Search Documents

By H. J. Cao

Valuable elements could be extracted by microorganism ferment fluid from bauxite, which mainly due to bacteria acid namely organic acid. And after leaching, reclaiming the remainder organic acid in leaching solution was an important procedure for bauxite leaching process. the re-searching status about organic acid reclaiming process from bauxite ore bioleaching solution was summarized. Common processes for recycling organic acid from bauxite bioleaching solution in this period and their advantages and disadvantages, research aspects which need being confirmed for the future were Indicated

Jan 1, 2014

By F. Karakas

In this investigation, one of the most energy consuming stage of the cement manufacturing process, grinding stage, was studied. The aim of the study is to reduce the energy consumption. Optimum operating parameters were determined. Experimental studies were performed at three differ-ent stages. Grinding of limestone, clay and marl which are the main components of the cement, to approximately below 90 microns, was the first stage of the cement grinding. At this stage, effect of feed size and ball charge were investigated. At the second stage, the Bond work index of clinker and additives (slag, trass, limestone and gypsum) was found separately. After forming composite cement with clinker and additives, the Bond work index of this mixture was also determined, thus the results of separate grinding and grinding of mixture were compared. The Bond work index of mixture was found as 13.59 kWh/t, while the arithmetic mean of the Bond work index values of components was 14.90 kWh/t. Finally, clinker and additives (slag, trass, limestone and gypsum) were ground under the same conditions. At this stage, laboratory type of ball mill was used in order to understand grinding characteristics of the cement components. As a result of the experiments, it was found that energy consumption for the grinding will be lowered if the mills with 38 % ~ 40 % ball charge are used in the cement grinding. Moreover, grinding with mixture of clinker and additives gave better results than separate grinding of these components in terms of energy consumption.

Jan 1, 2014

By Choi Sang-Ken, Chung Hun-Saeng, Kim Byoung-Gon, Park Chong-Lyuck

Fine grinding of crystalline graphite was conducted using a dry attrition mill with a vacuum system to investigate the characteristics of size reduction. Low pressure and high temperature conditions in the grinding mill were found to greatly improve the efficiency of the size reduction of graphite. Natural flaky graphite of .100 mesh was ground into sub-micron sizes, then over 90% of the product were able to be reduced below 1?without disrupting their crystallinity in a short period of time. Reducing the atmospheric pressure in the grinding environment promotes the removal of chemical species such as oxygen and water molecules adsorbed on the graphite particle, resulting in effective size reduction while maintaining the crystallinity of graphite.

Jan 1, 2003

By Nina Panteleeva, Elena Afonina, Stanislav Titkov, Jury Buksha

"Flotation processing of water-soluble minerals (potassium ores, sedimentary salts of salt lakes) is currently the main method for production of potassium fertilizers and concentrated carnallite which is the initial product for production of metallic magnesium. Flotation of sylvite (KCl) and halite (NaCl) is carried out in the electrolyte solutions: KCl-NaCl-H2O and KCl-NaCl-MgCl2-H2O. The report presents the results of studies of the effect of concentration and the electrolyte type on the size of air bubbles in a flotation cell in comparison with the floatability of mineral constituents of potash ores. The floatability in electrolytes of various compositions has been studied: - of sylvite (KCl) by alkylamines, - of halite (NaCl) by alkylmorpholines, - of silicate-carbonate slimes contained in the ore by ethoxylated surfactants. The reagent modes (regimes) activating the flotation desliming of potash ores have been developed."

