Search Documents

By Richard K. Komarek, Antonios Zavaliangos, Roman T. Dec

Roller presses are widely utilized in mineral industry for fine milling and compaction. Recently used models are providing only limited information about the material behavior in the roll bite. This paper introduces a 2-dimensional finite element model for analyzing those two basic processes. A pressure-dependent plasticity model with linear elasticity was used as a constitutive model for the particular material. Coulomb friction law was used to describe phenomena on the material/roller surface interface. Two basic roller geometries are considered: smooth (used for milling and compaction) and with cavities, commonly used for briquetting. Comparison of the results obtained from the model with experiment indicates that they are following the general trends of experimental values recorded with laboratory roller presses. It is shown, that the model is suitable to analyze material behavior through all stages of the rolling process: feeding zone, nip region, neutral plane and release section. It can predict pressure, shear stress, slip of the material over the roller surface, material velocity field, failure of the compact during release and the course of other important process variables. This allows the process engineer to gain an improved understanding, leading to a better process and equipment design and control.

Jan 1, 2003

By Lorenzo Reyes-Bozo, Ronaldo Herrera-Urbina, Pablo Higueras, Alex Godoy-Faúndez

"The copper mining industry in Chile and perhaps in other countries as well is faced with the challenge to implement the best practices in order to achieve a sustainable and more environment-friendly growth. Relationships between mining industry and society have been historically complex due to its environmental impacts. Whereas the ore grade has declined continuously, this has involved an intensive energy and water consumption thus increasing operational costs at different stages of the concentration process. In the case of copper sulphide ore concentration, froth flotation is the main technology used worldwide. The amount of the different chemical reagents used in flotation plants (i.e., collectors, depressants, frothers and modifiers) affects significantly production costs and has a negative effect on the environment as well. The objective of this research work was to evaluate the use of biosolids and their main components (i.e., glucose, proteins and humic substances) as more environment-friendly flotation collectors for chalcopyrite and molybdenite. For this purpose, microflotation tests were conducted in a modified Hallimond tube. In addition, FTIR and zeta potential experiments were performed to investigate the interaction of biosolids with these sulphide minerals. Biosolids and their main components may interact through physical and chemical ways due to different affinities with such sulphide minerals as chalcopyrite, pyrite and molybdenite, which are present in copper sulphide ores. In alkaline pHs, biosolids and their main components make the zeta potential of the sulphide minerals investigated more negative. These results may provide important information concerning the behavior of the main sulphide minerals in the concentration of copper sulphide ores at industrial scale, wherein mill processes could affect their surfaces properties. Therefore, biosolids and their main components may open an opportunity to be used in copper sulphide flotation plants to partially replace conventional reagents, which are more hazardous and less environment-friendly."

Jan 1, 2014

By Bulelwa Ndlovu, Saeed Farrokhpay, Dee Bradshaw

The effects of phyllosilicate minerals on the flotation performance and froth stability of a copper ore was investigated. It was found that various phyllosilicate minerals affect the copper recovery differently however they all caused the flotation grade to be reduced. The effect of different phyllosilicate minerals on the froth stability followed the order of talc >> montmorillonite > muscovite > kaolinite > illite. The results demonstrated that there could be a relationship between the deleterious effect of phyllosilicate minerals on the flotation and froth stability. Talc and montmorillonite have both shown the highest effect on the flotation recovery and grade as well as froth stability. On the other hand, illite has the least effect on the both flotation performance and froth stability. Kaolinite and muscovite also affected the copper flotation grade (but not the recovery) while they also affected the froth stability. Therefore it is possible to control the flotation performance when phyllosilicate minerals are present via monitoring and controlling froth stability which needs to be investigated further.

