Search Documents

By Janne Kauppi, Kaj Jansson, Piia Suvio, Saara Hagnäs

"Historically the focus at the mineral processing sites has been to improve the production operations, while little focus has been set on how factors, such as the quality of water used in the process affects the metal recovery. Simultaneously increasing public pressure and water scarcity is driving the mining industry to recycle more water back to the process, which in turn leads to accumulation of impurities within the recycled water. This paper presents a concept for a systematic approach on targeting the impurities that have a negative effect on the metal recovery at the flotation circuit by using a novel solution called Process Water Recycling Plant (PWRP). These plants are designed with specific ore type in mind. PWRP produces cost-effectively process water to different target qualities, especially for flotation purposes enabling higher and more stable flotation recovery. It consists of pre-designed and standard water treatment units for a wide range of volumes. The application-specific configuration of units is governed by the water quality requirements, and can be designed according to specific customer needs. Testing has been carried out in order to investigate, which recycling water impurities affect the different ore types and how the metal recovery in flotation is affected as a consequence of the poor-quality water. The results indicate that every ore type is impacted differently and without a good understanding on how the water quality impacts the process performance, adverse effects on the flotation recovery can occur.INTRODUCTION With a focus on where water is used within the mineral processing, it has become evident that even though water is used in several different processes, majority of the water losses within the site occur at the tailings processing and the tailings storage facility. New tailings management technologies that can increase the recovery of water are actively being developed, but the key to improving the efficiency of water use and reducing the operational risks lies in closing the water loops and increasing the slurry density in the tailings processing. With this shift from conventional tailings technologies towards paste and dry stacking, water efficiency is vastly improved, but it might in turn lead to process water challenges with impurities, reagents and fines being recycled and accumulated within the production processes."

Jan 1, 2018

By Jing Zhou

2-hydroxy-3-naphthoy hydroxamic acid code name F203 is a good collector of cassiterite, 1-hydroxy-2-naphthoy hydroxamic acid code name ZJ-3. F203 and ZJ-3 are similar series of isomers. They have similar naphthye, and similar series of functional OH and ?CONHOH, but the seat of OH and ?CONHOH group are different, on the F203 is 2.3; on the ZJ-3 is 1.2, ortho position too. According to Isomeric principle ZJ-3 is a good collector of cassiterite slime too. Using ZJ-3 as collector flotation -10µm occupies 90%, grade 1.16% Sn cassiterite slime of Da Chang Chehe concentration plant, pass one coursing flotation, two cleaning and one scarenging flotation, and obtains grand 18.26% Sn, recovery 92.68% cassiterite concentrate. The result proves the Isomeric principle of flotation reagents is correct again. This principle may supply to synthetize new flotation reagents reference. Keywords: F2O3, ZJ-3, cassiterite flotation, Isomeric principle, Isomeric principle of flotation reagents

Sep 1, 2012

By C. L. Xiao

With reference to the test report carried out by Guangzhou Nonferrous Metal Research Institute in 1983, the mineral process flow sheet of Yichun Tantalum-niobium mine is determined based on the characters of ores and successful experiences in light of the problems in the existing flowsheet: The ore is desilted before crushing; the primary slime is separately treated; the staged grinding process used while the fine slime is collectedly treated with tantalum and niobium as the main recoveries and lepidolite and feldspar powder as the secondary. The flowsheet is featured by comprehensive recovery, low investment and low energy cost.

Jan 1, 2014

By Liu Jie

Refractory iron ore deposits in China have various genesis and complicated types, the nature of which is poor, fine-disseminated and complex. Therefore, refractory iron ore could scarcely be separated and utilized by traditional mineral processing technology at present. It is necessary to explore deep reduction technology to change the characteristics of refractory iron ore and to use effectively the iron resource. And deep reduction technology is that on the condition of higher reduction temperature than that of magnetic roasting and stronger reducing atmosphere, the iron oxides from iron ore was reduced to metallic iron particle that is easy to dissociate. And then production from deep reduction is easily separated by magnetic separation and iron powder production was obtained finally. Deep reduction technology for Lingyang iron ore from Jilin, China, as the refractory iron ore, was studied in this paper. The influences of such main factors as reduction temperature, time and coal content were investigated. The results showed that the Metallization rate of reduction product was up to more than 90% under optimum conditions, and then higher iron grade and recovery of reduction iron powder were obtained from subsequent magnetic separation. Furthermore, the deep reduction mechanism in the system was studied by the means of XRD and SEM analysis for reduction production and Physical Chemistry of Metallurgy. Analytical results indicated that during deep reduction, the size of iron particle from deep reduction materials was increasing as reduction temperature rising and reduction time extending. The growth of metallic iron particle from deep reduction production was divided into such three stages as reduction nucleation, deep reduction and growth of metallic iron particle.

