the Bodaibo region. This is a main location for the major ore companies such as “Vysochaishy”, which produces about 5.0 tons a gold per year; “Pervenets”(PJSC Polyus, the largest gold producer in Russia) - 4.5 tons/year, “Druza” - 0, 5 tons/year. Placer gold is extracted by more than 40 enterprises. In connection with this, there are many plans about a building of new and reconstruction of concentrating factories. Consequently, an increase in the volume of processing is expected. The main projects are the construction of a new mill of the Mining and processing plant GOK “Vysochaishy” with a capacity of 2.6 million tonnes of ore per year; the development of the “Uhakhan” gold-field - 23 km from the “Goltsa Vysochaishy” gold-field; the opening in the Bodaibo region the next parts of the gold-deposit ""Pervenets"". Additional, the growth in a gold production can be achieved by a store of gold in the “Sukhoi Log” deposi"

Jan 1, 2018

By Arkady Senchenko, Yury Kulikov

"Basic theoretical grounds of the methods applied for crushing and grinding parameters determination according to international standards are given in this paper. Statistical data about crushability and grindability research are shown. The potential relationship between the values of Fred Bond Work indices and John Starkey indices (Crushing index, Ball mill index, Rod mill index and AG/SAG index) are discussed in this paper. In order to establish correlation between the crushability and grindability indices the analysis of over 2 500 tests for 165 deposits located in different parts of the world was performed. The relationships among different types of energy consumed for crushing and grinding were determined. A method for preliminary estimation of energy consumption in semiautogenous + ball mill grinding circuit is suggested for its application in preliminary technological solutions development and technical-and-economic assessment."

Jan 1, 2014

By Y. Y. Li, Q. Chen, Y. X. Cai, Q. Zhang, S. Mao

"Due to the influence of combustion conditions, the fly ash produced by some power plants has the problem of high-carbon content. The unburned carbon in fly ash can be removed by flotation, and the decarbon tailings should reach the national standard level I fly ash. The fineness of the requirement is one of the important indicators and is also an important factor affecting the tail ash activity. In this paper,adopting two methods investigate the effect of particle size on the flotation index: one is direct flotation of fly ash, and the other way is wet grinding + flotation of fly ash, comparing the two methods and selecting the appropriate process,which provides a way for the effective utilization of fly ash. INTRODUCTION Fly ash is a solid waste discharged from coal-fired power plants. The annual amount of emissions of fly ash are very large in China. The amount of fly ash were discharged from coal-fired power plants are increasing gradually, and the amount of fly ash stored has exceeded 2.5 billion tons, but the comprehensive utilization of fly ash is not high, which brings about a huge environmental problems( Lu et al.,2011). Carbon is a harmful component of fly ash in cement and concrete application (Zhang et al.,2008). Fly ash decarburization is an essential link to improve the utilization efficiency of fly ash and the reduce pollution ( Yang et al.,2012). Carbon is selected from fly ash to make full use of fly ash resources and improve utilization of fly ash (Li et al.,2008). In this paper, the flotation decarburization of high-carbon fly ash is studied, through comparing the grinding and not-grinding processes, optimizing the separation process of fly ash, which provides a way for the effective utilization of fly ash."

Jan 1, 2018

By A. Kuriwada

Dolomite is a mineral, which consists of CaCO3 and MgCO3. In this work, a series of experiments were carried out in order to adsorb boron from a boron-containing solution using a calcinated dolomite sample, and then to desorb it from the loaded adsorbent. A particular modification on the surface of dolomite was observed when it was thermally treated at certain temperature, ranging from 750 oC to 1050 oC; in turn, it is the specific surface was increased. In other words, the experimental results suggested that the calcinated dolomite exhibited a high adsorption capacity for boron, indicating its effectiveness in effectively adsorbing boron from drinking water or wastewater.