Jan 1, 2014

By József Faitli, Imre Gombköto, Barnabás Csoke, Tamás Magyar, Beáta Oláh, Sándor Nagy

"Raw materials are among the main building blocks of a growing economy. Without raw materials, no matter whether it is primary or secondary, production is not possible. Products with high added value require special materials. Recently, worldwide production of some important raw materials mainly comes from a handful of countries, for example: China (Rare Earths Elements (REE)), Russia, South Africa (Platinum Group Elements (PGE)), Democratic Republic of Congo (Cobalt), etc. In the EU as well as in Hungary, the importance of the so called 14 critical raw materials has been recognized. Within the frame of the TÁMOP-4.2.2.A-11/1/KONV-2012-0005 - CriticEL project, the Institute of Raw Materials Preparation and Environmental Processing in cooperation with the Institute of Mineralogy and Geology of the University of Miskolc are working on the exploration of the primary and secondary sources and developing innovative preparation technologies of critical raw materials in Hungary. The research work showed in this article, focused on the recovery of critical materials from LCD TVs and monitors. There are high deviations in different literatures regarding to concentrations of critical elements in displays (e.g.: indium), probably because of the differences in production year, producers and recovery technologies. During the research - described in this study - a well specified sample of quite large amount of displays had been used. The exact place and shape of the ITO (indium-tin oxide) layer were determined by SEM analysis. The applied preparation technology was developed based on the results of our investigations and by technologies found in the literature. The developed process accomplishes two main parts: the mechanical preparation (mainly the liberation of different display layers, removal of liquid crystal) and the acidic dissolution of indium."

Jan 1, 2014

By S. Kelebek, M. Davidson

"Flotation tests were conducted on a mixed copper ore sample containing bornite and malachite with trace quantity of other secondary copper minerals. The bornite component was very floatable, in sharp contrast to poor flotation characteristics of other copper minerals. A Box-Behnken experimental design methodology was used to study effects of three main reagents, namely potassium amyl xanthate (PAX), hydroxamate (Cytec 6494) and diethylenetriamine (DETA). Pine oil, as a frother, was used at a fixed concentration. Three main models constructed using a statistical software included malachite recovery, overall copper recovery, and copper grade. Bornite recovery was not modelled as its recovery was consistently over 99 % in the presence of hydroxamate and PAX. In each model, the hydroxamate dosage was the dominant parameter (at 95% significance level) determining the recovery of main components including that of gangue, which manifested itself by lowering the copper grade of the concentrate. In comparison, PAX was effective only at 90% significance level. DETA did not affect the overall recovery of copper or malachite significantly, but appeared to cause a significant decline in the concentrate grade, especially when used simultaneously with hydroxamate. Various quadratic models developed for the flotation system investigated are presented."

Jan 1, 2014

By Henrique Kahn, Daniel Uliana, Carina Ulsen, Guilherme Nery

"Gold has been a material in high demand since the dawn of humanity. After hundreds of years of exploitation, the increasingly search for gold occurs in lower grade deposits with greater extraction difficulty. Therefore, for maximum efficiency, deep knowledge of the characteristics of these minerals and their associations is crucial, which is acquired through an accurate and rigorous routine of process mineralogy and batch extraction tests. The industrial gold process extraction occurs by gravity concentration, sulphides flotation and cyanidation. For gravity concentration, it is fundamental to establish the proportion of free or coarse gold grains and its association to heavy minerals; regarding flotation, the most relevant data are the proportion of gold associated to sulphides and their liberation by the surface area; for cyanidation, it is crucial to evaluate gold accessibility and the kinetics of leaching. Thus, the characterization of gold associations and liberation is vital to establish the plant design, to optimize operating plants and to reduce gold losses. Our aim is the characterization of gold occurrence in low-grade Brazilian deposits with complex mineralogical assemblages to support processing flowchart definition and to predict metallurgical recoveries. Gold distribution in light and heavy minerals was evaluated by heavy liquid separation and the occurrence of gold in free or locked particles was carried out on heavy products by SEM-based automated image analysis using the MLA system. All the products of heavy liquid separation were cyanidated in head samples with different milling conditions to evaluate the reaction kinetics and maximum recovery."

