Search Documents

By G. Prabhulingaiah, D. M. R. Sekhar

"A phosphate deposit of estimated 6 billion tons of P2O5 is located 180 to 300 meters below the sea level, 185 kilometers north of port Luderitz, Namibia. The ore bed is 6 kilometers wide and 220 kilometers long. The ore deposit analyzing 16% P2O5 is loose sediment of 1.5 meters thick without over burden. Sizing of the ore to - 1.4 mm + 0.150 mm improves the grade to 23.54% P2O5 with a P2O5 recovery at 83.75% containing phosphate pellets and flakes of sea shells. Clay, bacterial debris as organic matter, flakes of broken sea shells and fine phosphate containing particles report to - 0.150 mm fraction and + 1.4 mm fraction contains sea shells and few phosphate containing pellets. The mineralogical composition of phosphate containing pellets is estimated (Droste, T.C., 2004) 80% frankolite, 6% pyrite, 4% illite, 3% quartz, 3% amorphous SiO2, 1% carbonates, 1% organic carbon and = 1% ilmenite, magnetite, zircon etc. The phosphate content in the pellets is around 27.7% P2O5. Trials to separate by gravity or flotation processes were not successful. Leaching of carbonates (sea shell flakes) under mild acidic condition (= 2% acetic acid or HCl solutions) or calcinations followed by leaching however yielded residues (concentrates) of grades 27.85 - 32.74% P2O5 at P2O5 recoveries ranging from 78.45 - 96.8% P2O5."

Jan 1, 2014

By J. B. Rubinstein

"The paper gives an overview of the history of flotation machine development. The laws of their evolution are stated and the place and role of column flotation are demonstrated.The major parameters of column cell diameter and height are discussed. Options are proposed for optimization of the hydrodynamic characteristics of large-capacity column cells. The high efficiency of columns with cell height of 4-6 m is demonstrated. The optimum parameters of multisectional column machines are determined. Their advantages compared to monocells are shown. A scaling-up procedure for column machines was developed based on flotation macro- and microhydrodynamics simulation."

Jan 1, 2003

By Sergey Ulianov, Arkady Senchenko, Alexey Shvets, Arkady Bakotin

"This paper contains description of research results of technology development for copper recovery from weathered tails of iron processing plant. The predominant host mineral that contains valuable component is chalcopyrite occurring in its free form and in associations with ore and rock-forming minerals. Copper grade is 0.26-0.30%. Emulsion inclusions of chalcopyrite in pyrite and sphalerite were noted. Major problem is low copper recovery (30-35%) by flotation. When studying chalcopyrite in primary concentrate it was determined that the surfaces of many chalcopyrite grains are covered with oxide films which prevented collector attachment onto them. Second issue was deep association of chalcopyrite with pyrite and sphalerite. Sulfidizing reagent addition did not help to reach the required level of copper recovery to concentrate. In the result of research performed the technological flowsheet was developed including preliminary treatment of head material in a special unit aiming at oxide films removal, followed by copper rougher flotation on head size tails, crude concentrate regrinding and a number of cleaner flotation operations. After the treatment of weathered tails according to the flowsheet developed, copper recovery to flotation concentrate became 71.53%, at 23.46% copper grade. The suggested technology allows one to solve the issue with treatment of technology-related copper-containing stockpile material, as well as to include the ores where copper is represented by sulfide minerals covered with oxide films into processing."