Sep 1, 2012

By Shuji Owada, Mayumi Ito, Idemitsu Kosan Co. Ltd., Takehiko Nishimu, Sadayuki Shinozaki, Takashi Ando, Tomoe Ota

"fElectrical disintegration (ED) by high voltage electrical pulse is a relatively new technique which was demonstrated by Tomsk and Mekhanobr in the 1960’s and has been investigated in detail by Andres in the 1990’s. In the ED, the electrodes should contact to the targeted material and the energy of high voltage pulse is charged directly to the material. It has been reported that the ED is quite efficient to improve liberation of composite materials, because electrical current passes often through the conductive part and/or along the phase boundaries. Theoretically, the energy required in the ED should be lower than in the other mechanical breakage methods, because breakage occurs basically by tensile strength in the ED while in the other mechanical methods it does mainly by compressive strength which is generally ten times or higher than tensile strength.Coal, involving many kinds of mineral matters, is considered to be one of the targets for the ED to apply to. In Japan, national “Hyper-Coal Project” is now running, in which ultra-clean coal (less than 200ppm of ash, 0.5ppm of Na and K, and 2ppm of Ca) is planned to produce by combining advanced coal preparation and liquefaction technologies for the purpose of direct injection of coal combustion gas to turbine. The ED is one of the major techniques to be developed in this project, since mineral matters must be liberated before introducing to the following advanced separation processes. Liberation is important also for the utilization of middling coals generated from usual coal preparation plants. The application of the ED to the middling coals is considered effective for upgrading these coals with higher liberation degree and less energy input."

Jan 1, 2003

By C. Dorfling, P. Albertyn

"Hydrometallurgical recovery of metals from printed circuit board waste typically involves multiple leaching stages; conventionally, base metals dissolution by mineral acids is followed by leaching of gold using cyanide or halide based lixiviants. Alternative lixiviants for gold leaching can reduce the potential hazardous nature of operation. The aim of this study was to investigate the feasibility of using thiosulfate as lixiviant for gold leaching from waste printed circuit boards. Batch leaching tests were performed to investigate the effects of thiosulfate concentration (0.1 – 0.2 M), ammonium concentration (0.2 – 0.4 M), pH (9 – 10.5), solids content (25 – 50 g/L), and copper content of the feed material on the gold leaching behavior. The concentrations of metals in liquid samples were determined by means of inductively coupled plasma atomic emission spectroscopy, and high pressure liquid chromatography was used to evaluate thiosulfate degradation/consumption. The ratio of thiosulfate to ammonia was found to have the most significant effect on the extent of gold leaching, with the best gold extraction observed at a ratio of 0.5 mole thiosulfate per mole ammonia. The lower pH range of 9 – 9.5 generally produced better Au leaching, while low copper extraction during the first stage base metal leaching stages has proven to be detrimental to gold leaching from the residue. Thiosulfate degradation/consumption increased and gold extraction decreased with higher residual copper in the feed. An optimum gold extraction of 78.5 % from base metal leach residue was achieved with 0.2 M thiosulfate, 0.4 M ammonia, and 0.02 M cupric ions at 25°C in the pH range 9 – 9.5.INTRODUCTION Background and Aim The recycling of e-waste is becoming increasingly important as it provides certain economic benefits apart from the obvious environmental benefits. Printed circuit boards (PCBs) are found in most forms of e-waste and contain especially high concentrations of base and precious metals. Hydrometallurgical processes are often considered for the recovery of valuable metals from PCBs; these processes normally implement several leaching stages to selectively recover certain metals."