Jan 1, 2014

By Özcan Y. Gülsoy

Coal beneficiation with optical sorting has not yet been studied in detail. Optical separation of coal from gangue particles as a dry method can be used as an alternative to the other enrichment methods. Developments in optical and pneumatic technology put the optical sorting one step forward by means of applicability of the mechanical sorting to the mineral industry. Because of the inefficient separation performance, dry separation of coal is very limited in industrial applications. Therefore, optical sorting depending on color differences between two minerals can be introduced to coal beneficiation systems. In this study, coal samples obtained from Konya-Ilgin region (Central Anatolia-Turkey) were separated by optical sorter and the results were evaluated. The conventional floatability tests for Ilgin coal are conducted by collecting most of the feed material at 1.3-1.4 g/cm3 density range. Separation of Ilgin coals with heavy medium methods will not be possible because of poor density difference between coal and its impurities. There are important color differences among the floated particles at 1.3-1.4 g/cm3 density range. Therefore, Ilgin coal is subjected to optical sorting in a pilot scale optical sorter. Different size fractions were fed to the optical sorter and then rejected and accepted particles by equipment were analyzed. Ash content of the accepted particles was reduced to 25-35 % and ash in tail increases up to 55-60 % after sorting. Although most of the material floated at low densities, optical sorter separated the feed into two different quality products. This study has the potential to clarify applicability of optical sorting even to non-floatable coals and to provide an important contribution to both industrial applications and literature.

Sep 1, 2012

By X. M. Yu

A large amount of polluted sludge is produced by a nonferrous metal factory after treating waste water with lime/ferrous salt. The concentration of arsenic in the dried sludge is high to 5.84%, a toxicity test is taken on the sludge according to GB5085.3-2007 and the extraction content is 15.75mg/L, which surpasses the arsenic extraction standard [As]=5mg/L, the sludge is categorized as hazardous waste. If put outside without disposal, it would be very harmful to environments. Here we report an optimum protocol to extract arsenic; S2- alkaline liquor is utilized to treat the arsenic sludge. At 85?, 10L 7% S2- liquor is added into 1kg dried sludge and the resulting mixture is stirred for 120min at 250r/min, then separated by centrifugation and the compressed waste residue dried naturally. The average arsenic content is 1.40mg/L, lower than GB5085.3-2007 Standard and arsenic-free residue is consistent with GB18598-2001 Standard, which can be bury safely. The extracted arsenic is transferred into copper arsensite for use as addictive in copper electrolysis and the waste water can be recycle after calcium is removed.

Jan 1, 2014

By G. X. Du

Reaction kinetics of serpentine and hydrochloric acid is theoretical basis for optimizing reaction process conditions of serpentine and hydrochloric acid. Kinetics of serpentine and hydrochloric acid was studied in this paper. The results indicated that apparent reaction order to hydrochloric acid was two and reaction kinetic equation could be expressed as: 2HClHCl,ddtckct-=·. The diffusion rates of hydrogen ions in liquid film on surface of serpentine particle and in amorphous silica layer generated in the reaction and chemical reaction velocity during the reaction had important effects on to-tal reaction velocity. And chemical reaction velocity had the most significant influence. The relation of conversion rate of magnesia xMgO with reaction time could be expressed as: 1(1)xkt--=·.

Jan 1, 2014

By S. Gaydardzhiev

Laboratory batch tests having preliminary and orientation character aiming at improvement of the molybdenum flotation at Ellatzite copper processing plant in Bulgaria have been conducted. The following technological parameters have been screened to study their influence on the grade and recovery of copper and molybdenum during the rougher flotation stage: flotation pulp density, pH, addition of secondary collector and replacement of MIBC by pine oil as a frother. The results have shown that slightly better grade/recovery figures could be obtained for both copper and molybdenum at lower flotation pulp densities. The addition of kerosene has improved the recovery of molybdenum however, on the expense of that of copper. The effects from pH variation and the replacement of MIBC by pine oil as a frother have been almost negligible.