Jan 1, 2014

By Francisco Vicuña, Miguel Becerra, Gonzalo Montes-Atenas

"The optimization of the copper recovery from smelting slag by a process of comminution / flotation has been a widely discussed topic during the last few decades. Several studies covering the characterization of different types of slag, the impact of the slag cooling rate and of different flotation operating conditions on the flotation performance have been widely published. Currently, at El Soldado mine site (Angloamerican), there are large copper bearing slag deposits that can be a profitable alternative for the concentrator with capacity to treat this material. Under this process schema, the optimization of the flotation process to obtain better copper recoveries is a relevant topic of study. The aim of this study is to assess the efficiency of a sulfidation stage of a slag and to correlate that process with copper recoveries results in a flotation circuit. This article presents a detailed examination at both laboratory and plant scales of the slag sulfidation on the recovery of copper in the flotation process. The experimental methodology involves studying the effect of the sulfidation agent dosage, the pH, the particle size distribution of the flotation feed and the conditioning time. Furthermore, the performance of the sulfidation stage was analysed through the XPS analytical technique. It was observed that the sulfidation of particles in floatable size fractions correlated well with the increase in copper recovery. The results indicated that it is possible to increase between 2 to 4 points the total copper recovery with a sulfidation process implemented appropriately."

Jan 1, 2014

By Y. L. Tian

Low-grade bauxite with A/S of 4.4 from Henan province was used as raw material and the selec-tive grinding of bauxite, grinding efficiency, particle size and Al2O3 and SiO2distributions of ground products were investigated using ball and vibration mills. The results show that the selective grinding can be used to realize the separation of aluminum from silicon within a certain particle size. The optimal grinding conditions of the ball mill with bauxite are as follows: grinding material to charge ratio, 1.2, charge volume ratio, 40%, pulp con-centration, 70wt%, medium size distribution, F30mm:F20mm:F15mm=20%:50%:30%. Under the conditions, the weight rate of ground product with A/S over 7.5 is 27% and the recovery of Al 2O3is 30%. The optimal grinding condition of the vibration mill with bauxite are as follows: grinding material to charge ratio, 0.9; charge volume ratio, 70%; concentration, 70%; medium size distribution, F40mm:F30mm:F20mm=20%:30%:50%. Under the conditions, the weight ratio of ground product with A/S over 7.5 is 25% and the recovery of Al 2O3is 27%. The research is significant for the rational and economical utilization of the low-grade bauxite.

Jan 1, 2014

By Venkata S. Buddhiraju

Pelletization of iron ores involves balling on a rotating disc to produce wet pellets and induration of wet pellets on a moving grate to produce fired pellets. The quality of pellets produced and the productivity of the pelletization process depend strongly on the characteristics of the feed to the pelletization disc, especially the particle size distribution and the moisture content. The upstream processes involved in the preparation of pelletization feed include grinding, thickening and filtration of the iron ore slurry. The focus of the present work is the closed circuit wet grinding of iron ores. The circuit consists of a primary ball mill, a regrind mill and a hydrocyclone. A population balance model was developed to predict the grinding kinetics and an empirical model was fitted for the separation of fine particles from the coarse particles in the hydrocyclone. Batch grinding kinetics experiments were performed on a laboratory scale ball mill to obtain the ore breakage parameters which were subsequently used for the simulation of the industrial mills. The models were customized for the industrial operations and the effects of different process variables like feed flow rate, water flow rate, etc., on the size distribution of product from the grinding circuit were studied. Additionally, different circuit configurations were simulated to determine operating conditions that could result in the desirable product particle size distribution. The results of simulation were in close agreement with plant observations and the new circuits explored through simulation have helped in identifying potential opportunities for process optimization and control

Sep 1, 2012

By Graeme Jameson

"In current flotation circuits it is customary to grind the whole of the mill feed to an initial size, which is determined by the liberation characteristics of the ore, and the ability of the flotation machines to float the fully liberated particles. Usually, the product of the primary mill will be ground further in a ball mill, to improve the liberation of the values and hence the product grade, before passing to rougher flotation cells. The final grind size is ore-dependent, and is a balance of factors including the relation between surface liberation and grind size, the grain size of the valuable particles within the host rock, and the feed grade. The P80 for the feed to flotation may be as high as 300 µm for free-milling copper ores, and as low as 53 µm for finely disseminated complex ores. The grinding of the feed ore requires considerable input of energy. The rate of replacement of wear components such as mill liners and media, is proportional to the energy input. The costs of these two factors - energy and wear - are usually comparable and together they form the major part of the running costs of a concentrator, and indeed, of the whole mining operation. The energy required increases as the final grind size decreases. This talk will focus on the reduction of milling costs that could be achieved, using a fluidized bed flotation technology that can give high recoveries at coarse particle sizes. A number of different circuit designs will be presented, using the new technology. Calculations show that reductions in the running costs of a mine and associated concentrator of the order of ten to twenty percent could be achieved."

