Search Documents

By Hao Zhang, Dezhou Wei, Qiang Zhao, Caie Zhang, Baoyu Cui, Xuetao Wang

"Nowadays, long periods of relatively low iron ore prices have made the steel industry get the greater pressure. To develop appropriate processing technology based on characteristics of the iron ore, so as to reduce the beneficiation costs, is crucial to the improvement of iron and steel enterprise competition. For a typical low-grade iron ore from northeast China, beneficiation process research was conducted based on the in-depth studies of ore characteristics. Results show that the iron grade of the ore was 31.56%, the content of FeO was 6.59%, the main iron minerals were hematite and magnetite with fine dissemination sizes and partly scattering in gangue; With the grinding fineness of 65% passing 0.074mm, and regrinding fineness of 90% passing 0.074mm, the concentrate with 66.80% iron and recovery of 82.90% was obtained via the combined flowsheet of stage grinding – classification – gravity concentration – low and high intensity magnetic separation – reverse flotation. Ratios of gravity concentration and low intensity magnetic separation were 70.21% and 7.57% respectively in 40.42% of total concentrate yield; The loss of micro-size fractions can be reduced by feeding spiral tailings into magnetic separation and flotation; It’s helpful in reducing the dosage of reagents and beneficiation costs by increasing the throughput of gravity concentration and outputting concentrate of low intensity magnetic separation.INTRODUCTION Iron and steel industries are facing the increasing pressures in the continued falling iron ore prices. In order to improve the competitiveness, it is extremely urgent for them to develop more appropriate separation process for the reduction in iron ore beneficiation cost. As a typical low-grade iron ore, Anshan-type iron ore is one of the most important iron ore resources in China [1-3]. The flowsheet of stage grinding and separation contained the classification of the coarse particles and the fine particles, the gravity concentration, the magnetic separation and the anionic reverse flotation has been widely applied for Anshan-type iron ore. With the appropriate separation progress as well as equipment, satisfactory separation results had been obtained, and mineral particles with different size were recovered separately [4-7]. However, the low recovery of fine mineral particles and the relatively high beneficiation costs still prevented the efficient application of the process [8]. For a Anshan-type low-grade iron ore, a typical process flowsheet, as mentioned earlier, with stage grading, classification of the coarse particles and the fine particles, gravity concentration, magnetic separation, anionic reverse flotation was adopted currently. And the concentrate with 67.10% iron and recovery of 75.50% was obtained and the gravity concentrate accounted for 39% of the total concentrate. However, a large amount of fine liberated iron ore particles were lost in the tailings."

Jan 1, 2018

By Valentin V. Shatalov, Irina V. Pastukhova, Alexander V. Kurkov

"We have developed a technology to improve the quality of low-grade concentrates containing minerals of tantalum, niobium and tin on the basis of given conception by the way of improving selectivity and using certain reagents composition. The basic collector presents a traditional or complex-forming collector used together with organic diphilic reagents – the secondary reagents regarding the basic flotation regiment, capable of forming associates with the main collector on the surface of the mineral, thus altering the interaction energy. In the given process the main collector is the fraction of hydroxamic acids C7-C9, the reagent of the secondary action – sulphosuccinamate, which added in moderate concentrations range provides for a synergistic effect.We have determined the parameters of the process stability and necessary modifying reagents for a selective recovery of tantalum, niobium and tin minerals from refractory products. Variants have been studied where the main collector and the secondary action reagent were substituted with some more efficient flotation reagents. A possibility of a more flexible reagent compounding for the process has been shown. The flotation process is highly stable regards the saline composition of the liquid phase in the pulp. It can operate under conditions of the complete water recycling with the total salt content up to 12 kg/m3, iron up to 1.2 kg/m3.The given results consider the efficiency testing of the suggested technology for the gravitation products, which were obtained from ores of various genesis and contain large quantity of the most refractory minerals, such as topaz (80%), gamet (55%), tourmaline (30%). High selectivity of the process has been registered with the metal recovery about 92-98%, which appears to be similar to hydrometallurgical operations under certain conditions."