Sep 1, 2012

By F. Burat

The present research covers the results of experiments carried out with high frequency vibration screen on dewatering of coal fines. In the tests, the addition of surface active reagents was studied employing a high frequency vibrating screen. To increase the efficiency of mechanical dewatering processes, ultrasonic treatment was applied along with surfactants and optimum dewatering conditions were obtained. The moisture content of the feed material was from 82.5% to 41% by the optimization of operation parameters including the angle of the screen, vibration frequency, feed rate and screen opening size. Optimum parameters obtained in dewatering processes carried out with the vibrating screen were kept constant and the effects of surface active reagents and ultrasonic treatment on dewatering were investigated. Finally, the moisture level of the material was further reduced from 41.0% to 37.66%.

Sep 1, 2012

By C. Gomez, J. Finch, R. Dalhke, J. Torrealba-Vargas

The velocity of gas passing through a flotation cell can be estimated by collecting bubbles by natural buoyancy in a closed tube and measuring the rate of pressure increase. The governing equation is derived and verified. Single- and two-tube gas velocity sensors are described. The latter design permits a correction for bulk density and level change during signal collection.

Jan 1, 2003

By X. W. Lv

The intelligent recognizing and processing system for sinter ore mineragraphy make a great convenience of recognition and measurement. Specially, it?s critical important for a successful intelligent system to extract the minerals? feature accurately and sufficiently. Reflection index, as the crucial feature of mineral, is calculated by the theoretical calculating model of index based on the principle of imaging color models. In gray histogram of minerals? micrograph, the peaks? positions represent the information about mineral categories and contents. The relationships of different minerals? peak-positions in curve of gray histogram were got by using the peak-find model of gray histogram and calculating model of reflection index. These two models which can be regard as the method of feature extraction for minerals? photomicrograph also lay a good foundation for the artificial intelligent system of recognition and processing in sinter ore.

Jan 1, 2014

By Hajime Miki, Mutia Dewi Yuniati, Tsuyoshi Hirajima, Keiko Sasaki

Acid mine drainage is mainly due to pyrite/arsenopyrite oxidation processes, and suppressing such processes is important issue. As a promising process it is reported that silicate ion can complex with catechol (1,2-dihydroxybenzene) and this complex is oxidized to a solid silica layer on the surface of those sulphide minerals. Detailed behavior was investigated from the result of electrochemical experiments. Results of polarization potential showed that oxidation peak can be seen only in the presence of both silicate ion and catechol addition at this peak potential and this peak can be identified as silicate-catechol complex oxidation to silica. Potentiostatic experiments indicated the dissolution kinetics of pyrite. Untreated pyrite dissolution rates were higher than pyrite treated with catechol and silica solution. To enhance the silica layer reaction on pyrite, the pyrite potential was held at 550 mV vs. SHE in catechol silica solution. This pyrite dissolution kinetics was almost the same as untreated pyrite. Potential hold followed by drying for 30 min process resulted in much lower pyrite dissolution rates. Drying is important for development of the silica layer. Analysis of this potentiostatic curve provided a way to estimate the thickness of the produced silica layer and kinetic information of treated/untreated pyrite. Untreated pyrite showed thinner initial layer thickness on the surface of pyrite (oxidized passive layer, not silica) and higher oxidative kinetics of pyrite compared with silica-coated pyrite.

