Search Documents

By V. Ross

"The Upper Group 2 (UG2) reef in the Bushveld Complex in South Africa hosts an estimated 40% of the world’s Platinum Group Metal (PGM) resources. The processing of this ore via flotation poses two particular challenges: limiting the levels of chromite in the concentrate to reduce downstream smelting problems, and enhancing the recovery of ultrafine (typically -10 micron), liberated PGMs. Conventional ways of suppressing the entrained chromite, such as froth washing, is not effective in PGM operations, which are dominated by mechanical cells. The recovery of fine particles is hampered by low collision efficiencies with air bubbles, as well as oxidised surface layers especially in tailings operations. This paper documents the results of laboratory tests on a run-of-mine PGM UG2 ore, investigating the application of a pneumo-mechanical column (PMC) and its effect on PGM flotation and its selectivity with regard to chromite. A key feature of the device is the stage-wise release of aerated slurry from an agitated downcomer, thus creating conditions where the superficial velocity profiles of air and slurry change axially within the separation zone. This aids segregation of the silicates and chromite-rich fractions in the separation zone, concentrating the latter towards the bottom of the column and minimising its entrainment into the concentrate. Comparison of the performance of the PMC to that of mechanical laboratory cells under equivalent operating conditions showed improved PGM flotation kinetics and recovery. This was accompanied by a decrease in gangue recovery compared to the mechanical cells by more than 40%, thus doubling the final rougher concentrate grade from 50 to 100 g/t. Significantly, whilst the overall Cr2O3 recovery was reduced by more than 60%, the selectivity (PGM recovery vs Cr2O3 grade in the concentrate) was doubled.INTRODUCTIONThe Bushveld complex in the northern part of South Africa hosts the world’s largest reserves of Platinum Group Metals (PGMs), representing approximately 40% of the total PGE. It is characterised by three main PGM bearing reefs, namely Merensky, Upper Group 2 (UG2) and the Platreef. The Merensky and Platreef are dominated by silicates in the form of pyroxenites, and carry economically recoverable amounts of copper and nickel, in the form of chalcopyrite and pentlandite. The UG2 on the other hand is a chromitite ore with chromite as (ideally, FeO.Cr2O3) the most abundant gangue, often constituting more than 70% by mass with a PGM grade of around 4.5 g/t. Other key gangue minerals are pyroxene, feldspar and talc. The PGEs occur in a wide variety of minerals, with platinum and palladium sulphides typically accounting for about half of the total. Base metal sulphides such as chalcopyrite, pentlandite and pyrrhotite occur in only very minor amounts, accounting mostly for less than 0.1% by mass."

Jan 1, 2018

By V. Hema

Granular materials are widely used in process industries, such as chemical, pharmaceutical, cement, food, detergents, and fertilizers. Mixing, blending, calcining, reduction, heating, and granulation of these materials are frequently carried out in rotating cylinders. In all of these processes, the mixing and segregation of these granular materials is important as this controls the secondary phenomena in the rotating kiln such as heat transfer to the material. A significant amount of work is available in the literature but to date these efforts have not been able to capture the important parameters affecting the mixing and segregation in rotating kilns. In addition, the range of parameter values studied so far is rather limited. Simulations of granular materials are based on either discrete elements or continuum models. The discrete element methods (DEM) combine semi-empirical models for the inter particle interactions with the equations of motion from classical mechanics to simulate the explicit paths of all granules in a rotary kiln, thus yielding realistic predictions of the mixing process. This approach is very demanding computationally, which strongly limits the number of granules and the number of revolutions in a simulation. Continuum models dispense with the discrete particles and can therefore be scaled up more easily. But the constitutive relations that serve as the foundation for continuum modeling are difficult to come by, and often only applicable to specific systems and conditions. Here we have chosen DEM simulation for investigating the mixing and segregation behavior of granular materials in a rotating cylinder. This work is directed towards demonstrating the capability of the prediction of the mixing and segregation behavior of granular materials in a horizontal rotating cylinder through discrete element simulation. Further the effect of particle size and rotational velocity on the mixing and segregation behavior is investigated. The simulation results are quantified in terms of mixing index, mixing rate, segregation index and percolation index. Keywords: DEM simulation, granular mixing