Jan 1, 2014

By W. Z. Yin

With increasing of mining depth, many iron ores in Liaoning Province contain carbonates such as siderite and ankerite. The emergence of these carbonates in ores creates a fatal impact on the running producing process of anionic reverse flotation in Dong Anshan Sintering Plant, which leads to ?concentrate and tailing no separated?. And its reason is still unknown. Moreover, siderite, despite that its ferric theoretic grade is only 48.2%, however, do not affect the blast furnace utilization factor, therefore, can be used as raw materials in ironmaking. In order to solve the separate problem of iron ore containing carbonates, five pure minerals, martite, magnetite, quartz, siderite and ankerite, were selected for a series single flotation experiment. The aim was to discover the flotation difference of these minerals, furthermore, to explore a new flow sheet for the iron ore containing carbonates. The results of single mineral flotation experiment reveal that the combination regulators, starch and CaCl2, in different pH extent, can make these minerals taking on obvious flotation difference, which make it possible to process the iron ore containing carbonates. A new flow sheet, step-flotation, to process iron ore containing carbonates is explored, that is, first step, direct-flotation processing, is to eliminate the bad effect that the carbonates bring in flotation system by collecting carbonates under neutral condition; the second step, reverse?flotation processing, is to get qualified iron concentrate by collecting quartz under alkaline condition. Manual mixed ore sample were processed successfully through this new flowsheet under proper reagent system, which has absolute advantage compared with routine flowsheet. Actual ore sample of compound magnetic separation concentrate were processed successfully both open and closed circuit experiment through this new flowsheet. SEM and EDS were used to probe the reason why carbonates affect the regular processing. It is analyzed that moderate floatability of siderite and its coating on the surface of hematite and quartz make the phenomenon ?concentrate and tailing no separated?. This research provides a reasonable processing scheme for iron ores containing carbonates and can be used for reference in processing other complicated, refractory iron ore.

Jan 1, 2014

By L. Y. Zhang

The metallic sulphides in Jinchuan Mine are relative friable and the gangue minerals suffer of wide secondary change, the overgrinding of metallic sulphides and sliming of gangue minerals are the main cause that makes the mineral separation indexes difficult to improve. So changing the process of grinding, and classification, and optimizing the particle size distribution of grinding product is the key improving the separation performance of Jinchuan nickel and copper ore.