Sep 1, 2012

By Mohsen Hashemzadehfini

Nowadays heap leaching has become established as a mineral processing technology for treatment of some low grade minerals such as copper, gold, and zinc, etc. Heap height, particle size, leach reagent consumption, and metal recovery are four important metallurgical parameters in a hydrometallurgical process like heap leaching. This paper investigated the effects of heap height and particle size on copper recovery as well as acid consumption. Three heap heights of 2, 4 and 6 meters and two particle size fractions of less than 25.4 mm and 50.8 mm were selected as variables in the experiments. The research results showed the inverse relation between heap height and copper recovery as well as acid consumption. Under given conditions, the copper recoveries of minus 25.4 mm ore are 78.63%, 66.27% and 52.88% higher than that of minus 50.8 mm samples for the heap heights of 2, 4, and 6 m, respectively. Both copper recovery and acid consumption increase with decreasing particle size. Keywords: heap leaching, heap height, particle size, acid consumption

Sep 1, 2012

By E. V. Zelinskaya, A. E. Burdonov

"In the raw aluminum production processon electrolyzers with self-baking anodes, during technological operations, flow-regulated treatment and adjustment of the electrolyte chemical composition produced by diesel and floor-rail technology, alumina and fluoride salts are spilled through the ventilation grilles of the electrolysis body aeration channels, leakage in the equipment, machinery and motorized machinery construction elements. As a result of this, a part of the bus station and the level of ± 0 (the basement room with supporting curbstones and columns, on which electrolyzers are installed) are covered with technological raw material. This leads to an increase in the conductor (bus) resistance, contact connections deterioration, cell insulation failure and raw materials loss. For example, at the enterprise ""Rusal-Bratsk"", as a result of the activity, up to 420 tons per month of alumina-containing wastes that are unfit for use in the electrolysis process are formed due to the alumina substantial contamination with salts of iron and silicon, which significantly reduces the technical and economic parameters of the electrolysis process. The main scientific problem is the processing (cleaning) of alumina-containing waste having a complex mineralogical composition of the material, its contrast and structure, from oxides of iron and silicon, using ""dry"" separation methods. In the performing the work process, qualitative indicators of the influence of external factors (air humidity, precipitation, sunlight, temperature difference) on the physicochemical processes components interaction during the raw materials storage are established. On the basis of laboratory tests, it is established that alumina-containing raw materials can be separated and photometric and gravitational separation methods used. A mathematical model of the motion of particles of primary and prepared alumina-containing raw materials in a cascade-gravity classifier was developed. The criteria and factors characterizing the alumina-containing material, as well as influencing and determining the maximum material enrichment, are established."

Jan 1, 2018

By Jia Ma, Lu-De Qiang, Zhi-Chao Liu, Chun-Feng Li, Guang Li, Bao-Bin Tang

"At present, research on the surface chemical properties of uranium minerals is very scanty, which restricts the research progress of uranium ore flotation process research. The research aimed at exploring the surface characteristics of two common uranium minerals and providing basis for flotation process to enrich uranium minerals in ore. This paper selected pitchblende and uraninite as the object of study, which are widely distributed in uranium deposits. We chose out the pure minerals of pitchblende and uraninite from different ores collected from different uranium deposits. By means of Zeta potential test and X-ray photoelectron spectroscopy (XPS) test, a preliminary study on surface characteristics of the pure minerals of pitchblende and uraninite was conducted. And the significance of the change of Zeta potential, the elements composition and valence state on the minerals surface for flotation was discussed. The research shows that, the Zeta potentials of pitchblende and uraninite in pure water are negative mainly when the pH value varies from 2 to 11, which maybe a result of the difference of ionization capacity between two kinds of oxy-compounds on the surface of minerals. On the surface of pitchblende and uraninite, the metal elements are mainly U, Th and Pb. U is mainly in the form of UO2, Th is mainly in the form of ThO2, and Pb is mainly in the form of Pb and PbO. Based on the surface characteristics of pitchblende and uraninite, we can select process and reagents appropriately in uranium ore flotation.INTRODUCTION Globally, the major challenges associated with exploitation of low grade ores are about finding economically feasible processes for reducing the mass of gangue minerals (Filippov et al., 2012). Among the beneficiation technologies of low grade uranium ores with complex minerals assemblage, flotation is the common process which is used to reduce production cost and eliminate the acid-consuming minerals (Li et al., 2016; Liu et al., 2015)."