Sep 1, 2012

By Carina Ulsen

The existing construction and demolition (C and D) waste recycling technologies and standards have been essentially focused on the production and use of coarse recycled aggregates. Very few papers focus on the production of recycled sand, although some previous results show that fine aggregates fraction represents around 40 to 60% (in mass) of the Brazilian waste and it is usually used as road sub-base or disposed in landfills. The quality of the recycled aggregate is strictly related to the content of porous and low strength phases, mainly the patches of cement remaining on recycled aggregate surface. Some technologies have already been described in the literature, even though, to the moment none of these technologies has clearly succeeded in reaching the large market available. This paper presents a summary of the main properties of the sand produced from C and D waste by tertiary crushing at vertical shaft impact crusher (VSI). Additionally mineral processing technologies were applied on the attained product, such as gravity concentration by shaking table and spirals and removal of cement paste by attrition. The main properties of recycled sand are discussed and compared to the previous C and D waste, respectively: particle size distribution, particle shape, chemical composition, cement paste content and porosity. The results demonstrates that the crushing allowed producing a VSI-sand with low porosity and water absorption due to the increasing on the content of silicates from natural rock phases and increasing liberation between these phases and porous cement paste; the particles from the attained product presented also a better shape (sphericity and aspect ratio). The attrition tests assayed on VSI recycled fine aggregates accomplished a further selective disaggregation of cement paste and other porous materials - the porosity was reduced from 10% to 7%. The concentration by shaking table at narrow sieve fractions led to a product with low porosity and reduced content of cement paste, however, concentration on spirals did not succeed since separation was performed essentially by the size of the particles. The heavy product from shaking table represented almost 75% in weight and has less than 60% recovery of CaO+LOI, and expressive reduction on porosity. The aim of producing sand from construction and demolition waste through mineral processing unit operations changes the recycling approach and contributes for up cycling the recycled sand. The exhaustion of sand deposits on Brazilian large centers, the increasing price and the construction boom encourages the development of alternative materials as construction raw material. Keywords: recycled sand, construction and demolition waste, technological characterization

Sep 1, 2012

By H. R. Manouchehri

"In all electrical beneficiation methods, the difference in electro-physical properties of the contributed mineral particles, essentially frictional charge, electrical conductivity and dielectric constant properties are exploited to achieve separation. The composition of the raw material determines what kind of either corona charging, conductive induction, or triboelectric separation method should be employed. The process is versatile and is influenced by different parameters related to mineral characteristics, surrounding ambient conditions and electrical and mechanical attributions of the separating device. Electrical separation is surface based beneficiation method which is mainly affected by the surface and surface changes of the minerals. Therefore, it is essential to understand how the electrophysical properties of the minerals can be changed/modified. During electrical/electrostatic separation process, both charge magnitude and its polarity that developed on the particles and therefore, their electrical beneficiation potential is essentially defined by surface phenomena. Therefore, it is essential to understand how the main electro-physical parameters can be changed/modified with applied surface treatment/pretreatment methods to promote separation. Surface treatment of minerals is carried out by different means, including chemical conditioning, irradiation, thermal treatment, etc. This paper discusses and analyze the electrical separation process, electrophysical properties of the minerals with special focus on the effect of surface pretreatment/treatment methods to affect electrical beneficiation potential of the minerals. The surface treatment methods vary in a wide range from simple surface cleaning to more complicated chemical conditioning and doping. The knowledge of the solid-state physics and chemistry leads to improve the beneficiation potential of different mineral systems by choosing suitable treatment method(s). Despite the complexity and multiplicity of the charging mechanisms, difficulties in separating fines it seems to be beneficial make our attempts to further investigate and develop the process as dry, low cost beneficiation process, especially nowadays when environmental concerns, as well as energy and water consumptions are main concerns for mining industry."