Jan 1, 2014

By J. Kwon, D. Lee, H. Cho

"The use of the combined grinding and liberation model to predict liberation characteristics of iron ore comminuted by a ball mill was studied. Comminution characteristics were obtained using the one-size fraction method. The iron ore samples were crushed and separated into a number of narrow size fractions by screening. The size fractions were further divided by magnetic separation into three classes: concentrate, middling, and tailings. Subsequently, various size-grade classes were subjected to ball milling, and the results were analyzed in terms of the kinetic grinding model. The mineralogical textures of the grinding products were analyzed using mineral liberation analysis. The distribution of iron content within the size fractions was characterized by the beta distribution combined with the Andrew–Mica diagram. It was found that the grinding characteristics of the iron ore samples varied slightly with the iron content. However, the liberation characteristics were well described by the same set of liberation model parameters, regardless of composition. The variation in grinding kinetics with composition and the liberation model parameters was used in the combined comminution–liberation model to predict the evolution of the size-composition matrix as grinding proceeded. The predicted results agreed well with the experimental results. The developed model can be used to construct the yield–recovery graph and to calculate the liberation efficiency to determine the size reduction threshold for efficient separation. INTRODUCTION In mineral processing, comminution is usually the first step that ores undergo to liberate valuable minerals from gangue minerals. Generally, as the particle size decreases, higher liberation can be achieved. However, excessively small particles are unfavorable to subsequent processes, such as separation. Moreover, comminution is a highly energy-consuming process itself that accounts for approximately 60% of all energy used for processing. Therefore, there is a definite need to increase energy efficiency by applying adequate stress so that a high degree of liberation can be acquired at the coarsest size without overgrinding. To this end, it is essential to develop a model to predict the liberation of minerals as a function of size reduction."

Jan 1, 2018

By Ming’an Wei, Chuanyao Sun, Zhenguo Song, Zengwen Dou, Yangge Zhu

"The effects of pH value and dissolved oxygen(DO) in the pulp to the Eh and flotation recovery of pyrite were investigated using potential online detection system. The effects of DO on the Eh and flotation recovery were tested which DO changed from 0.5mg/L to 19.5mg/L in six different pH buffer flotation systems (pH: 4.00, 5.62, 6.86, 9.18, 10.01 and 10.96 respectively). Results of potential detected online demonstrated that the pyrite electrode has nearly the same response to potential as with platinum electrode for the FeS2-xanthate-H2O flotation system under the study conditions. Pulp potential and recovery of pyrite were remarkably influenced by pH, both of them decreased with the increasing of pH and, especially, sharp decreased after pH above 9. As the concentration of DO was increased, the Eh was also increased in all the six different buffer solution, while the flotation recovery was decreased. And the amplitude of variation for Eh was not obvious in acidic and neutral solutions, but on the contrary, the change for flotation recovery was remarkable in neutral and alkaline conditions. This may indicate that the flotation of pyrite will be deteriorated in alkaline and high DO concentration conditions."

Jan 1, 2014

By S. Nitta

The present study deals with a new approach in calculating the size of Tower Mills. The method is derived from the application of grinding kinetics theory on the analysis of by-gone operational data. It requires only information on the capacity of the mill to be designed, the product fineness and the Bond?s work index to give an accurate and simple prediction of Tower Mill characteristics. An example illustrates the different steps of calculation.

Jan 1, 2014

By Yuexin Han, Jie Liu, Shuai Yuan, Yanjun Li

"In order to improve recovery efficiency of iron minerals from iron ore tailings and to reduce its connected environmental pollution, this article investigated the reducing roasting of iron ore tailing in a laboratory fluidized magnetization roasting reactor to optimize the roasting method and conditions. The examined parameters included roasting temperature, roasting time and reducing atmosphere. The parameters evaluating magnetizing roast efficiency and theoretical value were determined. X-ray diffraction (XRD) analysis was used to investigate the conversion of iron phase after roasting. The results show that the best magnetizing roast conditions are roasting temperature of 540?, holding time of 15min, and CO concentration of 20%. The magnetization conversion ratio of roasting products is over 80%, under the best magnetic separation condition, the concentrate grade of iron is 65.61 % and the recovery of iron is 83.77 %. The XRD analysis shows that Fe exists in hematite and siderite before roasting and exists in magnetite after roasting. The technique not only recovers the iron minerals from tailings with good economic benefit, but also reduces the environmental pollution of tailings accumulation.INTRODUCTION Iron ore tailings are the solid wastes generated during the beneficiation process of iron ore concentration and are one of the main pollution concerns in the mining industry (Das et al., 1996). Continuous development of the iron and steel industry has led to the increasing amount of iron ore tailings; there are over 300 million tons of iron ore tailings discharged per year (Rao et al., 2016). The huge amount of stockpiled iron ore tailings brings a series of environmental and social problems. Comprehensive utilization of iron ore tailings can not only reduce environmental load but also conserve resources, promoting sustainable development of the society. In recent years, iron ore tailings as secondary resources have received considerable attention in many countries in the word and numbers of studies on utilization of iron ore tailings were carried out, such as recycling the valuable minerals (Datta et al., 1996; Jia et al., 2013; Panda et al., 2018), used in construction material compositions as alternative source of raw materials (Das et al., 2012; Zhou et al., 2012; Luo et al., 2016) and other utilization. The iron minerals were recovery by magnetization roasting (Rao et al., 2016; Yang et al., 2013; Yang et al., 2011) and flotation (Kumar and Mandre, 2016). By comparison the reduction roasting has more advantages, but it was found that the conventional roasting equipment was inefficient, high energy consumption and un-economically applied on an industrial-scale."