Jan 1, 2018

By Antony Amberg, Gonzalo Saldías, Romke Kuyvenhoven, Catherine Souza, Heriban Soto, Francisco Soto

"Vizcachitas is an advanced stage copper–molybdenum porphyry deposit, fully owned by Los Andes Copper and located in Central Chile. The property contains an indicated resource of 1,038 million tonnes grading 0.37% Cu and 0.012% Mo, and an inferred resource of 318 million tonnes grading 0.345% Cu and 0.013% Mo (Coffey & Alquimia, 2014). The deposit occurs in the same geological belt as several other giant copper-molybdenum porphyry deposits including Río Blanco-Los Bronces, Los Pelambres-Pachon and El Teniente. In 2018, the original Preliminary Economic Assessment (PEA) study from 2014 was updated; this paper presents the geometallurgical testwork that was performed to support that update. The testwork focused on the metallurgical characterization of 40 DDH samples and the development of a more profound orebody knowledge by relating geological features with metallurgical performance. The scope of work included complete chemical and mineralogical QemSCAN characterization; SAG, ball mill and abrasion testing; complete rougher and cleaner kinetics including locked-cycle-test; environmental ABA and settling tests on rougher tailings. The results show that the ore can be classified as medium-hard, with a hardness that is slightly below the average for large Cu/Mo deposits in the region. A good correlation was found between lithology and breakage characteristics, implying that the specific energy consumption (kWh/t) is well correlated to rock type. The results of the flotation tests were very encouraging and did not show significant variability. An overall Cu recovery of 91% can be expected for the flotation circuit. The use of a relatively coarse primary grind size gave good final recovery and grade for both Cu and Mo, and deserves further attention in future work, as this impacts positively both energy consumption and water recovery.INTRODUCTION Los Andes Copper Ltd. is a Canadian exploration and development company focused on the acquisition, exploration and development of advanced stage copper deposits in Latin America. The company owns 100% of the Vizcachitas project in Chile, the largest copper deposit in the Americas not controlled by the majors. Vizcachitas is a copper-molybdenum porphyry deposit, located 120 km north of Santiago, in an area of very good infrastructure."

Jan 1, 2018

"The thiosulfate leaching process developed by Barrick to treat sulfidic high preg-robbing gold ores uses calcium thiosulfate as the leaching reagent for ores pre-treated by pressure oxidation, resin for gold recovery with sulfite/trithionate elution and reverse osmosis as a means of reagent recovery. A large portion of the research that led to the development of the technology was based on previous studies completed by different groups over the years, mainly focused on the ammonium thiosulfate system. Operational limitations in the use of the ammonia-containing recycled water in the pressure oxidation circuit were some of the main drivers for the change from ammonium to calcium thiosulfate for the development of the industrial scale process. One of the main aspects for successful gold extraction and recovery in the thiosulfate system is the pseudo-equilibrium reactions that drive distribution of the different gold species (in solids, solution and on resin) in the system. Previous studies have been focused on the thiosulfate reactions and equilibrium constants for the oxysulfur ions (thiosulfate, trithionate, tetrathionate). However, the literature around the effects of the different metal-oxysulfur complexes (Cu and Hg complexes) that form when the ore is in contact with the leaching reagents, and the related effects on stability of the gold complex is limited. The main changes in the gold complex chemistry and stability in the calcium thiosulfate system as compared to the ammonium and sodium equivalents, as well as related effects on gold recoveries, were investigated in the presence of different types of double refractory ores. INTRODUCTION Barrick has developed a thiosulfate leaching process to treat double refractory gold ores, by combining the use of acidic and alkaline autoclave pre-treatment with thiosulfate resin-in-leach (RIL). The process currently in operation at the Goldstrike mine (the TCM process), uses calcium thiosulfate as the leaching reagent, resin for gold recovery with sulfite/trithionate elution and reverse osmosis as a mean of reagent recycle. The main feed to the process plant is highly preg-robbing sulfidic ore from Goldstrike’s open pit. Prior to feeding the pressure oxidation circuit, the ore is processed through the crushing and grinding circuits and treated in preparation for acid or alkaline autoclave processing (POX)."