Jan 1, 2014

By S. M. H. Haddad, M. Saghaeian, R. Hejazi

"Due to limited water resources in mineral processing plants, increasing the efficiency of iron tailing dewatering system in order to obtain more usable water is very important. In this research, flocculation process, as one of the best method for water recovery, was investigated by using one organic cationic and three anionic types of flocculants with different dosages (10, 20, 30 g/ton) and iron ore tailing slurry (8 % w/w solidity) in series of graduated cylinders and obtained results were compared. it is observed that for tailing sample, the anionic flocculants have a significant effect on the settling rate of solid particles compared to the cationic types. Furthermore, effects of temperature (10, 23 and 43 ºC) and pH (2, 7 and 12) on the rate of settlement and turbidity was studied by utilizing the best flocculant. Findings showed that by increasing the amount of flocculant dosage, sedimentation rate went up and turbidity decreased. Comparison the out-put data of tests indicated that at temperature 23 °C and pH=7, the best results for both of faster settling rate and producing more clear water were reached. It should be considered that lower temperature has a more negative effect on the sedimentation rate and overflow water quality. So it will be predicted that for cold seasons, the consumption of the flocculant powder would be higher than the moderate or warm seasons. Also, coagulation/flocculation was evaluated by applying organic cationic coagulant added to anionic flocculant in three different times. Different ratios of coagulant to flocculant was examined (70%:30%, 50%:50%, 30%:70%) as well. Overall, utilizing coagulant had desirable influence on sedimentation experiments and obtaining high quality water. 1- INTRODUCTION In mineral Factories, among the important processes, solid-liquid separation process due to limited resources of water is very important and operates on iron ore tailing in settling tank as thickener in order to gain clear water for preventing water loss and applying again in plant units (Ciftci and Serhat Isik, 2017). Iron ore tailing include inharmonious compounds of iron oxides, silicates and aluminum-silicates. The percentage of solid in the tailing usually changes between 5 and 10 percent (Dash et al., 2011). One of the major problem about dewatering of tailing in thickener is solid-liquid separation of slurries with high stability because of fine particles. It means that rate of sedimentation is very slow and recovered water quality is inappropriate. This issue can be solved to a large extent by factors such as pH control, ionic strength and flocculation/coagulation process which results in aggregation of particles so that settlement by gravity is happened (Dash et al., 2011)."

Jan 1, 2018

By R. Kobialka

In the article results of experiments over jaws? linings in jaw crushers with different shaping of working surface were presented. Following sets of jaws were under investigation: immobile plain jaw and moving jaw with grooving surface. Grooving jaws have groves with circular, triangular and trapezoid cross section. In order to evaluate efficiency of comminution both the grain composition of product and the content of irregular grains were determined, as well as the size of crushing forces and process efficiency were measured. For the combination: plain jaw with grooved one, a good results were obtained as regards the grain composition of product and the content of irregular grains. Crushing forces were higher at crushing with mixed types of jaws (the one plain, the second grooved), in comparison to crushing with using both grooved jaws. Efficiency of the process was definitely higher for mixed jaws.

Jan 1, 2014

The reactivity of clay minerals and variety of these reactions are greater than any other known colloidal material. While it is acknowledged that clay minerals can cause problems in mineral flotation, the literature contains conflicting evidence, particularly with respect to the effect of clays on froth stability. It is well known that achieving and maintaining optimum froth stability is an influential factor in determining froth flotation performance. However, the presence of clay minerals in the ore is a major challenge to obtaining a stable froth. In fact, clay minerals could reduce froth flotation performance by both decreasing and increasing froth stability. The mechanism by which clay minerals affect froth stability is not fully understood and needs to be investigated further. In order to improve flotation performance, reliable knowledge of the effect of clay minerals on froth stability is essential which is discussed in this paper. Keywords: froth flotation, froth stability, clay, clay minerals

Sep 1, 2012

By Valentine Chanturiya, Irina Khabarova, Maria Ryazantseva, Igor Bunin

"XPS investigations of the influence of HPEMP - treatment duration on the surface composition for natural chalcopyrite and sphalerite are described. HPEMP is a video pulse with a nanosecond front lasting between 5 and 10 ns. The electrical field component can reach 30 kV, whereas pulses repetition frequency is 100 Hz. In general, the formation of metal-deficient surfaces, polysulphides or elemental sulphur and oxides/hydroxides, were determined during the treatment for both sulphides as well as the essential differences of the way of mineral surface transformation during the treatment. The chalcopyrite surface shows the formation of elemental sulphur under the HPEMP treatment at 103 pulses while appearance of unstable sulphite species was detected at the chalcopyrite surface within 5 seconds (0.5•103 pulses) under the same treatment conditions. The results indicate that the quantity of adsorbed water (at.%) is changed considerably during the HPEM - treatment depending on treatment duration for both minerals. The concentration of water onto the chalcopyrite surface decreased during 30 seconds (3•103 pulses) of the HPEMP - treatment and it rose after the treatment at 5•103 pulses. The inverse dependency was obtained for sphalerite surface. Single mineral flotation tests have shown the significant increasing of the minerals recovery."