Jan 1, 2003

By Joseph Kelly, Christopher Kelsey

This revolutionary super-fine crusher has the unique capacity to generate fine and ultra-fine products from single stage reductions of coarse or fine mineral feeds. The crusher consists of a rotating compression chamber and an internal gyrating mandrel. The axis of rotation of the shell is displaced relative to the axis of the vertically mounted mandrel. The inner surface of the compression chamber is machined as double cone frustums at an angle equal to the displacement angle. Crusher feed is accelerated into a compacted particle bed, which lines the inside of the compression chamber. The depth of the compacted bed progressively increases until the mandrel is engaged. The mandrel is then free to rotate with the compression chamber. Continued feeding increases power draw and triggers the counter rotating mandrel gyration drive. The gyrating mandrel delivers multiple compressions at high pressure to the rotating particle bed. High concentrations of energy are harnessed within a small active volume over short retention times. The combination of extraordinarily high power intensity and extreme compressive force results in primary compressive fracture and induced secondary tensile failure. The axially displaced rotation of the compression chamber effectively distributes the breakage forces throughout the particle bed. This paper covers open circuit, pilot trials on magnetite, perlite, garnet, marble and a copper/pyrite concentrate. Particular emphasis is placed on the extraordinary results achieved with trials on zircon and highly refractory fly ash. The extreme duties were deliberately chosen to demonstrate the crusher’s application scope and potential to impact capital operating and maintenance costs as the technology matures. Super-fine crushing, once considered impracticable has the potential to offer compelling options for the generation of ultra-fine products.

Jan 1, 2014

By D. Saramak

"High-pressure grinding technology is considered as one of the most efficient techniques of ore comminution, especially in terms of energy consumption. HPGR devices has been utilized in many mining-related industrial sectors, including iron and non-ferrous metal ores processing (copper, platinum, gold), as well as cement and limestone flour production. Even though the technology well known (introduced into mineral processing circuits in 80’s), there are still examples of ineffective operation of HPGR devices. This is a result of improper application of HPGR into individual crushing circuit. The purpose of the paper was to analyze selected effects achieved in HPGR on the course and effectiveness of beneficiation operations. Investigations were carried out for copper ore, and investigative programme was run for different values of HPGR pressing force, as well as changeable ore characteristics (content of fine size fractions, material moisture). All crushing products were then treated in flotation process, in order to determine useful mineral recovery. Results of investigations show that HPGR operating pressure influences the metal recovery in proportional way, however too extensive pressure values have relatively lower impact on increasing of the metal recovery. Particle size distribution of HPGR feed and its moisture have lower influence on recovery level than HPGR pressure, but too extensive moisture content influences the higher energy consumption of the roller press, together with less effective comminution. The second aspect raised in the paper was a possibility to control and optimize the HPGR-based circuit. There were presented the proposed approach to adjustment of HPGR operating parameters that enables the higher metal recovery.INTRODUCTION The high-pressure grinding technology, invented and developed by Professor Schoenert in 70’s (Schoenert, 1979), is currently regarded as one of the most efficient methods of hard ore comminution. Since then the technology was introduced into raw materials treatment circuits in many mining and mining-related industrial sectors, including iron and non-ferrous metal ores processing (copper, platinum, gold), as well as cement and limestone flour production. Considerable number of works concerning modeling and optimization of HPGR operation were also presented (Daniel & Morell, 2004, Tavares, 2005, Saramak, 2012, Saramak & Kleiv, 2013). Nowadays high-pressure grinding rolls devices are considered as well know technology with over 500 sold machines, according to various sources."

Jan 1, 2018

By Kozlov Andrey, Matveeva Tamara

"The results of mineralogical and technological studies of platiniferous dunites from Svetloborsky zonal massif (Urals platinum belt) are presented and the basic typomorphic signs of productive mineral assemblages are substantiated. The characteristic features of platinum ore mineralization are revealed: a wide range of iron-platinum alloys, enrichment of ore-formed system by the elements Os, Ir, Rh and activity of the S and As in it, intrusion of Fe-Ni sulfides in platinum and its fusion with magnetite. More than 80% of PGM mineral grains has size less than 100 microns, that determines the possibility of significant losses of platinum in the process of gravity separation and the need for additional recovery processes for small and fine fractions of platinum tailings and sludge products. Summarized results of laboratory tests of small-volume sample processing of platiniferous dunites are presented and the processing flow sheet is developed and tested. The flow sheet incorporates several stages, including stage-wise grinding and gravity separation of ore using the centrifugal concentrator Knelson KS-MD for differently sized material and flotation treatment of tailing products using new classes of reagents for additional recovery of PGM fines."