Jan 1, 2018

By Klaus M. Hahn, Hermann Wotruba, Bernd G. Friedrich

"Due to an increasing demand for nickel and cobalt and the depletion of nickel sulphide deposits worldwide, the production of ferronickel from lateritic nickel ores becomes more significant. About 60 percent of nickel reserves are present in laterite deposits. Common production methods like acid leaching or smelting operations implicate high material and energy consumption. Physical processing methods are also not efficient, because of the fine microstructural intergrowth of the minerals carrying valuable elements such as nickel and cobalt. Due to the high energy consumption of metallurgical treatment of lateritic nickel ore (nickel grade: 0.8 - 3.0%, Co: 0.05 - 0.15%), the separation of waste material (about 75 - 85%) before the metallurgical treatment is desirable. Therefore, an alternative process has been developed, combining a pyro-metallurgical pre-treatment with selected mechanical processing methods. The developed process consisted of a selective pre-reduction and non-selective segregation of the contained metal phases in the first stage. By this, the properties of the metal carrying minerals were changed and could become subject to concentration by means of fine beneficiation processes afterwards. The parameters of the pre-reduction and segregation were varied and the pre-treated samples were examined concerning their efficiency of metalization grade and metal grain size. This paper describes the investigation of pre-treatment methods of a lateritic nickel ore. The pre-treatment and possible subsequent separation methods were examined with regard to the recovery of the valuable elements. Metalization grade was around 80% for both Ni and Co with metal phase grain sizes below 20 µm. Scanning electron microscopy revealed distribution of new metal phases not only on the reducing agent, but also on the “slag” material.INTRODUCTION Nickel laterites are characterized as strongly weathered regoliths with several zones containing reserves of nickel (Ni) and cobalt (Co). These laterites are formed on serpentinites and ultramafic rocks under climatic and/or tectonic conditions that have changed over time (Butt & Cluzel, 2013). The formation of Ni laterites is influenced by numerous geological and environmental factors. In general, there are three ore types named according to the dominant Ni hosting minerals: oxides, hydrous magnesia (Mg) silicates and clay silicates (Butt & Cluzel, 2013). The most Ni laterite deposits contain two of these ore types, usually an oxide zone and an either clay or Mg silicate zone. Distribution of these principal deposit types, their average Ni-bearing phases and mean Ni grade are shown in Table 1. A schematic profile of the different deposits based on the development on serpentized ultramafic rocks is given in Figure 1 (Butt & Cluzel, 2013)."

Jan 1, 2018

By Zoran S. Markovic

The extensive laboratory investigations were carried out in order to determinate behavior of sulphide and nonsulphide copper bearing particles during the flotation. The present ore sample were contained 0.55% Cu with 20.1% of nonsulphide copper in it and gangue material with higher contents of alumina about 19.07%. In this paper will be presented some results such as: effect of particle size, pH and applied collectors. The main goal was in application of collectors S-7518, as well as mixture of KEX and Z-96. Z-96 is a product from Chemical Industry Zupa Krusevac which was used as auxiliary collector in mixture with xanthates. The best results were done with this mixture in ratio KEX / Z-96 as 77/23 % in area of oxidized minerals flotation, but the collector S-7518 was achieved better results in sulphide mineral flotation. The S-7518 has better selectivity between copper minerals and pyrite comparing to mixture of KEX/Z-96 in mentioned optimal ratio. Flotation recovery and copper grade in concentrate were studied by flotation kinetics tests.