Jan 1, 2014

By R. ?. Sherembayeva, ?. ?. ?uktybayeva, ?. B. Rakhimbekova, N. ?. ?m?rova

"Studying the interaction of the phosphorus-containing flotation reagent with the components of the flotation system ""liquid-gas-solid"" during flotation of non-ferrous metal ores allows regulating the enrichment process. The phosphorus-containing reagent-collector anabasinium-O,O-dimethyl-thiophosphate has beensynthesized under laboratory conditions and the concentrated aqueous solution of anabasin hydrochloride and the 40% solution of sodium hydroxide have been used as the raw material. The phosphorus-containing reagent has been obtained by interaction of the anabasine base, sulfur and dimethyl phosphite, due to sulfur and nitrogen atoms it can form complex compounds with heavy metal ions.Studying flotation of copper-sulfide ore of the Sayak field with the use of the phosphorus-containing reagent-collector anabasinium has been performed in the open and closed cycles. The degree of ore grinding was 60- 62% of the class -0.074 mm. There has been established the dependence of the ore flotation parameters on: a) pH of the pulp; b) the consumption of the reagent-collector anabasinium.The effect of the pulp pH on the technological parameters of copper ore flotation has been carried out with a reagent regulator that increases the difference in the surface properties of the minerals to be separated.There has been used lime as the regulator of the medium, the consumption of which varied from 750 to 1500 g/t; the consumption of the reagent-collector anabasinium was 10, 15, 20 and 25 g/t.It has been found that when flotation of copper ore without the use of lime at pH equal to 7.8 and at the reagent consumption, g/t: anabasinium - 25, T-92 - 55, copper recovery in the concentrate is 92.72%, the quality of concentrate is 7, 1%.In flotation according to the factory mode (the consumption of xanthate is 44 g/t, T-92 is 55 g/t, pH = 7.8 (without lime)) of copper ore, copper recovery in the concentrate is 87.38%, the concentrate quality is 7, 97%, with reducing the xanthate consumption to 25 g/t copper recovery is reduced to 83.39%, the quality of the concentrate is up to 6.69%.In the experiments using the factory reagent mode in the closed cycle, with the xanthate mass consumption of 44 g/t, T-92 blowing agent of 55 g/t, the third recleaning concentrate contained 19.13% copper with recovery of 86.89%.Using a phosphorus-containing reagent instead of xanthate with the same flow rate, the third recleaning concentrate with the mass fraction of copper of 19.82% has beenobtained with recovery of 87.77%."

Jan 1, 2018

By Ray Everson, Henry Kasaini

"Adsorption of Pd (II) anions on the surface of activated carbon (Norit 0.8) occurred at high proton concentration (0.01 – 2.5M, HCl) in the feed and averaged 27 mg/g. The adsorption process was interpreted in terms of surface ionisation and adsorption model. Enthalpy of adsorption averaged 0.4 kJ/mole indicative of an instantaneous physical adsorption process. We found that the Toth isotherm fit the adsorption data fairly accurately. A combination of the Langmuir and Freundlich equations yields an effective three-parameter Toth equation (1) which is frequently used to describe adsorption on heterogeneous surfaces.Figure 1 shows the comparison between experimental results and the model isotherms. We found that Langmuir isotherms underestimated the adsorption capacity on the porous surface while the Freundlich isotherm overestimated adsorption. Furthermore, the surface coverage at equilibrium was well described by both the Langmuir and Toth isotherms. But, Freundlich isotherm predicted a surface fraction coverage that was higher than unit. Based on better prediction of surface coverage and a reasonable fit to adsorption data, we concluded that the Toth isotherm best described the adsorption data of palladium. The adsorption process was limited by mass transfer resistance through the external film. We estimated the rate constant from equation (2), where e, ?b, and rp are porosity, fluid density and particle radius, respectively"

Jan 1, 2003

By M. S. Eygi

This study covers the investigations based on the electrokinetic and rheological properties to explain the interactions between kaolin minerals and commercially available polyelectrolyte in anionic character. Additional adsorption test were also conducted to support the interaction mechanism. Adsorption tests showed that adsorption densities decrease by increasing the solid content. In-creasing the solids contents from 1% to 30% by weight resulted in the decrease on adsorption from 2.14 mg/g to 1.85 mg/g. Because of its difficulty, the solids ratio at 70% was not studied. However, following to trend of the curve plotted adsorption density-solid ratio, an estimation was made and adsorption density at 70% solid content was extracted from the curve as 1.75~1.80 mg/g. The electrokinetic studies pointed out that the presence of polyelectrolyte increase the zeta potential of kaolin from 40 mV to 60 mV which is reasonable conditions to disperse and stabilize the kaolin slurry and lower the viscosity. When these result of the different tests are combined and considered together, 2 mg/g polyelectrolyte concentration was noted as optimal concentration where adsorption density, viscosity and zeta potential of the slurries give maxima and remain constant after this concentration.