Jan 1, 2014

By A. Boulton

Low molecular weight synthetic polymers substituted with hydroxyl, carboxyl or sulfonate functional groups were used to improve the flotation separation of zinc or copper sulfide minerals from iron sulfide gangue minerals in three massive sulfide ores of different mineral composition. These polymers produced significant improvements in zinc or copper grades as a result of a selective depression of iron sulfide minerals. It was shown that this selectivity was the result of preferential adsorption of the polymer on the surface of the iron sulfide minerals. The different types of interaction between the functional group on the polymers and the sulfide mineral surfaces could explain the trends observed in the flotation results.

Jan 1, 2003

By L. E. Veki, S. M. Luukkanen, J. P. Karvonen, J. O. Leppinen

Today there is a consensus that xanthate adsorption on sulfide minerals is primarily controlled by redox reactions occurring at specific potentials on these semi-conductive minerals. Consequently, it is possible to control xanthate adsorption by controlling electrochemical conditions in the system by using oxidizing and reducing agents. The scope of this study was to investigate the possibilities to increase the selectivity of Cu-Fe-Zn ore flotation by applying electrochemical control in the conditioning of the flotation feed. In this work, mild steel grinding in a nitrogen atmosphere was used as the basis to provide a negative starting potential and minimize the amount of oxidation products on sulfide mineral surfaces. To study how different potential levels affect flotation results, a controlled conditioning procedure was utilized maintaining potential at a desired level by titrating the pulp with air. Xanthate adsorption kinetics during conditioning was examined by taking pulp samples for spectrophotometric analysis and laboratory flotation tests were conducted for samples that underwent the controlled conditioning procedure in the potential range of -200mV to +200mV vs. SHE. A clear correlation was detected between chalcopyrite recovery and the potential during controlled conditioning indicating that there was a constant increase in chalcopyrite recovery when the potential was shifted to more anodic values. It is possible that utilizing potential control in the conditioning stage, a smelter grade copper concentrate can be achieved directly in rougher flotation without cleaning stages. Conditioning in favorable conditions had significant positive effects on flotation selectivity of chalcopyrite. The improvement in copper concentrate grade being predominantly caused by the depression of pyrite. By applying the controlled conditioning procedure pyrite recovery in rougher flotation was reduced even low as under 1%, while in the tests without controlled conditioning, pyrite recovery varied between 7.5 – 65.7%. The result of this work indicate that affecting collector adsorption by electrochemical control in the conditioning stage can provide significant improvement in sulfide mineral flotation and industrial applications could lead to decreased chemical consumption, reduced equipment and maintenance costs.

Jan 1, 2018

By Pat Turner, Abrie Schutte, Tim Olson, Roman van Ommen

The key to good cyclone circuit design and operation in primary grinding circuits will be discussed. Cyclone circuit design issues include individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration. Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. The new gMAXTM. cyclones will be introduced and evaluated using operating circuit data in closed circuit grinding applications

Jan 1, 2003

By Katja Ohenoja

Polymer dispersants, also known as grinding aids, are widely used to reduce the viscosity of mineral particle suspensions and to improve energy efficiency during fine grinding. In this study, the effect of polymer dispersant with different molecular structure on the suspension properties in the wet stirred media milling of limestone was studied. The stability of suspension was studied by combining rheological and zeta potential measurements. The PDI value of polymers corresponds to the width of the molecular weight distribution so that low PDI corresponds to narrow MW distribution and high PDI to the wide one. In this study, two traditionally fractionated polymer dispersants with high PDI (over 2) and one novel polymer dispersant with low PDI (1.2) has been tested. It was noticed that dispersants worked as electrosteric stabilizators and prevented the agglomeration of ground limestone particles. The uses of dispersants could increase solids concentration used in the grinding experiments and at the same time lower the particle size and specific energy consumption. The obtained particle sizes were about 1 µm regardless of which dispersant was used or the amount of it. The novel dispersant with low PDI reduced viscosity most when compared with the traditionally fractionated polymer dispersants. Results indicated that even higher solids concentrations can be used at the same amount of dispersant when the novel low PDI polymer dispersant is used. Alternatively, lower dosage of novel low PDI dispersant can be used compared to traditionally fractionated dispersants.