Sep 1, 2012

By Z. T. Yuan, S. L. Qi, Q. Y. Meng, G. X. Zou, L. X. Li, J. W. Lu

"The selective separation of pentlandite from serpentine was investigated using the magnetic coating-magnetic separation by conditioning slurry pH value, stirring speed, magnetic field intensity and controlling dosages of sodium hexametaphosphate (SHMP) and sodium oleate (SO). The optimal conditions were obtained as follows: the natural pH of 6.8-7.2, stirring speed of 2300 rpm, magnetic field intensity of 200 kA m-1, SHMP of 60 mg L-1, and SO of 400 mg L-1. Results showed that the Ni grade was 21.4% with the Ni recovery of 81.4% and MgO content of 3.8%. FTIR indicated that coagulant of SO preferentially adsorbed onto pentlandite and magnetite particles while hardly adsorbing onto serpentine particles when dispersant of SHMP was used. Thus, the selective magnetic coating of magnetite on pentlandite surfaces could be formed due to the formation of hydrophobic surfaces on pentlandite and magnetite particles. Calculations of DLVO (Derjaguin-Landau-Verwey-Overbeek) confirmed that interactions between magnetite and pentlandite particles were much stronger than that between magnetite and serpentine due to the existence of hydrophobic interactions with the addition of SO. Consequently, the pentlandite was successfully separated from serpentine. Therefore, this study exhibits the potential to separate pentlandite from serpentine minerals for practical applications and thus deserves further study.INTRODUCTION It has been well known that the separation of pentlandite from serpentine is a worldwide challenging issue in the processing of sulphide nickel-copper ores. Because the serpentine mainly causes the high pulp viscosity and slime coating on the pentlandite, which interferes with the flotation process of pentlandite (Cao et al., 2016; Feng et al., 2012). The fibrous mineral of serpentine preferentially attaches to the air bubble, forming bubble-macrofibers aggregates, which are easily floated into the nickel concentrates, resulting in the decline of Ni grade (Alvarez-Silva et al., 2016; Kusuma et al., 2014). In addition, the serpentine adheres to the pentlandite as hetero-aggregation or slime coating via the electrical interaction between a positively charged serpentine and a negatively charged pentlandite, which decreases the hydrophobicity of pentlandite and reduces the collector adsorption (Feng et al., 2013). In other words, the presence of serpentine or the occurrence of aggregates (including slime coating and bubble-macrofibers aggregates) seriously affects the flotation process and deteriorates the flotation of pentlandite. Therefore, we propose magnetic separation to recover pentlandite from serpentine with the magnetic coating technology, which is different from forth flotation."

Jan 1, 2018

By J. Kwon, D. Lee, H. Cho

"The use of the combined grinding and liberation model to predict liberation characteristics of iron ore comminuted by a ball mill was studied. Comminution characteristics were obtained using the one-size fraction method. The iron ore samples were crushed and separated into a number of narrow size fractions by screening. The size fractions were further divided by magnetic separation into three classes: concentrate, middling, and tailings. Subsequently, various size-grade classes were subjected to ball milling, and the results were analyzed in terms of the kinetic grinding model. The mineralogical textures of the grinding products were analyzed using mineral liberation analysis. The distribution of iron content within the size fractions was characterized by the beta distribution combined with the Andrew–Mica diagram. It was found that the grinding characteristics of the iron ore samples varied slightly with the iron content. However, the liberation characteristics were well described by the same set of liberation model parameters, regardless of composition. The variation in grinding kinetics with composition and the liberation model parameters was used in the combined comminution–liberation model to predict the evolution of the size-composition matrix as grinding proceeded. The predicted results agreed well with the experimental results. The developed model can be used to construct the yield–recovery graph and to calculate the liberation efficiency to determine the size reduction threshold for efficient separation. INTRODUCTION In mineral processing, comminution is usually the first step that ores undergo to liberate valuable minerals from gangue minerals. Generally, as the particle size decreases, higher liberation can be achieved. However, excessively small particles are unfavorable to subsequent processes, such as separation. Moreover, comminution is a highly energy-consuming process itself that accounts for approximately 60% of all energy used for processing. Therefore, there is a definite need to increase energy efficiency by applying adequate stress so that a high degree of liberation can be acquired at the coarsest size without overgrinding. To this end, it is essential to develop a model to predict the liberation of minerals as a function of size reduction."