Jan 1, 2018

By X. P. Guo

In this paper the test results of flotation of the kyanite ore from a Chinese mine are described. The objective of this work is to determine effective recovery process to obtain kyanite concentrate with high quality and high recovery for a new concentrator design. The valuable minerals of the ore are kyanite, garnet and magnetite, contents of them are 14.0%, 5.9% and 1.2%, respectively. The gangue minerals are mainly biotite, feldspar and quartz, contents of them are 33.8%, 17.8% and 25.6%, respectively. The kyanite in the ore contains a little iron. In laboratory flotation tests the factors affecting the flotation such as slime, alkalinity of pulp, and flowsheet configuration are studied. The interference of biotite on kyanite flotation as well as selective flotation of garnet is examined. On the basis of above-mentioned results the flowsheet of ore treatment comprising de-sliming, mica flotation, low intensity magnetic separation of magnetite, high intensity magnetic separation of garnet and coarse biotite as well as flotation of kyanite is pre-sented for comprehensive recovery of kyanite, garnet and magnetite. The kyanite concentrate con-taining more than 59% Al2O3 is obtained with a kyanite recovery of 70.0%. The contents of Fe2O3and biotite in kyanite concentrate decreased from 2.02% and 5% to 1.30% and 1%, respectively. The disadvantage of low kyanite grade in raw ore is compensated by accessory recovery of garnet and magnetite in the ore.

Jan 1, 2014

By J. Seo, W. Kim, I. Bae

"Microcrystalline silica impurities such as quartz and opal-CT commonly associated in bentonite should be controlled and removed as far as possible when bentonite is used as biocompatible raw material because they show sufficient evidence of carcinogenicity. Since opal-CT contained in bentonite in trace amounts cannot be well separated by conventional sedimentation method, in this work, the ultrasound-assisted removal of the impurity was attempted. Irradiating ultrasound into bentonite-water suspension promoted the production of fine montmorillonite particles in the suspension and the production markedly increased when montmorillonite was activated by Na2CO3. Subsequent centrifugation of the suspension made it possible to recover pure montmorillonite particles as an overflow product. Only 16.2 mass % of total solids was recovered as an overflow from the non-activated suspension, whereas 63.5 mass % was recovered from the activated suspension at centrifuging speed of 10000 rpm. Increasing sonicating time enhanced the yield of overflow, however, excessive sonication up to 10 min hindered the purification of montmorillonite. It was observed that the peak reflection of (101) plane of opal-CT in overflow increased as sonicating time increased during prolonged sonication. INTRODUCTION Bentonite consisting predominantly of mineral montmorillonite is clay-rich soft rock generated frequently from the alteration of volcanic ash. Depending on the nature of its genesis, bentonite contains a variety of accessory minerals, which may include mainly quartz, feldspar, opal cristobalite/tridymite (opal-CT), calcite, illite and mica. The presence of these accessory minerals can impact the industrial value of the deposit, reducing its commercial value depending on its applications. Therefore, bentonite is often purified by removing these impurity minerals for special applications where specific properties and characteristics are required (Murray, 1999). Among the special applications, bentonite is often used in the cosmetic and pharmaceutical industry as both excipient and active ingredient in the forms of liquid (suspensions, emulsions), semi-solid (creams, ointments) and solid (powder, capsules and tablets). The basic requirements for bentonite to be used as raw material are pure, microbiological and mineralogical inertness. Physical properties such as swelling volume and gel formation are also important. Particularly, microcrystalline silica polymorphs such as quartz, cristobalite and opal-CT should be controlled and removed as far as possible because they show sufficient evidence of carcinogenicity in humans."