Jan 1, 2014

By Martin Rudolph

"Flotation is without a doubt one of the major processes for the separation of fine minerals and it has been applied for more than a century. A key task of a successful flotation separation is to find the proper chemical treatment to selectively hydrophobize and thus float a certain mineral phase using molecules or ions referred to as collectors, depressants, regulators and frothers. Commonly floatability is determined by microflotation tests using the Hallimond tube with pure mineral phases. This method however requires the pure mineral phase which is very often not even taken from the same deposit which is going to be processed. In this paper we present a new approach to in-situ determine and even map the floatability of finely disseminated mineral phases within cross-sections of an ore. It is based on measuring hydrophobic effects using colloidal probe atomic force microscopy with a hydrophobic polystyrene probe based on force spectroscopy with a lateral resolution of only a few nanometers. Coupled confocal Raman spectroscopy on the same locality enables the identification of the mineral phase. We present the working principles of the method and show which signals in the force spectra characteristic for hydrophobic interactions can be used to define floatability and which can then be mapped as single quantities, e.g. jump-into-contact events due to nanobubble occurrence or parameters of the long range interaction curves most probably due to capillary effects. A finely grained silicate ore containing the valuable rare earth mineral eudialyte from southern Sweden as well as pure samples of magnetite are presented as substrates to demonstrate the capability of this new approach. This method will not only help to find the proper flotation chemistry but it can furthermore help in researching and unravelling problems of floatability within similar mineral phases."

Jan 1, 2014

By Bertil I. Pålsson, Sture V. Persson, Kent T. Tano

"Autogenous (AG) and semi-autogenous (SAG) mills often operate in an unstable state because of the difficulty to balance the rate of replenishment of large ore particles from the feed with the consumption in the charge. This has led to an increased interest in obtaining an accurate and direct measurement of mill load and the behaviour of the mill charge. A problem in attempting to measure those parameters is getting a sensor that is both robust and sensitive enough for continuous on-line measurement.Techniques that measure the force acting on the lifter when it hits the charge inside the mill have got an increased interest recently because of the ability to combine it with DEM modeling. This paper presents a method for the measurement of the apparent filling level in a pilot ball mill equipped with the Metso Continuous Charge Measurement system (CCM). In this technique a strain gauge sensor is mounted on a flat steel spring which is fitted into a recess underneath a lifter bar. In addition, a conductivity probe, the Boliden Grinding Measurement System (GMS), is mounted in another lifter bar with the purpose of comparing the two measurements. To visualise the behaviour of the charge a 2D DEM modelling technique is used with Metso HFS software.The pilot mill is a grate-discharge mill, equipped with 12 rubber lifters of square size 0.1 m, face angle 45 degrees. Steel balls in the size range 10-30 mm and density 8000 kg/m3, are used in the experiments. Test material is a hematite pellet feed, d50 around 45um, chosen to get stable grinding conditions with respect to feed size variations.The experiment is meant as a first test of the equipment’s performance, and to study how the sensors respond to changes in some operating variables. To get an understanding of, and distinguish between correlation and causality, experiments are performed according to a full factorial design with two levels, and in addition two replicates of the experiments at a center-point in the charge level setting."