Jan 1, 2018

By F. Concha

A robust theory of sedimentation-consolidation evolved and was accepted by researchers world-wide in the last two decades of the 20th century. This theory provides a reliable method of thickener design and simulation. However, a process model, simple or sophisticated, empirical or phenomenological, is useful only if it is possible to determine, in an objective way, its experimental parameters. Research workers at the University of Concepción, together with Cettem Mineral Technology Center, created an integrated system of thickener design, simulation and control, including instrumentation, algorithm and software, which can be used by personnel in industry without specialized knowledge of thickening theory. In the paper, the development of three instruments for the measurement of pulp concentration, solid flux density and sediment compressibility is described. Each instrument uses software for data input, parameter calculation and results display. The paper also describes software for the optimization of the experimental parameter and for the design and simulation of industrial thickeners. Finally, mathematical algorithm and control strategies based on the phenomenological model are presented and compared with classical feedback control.

Jan 1, 2014

By Egbert Burchardt

"Some of the challenges faced by the mineral industry in the future are the need to process low grade ores at the lowest operating cost, to deal with elevated energy cost and to address scarce water resources in some regions of the world. These challenges will increase the demand to develop highly energy-efficient and less water-consuming mineral processing systems. Experience from other industries suggests that HPGRs could help to achieve these goals, due to their high energy efficiency and their ability to be used as dry grinding systems. Historically, HPGRs have been used mainly as tertiary crushers in mineral applications for the production of ball mill feed. In the cement industry, however, HPGR systems have been successfully applied for grinding limestone, clinker and slag to a final product fineness (p80) of between 30 and 90 µm without the need of downstream ball milling. The total energy consumption of HPGR finish grinding systems in the cement industry has been found to be 30 to 50 % lower than in ball mill systems. This leads to the question of whether the same methodology can be adopted in the mineral industry. Such a step would require the use of dry rather than wet grinding systems. Traditionally, dry grinding systems have been only an exception in mineral processing, since most post grinding processes are wet. However, there are successful - mainly ball mill based - dry grinding examples in gold, nickel or iron ore. Experience from some of these dry grinding references are summarized in this paper. In addition, this paper explores two future-orientated questions: What opportunities does HPGR finish grinding offer the mineral industry? What are general conditions and challenges for adopting this technology for mineral applications?"

Jan 1, 2014

By H. U. R. Kattentidt, W. L. Dalmijn, T. P. R. de Jong

"Research at Delft University aims to develop systems for automatic inspection and sorting of bulk solids which can be applied in the mineral processing and recycling industry. A recent development includes an automatic sorter based on airport X-ray inspection technology. It is designed for continuous inspection and sorting of 5 - 150 mm solids and has as objective a cost effective and high capacity on-line inspection and sorting.Dual energy X-ray transmission imaging provides instantaneous data about particle dimensions and the atomic number distribution. The system provides particle thickness and average atomic number on a pixel level at scanning speeds between 250 and 500 lines / second. With existing X-ray components inspection speeds between 0.5 and 2 m/s at approximately 1-meter inspection width and between 1.5*1.5 and 5*5 mm2 sensor resolution can be achieved.Imaging algorithms that were developed by Delft University for applications in recycling, waste cleaning and other applications acquire shape, size distribution and composition data. Currently on-line processing of a product at a rate of around 200 particles per second is possible using a standard PC. Experiments with a demonstration X-ray unit indicated good potential for various applications in solids processing. They include continuous inspection of organic content, sulphur, chlorine, ash, and metal distribution. It is applicable for coal cleaning, ore sorting, industrial minerals, and various applications within waste cleaning and recycling. Dual energy X-ray transmission fundamentals and recent progress in system development and applications are presented."

Jan 1, 2003

By J. J. Liu

In the Bayer process, control of alumina trihydrate particle size, oxalate stability and morphology and foaming is crucial for improving the yield and quality of alumina trihydrate. One way to economically achieve such control is to employ specifically developed chemical additives, termed, crystal growth modifiers (CGM?s). In this paper, the mechanism of action and practical application of CGM?s in the Bayer process are summarized. The application of CGM additives allows for both enhanced agglomeration and secondary nucleation control, and hence coarsening of the particles. Current research efforts have utilized the information gained from mechanistic studies to enhance the performance of CGM products. It was demonstrated in both laboratory tests and industrial operations that the newly developed CGM formulations have a range of properties with enhanced performance, compared to the current commercial products.

