Search Documents

By D. Izerdem, S. L. Ergun

"Beneficiation of the finely disseminated valuable minerals has been an important issue in the mineral processing field for decades. Treatment of the fine materials becomes difficult with using traditional gravity concentration equipment. To investigate particles behavior in a commonly used conventional gravity concentration equipment, a comprehensive study was undertaken in a plant, which only consists spiral concentrators as concentration units. Spiral concentrators require relatively coarse material to effectively concentrate valuables as well as offering greater simplicity for especially higher grade feeds. In the current work, chromite ore (d80 = 290 µm) was treated using spiral concentrators and the performance of spiral concentrators was examined. The design of the separation circuit comprised of rougher, cleaner and scavenger stages. The resultant fractions produced by each separation unit and feed samples were analyzed to identify the particle sizes, mineral liberations and chromite content. Grade and recovery comparisons were presented in size-by-size manner and the separation tendency of the particles were determined in varying feed rate conditions. The overall results indicated valuable mineral loss of the plant and alternative suggestions were pointed to reach the target values.INTRODUCTION Spiral concentrators are simple low energy consuming devices, which are generally used for pre-concentration of the minerals. They are cost efficient equipment separating minerals mainly based on density differences of the minerals. The adjustable splitters remove the concentrate as the remaining stream continues to move down the spiral. Separation on a spiral is achieved through a combination of forces that act on particles as they move down the trough of the spiral. The main forces known to act on the particle on a spiral are the gravitational force, centrifugal force, hydrodynamic drag and Bagnold force (Atasoy and Spottiswood, 1995; Burt, 1984). Since the classification in a spiral concentrator depends on particle specific gravity and size, the operation of spirals can be analyzed using size recovery or partition curves (Bazin et al., 2014). Spiral concentrators possess multiple design parameters for a variety of applications. The design parameters that govern the performance of the spiral can be identified as the diameter, number of turns, slope, pitch and the profile of the trough. For an efficient separation on a spiral concentrator, the properties of the slurry flowing on a spiral, ore texture, percent solids and flow rate play important roles."

Jan 1, 2018

By Andrzej Luszczkiewicz, Magdalena Duchnowska, Jan Drzymala

A selected flotation system of beneficiation of the copper ore at KGHM Polska Miedz S.A. has been analyzed in the article. It was found that a proper assessment of upgrading must be based on two elements, that is the upgrading process selectivity and working point of the considered flotation unit, both determined, preferentially by means of the Fuerstenau recovery-recovery upgrading curve. The Cu recovery - non-Cu components recovery upgrading curve was selected for calculations because its background lines (no separation and ideal separation) are insensitive to changes in the grade of feed of the processed material. This approach allows a comparison of upgrading results for feeds having different grade, being upgraded in various flotation machines and under different physicochemical conditions. It was shown in the paper that the main criterion for comparison of two working in parallel systems is selectivity of upgrading. However, when two flotation machines, despite of the same selectivity, produce concentrate and tailing of different grades, it is necessary to analyze their working points using upgrading curves. The proper position of the working point depends on the criterion imposed on the process and is a result of not only basic parameters of the upgrading process such as feed, concentrate and tailing grades but also on economic parameters such as costs associated with the production of concentrates and the time needed for their production.

Jan 1, 2014

By David De Klerk, Maximilian Richter, Thirunavukkarasu Pathmathas, Indresan Govender

We consider the average power dissipation distribution for dense granular flows of an idealised mono-sized charge (5 mm glass beads) in a 300 mm diameter tumbling mill operated in the cascading-to-cataracting Froude regime. By combining the inherent frictional nature of particles within a dense flow regime and noting that tumbling mills are typically characterised by collisional and turbulent stresses, we derive the power dissipation distribution for athermal boundary conditions. The input data to the model (velocity, solids concentration, pressure and flow depth) are obtained directly from non-invasive measurement using a nuclear imaging technique: Positron Emission Particle tracking (PEPT). The power dissipation due shear stresses is shown to be the dominant mode of dissipation in the tumbling mill with up to two orders of magnitude difference between pressure induced dissipation and shear.