Jan 1, 2003

By Gülay Bulut, Ünzile Yenial

"Water composition has a significant effect on flotation. A better understand the role of water composition in flotation is very important for process quality and performance. Based on source of process water, the concentrations of the dissolved ions, hardness, contaminants and residual composition of reagents can varied in the process water. The various water resources employed during lead and zinc flotation caused activation, depression or selectivity effects on minerals due to the presence of different ions in solution. Metal ions in these water resources were adsorbed on the ore, whilst ions associated with gangue minerals were released into the flotation pulp.This paper includes a research for the effect of different water compositions on lead and zinc sulphide flotation. Experiments were carried out five types of water such as tap water, recycling water, tailing dam water, underground mine water and sea water. The ore sample was obtained from Esan Balikesir-Balya mine. The mineralogical study of ore sample shows that it contains mainly galena, sphalerite, pyrite, hematite, quartz, diopside, epidote, calcite, and chlorite. It is found that recycling water and tailing dam water has a positive effect on recovery of lead and zinc minerals and detrimental effect on content of both minerals. This result may explain with remaining reagents in these waters. Underground mine water and tap water gave nearly the same recoveries of zinc. Sea water affects the recovery lead and zinc negatively."

Jan 1, 2014

By Tiago de Souza, Caroline Gonçalves, Carlos Eduardo de Castro, Everton Dias

The Miraí plant from Votorantim Metais, has two screening stages to the bauxite classification after scrubbagem. The final product has hold the larger size of 0,84 millimeters (20 mesh). There are two sieves Haver & Boecker (model R-TE 3658 x 10972), which have four modules with cut size sieves of 10 mesh (1.70 millimeters) and ¼ inch (6.35 millimeters) on the primary screen, and 20 mesh (0.84 mm) on the secondary screen, all made of polyurethane. The actual configuration was established according to the empirical tests realized that aimed the increase material load on the secondary screening. However, having in mind the screening process improvement and use the fractions smaller than 0,84 mm, which have significant levels of Alumina and low reactive silica, was proposed a new test of change the sieves opening for 6 mesh in the primary screen and 28 mesh for the secondary sieve. The objective of this work was measure the ore alterations on the particle size distribution on the screening steps, increasing the plant weight and ratio recovery before and after the test.

Jan 1, 2014

By S. Banisi, A. R. Ghasemi, M. Maleki-Moghaddam

Direct observation of the charge shape and its motion in industrial mills are not possible, it is then customary to use transparent end, small-scale mills (i.e., model mills) to determine the charge trajectory directly by visualization methods. Because of a short length of the model mills, the end-wall effects could introduce a significant bias on the observed charge trajectories and shape. The shorter the mill, the stronger the bias. This could be due to some material bridging between the end walls. In this research, the end-wall effects were investigated by gradually increasing the model mill length and analysing the charge trajectory and shape variation at a given operating conditions (i.e., ball filling, mill speed, liner type). The unbiased mill length was assumed to be beyond the mill length where no significant change observed in the charge trajectory and shape. For all tests, the torque of the charge was also measured by a torque sensor. The special design of the model mill with the diameter of 100 cm made possible to increase the mill length in steps of 3.6 cm up to 21.6 cm. Four types of liners, five steel ball fillings (10, 15, 20, 25, 30% v/v) and three mill speeds (55, 70, 85% of critical speed) were tested. The ball sizes ranged from 4 to 12 mm. The results indicated that when the mill length was below 10.8 cm the end walls prevented the charge from free falling. This resulted in lower impact point angles and lower power draws compared with the case of no end-wall effects. When the same experiments were performed using an iron ore instead of balls with the same size range, the impact of end-wall effects was more pronounced. For an increase of 30% in the speed (from 55 to 85%), the torque due the change in the charge shape decreased by 41% (from 3.7 to 2.2 kgf.m) when mill filling was 30%. At the same operating conditions when steel balls used the torque decreased only by 19% (from 9 to 7.2 kgf.m). This was expected due to irregular shapes of the ore particles which facilitated bridging. Three-dimensional DEM simulations also resulted in the similar conclusions.