Jan 1, 2014

By Fedotov Pavel

One of the efficient means of ore disintegration during the processing is its volume breakage in such machines as roller-presses. Up to date neither the ore disintegration mechanism in roller-presses nor the reasons of their high efficiency are thoroughly investigated. In this work, the mathematical model of Finite Element Method of bad material disintegration in roller-press is discussed. The mechanism of the interparticle ore disintegration is traced.

Sep 1, 2012

The ball level and pulp load play a key role in the operation of industrial scale ball mills. These two operating variables have a significant influence on the performance of the ball mill and any attempts to optimize these devices require manipulating either one or both of these variables. There are several models that can be employed to perform simulations to optimize the performance of industrial ball mills. However, most of these models require ball load and pulp load measurements as inputs to calibrate the model. The changes suggested by the simulator also provide operating regimes that involve moving either the ball level or pulp load and sometimes both of these variables. A ball mill model coded in JKSimMet was used in conjunction with the Sensomag to optimize the secondary ball mill at Waterval concentrator in South Africa. The results show that the perfect mixing ball mill model can be used in conjunction with the Sensomag to optimize the performance of the secondary ball mill.

Sep 1, 2012

By Graeme Lamson, Rene Dobbe, Merle Kalstrom, Janice Baron, Robert Thorpe, Chris Martin, Snezana Bajic, Amanda Palko

"This paper presents early results from a case study at the Mount Polley porphyry copper mine in British Columbia, Canada. Daily mineralogical data was acquired and reconciled with daily plant assay and recovery balances to interrogate the mineralogical controls on plant performance. After commissioning, the Minesite machine operated smoothly and reliably, creating daily data to generate mineralogical balances around the circuit for a period of several weeks. The key data, on final products were produced within 13 hours of the end of the respective operating period. The resulting information allowed for a greater understanding of the opportunities and limitations of the Mount Polley metallurgy. In this paper, how this information can be used to help long term strategic planning for the operation, as well as mine planning and production forecasting and the fine tuning of day to day mill operations is described. Early data available at the time of preparing this paper indicated that roughly 40% of the sulphide losses, or 32% of total copper losses existed as low grade inclusions in +75 micron tails. This represented the dominant form of long term copper losses, demonstrated repeatedly in the routine analytical data. However, on a day-to-day basis, the amount of copper present as chrysocolla is the major driver behind variations in total copper recovery. The degree to which this influences mill recovery is valuable to the geologist or mine planner. As they are armed with mineral speciation information for future ores, this will allow for improved mine planning, prediction of copper recoveries and production forecasting. The data was also started to find value in the mill by showing what caused sulphide losses. In the roughers, for example, the data showed poor recovery was the result of poor flotation performance and not any changes the speciation of copper sulphides or their liberation characteristics."