Jan 1, 2014

By Vishal Shukla, Ashok Kumar, Manas Ranjan, D. Chakraborty, Narayan Sharma

Jigging has a very important role in mineral processing Industry. Upgrading of Iron Ore by jigging has been an emerging trend. A detailed investigation is carried out to understand the influence of Jig feed granulometry and bed height during jigging operation. Noamundi jig plant data shows that variation in jig feed granulometry, feed quality and bed height are major contributors to fluctuation in jigging performance. At Noamundi the feed size (-10.0+0.5mm) fraction is used for fines jigging operation. To understand the effect of granulometrey on jig plant performance such as yield, separation efficiency and Fe recovery. In this context The performance of jigging was evaluated by daily average data from jig operation was used to study the influence of feed distribution on jigging performance .Coarser fraction (+6mm) has a positive influence , whereas fines fraction (-0.5mm) tends to lower performance . During Jigging rearrangements of Particles takes place due to an alternate expansion and compaction of Jig Bed .These particles are arranged by increasing density from top to bottom. During the particle stratification, Jig bed physically cut at desired horizontal particle density plant to separate the desired product. Investigation shows that optimum bed height is required at different Jig feed quality to achieve desired product quality, maximum separation efficiency and Fe recovery. This Paper will illustrate role of granulometry and Bed height control on Jigging plant performance.

Jan 1, 2014

By S. M. Marr

"Water availability and water-related environmental impacts are now one of the most significant challenges facing primary production within the global minerals industry. Whereas the industry has, to a large degree, been able to demonstrate a collective response to greenhouse gas emissions and global energy demand, no such strategy exists for water. In part, this is because water quality and availability are regional issues, but also too because water quality cannot be defined by a single attribute, and extrapolation of any set of water quality indices to their associated environmental impact is no trivial matter. In design situations specifically, the situation is exacerbated by the fact that process engineers typically focus on site water management, and consent authorities are primarily in catchment level issues. As a result, an integrated approach to water management is difficult. This does not stem from an unwillingness by members of the professional team to engage with the total picture of water quality and availability, but principally from the fact that there is no common language through which to approach the problem.It is imperative for process engineers to extend their design system boundary, to reflect the geographic scales over which water impacts need to be quantified. It is not suggested that chemical engineers and metallurgists should become experts in geochemistry, hydrology and limnology. Rather, the challenge is to develop tools through which better communication of the relevant environmental impacts can be achieved.It has been estimated that 50% of the capital for new plants is devoted to handling wastes. The integration of mass exchange processes, adopting a life cycle analysis framework for considering environmental impacts and shifting the emphasis from effluent concentration to environmental impacts should be adopted in the framing of the design problem have been suggested as techniques of Environmentally Conscious Design. Shifting the focus from effluent concentrations and legislative requirements to evaluating the environmental impact is an important step towards improving the overall environmental performance of a process facility."

Jan 1, 2003

By Z. Chen

This study is concerned with the behavior of bubble clusters in a well-controlled turbulent flow. We used a specially designed cell where the bubble aggregates could be formed and exposed to breakage by a rotating impeller. The effects of impeller speed and the concentration of collector on cluster behavior were studied. It was found that the size of the clusters increases with the concentration of collector used. We also found that although the clusters could easily be destroyed under the action of impeller, they could reform, especially at lower impeller speeds. It was observed that the size of the bubbles arriving into the impeller region in the absence of particles before breakage was considerably higher than the size of the clusters formed at the same impeller speed. It appears that both cluster breakage and re-formation take place simultaneously, and the extent of formation and regrowth is mainly determined by the hydrophobicity of the particles and the impeller speed.

Sep 1, 2012

By Ming’an Wei, Chuanyao Sun, Yangge Zhu, Fayu He, Yanbo Shang, Xingrong Zhang

In order to discuss the separation mechanism of copper-molybdenum ore, surface electronic structures of chalcopyrite and molybdenite were studied in the paper, by using First Principles method of quantum chemistry. So, the separation mechanism of thioglycolic acid (TGA) with chalcopyrite and molybdenite was revealed better. The results showed that differences of the electronic structure of chalcopyrite and molybdenite could directly affect their interactions with TGA, such as band structure, density of states, Mulliken populations, and so on. And the frontier orbitals of chalcopyrite and molybdenite were also calculated by Dmol3 after the optimization by CASTEP, from which the interaction energies between minerals and TGA were obtained and compared. So, the essence of flotation separation of copper and molybdenum were well revealed.