Jan 1, 2014

By D. Saramak

The proposal of the nip zone angle determination in HPGR crushing process is presented in the paper. Knowledge of the nip zone angle value, in turn, makes it possible to determine the real maximum pressing force in the high-pressure comminution. Two methods of determination of this maximum pressure were proposed and verified. The first method is based on the roll?s geometry, and the change of the HPGR chamber?s volume together with the roll rotation, while the second one considers the outlet gap width impact. Results of the nip zone angle calculations according to both methods are similar and show convergence with the real operating conditions. The verification was carried out in a piston-die press, and experimental results show that methodology of the nip zone angle determination presented in the paper has its practical confirmation. A proper determination of the nip zone border makes it possible to calculate the comminution probability of given type of material and is a basis for the HPGR crushing process modeling and optimization. Keywords: HPGR, comminution, nip zone, ore processing

Sep 1, 2012

By Glasswell K. Nkonde, Fredrick Chileshe, Steven Simukanga

Improving food security by increasing crop output is a primary objective for most countries in the sub- Saharan region. Most soils in the region are deficient in phosphorus an important nutrient after nitrogen in plant growth. Phosphates are therefore used together with nitrogen and potassium based fertilizers in improving crop production. Zambia like many other countries in the sub-Saharan region imports phosphate fertilizers for use by its farmers. However, indigenous phosphate deposits of igneous origin exist in Zambia of which the main ones are Chilembwe in Petauke district, Mumbwa sugarloaf in Mumbwa district, and Nkombwa Hill in Isoka district. If commercially exploited, these deposits could become a ready source of inexpensive phosphate for the local farming communities in the country. Previous research has shown that partially acidulated phosphate rock (PAPR) produced using Chilembwe phosphate rock is just as agronomically effective as the imported superphosphate fertilizers on food crops in most of the Zambian soils. PAPR is produced by reacting finely ground phosphate rock with only a fraction (usually 50%) of the stoichiometric quantity of the sulphuric acid required to fully convert the apatite in the rock to monocalcium phosphate thus making the process cheaper in terms of acid consumption than the poduction of single superphosphate where the apatite in the rock has to be fully converted to monocalcium phophate. The factors that affect the percentage of available P2O5 in the PAPR produced include particle size of phosphate rock, degree of acidulation, concentration of acid, process temperature profile, residence time and drying temperature. These factors were studied in a 25kg/hr PAPR pilot-plant in the School of Mines at the University of Zambia using Chilembwe phosphate rock. The PAPR pilot-plant consisted of a rotary drum granulator as the main reactor, a rotary drum dryer and a triple deck vibrating screen. Ground phosphate rock was reacted with sulphuric acid and water in the granulator to form a granular product which entered the drier. The dry product was screened into three size fractions. The 1 – 4 mm size fraction was the final product whilst the –1mm size fraction was recycled. The +4mm size fraction was sent to a crusher while the crushed PAPR was sent back to the screens.

Jan 1, 2003

By Daniel Saramak

"Issues concerning effectiveness of the high-pressure comminution process in technological circuits of copper ore treatment were presented in the paper. Crushing processes taking place in high-pressure grinding rolls devices (HPGR) are currently one of the most efficient methods of hard ore size reduction in terms of the energy consumption. The HPGR products are characterized by a fine particle size and the micro-cracks formation in individual particles, which appear in downstream grinding processes, decreasing their energy consumption. The purpose of this paper was to analyse the effectiveness of a ball mill grinding process depending on the changeable conditions of run for the HPGR crushing process. The research programme carried out included crushing tests in the laboratory scale HPGR device at various settings of the operating pressure volume and selected qualitative properties of the feed material (i.e. particle size distribution). Particle size distribution analyses of all HPGR products were performed and in the next stage the material was a feed to the ball mill grinding process. Grinding process kinetics were investigated through the determination of mass recoveries of individual particle size fractions after defined grinding time intervals. The models, defining the grinding process effectiveness as a function of changeable conditions of HPGR process run, were determined on the basis of obtained results. Based on these models the optimal grinding time in a ball mill was specified which is, in turn, the basis for optimization of operation of the technological comminution circuits for a given material type. The obtained results proved that the application of HPGR devices in a given copper ore comminution circuit may improve the effectiveness of the downstream grinding process which leads to improvement of the entire circuit work efficiency through decreasing the process energy consumption and enhancing product size reduction."