Jan 1, 2018

By V. Sovmen

The gold-ore Olympiada deposit is located within the Yenissei range (Krasnoyarsk Region, Russia). Primary sulphides ores are metasomatic changed rocks, mica-calcite-quartz structure with impurity amphiboles, chlorites, carbon, the rare thin grains of sulfides (up to 3%~5%) and native gold. The structures of ores are fine-grained, prevailing texture of ores - interspersed, vein-interspersed, band-interspersed, veinlet. The most important minerals in the deposit are: gold, arsenopyrite, pyrrhotite, antimonite, Sb-sulphosalt, quartz, muscovite, calcite, siderite, titanium minerals, chlorite and minor sulfides like chalcopyrite, galena, sphalerite, etc. A common problem in mineralogical studies applied to mineral processing (concentration, cyanidation, etc.) is the characterization of gold in ores and technological products. This paper discusses the behavior of minerals during technological process at operating factory in Olympiada Mine and gold distribution in the ores and products. For the mineralogical characterization of minerals ? combination of analytical techniques was used. Gold is encountered in the primary ores as free grains among rocks, growth with sulfides and nonmetallic minerals, inclusions in sulfides, sulphosalt, and nonmetallic minerals. The gold-sulphide ores of Olympiada deposit can be quite complicated for enrichment. With the purpose to increase the extraction of metal from concentrates by liberating the dispersed gold, forming inclusions in sul-fides, there is used technology of biooxidation of flotation concentrates in Olympiada Mine. Gold and the basic ore-forming minerals in the ores feed, sulphidic concentrates, biocakes, tailings of concentrates of flotation and products of hydrometallurgical leaching have been studied in the mineralogical research. During researches it is established that pyrrhotite was completely oxidized while arsenopyrite was oxidized almost completely in the bacterial oxidation process. Pyrite and antimony minerals behave similarly and were oxidized only partially. The main oxyhydroxides in the bacterial oxida-tion process are goethite, limonite and jarosite. The results of mineralogical researches showed reasons of losses of gold during hydrometallurgical enrichment.

Jan 1, 2014

By D. Moradkhani

Copper metal has important role in the basic industrials, as if it did not exist, modern human life would not develop! Copper leaching, as the first step, is important step in copper production processes. In this research, efficient factors on the leaching have been investigated. For this reason, four efficient factors on leaching namely pH, liquid to solid ratio (L/S), temperature and time, as independent variables, were optimized using response surface (RSM) with D-optimal. A quadratic equation was used to create response and contours. According to the results from analysis of variance (ANOVA), the value of determination coefficient (R2=96.77%) indicates that the model was good fit. Optimum experiment condition also was found: pH of 1, L/S of 8.24, temperature of 26.06 ? and time of 43.64 min. At this condition, the maximum recovery of copper was equaled to 92/38 in which good desirability achieved.

Sep 1, 2012

By Mingfei He, Yude Gao

"The leaching kinetics was studied during leaching of indium-bearing zinc oxide to recover indium. The effects of temperature, sulfuric acidity, particle size, stirring rate on dissolution rate of indium were investigated. Results showed that the leaching process was controlled by chemical reaction at the condition of low sulfuric acid concentration. While the acidity increased to 1.8 mol/L, the leaching process was transformed into an internal diffusion controlling model . The corresponding value of reaction orders under low acidity and high acidity were 1.194, 0.156, respectively. Further calculation results indicated that the leaching reaction activation energy was only 10.97kJ/mol under the condition of high acid. The leaching rate constant was inversely proportional to the square of particle size, while the effect of stirring rate on leaching process was insignificant. The leaching process can be enhanced by increasing the temperature and acid concentration, as well as the decrease of particle size. And a final kinetics eqution was proposed. KEYWORDS Indium, extration, leaching kinetics, zinc oxide INTRODUCTION Indium[1,2] plays an important role in many aspects of living and industrial production owning to its special physical and chemical properties. The reserve of indium is rare on the earth, and most of indium is distributed in some other minerals[3]. Some researchers [4,5] have proposed that indium mainly substitutes for the lattice of other minerals by isomorphous. Therefore, the extraction of indium should take into account of the production technologies of those minerals to comprehensively recover the valuable metals."