Jan 1, 2014

By Chen Jianhua, Shen Zhenchang, Zhang Ming, Chen Feifei

"With flotation cells scale-up, the performance of flotation cells is increasingly variated for short-coming and dead zones existing. The residence time distribution which shows the movement of tracers can assess the unexpected flows such as short circuit and dead zone in a flotation cell. In this paper, the residence time distribution of pilot flotation cell is investigated with CFD simulation. Based on the theoretical model, the short-coming probability and dead zone probability are quantitative. The ideal average residence time is similar with the actual average residence time. The mixing effect of the flotation cell approaches the ideal continuous stirred tank reactor. The operating parameters such as speed and feed velocity have complicated influence on residence time distribution. The research would be helpful to understanding flow in flotation cell and improving performances of flotation cell.INTRODUCTION Froth flotation is a method which purifies minerals according to difference of physical and chemical surface characters of different mineral particles (Shen, Z., Chen J, 2012). Flotation cell is a key equipment for froth flotation method. The flotation cell performances have great influences on flotation index.It is difficult to evaluate flotation cell how to improve flotation procedure to complexity. The main flotation cell performances are aeration volume, air dispersion, solid suspension and residence time distribution, etc (Shen, Z., Lu, S., 2008). Residence time distribution is an important fluid hydrodynamics which could reveal the flow of pulp, mixing of particles and air bubbles. In the flotation cell, the ideal average residence time of pulp could obtain easily. But the fluid differential units would be different flow paths. The residence time of the fluid differential units is variation and would be longer or less than the average residence time. The residence time distribution would reveal the mixing effect and predict the not ideal flow in the flotation cell such as shorting cutting, dead zone, etc. As we know, the shorting cutting and dead zone would be decreased the real flotation time and it is disadvantage to better flotation effect, especially for large flotation cell. It is impossible to eliminate the not ideal flow totally. It is very important to reveal and decrease the shorting cutting and dead zone probability in the flotation cell."

Jan 1, 2018

By M. Surracco, M. C. Tilocca

"Mineral comminution is often a costly process which also requires high level of energy. In the course of the studies carried out by the researchers of the Department of Civil-Environmental Engineering and Architecture at the University of Cagliari, aiming at the optimization of the reduction processes, it has been experimented, among of others, the effects of high-speed water jets on minerals grinding. As far as coal is concerned, some of the solutions initially adopted are presented in this paper, which essentially relied on the water jet power only, with secondary use of mechanical actions, to reach the most modern solutions that envisage the use of mechanical energy, normally used in traditional grinding machines, in synergy with hydraulic energy transferred by water jet.INTRODUCTION Mineral comminution can be rather expensive and demand a high-energy consumption, especially for fine sizes (Austin, 1979). Further interesting perspectives in this area may be offered by comminution means aided by high pressure water jets (Ciccu 2007), whose crushing potential is currently used for several operations such as cutting different materials, rock digging and industrial cleaning. The crushing action of water jets may induce a traction stress in materials where substances of a mineral nature, especially if characterised by permeable porosity, oppose a minor resistance (Griffith, 1920). The first solutions to this purpose essentially relied on the sole energy of water jets, with a secondary use of mechanical actions (Ciccu, 1993). Results were encouraging, despite the high values of specific energy for the low capacity of treatment. However, due to the difficulty in making the techniques mainly based on hydraulic energy practically applicable to solids comminution a solution was experimented, with some interesting results, consisting in the combination of mechanical energy, normally used in traditional grinding devices, with hydraulic energy transferred through water jets, in a synergic relationship (Ciccu, 1998; Tilocca, 2016)."

Jan 1, 2018

By S. J. Dai

The cadmium and cyanide are main poisonous components in cyanide electroplating cadmium waste water of an electroplating plant in Shenyang. The content of cadmium is about 26 mg/L and the content of cyanide is about 11.782 mg/L in this waste water. The main form of cadmium and cyanide are ions which are Cd2+and CN?. Because the cadmium and cyanide exceeded the standard seriously, the waste water must be disposed before it discharges. The microbiological method of treating heavy metals in wastewater has many advantages. For example, it has a fast adsorption velocity, high processing efficiency, wide range of pH and temperature, few invest, low running cost, no the second pollution and so on. At the same time, the CN? could be degradated by some microbiology. The physical nature, the chemical nature of Bacillus mucilaginosus, the adsorbing condition and adsorbing regular of Bacillus mucilaginosus to cadmium in the wastewater are studied by using Bacillus mucilaginosus as adsorbent removing cadmium from electroplating wastewater. The experimental results show that the adsorbing rate of cadmium is over 92%, under the room temperature(about 25?), stiring revolution in adsorption being 800 r/min for 30 min, pH being 5 , the bacteria being cultured after 5d with the biomass of Bacillus mucilaginosus 40g/L (wet weight). The mechanism in biosorption process of Bacillus mucilaginosus to cadmium is analyzed and discussed by TEM , Zeta potential,and infrared spectroscopy analysis. The results showed, the chemical involving is main adsorbing form, while electrostatic attraction, ions exchange, hydrogen bonding and Van Der Waals force are concerned cooperatively. ?NH2 ?, ?C=O?, ?C=O?NH?CH2, ?CH3, ?OH are main adsorbing groups. At the same time, the floatablity of removing cyanide by Bacillus mucilaginosus is explored.