Jan 1, 2014

By Alim Gül, Güven Önal

"Recently, there have been some attemps on the treatment of low grade ores and old plant tailings due to the decrease in high grade ores and the increase in the metal consumption with increasing world population. Cost of mining and beneficiation of low grade ores become prohibitive since the costs of grinding before flotation make the process unfeasable. Therefore, preconcentration of these ores prior to flotation becomes more important. The concentration of ores preconcentrated in coarse sizes provides a decrease in investment costs as well as grinding and flotation costs. Additionally, the requirements of less space for tailing disposal and less reagent consumption are also important from the viewpoint of environmental considerations.In this study, ore sample containing 0.6 % Cu and taken from Küre-Asiköy ore body was used. Ores contained chalcopyrite and pyrite as main minerals and diabaz, quartz, chlorite and sericite as gang minerals.Samples were all crushed under 9 mm by considering the preliminary studies and float and sink experiments were carried out with the sample in the size range of –9+1 mm using different densities of heavy liquids. As a result of these tests, it was shown that 60 % of the material should be discarded as tailings with 0.1 % Cu content. By considering float and sink test results, the following experiments were performed by using heavy medium cyclone and jigs.As a result of heavy medium cyclone tests, which are conducted on the sample in size range of –9+1 mm, 57 % of the feed material was discarded as tailing with 0.08 % Cu content and 7 % Cu loss, while a concentrate containing 1.43 % Cu was produced with 93 % efficiency (Table 1). Jig tests were done with the samples in the size range. As a result of jig tests with –9+1 mm size group sample, approximately 46 % of feed material was discarded as tailings with 0.13 % Cu content and 10.6 % Cu loss, while a concentrate with 0.94 % Cu content was obtained (Table 2)."

Jan 1, 2003

By Ming’an Wei, Chuanyao Sun, Yangge Zhu, Fayu He, Yanbo Shang, Xingrong Zhang

In order to discuss the separation mechanism of copper-molybdenum ore, surface electronic structures of chalcopyrite and molybdenite were studied in the paper, by using First Principles method of quantum chemistry. So, the separation mechanism of thioglycolic acid (TGA) with chalcopyrite and molybdenite was revealed better. The results showed that differences of the electronic structure of chalcopyrite and molybdenite could directly affect their interactions with TGA, such as band structure, density of states, Mulliken populations, and so on. And the frontier orbitals of chalcopyrite and molybdenite were also calculated by Dmol3 after the optimization by CASTEP, from which the interaction energies between minerals and TGA were obtained and compared. So, the essence of flotation separation of copper and molybdenum were well revealed.

Jan 1, 2014

By H. Wotruba, L. Gronen, A. Hellmann, S. Sindern, J. Katzmarzyk

"This paper focuses on the beneficiation of the REE-Y-Nb-Zr complex ore from the ‘Khalzan Buregtei’ deposit, Mongolia. Pre-concentration based on mineralogical studies was investigated at the Unit of Mineral Processing (AMR) and the Institute of Applied Mineralogy and Economic Geology of RWTH Aachen University. In order to minimize the energy consumption in the most energy intensive grinding process a pre-concentration process using dry magnetic separation of particle sizes coarser than required for the liberation of the valuable ore minerals was designed. Dry magnetic separation in the particle size range of 63-250 µm is suitable as the pre-concentration method, due to the intergrowth of REE-Y-Nb-Zr bearing minerals with magnetic minerals determined by QEMSCAN© analysis. The results showed that a mass reduction of 45.3 wt.-% at high recoveries of REE, Y, Nb and Zr (90 wt.-% and higher) in the pre-concentration product was achieved at the beginning of the process chain. The improvement of process efficiency as shown in this study depends on the abundance and association of minerals affecting the magnetic properties (e.g. hematite) of the ores. Therefore, these mineralogical parameters are as important as grain size and ore grade for the geometallurgical evaluation of potential mining operations at ‘Khalzan Buregtei’.INTRODUCTION Polymetallic deposits containing other critical elements besides REE have the advantage of being robust to economic development and fluctuations of individual metal prices. (Gronen et al., 2016). These deposits can host economic grades of heavy and light REE, Y, Nb, Ta, Zr in complex mineralogical compositions. About 120 deposits of this type are known worldwide, including ‘Norra Kärr’ in Sweden, ‘Strange Lake’ in Canada and ‘Khalzan Buregtei’ in Mongolia which are not valued economically yet. (Salvi. & Williams-Jones, 2004.)"