Jan 1, 2014

By Abhakumari

Effect of applied DC potentials on the bioleaching of a chalcopyrite concentrate in the presence of Acidithiobacillus ferrooxidans is discussed. Copper dissolution was the highest at an applied potential of +600mV (SCE), while all the dissolved copper got cathodically deposited at a negative potential of -600mV (SCE). Electrobioleaching at an applied potential of +600mV (SCE) was established at different pulp densities as a function of time. Effect of the magnitude of electrolytic currents on the activity and growth of bacterial cells was studied. Preadaptation of bacterial cells to the concentrate slurry and electrolytic growth conditions significantly enhanced copper dissolution. Electrochemical and biochemical mechanisms involved in electrobioleaching are illustrated with respect to oxidative dissolution and bio catalysis of anodic oxidation.

Sep 1, 2012

By Robert Dunne

A review of the current ?state of the art? of refractory gold treatment will be provided. This will include a global perspective of the refractory processes that are being practiced, where they are and some discussion on why the processes were selected. Some discussion on the challenges that face the refractory gold industry will also be provided.

Sep 1, 2012

By Rodrigo Ladrón, Gonzalo Rund, Gonzalo Montes-Atenas

Modelling ore comminution processes have been a highly fruitful scientific topic. The models have been proved to be largely dependent on the selected comminution technology. Among them, semiautogenous (SAG) mill technology has been widespread implemented in plants but no complete understanding of the mechanisms involved in the process is available. Tracing back in history, SAG models considered only some granulometric cut sizes such as the t10 and attempted to relate these parameters with the energy involved in the impact between particles. Other models evolved towards incorporating physical properties of the material being ground and the mill operating conditions. These material properties have assisted to obtain a more comprehensive description of the breakage mechanisms; nevertheless, the gathering of all known parameters still have not delivered a model able to describe the process. This may be a result of emergent properties or phenomena originated from interactions inside the process which are hard to predict turning the size reduction operation into a complex system. Cellular automata provide one answer to describe complex systems by following simple rules. The aim of this research work is to establish the preliminary rules of thumbs enabling the implementation of cellular automata able to predict the particle size distribution at the exit of a SAG mill. The methodology involved developing a simple 2D model of a ROM sample. Plant data from two mine sites were correctly described by a set of three rules: two rules describing the particle reduction and one rule associated with material transport across the mill. Further analysis related with expanding this model to 3D and its impact on the liberation of valuable material is also discussed.

Jan 1, 2014

By Liu Yong

A complex rare metal ore, containing various valuable elements is used in this study. The mineralogy results indicate that the mineral composition of the raw ore is complex, and there are more than thirty-eight kinds of minerals in the raw ore, and the elements, such as Nb, Ti, Fe, REO, Be etc, always form isomorphism relationship. The REO content of the raw ore is 0.45%, and the contents of other rare metals Nb, Ta, Ti and Zr are 0.33%, 0.02%, 0.93% and 2.00% respectively, and the main gangue elements are Si and Al, and their contents are 71.84% and 8.5% respectively. The beneficiation-metallurgy combination process of ?preconcentration-reduction and magnetic separation-acidification and leaching-precipitation? is used to treat the raw ore. The preconcentration of raw ore is realized through high intensity magnetic separation, and the magnetic field intensity is 1.0T, and the rough concentrate with 2.88% REO and 1.95% Nbresidue can be obtained, and the iron recovery is 92.83%, and the REO recovery is 95.87%, and the Nbresidue is treated by hydrometallurgy process of ?acidification-leaching-precipitation?, then the rare earth oxide, niobium concentrate and zircon-bearing residue can be obtained, and the REO recovery is 80.10% and the Nbresidue and the gangue obtained from the high intensity magnetic separation process is separated by gravity separation, and then the zirconium concentrate can be obtained. The indexes of the beneficiation-metallurgy combination process used to treat the complex rare metal ore are as follows. The REO content of the rare earth oxide is 92.58% and the recovery is 58.44%. The Nb2O5 and 27.42% TFe can be obtained. Iron in rough concentrates is removed after reduction and low intensity magnetic separation, then the iron powder with Fe content over 88% and nonmagnetic rare-metal 2O5 recovery is 94.77%. The rare-metal 2O5 recovery is 80.04%. The mixture of the zircon-bearing 2O5 content of niobium concentrate is 28.34% and the recovery is 54.02%. The ZrO2 content of zirconium concentrate is 28.43% and the recovery is 52.35%. The TFe of iron powder is 89.53% and the recovery is 78.13%. Keywords: rare metal ore, separation and extraction, beneficiation-metallurgy combination, comprehensive utilization