Jan 1, 2014

By Ashok Kumar, Subhadra Sen Dr. Rashmi Kumari, D. P. Chakraborty, Ajay kumar Gupta

The blast furnace coke quality depends on the characteristics of coal blend, pre-carbonization techniques adopted such as stamping, vibro-compaction etc., and coking conditions. Of the above, coal blend plays a significant role in the production of quality coke. Furthermore, the quality of the blend depends on the quality of individual coals and their interaction making up the blend. During transportation and stockpiling, coal is in contact with air for periods of time that sometimes may exceed several months. During this time, reaction with oxygen in the presence of water, sunlight and possibly elevated temperatures may take place. The resulting weathered coal suffers some alteration in its technological properties, which in turn affects coke quality for Blast Furnace operation adversely. In this work, two coals belong two prime hard coking and hard coking categories, namely Illawarra & Tahmoor, were selected and kept in a separate stock pile for a period of 120 days. These coals were characterized in terms of proximate, rheological & petrography properties at a regular frequency. This report summarizes the impact of weathering on the coking behaviour of these two coals in terms of properties as mentioned above. However, the rate of loss depends on coal rank and storage conditions. This has been seen through this study that the loss depends on coal rank and storage conditions. Deterioration of rheological and petrographic properties were seen higher for low-rank coals, like in this study Tahmoor, which is a low rank coal, compared to Illawarra showed higher degree of coking property degradation within the same time period under identical environmental conditions. Low-rank coal deteriorates at a faster rate because low-rank coal is dominated by free radicals that easily react with oxygen, resulting in the creation of various carbonyl groups and weathered vitrinite. Based on the results obtained in this study, size of stock piles for different qualities of coals to be maintained, at a specific time, can be determined and recommended, so that target coke quality is always achieved.

Jan 1, 2018

By Masoud Askari, Ahmad Rafizadeh, Shahamat Rostami, Mohammad Qaredaqi

Gole - Gohar Iron ore mines located in Sirjan, Southeast of Iran, have more than 1 billion Iron ore deposit and this area comprises 45 % of Iran Iron reservoirs. The aim of Wet tailing processing line is recovering Hematite ore from wet tailing of Gole - Gohar iron ore processing plant. The Investigations of Hematite recovery plant showed that the recovery of Iron ore to concentrate in Wet Tailing Processing (WTP) line is very lower than that has been predicted, sampling, and designing of the process parameters are not accurate and designed magnetic field intensity is not reasonable for the recovery of Iron in form of Hematite in this line feed. Applying of MIMS in WTP separator and changes in circuit caused in overwhelming increase of Fe recovery, from 11 to 40%. Although recovery of WTP line was improved, but low recovery of this processing line and high content of Hematite ore in WTP tailing, made applying Wet High Intensity Magnetic separators unavoidable. Two kinds of WHIMS have tested for processing of WTP line tailing. Results showed that traditional Jones separator with grooved plate matrix, is more suitable to achieve a better quality of concentrate compared to Slon® separator.

Jan 1, 2014

By A. Tolentino, J. Bravo, M. A. Corona-Arroyo, C. Quintero, R. Zarate, A. Lynch, L. Carillo

"This paper presents the performance of the flotation circuit of Minera Fresnillo PLC, Mexico. A plant survey was carried out on the lead banks and a size-by-size assay on the samples was conducted. The results indicate that the plant is treating fine particles in the flotation circuit. At least 30% of the particles in the feed are finer than 8 microns and that high amounts of Pb, Au, Ag and insolubles are in this particle size. It was also found that higher percentage of insolubles in the -8 micron particles are recovered in the final concentrate rather than being rejected in the tails. The presence of high amounts of insolubles in the concentrate is an issue of the company. The result of the plant survey provided valuable information for effective reduction of the insolubles in the concentrate and for plant optimization. The work conducted is part of the training of the students involved in a mine placement in the Alban Lynch Student Venture. INTRODUCTION Minera Fresnillo is one of the operating mines and the main contributor to the silver production of Fresnillo PLC group, the world’s leading producer of silver from ore. It is located in the mining district of Zacatecaz, Mexico, approximately 650 kilometers from Mexico City. The major minerals that make up the ore are galena, sphalerite, tetrahedrite, pyrargyrite, proustite, polybasite, pyrite and pyrrhotite. Minera Fresnillo has a capacity to treat 8300 tonnes of ore per day. The plant consists of semi-autogenous mill - ball mill – hydrocyclone circuit for primary grinding followed by silver-lead flotation then zinc flotation circuits. This paper reports the plant audit conducted in the silver-lead flotation circuit (Figure 1) of Minera Fresnillo. The circuit includes rougher, scavenger and two stages of cleaning. The tails from the scavenger goes to the zinc flotation circuit while the second cleaner yields the final silver-lead concentrate. The feed to the circuit has a particle size of 90% finer than 75 microns and generates a concentrate with grade of about 35% Pb, 5700 g/ton Ag, 16 g/ton Au and recoveries of 90% Pb, 90% Ag, 64% Au, respectively. Although the plant achieves their target concentrate grade and recovery, the concentrate also contains significant amount of insoluble materials which is about 18%. These insoluble materials consist of gangue minerals. The plant audit was conducted primarily to determine the possibility of further reducing the amount of insoluble materials present in the silver-lead concentrate."