Jan 1, 2018

By Peter Ay, Matthias Schmidt, Christian Stollberg

"The aim of the study is the development of a seamless reprocessing procedure for plastics from automotive parts which are to be recycled (figure 1). Before automatic sorting can be performed, the materials first have to be identified by a near and middle infrared (NIR/MIR) system.Materials reprocessing basically includes research on size reduction, decoating, and roughening of the materials. Variants of the necessary technologies such as different shredders and mills and physico-chemical or mechanical decoating and roughening procedures together with the fundamental approaches underlying these methods are investigated and benchmarked. This allows the theoretical determination of the impact of each method not only on the overall process but also on the result achieved within the identification and sorting procedures."

Jan 1, 2003

By A. A. Sirkeci

In the scope of this investigation comparison between impact breakage and compression breakage were carried out for the separation efficiency of minerals using a chromite ore sample. The ore sample was broken below 1 mm employing a laboratory type roll crusher and an impact crusher. Concentration tests were conducted on -1+0.5 mm, -0.5+0.2 mm and -0.2 mm size fractions using a Wilfley type shaking table. Test results showed a remarkable difference between two types of breakage. Both concentrate grade and recovery was in the favour of impact crushing. Furthermore, the shape of the broken particles also showed differences such that in the case of impact breakage they were more spherical compared to compressive crushing. The results of the shaking table con-centration tests showed that a concentrate assaying 48.4% Cr2O3 were obtained with 78.5% recovery in the case of impact breakage. On the other hand the concentrate grade and recovery values were 48.8% Cr2O3and 52.4% respectively in the case of compression crushing. The losses in the tailings were also in favour of impact breakage proving that differential breakage occurred between chromite and gangue minerals.

Jan 1, 2014

By X. Y. Zeng

Most Chinese titanium bearing minerals are the composition of magnetite vanadium and ilmenite. All of such mineral processing plants use low intensity magnetic separators to recover magnetite and vanadium goes with magnetite. In the past years most of the plant tails containing about 10% TiO2 were abandoned. Now many of these plants use SLon magnetic separators to recover ilmenite in the roughing stage, which can throw away most of the gangs and slimes with very low cost. The new development of applications of SLon magnetic separators in Chinese ilmenite processing industry is introduced in the paper.

Jan 1, 2014

By Aubrey Mainza, Malcolm S. Powell

"A hydrocyclone with two vortex finders, named the three-product cyclone (3PC), has been successfully tested in the Platinum industry for dealing with the dense Chromite found in UG2 ores. This dense component preferentially reports to the cyclone underflow, resulting in an over-ground fine Chromite component in the final product. The dense media effect caused by a high concentration of this in the cyclone feed produces a coarsening of the cyclone overflow, which results in loss of recovery through over-size silica in the PGM carrying component material in the float feed. The fine barren particles of Chromite that report to the overflow are recovered through entrainment in the flotation process, resulting in detrimental contamination of the slag produced from the concentrate.Data from many industrial scale tests of the 3PC have shown that three distinct products are obtained when the inner vortex finder length (LIVF) is extended to the region either above (normal classification) or below (reverse classification) the transition zone (a region were the inner and outer overflow streams are identical). Due to wear problems arising from extending the IVF deep into the cone of the cyclone, it is advantageous to use the shorter IVF. Only the normal classification results are reported here, but similar outcomes (to opposite overflow streams) were obtained for the reverse classification. The results showed notable differences in the percentage split of the plus 100µm material in the product streams, confirming that three distinct products are discharged from the 3PC. About 12% of the plus 100µm material in the feed reports to the middlings stream, 1% reports to the final product, and the remainder to the cyclone underflow.Results of silica and chrome splits to the three distinct products namely, the inner overflow (INO), the outer overflow (OUO) and the underflow (U/F) are given in Table 1. These show that the 3PC can be used to recover coarse silica through screening the middlings product - which has a high silica content. When the vortex finder ratios (ratio’s of cross-sectional areas) are carefully selected, the split of plus 100µm silica to the middlings product ranged from 2.9 to 9.6%. Large amounts of oversize silica and chrome report to cyclone underflow, explaining their high percentages in the underflow stream."

Jan 1, 2003