Sep 1, 2012

By S. Fiore, M. C. Zanetti, C. Clerici

The processes and fluxes of a cast iron foundry plant located in the North of Italy were analyzed in order to determine the amount and kind of wastes produced from the different activities. The main fractions are the molding sands, furnace muds and powders coming from the dust abatement plant, the exhaust lime, the furnace refractory, the metallic shotting and the sludges and powders coming from the dust abatement plant of molding lines for a total production equal to 800 t/d. All wastes were sampled and particle-size and chemically characterized to evaluate the best recycling or reuse solutions. Wastes were sieved and divided in three categories according to the particle-size dimensions: below 0.1 mm, between 0.1 and 0.6 mm and above 0.6 mm. The fraction above 0.6 mm dimension underwent magnetic separation to recover and quantify the potentially available iron fraction. The fraction between 0.1 mm and 0.6 mm was chemically characterized in order to understand if it could be fed to the sand regeneration plant. The below 0.1 mm fraction was characterized to evaluate the following recycling and reuse solutions: additive for molding sands and/or raw material for the concrete industry.

Jan 1, 2003

By R. Kobialka

In the article results of experiments over jaws? linings in jaw crushers with different shaping of working surface were presented. Following sets of jaws were under investigation: immobile plain jaw and moving jaw with grooving surface. Grooving jaws have groves with circular, triangular and trapezoid cross section. In order to evaluate efficiency of comminution both the grain composition of product and the content of irregular grains were determined, as well as the size of crushing forces and process efficiency were measured. For the combination: plain jaw with grooved one, a good results were obtained as regards the grain composition of product and the content of irregular grains. Crushing forces were higher at crushing with mixed types of jaws (the one plain, the second grooved), in comparison to crushing with using both grooved jaws. Efficiency of the process was definitely higher for mixed jaws.

Jan 1, 2014

Systemic process mineralogy study on Baerbulawu refractory hematite ore in Kazakhstan has been carried out. The ore contains Fe 41.34%, and 87.26 % of which exists in hematite. Most hema-tite occurs as fine or ultrafine grains and its average size is only 0.015mm. The gangue is mainly composed of quartz, mica, chlorite, kaolinite and other clay minerals. The liberation of hematite is only 66% when the ore is grinded to 75% ?0.074mm, while part of gangue is already liberated from hematite under this grinding condition, so these gangue can be cast away by magnetic separation in advance. Hematite will not liberate completely from gangue untill grinding fineness reaches 86% ?0.038mm, at the same time, free particles of ultrafine hematite tend to coagulate randomly with quartz and clay minerals, so appropriate dispersant is necessary to pre-vent hematite and clay minerals from coagulation. Based on the process mineralogy research, final technology flowsheet is high-intensity magnetic separation by coarse grinding?rough magnetic concentrate regrinding?inverse flotation, and an ideal index is achieved. The yield of final iron concentrate is 43.46%, and its grade and recovery are 66.76% and 70.55% respectively. The research result is also useful to other similar iron ores.

Jan 1, 2014

By Z. He

Based on full investigation of the characteristic of sphalerite in the residue obtained from cyanidation leaching process and the study of the mechanism of the interaction between flotation reagents and sphalerite with the aid of electrochemical analysis, the reagent named YO was developed for eliminating the depression effect of CN- on sphalerite and reducing the dosage of CuSO4. The achievements have been used in commercial production for the treatment of the cyanidation residue to recover the zinc minerals, obtaining a zinc concentrate with grade of 56.49% Zn and recovery of 86.63% Zn.

Jan 1, 2014