Jan 1, 2014

By B. P. von der Heyden, P. Neethling, M. Tadieb, L. Babedi

The effects of trace element substitutions in sphalerite mineral structure on optimised floatation response have, as yet, not been fully constrained or fully understood. To further this important field of study, this contribution focusses specifically on mineral and surface chemistry, and electro-chemistry of Cd- and Co- substituted synthetic sphalerites using Raman spectroscopy and Zeta potential experimentation. Raman spectroscopy illustrates that the presence of these impurities results in the introduction of a new mode, the relative intensity of which can be correlated (Cd r2=0.95 and Co r2= 0.99) to the dopant concentration. Comparison to X-ray Diffraction results measuring the unit cell parameter further shows that this relative intensity (Cd r2=0.81 and Co r2= 0.99) may provide insights into the degree of lattice strain within the mineral structure. The zeta potential distribution of an un-activated Cd-sphalerite show no detrimental effect as function of Cd content. Although the iso-electric point shifted from 2.45 at 1 wt.% Cd to 2.69 at 3.68 wt.% Cd, the zeta potential remained negative at alkaline media. Conversely, cobalt at low concentration of 0.36 wt.% had a detrimental effect on the surface charge, resulting to a close to neutral zeta potential at different pH. The adsorption of Cu ions on the surface of Co-bearing sphalerite conditioned in an alkaline media slightly increases the zeta potential of Co-sphalerite. While the Cd-bearing sphalerite decrease in negative zeta potential at >1 wt.% Cd indicating a complete exchange between Cu and Zn. The results presented herein illustrate that, based on the chemical nature of the substituting metal; sphalerite will exhibit multiple response to flotation reagents. Maximum recovery of zinc can thus only be achieved through multidisciplinary study and fundamental understanding of the effects of cation substitution on mineral structure and surface chemistry, the latter necessarily affecting the floatation response.

Jan 1, 2018

By K. Saberyan

In this study, solvent extraction of zirconium by using triphenylphosphine oxide as extractant has been investigated. The results showed that extraction of zirconium by triphenylphosphine oxides in nitric acid and hydrochloric acid media were negligible. Extraction of zirconium in acetic acid media with concentration of 0.01~0.2 M has been studied and the results showed that the maximum percent of zirconium extraction was 40% in acid acetic with concentration of 0.01 M. By addition complexing agents such as potassium thiocyanate with the concentration of 0.01~0.2 M zirconium extraction increased up to 86% in 0.2 M potassium thiocyanate. By addition of sodium salicylate with concentration of 0.01 M and in pH=2.5, the maximum extraction of 96% was achieved. The striping of zirconium from organic phase can be carried out by 0.5 M solution of sulfuric acid.

Jan 1, 2014

By Ari Kokko

Metso has a long history supplying boilers for high ash coal firing. These boilers are based on circulating fluidized bed (CFB) technology. CFB?s biggest benefit is fuel flexibility ? it can burn fuels from high moisture content to high ash content. Metso has delivered tens of CFB boilers burning waste or high ash coal starting on 80?s. Some of the boilers have been in operation twenty years meaning that there is a long term experience from these plants available. This feedback includes boiler performance and maintenance issues of the boiler. Metso is also delivering coal washing plants to improve coal quality, i.e. reducing ash content of the coal. The idea to combine coal washing plant and CFB boiler was made up two years ago in Metso. Up-coming legislation of coal washing and restrictions for washery reject land-filling in India are good drivers for this kind of concept. Pre-study of this kind of concept led to the conclusion that coal washing process can be fine-tuned so that reject?s calorific value is only 1100 kcal/kg and that was set as a target for boiler design. Metso shipped 200 tons of washery reject to its own research center located in Tampere Finland. First a wide range of fuel characterization tests were done in lab-scale and after that one week test run in 4 MW CFB pilot boiler was done. Test run proved that 1100 kcal/kg can be fired without any support fuel with special boiler design. Test run results gave a good set of data regarding combustion efficiency, emission performance and boiler dynamic behaviour when burning this kind of fuel. These results are introduced in this paper. This paper introduces also the CFB boiler concept for washery reject firing including boiler plant, fuel and ash handling systems and flue gas cleaning system. Power plant can be integrated with coal washing plant so that boiler size matches with washing plants c