Jan 1, 2018

By James Y. Oldshue

"Very seldom is it possible when contacting a gas with a slurry to measure the dissolved gas concentration in the slurry, and even were it possible, seldom are equilibrium data available with a suitable Henry’s law constant.In general, by assuming a reasonable value for the dissolved gas concentration in the slurry and a corresponding equilibrium gas partial pressure P*, Kga values can be calculated for the pilot plant and scaled up. Then, with the same P* value at various reaction conditions, a mixer can be designed which is quite satisfactory, having a reasonable design factor for full-scale performance.We will take as an example a slurry of a known solids composition and use a continuous 4 tank system. By assuming a percentage saturation of the dissolved gas in the first tank, the dissolved gas concentration can be obtained in the other three tanks. It usually is possible to measure the off-gas composition in each of the 4 tanks. If the top of the tanks is connected in the form of a multi-compartmented horizontal autoclave, then a modified top off-gas composition in each compartment must be used."

Jan 1, 2003

By Kang N. Zhong, Hui H. Luo, Yunan Phosphate Chemical Co., Yi H. Wei, Yao J. Li, Yu L. Wang

"The three kinds of phosphate ores (igneous, metasedimentary and sedimentary) found in China have great differences in flotation flowsheets and reagents suite because of their crystal structure and mineral composition. The igneous and metasedimentary apatites have good floatability with fatty acid as collector and waterglass, sodium hydroxide or sodium carbonate as conditioners. The sedimentary phosphate is very difficult to beneficiate by direct flotation because of their poor floatabilities and relatively high content of MgO and SiO2, even though the dolomite depressants are used sometimes.The differences in floatability of apatites in China are closely related to their differences in specific surface area. The amount of collector to float apatite increases with the specific surface area. Apatite with lower specific surface area showed good floatability at lower collector concentration. Apatite with a higher specific surface area needed a higher concentration of collector. The content of CO3 2- will affect the specific surface area of apatite by distortion of its crystal structure and consequently affect its floatability.Dolomite can be easily rejected from apatite in a weak acidic medium (pH=5), especially in phosphoric acid medium by reverse flotation. Quartz and siliceous gangue in sedimentary apatite can be removed by direct flotation using fatty acid or by reverse flotation using amine. Amine is not practically applied because sedimentary apatite in China is usually very fine and needs fine grinding, which always results in excessive, very fine, stable and non-flowable foam.Based on the floatability of phosphate ore in China, a two-stage flotation process, direct and reverse flotation (D+R), was developed to beneficiate sedimentary ore. For the Haikou phosphate ore containing 25.11% P2O5, 3.46% MgO and 16.5% SiO2, a concentrate containing 31.84% P2O5, 0.48% MgO and 14.8% SiO2 can be obtained through a continuous D+R test at a recovery of 89%."