Jan 1, 2018

By Magnus Evertsson, Haijie Li, Erik Hulthen, Mats Lindqvist

"The static and dynamic models for autogenous (AG) and semi-autogenous (SAG) mills have been studied for decades. Though the effects of mixing soft and hard ores in a mill and their interactions are not widely investigated. To develop a general numerical model for AG/SAG mills, a dynamic model has been introduced, and its capability to simulate multi component ore breakage has been examined and compared with previous publications. The simulation results show that the dynamic model can cover a range of milling conditions and is able to simulate complex scenarios with soft and hard ores. The dynamic model discussed here could provide substantial potential for the controlling and optimization of the comminution circuits. INTRODUCTION In the last decades, efforts have been devoted to studying the comminution circuit due to their high energy consumption. The energy directly spent in minerals comminution was about 2% globally in the year 2000 (Maurice et al, 2003). As one important part of the comminution process, AG/SAG mills are widely used for primary grinding in minerals processing. AG/SAG mill models include static and dynamic models (Kojovic et al, 2012; Yu et al, 2014; Yu et al, 2017; Liu and Spencer, 2004; Salazar et al, 2009). Many static models have been well validated over the past decades, but they are all based on steady state assumptions. Even though plants experience a steady-state condition under certain circumstances, it can be inaccurate to simulate the system by static models under all circumstances (Asbjörnsson et al, 2013). The advantages of a dynamic model are apparent that it provides more information and insights both inside the mill and through interactions with other machines in terms of pebble crushers, conveyor belts, screens and so on. In many mines, the multi-component grinding is inevitable, and the ratio of hard and soft components in the mill strongly affects mills operation and performance. Bueno (Bueno et al, 2010; Bueno et al, 2013) studied the effects of blending hard and soft ores in AG/SAG mills and used them to update the JKSimMet toolkit which was a steady state plant simulation software. However, due to the complexity of the particle interactions such as multi-component breakage function, appearance function, in mill transportation, there has been no dynamic AG/SAG mill models developed yet for simulating multi-component."

Jan 1, 2018

By Crasta Jeason, T. Sreenivas, M. Narasimha

The subtle nature of the flow inside the hydrocyclone has encouraged development of mathematical models for predicting its performance, which are widely used in simulation of comminution circuits. But most of the models available are based on single average feed density. But the feed to hydrocyclone classifier is generally mixture of particles of different densities. This effect of varying density of feed particles on performance of hydrocyclone has been reported in literature. Further investigation of the effect of multi component feed on the performance of hydrocyclone is the objective of this work. This work involves experimental work to study multicomponent behaviour in various size cyclones. The performance of hydrocyclone for feed mixture of magnetite and quartz has been studied. The effect of presence of magnetite, a high density material on efficiency of separation of quartz has been analysed. It was observed that the effect of component interaction increases with feed solids concentration leading to an increased cut-size for a given optimum cyclone conditions. Based on the multi-component exiperiments available in literature, a concept for modeling the performance of hydrocyclones is proposed. A set of semi-empirical model equations for cut-size, sharpness of separation are presented. An attempt to validate the new hydrocyclone model on multi-component behaviour is made.

Jan 1, 2014

By Ibrahim Alp, Ersin Yazici, Oktay Celep, Haci Deveci

Low extractions (<80%) in cyanide leaching impose the application of physical and chemical pre-treatment methods (e.g., ultra-fine grinding, roasting, alkaline leaching) prior to cyanide leaching to achieve acceptable recoveries. The effectiveness of the selected pre-treatment method is linked intimately with inherent mineralogical properties of ore. In this study, a refractory silver ore assaying 145 g/t Ag was subjected to various pretreatment tests in an attempt to eliminate its refractoriness. Direct cyanidation of the ground ore (d80: 65 µm) produced a low silver extraction of only 29.5% over 24 h indicating its high refractoriness. Previous studies have shown that silver occurs mainly as Sb/As containing sulfide minerals such as pyrargyrite (Ag3SbS3), tetrahedrite (Cu12Sb4S13) and proustite (Ag3AsS3), which do not respond well to cyanide leaching. Also, silver-containing minerals are closely associated with and/or encapsulated in other mineral phases that can restrict the contact of cyanide with silver. Therefore, alkaline leaching (using 3 M of Na2S, NaOH or KOH solution) and ultra-fine grinding as pre-treatment methods were tested to improve the extraction of silver. All the alkaline leaching tests were carried out for 3 h at800C. Neither NaOH nor KOH leaching produced the desired effect on the extraction of silver (i.e., ~30%). Even, a sharp decrease in the extraction of silver (i.e., 10%) was observed in Na2S leaching. On the other hand, ultra-fine grinding (UFG) (d80: 3 µm) substantially improved the extraction of silver in cyanide leaching (95% Ag at 24 h after UFG). It can be inferred from these findings that the refractoriness of the ore is essentially physical in character (i.e. the encapsulation of silver presumably in non-sulphide minerals such as barite and quartz).