Sep 1, 2012

By R. Singh

The paper presents the results of characterization and beneficiation studies carried out on a lean grade tungsten ore sample from Degana, India. Basically, three different routes, involving gravity separation, magnetic separation, and froth flotation were studied for concentration of the sample by physical and physico-chemical methods. Considering the low recovery by physical methods, efforts were put in to produce a tungsten concentrate by physical methods suitable for subsequent hydrometallurgical recovery of tungsten as ammonium para-tungstate. This strategy proved quite helpful in minimizing the losses of tungsten in tailings. Based upon these studies a novel integrated technological process flow-sheet was developed for the exploitation of lean grade tungsten ore deposit of Degana, India. Keywords: lean tungsten ore, characterization, beneficiation, gravity and magnetic separation, hydrometallurgical extraction, integrated process route

Sep 1, 2012

Optimising flotation designs and innovations is a complex process involving many parameters, one of which is ensuring sufficient testwork is carried out at plant level before these innovations are launched in the marketplace. This paper will describe how modern design tools are utilized, what are testwork phases at various plants and how results and observations have helped to validate and optimise flotation design innovations. Scale-up of equipment has long been the prevalent trend, but how long can it continue? Are there other means for pushing the boundaries of present technology? Some present challenges and future directions are given in the light of theoretical criteria for scale-up and how it has been applied in practice. Very large flotation cells of 300 m3 size have been installed in New Zealand, and relevant results from the metallurgical and mechanical aspects are presented and discussed. Utilization of the cell volume is also important. New innovations in the hydrodynamic domain are presented and discussed. Means to enhance flotation of coarse and fine particles are shown with results from plant testwork. Accurate control of large flotation cells is vital to optimize yields and grades. Froth image analysis and intelligent level control are presented ? again - with relevant plant results.

Jan 1, 2014

By M. N. Chandraprabha

Arsenopyrite is often associated with sulphides like pyrite, chalcopyrite and galena in refrac-tory gold ores. Selective flotation of arsenopyrite from associated sulphides is desirable for effective gold extraction when the gold is preferentially associated with the arsenopyrite matrix. By contrast, presence of arsenopyrite in flotation tailings poses a serious environmental threat due to arsenic dissolution. To prevent arsenic contamination from the mine wastes, it would be more economical and environmentally beneficial to remove this mineral during the froth flotation step. Use of Acidithiobacillus thiooxidans in the detoxification of arsenic containing sulphides is outlined in this pa-per. Biomodulation using Acidithiobacillus thiooxidans resulted in the preferential depression of pyrite from arsenopyrite. By suitable conditioning with cells and collector effective separation of arsenopyrite from pyrite was achieved. Biomodulation with wild cells did not yield separation of arsenopyrite from chalcopyrite. However, bacterial affinity could be induced to a desired sulfide mineral through environmentally controlled adaptation techniques. Through the use of arsenic-adapted bacterial cells, selective removal of arsenopyrite from chalcopyrite was readily achieved.

Jan 1, 2014

By Pramila Misra, Jibardhan Meher, Debadutta Das

The concentrated coal-water slurry has been receiving considerable attention recently due its ability to replace fossil fuels. Attainment of stable and concentrated slurry has been succeeded so far through several physical and chemical techniques. The present article reports the formulation and stabilization of a highly concentrated coal-water slurry formed from five varieties of non-coking coals with variable ash contents obtained from Eastern part of India, employing three varieties of starch esters, such as starch benzoate, starch formate, and starch carbamate as dispersant. The apparent viscosity of the modified coal-water slurry has been measured by varying coal loading, dispersant percentage, pH, temperature, etc. The apparent viscosity of the slurry has been found to be decreased substantially on addition of 0.8% of adsorbate in the slurry. The particle-particle interaction has been considerably decreased and stable concentrated coal-water slurry containing high weight fraction of coal (61.5-63.5%) has been achieved in each case. The slurries stay in a non-settling form for about a month with viscosity in a permissible low range. The coal-water slurry has been found to behave as a non-Newtonian liquid. Comparison of the zeta potentials of the naked and modified coals evidences that adsorption of the dispersants at coal-water interface results in inhibition of the agglomeration of coal particles through mostly steric repulsions.