Jan 1, 2003

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

The research aimed to compare the chemical analysis (K, Na, Cl) of Iranian concentrate plants, which are the main source of materials corrosion in the pelletizing plants. Cl alongside alkaline elements (especially K) may cause corrosion and plug in the grate plates and other involved equipment. Therefore, it is tried in the processing plants to remove impurities from the concentrate to prevent potential problems in pelletizing and iron/steel making processes. Part of these impurities are existed in the nature of ores and others are sourced in the processing water. Various samples from the largest Iranian concentrate plants including Chadormalu, Gol-e-Gohar, Jalal-Abad and Sechahun were prepared to investigate the possibility of alkaline problems for each samples. The amount of Cl, K and Na of Chadormalu sample was obviously low and therefore no alkaline problem is expected. The Cl content of Gol-e-Gohar sample was high (980 ppm) while amount of K was less (0.008 Wt. %). Due to low content of K, most of Cl will release as Cl2 or HCl and so problems caused by KCl plugging would not be a problem. The amount of Cl in Sechahun case was nearly same as Jalal-Abad (400-600 ppm), higher than Chadormalu and less than Gol-e-Gohar samples. However, the K content was higher than all samples (0.04 Wt. %). Therefore, the amount of evaporated K would be 2-4 times more than other samples. Since the amount of Cl and K is simultaneously higher than usual iron ores, therefore alkaline problems may be a serious prevention factor for the continuous operation of this plant. In order to solve this problem some counter-measures is suggested and discussed including cleaning system, partial dust enriched with KCl removal and variation in the materials type of involved equipment.

Jan 1, 2018

By D. Saramak

The proposal of the nip zone angle determination in HPGR crushing process is presented in the paper. Knowledge of the nip zone angle value, in turn, makes it possible to determine the real maximum pressing force in the high-pressure comminution. Two methods of determination of this maximum pressure were proposed and verified. The first method is based on the roll?s geometry, and the change of the HPGR chamber?s volume together with the roll rotation, while the second one considers the outlet gap width impact. Results of the nip zone angle calculations according to both methods are similar and show convergence with the real operating conditions. The verification was carried out in a piston-die press, and experimental results show that methodology of the nip zone angle determination presented in the paper has its practical confirmation. A proper determination of the nip zone border makes it possible to calculate the comminution probability of given type of material and is a basis for the HPGR crushing process modeling and optimization. Keywords: HPGR, comminution, nip zone, ore processing

Sep 1, 2012

By J. Quinteros-Riquelme

Despite increasing demand, the supply of silver is limited by its inadequate recovery from ores. Due to its scarcity in nature, its high ore variability and complex mineralogy of current silver deposits, its recovery by mineral froth flotation presents a real challenge for process engineers. A silver ore often contains significant amounts of five to ten different silver minerals and knowledge of the mineralogy is a necessary precursor to flotation testing. In this work, a complex silver ore was treated by using batch laboratory flotation, in an effort to find the best experimental conditions to obtain the optimal silver recovery. Mineralogical characterization of feed samples was conducted using a combination of tools, namely the mineral liberation analyzer (MLA) and inductively-coupled plasma mass spectrometry (LA-ICP-MS), which indicated that most of the silver occurred as ?invisible? silver in pyrite. The pyrite assay of the ore was approximately 4%. The ore was processed in two flotation stages. The first stage, sulphide flotation, aimed to collect a sulphide mineral rich concentrate; then a non-sulphide flotation stage was performed by adding sodium sulphide and collectors to the remaining material in the cell, with the objective of obtaining a pyrite rich concentrate. To reach the target recovery of silver from this ore, various variables were altered. In the first stage: mixed collectors, activators, dispersants, and mainstream inert grinding were assessed. In the second stage, the conditions for sulphidization and subsequent flotation were both investigated. From the grade recovery curves for silver and sulphur it was possible to observe a similar metallurgical behavior for both elements, supporting the results given by the mineralogical characterization. Keywords: silver oxide, froth flotation, sulphidization, mig

Sep 1, 2012

Under the AMIRA P9 project the three-product cyclone-an off-shoot of the conventional hydro-cyclone-that produces three distinct products has been developed. The three-product cyclone shows great promise as a classifier in mineral processing. Industrial and pilot plant trials performed to assess its performance in the classification of the UG2 platinum ore, indicate that the presence of an extra overflow product stream that captures the mid-sized particles, provides improved classification efficiency. To assess the split on component density, samples from the feed and product streams were screened and assays by size for chromite (? = 4.8) and silica (? = 2.65) were obtained. Results from tests performed using this type of hydrocyclone in a number of applications indicates that it can be applied successfully in circuit configurations where the conventional hydrocyc-lone is not suitable. Utilising the three-product cyclone to classify the UG2 platinum ore resulted in an intermediate overflow product stream containing the mid-sized low density silicates and relatively fine high density chromite particles while the finer overflow contained mostly fine silicates and chromite particles. The coarse chromite and silicates reported to the underflow. Due to the increased number of products, the method of using efficiency curves was extended to cater for the increased number of products in the three-product cyclone. Although significant differences in the classification performance of the three-product cyclone were noticed with variations in machine variables a consistent method of assessing the performance was applied. The efficiency curve was adopted and applied and separate efficiency curve properties were obtained for each product stream. The methodology was applied to the component data, and efficiency curve proper-ties for each key component were obtained and compared. This paper discusses the application of the efficiency curve to cyclones producing more than two products and extending the methodology to the different components in the feed.