Jan 1, 2018

By L. Pan

As an air bubble approaches a mineral surface, a thin liquid film (TLF) is formed in between. The excess pressure (p) in the film determines the kinetics of drainage, which is of critical importance in flotation. We have developed a new method of monitoring the kinetics for both stable and unstable wetting films and analyzed the results using the Reynolds lubrication theory. It has been found that initially a TLF is thinned by the Laplace pressure (pcur) due to changes in bubble curvature and subsequently by the disjoining pressure (?) created by the surface forces present in a wetting film. In the present work, we have derived an analytical expression for determining ? from the temporal and spatial profiles of TLFs on mineral surfaces. The results show that ? > 0 in a film formed on a hydrophilic surface and ? < 0 in a film formed on a surface hydrophobized by collector. Thus, the role of collector in flotation is to create a hydrophobic force and hence a negative disjoining present in wetting films. It is also found that smaller bubbles can create higher Laplace pressure, which helps the TLF drain faster.

Sep 1, 2012

By Sunil K. Tripathy

Particle characteristics such as size, density, liberation and magnetic susceptibility play vital role in magnetic separation technique. To understand the performance of magnetic separation process for chromite beneficiation industry, particle characteristics need to be analysed. However, to date, this has been an expensive and time consuming task, thus only minimal amounts of this type of data are available in the literature. Several new methods are being developed, that will produce the required mineralogical and liberation data to provide processing information rapidly and inexpensively. Among these, QEMSCAN is a unique and advanced characterisation equipment used for liberation analysis for different ore whereas S.G. Franz Isodynamic Separator for determining the magnetic susceptibility. In Indian chromite deposits, the content of iron bearing minerals in the ore is typical which controls the Cr:Fe ratio in the product while treating in gravity based beneficiation plant. In the present investigation, detailed characterisation of two distinct chromite ore samples from Sukinda chromite deposit, India, was investigated which includes advanced mineral characterisation using QEMSCANand magnetic susceptibility measurement by using Frantz Isodynamic separator, etc.. Presence of haematite and gibbsite along with chromite mineral were identified as major gangue minerals in the high grade ore from XRD pattern whereas Goethite, Quartz, Haematite, Kaolinite, Ringwoodite identified in the low grade ore. The mass magnetic susceptibility of low grade ore is very high 5.2 cm3/g compared to 2.7 cm3/g for high grade ore, due to the presence of abundant quantity of iron bearing minerals. Subsequently, these two types of ore were subjected for magnetic separation for improving Cr:Fe ratio by using different magnetic separators viz. induced roll magnetic separator, wet high intensity magnetic separator, rare earth roll magnetic separator, rare earth drum magnetic separator. The results of magnetic separation studies indicated that, Cr: Fe ratio of the chromite ores can be improved to 3.99 and 1.97 from the feed assaying 3.09 and 1.29 respectively. Studies on rare earth roll magnetic separator indicated that both the ores were upgraded to a maximum Cr:Fe ratio level at optimised condition. Keywords: characterization, QEMSCAN, magnetic separation, rare earth roll magnetic separator, industrial mineral, chromite

Sep 1, 2012

By Luis Bergh, Francisco Díaz, Isabel Panire, Juan Yianatos, Luis Vinnett

"In this paper, industrial data of residence time distribution (RTD) in mechanical flotation cells is presented, which were measured in several plants using the radioactive tracer technique. Results include mechanical flotation cells of 100 - 300 m3, which were operated with effective residence times from 2 to 7 min. Tests were developed in forced air and self-aerated cells for liquid and solids (non-floatable) per size classes. Different RTD model structures including perfect mixer, Large and Small Tanks in Series (LSTS) and by-pass flow plus perfect mixer were evaluated and compared for single cells. The actual mixing regime was related to the effective residence times and cell designs based on the model fitting. By-pass flow percentages were typically lower than 10%, therefore the perfect mixer model plus a dead time was a suitable model structure in most cases. On the other hand, the arrangement of cells in series was effective in reducing the bypass flow observed in single cells (by-pass flow percentage greater than 5%). In addition, the N perfectly mixed reactor in series model was used to represent the mixing regime along flotation banks, which were operated with mean residence times in the range of 18 - 53 min. Results showed that N tanks in series plus dead time were closer to the actual values in most cases."

Jan 1, 2014