Jan 1, 2014

By Guanghua Ai, Xiong Huang, Huashan Yan, Ting Li, Tingsheng Qiu

"Cyanide tailings of gold and silver concentrates contain considerable quantities of copper-lead-zinc sulfide minerals that can be recovered. However, the strong inhibition effect of cyanide often makes it difficult to recover these sulfide minerals effectively. In this research, a sample of cyanide tailings was investigated based on the principles of process mineralogy; activating flotation tests were carried out for the target minerals in the tailings, and the activation mechanism of the activator and its influence on the target minerals were investigated by Fourier transform infrared spectroscopy (FTIR). Mixed flotation of copper and zinc was carried out using QJ-01, a combined agent containing sulfite, as the activator of copper and zinc minerals, and ammonium dibutyl dithiophosphate (ADD) and butyl xanthate (BX) as the combined collector. Copper concentrate was obtained from the mixed concentrate by using a combined inhibitor of sodium sulfide and zinc sulfate to inhibit the zinc mineral. Zinc concentrate was extracted from the copper tailings by using copper sulfate as the activator and BX as the collector. The flotation test yielded copper concentrate with a grade of 22.56% and recovery of 76.96%, and zinc concentrate with a grade of 42.56% and recovery of 82.29%, which shows that comprehensive recovery of the sulfide minerals – copper and zinc –from the cyanide tailings was realized. The FTIR analysis showed that CN- was chemisorbed on the surface of chalcopyrite and sphalerite following cyanide treatment, while the combined activator QJ-01 containing sulfite reduced CN- into SCN- and weakened the complexing ability of CN- with metal ions on the mineral surface, thus achieving a good activation effect on chalcopyrite and sphalerite. The results of this study can provide practical guidance in increasing the resource utilization ratio of cyanide tailings in gold mines, and thus contribute to alleviating environmental problems caused by stockpiling cyanide tailings. INTRODUCTION Cyanidation, the most widely used technology for extraction of gold, has several advantages such as high recovery, process maturity, low cost, etc. According to available data, the annual discharge of cyanide tailings from China's gold mines exceeds 20 million tons (Li et al., 2011). Lower grades of exploitable gold ore entail increased discharge of cyanide tailings. Huge quantities of cyanide tailings are regarded as waste and stored, resulting in significant wastage of land resources. Moreover, residual beneficiation reagents, cyanide ions, and heavy metal ions in cyanide tailings cause severe pollution of water and land (Laitos et al., 2013; Donato et al., 2007; Mudder and Botz, 2004). In addition, cyanide tailings often contain valuable elements such as gold, silver, copper, lead, zinc, sulfur, and iron, which, if not recycled, would result in considerable wastage of resources. Hence, it is imperative to study the reduction and safety of cyanide tailings, and the mineral resources present in them."

Jan 1, 2018

By M. Saghaeian, R. Hejazi, M. Farahani, M. Dehghani, A. Tohry

"Wet tailing dams of iron ore processing plants typically contain a significant amount of valuable minerals. In more recent years, due to the increase in iron’s prices and technological innovations, as well as the low energy consumption which required for processing of materials from tailings, dams can consider as potential valuable deposits. However, the production of iron concentrate from tailings is usually complicated where the high moisture content of the material, the high clay content and the presence of chemicals of processing such as flocculants, acids and flotation reagents, all make materials highly sticky which can be easily swollen. In the present paper, the optimization of operational parameters to recover ultrafine hematite iron ore from the wet tailings dams of the Chador-malu iron ore mine was investigated. The optimization of operational parameters, showed that with modification of the washing unit components for slurry making, the challenge of constraints from feeding the plant could be overcome. To decrease the magnetite content in the tail stream of the medium intensity magnetic separation (MIMS) and subsequently increase the efficiency, the orifice of the cleaner tail flow exit pipe was changed from 7 inches to 3 inch and yoke angle changed from 14 to 8 degrees. These changes increased mass yield by 3% and decreased the magnetite content in the final tailings to 1.2%. By recirculating the cleaner SLons of final tailings within the circuit, the solid percentage of the feed to rougher SLons decreased to around 15%, and as a result the matrices were not overloaded that easily, and mass yield increased to about 13% from 7%. All the above mentioned optimizations were achieved without significantly affecting the concentrate Fe grade."

Jan 1, 2018