Jan 1, 2018

By Pengbo Chu, James Finch

Bubbles around 1 mm diameter provide the high interfacial area for capture and transport of hydrophobic particles in flotation. The formation of such fine bubbles is commonly achieved by addition of frothers that appear to simultaneously retard coalescence and promote break-up. High inorganic salt content in process water can substitute for frother. In this work we focus on the action of salt (sodium chloride) on formation of bubbles by break-up. An experimental setup that isolates break-up from coalescence was employed. A pocket of air is exposed to controlled mechanical turbulence to produce single bubbles by the induced deformation of the air and the events imaged. The presence of salt is shown to produce smaller bubbles than in water alone. Comparison with a similar study on frothers is made. The argument is advanced that the presence of frother and salt creates surface tension gradients at the air/water interface which add to the mechanical energy of the deformation and break-up process.

Jan 1, 2014

By D. Gucbilmez

Three spiral concentrators having different geometries were compared in a chromite processing plant. They had different diameters, helix-cross sections and capacities. Two of the spiral concentrators were manufactured in China and one of them was manufactured in Australia. The tests were carried out in a closed circuit experimental setup by using a low grade chromite ore. The pulp densities kept the same during the operation, and the samples were taken simultaneously. The effects of the different positions of the splitters on separation and the feed rate were the parameters that were observed during the experiments. The performances of three spiral concentrators were found to be different. To clarify the effect of the particle size on the separation in spiral concentrators, the screening was applied to the feed. The samples were sieved from 75µm. The test results indicated that the separation performance decreased dramatically in very fine particles. Although fine particles caused some problems in spiral concentrators, fine grinding is required for this particular chromite ore for better liberation. A suitable method for the fine particles should be investigated for acceptable recovery.

Sep 1, 2012

By M. Y. Zhou

The paper elaborates on the significance of producing ultra-low-moisture ore concentrate, the operating principle and technical features of thermocompression- filtration process, the kinetics involved in the dewatering process, and the technological process system and equipment used. It is pointed out that it is possible to reduce the moisture of fine ore concentrate to a minimum. By way of example, the case of the treatment of flotation molybdenum (Mo) using the thermocompression- filtration process is cited.

Jan 1, 2014

By B. Courtaud

Uranium plants are generally located quite far from conversion plants, resulting in high transport costs. One way of reducing such costs involves putting more uranium in each drum by increasing the final product?s bulk density, which can be achieved via mechanical compaction of the powder and/or improved precipitation. For most of its plants, AREVA has adopted the latter approach, involving a new precipitation process applicable to all kinds of yellowcake produced (via uranates, uranium peroxide, etc.) that achieves bulk density of 3 for soda uranate, for example, instead of the 1.5-2 density available via conventional processes. At present, this process is being undertaken on an industrial scale and will become the norm for precipitation processes at all AREVA U plants. In addition to producing dense yellowcake, the process also delivers a product with no fines, a spherical particle shape (which allows for high-quality powder flow) and superior post-precipitation filterability

Sep 1, 2012