Sep 1, 2012

By Jorge Misle, Daniel Silva

"This paper addresses the need for advanced control technologies and strategies in the mining industry, its potential and actual impact on mining processes and the best practices for their implementation, operation, and long term sustainability. It is well known that advanced process control (APC) can be a very good source for incremental process improvement for the mining industry, yielding to higher production rates or helping maintain consistent production rates despite ore changes. The application and integration of new technology, process knowledge and innovation are key elements in building such a supporting structure. More specifically, and this cannot be emphasized enough, the correct application and assembly of control tools, the in-time presentation of key data to decision makers and the development of relevant statistics and KPI’s (key performance indicators) can and will make a difference not only in terms of production, but also in plant stability, availability and production costs. In deploying such ideas and aiming at the long-term goal of "Operational Excellence", Minera Los Pelambres (MLP) has developed a number of successful control strategies, best practices and technologies, which are not only the application of state-of-the-art automation and computing tools, but rather the assembly of the above presented structuring factors. This work discusses some of the key tools and ideas implemented for SAG & Ball milling and Flotation areas, their performance results and the roadmap taken for the integration of process knowledge and control tools. Also, cases studies are presented and discussed further to not only show the main areas of improvement, but also to highlight the benefits of such strategy that for the most part, deviate from the traditional mining industry control approach. Also, a word is given on the need for innovating in the design of control strategies and leveraging best practices and process knowledge that ultimately, will contribute to long-term reliable operations, improved mineral processing and, although unmeasured, lead to a superior overall performance and productivity of all mining personnel involved."

Jan 1, 2014

By Gurubasayya Swamy

This paper presents the consequences of modernization and expansion of process plant by implementing SAG and Ball Mill and Carbon-in-pulp technology at the Hutti Gold Mine. From the inception of the process plant, it has undergone many changes for the improvement. In the beginning, only gravity recovery of gold was carried out by using Pebble Mills and Strake Tables. Later amalgamation, Cyanidation and Zinc precipitation and finally Carbon-in-pulp gold recovery system was implemented. Grinding plant was modernized by implementing SAG and Ball Mill and Knelson concentrator for free gold recovery as a result, the production rate, rate of recovery, reduced man power, Modernization and expansion of process plant has also yielded in safe and smooth running of the plant. Keywords: sag and ball mill, cip, modernization and expansion, productivity, gold recovery

Sep 1, 2012

By A. T. Adema

The cohesive zone, where the ore fed into the blast furnace softens and melts, is critical to the blast furnace performance and stability due to its influence on the gas and solid flow. This paper de-scribes a project for the development of a process model to predict the cohesive zone properties and the results of its first step; the solid flow model. The process model is expected to describe a realistic solid burden flow and the formation of the cohesive zone, its shape, location, structure, permeability, and in particular the mineralogical changes within the cohesive zone. This will be achieved using various simulation and computing tools: a combination of the Discrete Element Method (DEM) and Computational Fluid Dynamics (CFD), the DEM?CFD hybrid approach, together with models for the thermodynamics and reaction kinetics. The key benefits of the hybrid approach lie in the coupling of the continuous phase and the discrete particles, and the possibility of introducing thermodynamics and reaction kinetics into the system in a more realistic manner. Two DEM simulations are presented for a small scale blast furnace to investigate the influence of non-spherical particles on the solid flow. This influence can be observed from a more even solid flow pattern and a reduced deadman size. The results indicate the requirement to include non- spherical particles in a blast furnace simulation to achieve a realistic solid flow.

Jan 1, 2014