Jan 1, 2014

By Paulo Sérgio de Oliveira, Joaquim D. Donda, Andreia C. Rosa

"The search for energy efficient technologies for comminution processes is constant in mineral processing studies, since those processes represent a major percentage of operational costs. In this context the use of stirred mills is increasing, especially for ultrafine grinding. Although many authors claim that these new equipment are more efficient than the conventional ball mills, there were very little chances to prove that in a practical way, since there are few industrial circuits where those technologies perform the same duty. Therefore, the regrinding circuit of Germano second concentrator offers an interesting opportunity: a vertical mill operating in parallel with two ball mills. During almost two years of operation, several sampling campaigns were conducted to evaluate the vertical mill performance and to compare the operational data of the three mills. The industrial data was also compared to jar mill tests results, which are monthly conducted in Samarco labs in order to predict the specific energy consumption required by the ore fed to these circuits. The vertical mill demonstrated the same ability to achieve the product specifications of the ball mills while proved to be able to reduce the medium specific energy consumption in about 40%."

Jan 1, 2014

Calcium carbonate has three polymorphs: calcite, aragonite, and vaterite. Needlelike aragonite CaCO3 with a high ratio of length to diameter (aspect ratio) is widely used in plastics, rubber and ceramics as a filler and in pigments and paints as a carrier. This paper investigated the influence of H3PO4 dosage, reaction temperature, CO2 flow rate, and initial Ca(OH)2 concentration on formation of needlelike aragonite CaCO3. It was found that the presence of H3PO4 in Ca(OH)2 suspension resulted in rapid formation of (Ca5(PO4)3(OH)) crystal nuclei, which facilitated nucleation and growth of aragonite CaCO3 on the formed (Ca5(PO4)3(OH)) crystal surfaces. The results revealed that H3PO4 addition of P/Ca of 0. 2~0. 3, high temperature of 75~85 °C, low CO2 flow rate and initial Ca(OH)2 solid concentration of 1. 5 %~5. 6 % are beneficial to formation of aragonite. Well crystallized needlelike aragonite CaCO3 whiskers with length > 20 µm and aspect ratio > 15 were directly synthesized.

Jan 1, 2014

By Longjiang Li, Mao Jiang, Zhihui Shen, Guizhou University, Yin Pan

This paper aims to study the influence and action mechanism of collector Y-89 on the flotation of auriferous pyrite. The measurement to identify adsorption quantity, IR and XPS spectrum analysis and flotation experiment made on the pure mineral were conducted. The research results show that when the dosage of MIBC is 20 mg/L, and pH of 8, the dosage of Y-89 over 60 mg/L, the pyrite recovery rate is greater than 80%.And when the dosage of Y-89is 60 mg/L, dosage of MIBC 20 mg/L, the pH in a wider range (pH=4~9), the recovery is greater than 75%. When the pH is above 10, the pyrite is depressed and its recovery rate is found to be dramatically dropping. Adsorption quantity measurement also shows that the strong alkaline conditions inhibit the adsorption of Y-89 on the surface of auriferous pyrite. IR measurement indicates that chemisorption of Y-89 occurs on the surface of auriferous pyrite. XPS spectrum analysis indicates that without adding Y-89, oxidation reaction occurs on the surface of pyrite. But when Y-89 is added, the chemical environment of Fe on the surface of pyrite has changed. Such findings indicate that with Y-89, chemisorption occurs on the surface of auriferous pyrite.

Jan 1, 2014

By Wang Xu, Tao Dongping, Zhang Jie, Tao Youjun

Based on the principle of fly ash triboelectrification, the mineral electrical index and testing method are introduced. The electric differences of various mineral components of fly ash are discussed in view of the results of chemical and mineral composition analysis of the fly ash sample acquired from the Xin-wen power plant. The dielectric constant and charge-mass ratio of carbon and ash in the fly ash are determined. The data were then used along with the rotary triboelectrostatic separator (RTS) testing results to investigate the charging characteristic of fly ash particles in different sizes. The results show that the dielectric constant of fly ash with different particle size decreased with the decrease in particle size, which led to a poor electrical conductivity. Thus particle size has an important effect on conductivity. The charges of carbon and ash particles increased with decreasing particle size. The charge-mass ratio of carbon and ash particles of the same size increased with decreasing particle size. This indicates that finer particle size is more favorable for triboelectrification separation from the charging efficiency point of view. The rotary triboelectrostatic fly ash separation tests show that the best decarbonization performance was achieved with particles in the size range of 0.038-0.074mm with which the decarbonization rate and efficiency index reached 38.93% and 120.83% spectively.

Jan 1, 2014