Jan 1, 2014

By Xiong Dahe

In recent years many creative technologies are applied to SLon vertical ring and pulsating high gradient magnetic separators. SLon-2500 and SLon-3000 vertical ring and pulsating high gradient magnetic separators are created towards larger scale. Through optimizing the magnetic system and lowering the electric current density, their energy consumption is obviously dropped. New magnetic matrixes are developed to raise the beneficial efficiency of valuable minerals. Special SLon vertical ring and pulsating high gradient magnetic separators are developed which can treat coarser particles of 0-5 mm. Through these technology creations, the mineral processing efficiency of SLon magnetic separators is further raised and their processing cost dropped. Therefore, they have been found wider applications. SLon-2500 applied in Essar Steel of India. In 2007, Essar Steel did a test on its Kirandul hematite ore with SLon magnetic separator and got very good results. The feed grade is 59.77%Fe, after SLon one roughing and one scavenging, the total iron concentrate grade is 65.00%Fe and iron recovery 93.86%. In 2008-2010, the company bought 10 SLon-2500 magnetic separators to treat such iron ores. In 2010 the first SLon-3000 was applied to processing ilmenite. The magnetite-ilmenite deposit is located in Pan Zhi Hua, Si Chuan Province of China. The ore processing flow sheet is: Drum low intensity magnetic separator is used to take out magnetite, and then the SLon-3000 is used to recover ilmenite for roughing. The mags of the SLon-3000 are further cleaned by flotation. The SLon-3000 average operational results are: feed grade 9.52%TiO2, mags grade 17.43%TiO2, mags mass ratio 41.01%, TiO2 recovery 75.09%, non-mags grade 4.02% TiO2, non-mags mass ratio 58.99%. SLon magnetic separators Applied to treat 0-5mm limonite: The feed of SLon magnetic separator is usually 0-2 mm which needs to be ground by ball mill. As many Chinese iron ores are poor grades, if we can throw part of tails before grinding, the grinding cost will be greatly reduced. In 2010, a SLon-1500 and a SLon-2000 were specially built to treat 0-5 mm limonite. The feed grade is 26.51%Fe, mags grade 53.20%Fe, iron recovery 64.26, and tails grade 13.66% Fe. SLon-2500 applied to purify quartz. In 2009, a SLon-2500 magnetic separator was applied to purify quartz in Shan Xi province. Its feed is 0-1mm quartz which contains 0.15%-0.25%Fe2O3, the designed non-mags grade need to be less 0.08% Fe2O3. The production results of SLon-2500 non-mags are 0.05-0.06% Fe2O3, much better than the designed data. SLon applied in Si Jia Ying Iron Mine to recover hematite. Si Jia Ying is a big oxidized iron mine located in He Bei Province of China. In 2005-2010, a plant annually treating 10 million tons of oxidized iron ore was built in which 39 SLon magnetic separators are applied. The total flow sheet results are: Feed grade 30.44%Fe, iron concentrate grade 66%Fe, iron recovery 80%Fe, tails grade 9.65Fe%. SLon applied to recover specularite. Li Lou Iron Mine in An Hui Province of China built a plant annually processing 5 million tons of iron ore in 2010-2011. 25 SLon-2000 magnetic separators are applied to recover specularite. The total flow sheet results are: Feed grade 31.65%Fe, iron concentrate grade 65%Fe, iron recovery 80%Fe, tails grade 10.37%Fe. SLon applied in Da Hong Shan Iron Mine. Da Hong Shan Iron Mine is located in Yun Nan province of China. It treats 4.5 million tons of oxidized iron ore annually. 15 SLon-2000 magnetic separators are applied to recover hematite. The total flow sheet results are: Feed grade 35.61%Fe, iron concentrate grade 64.95%Fe, iron recovery 74.08%Fe, tails grade 15.55%. Keywords: SLon magnetic separator, iron ore, ilmenite, quartz, beneficiation

Sep 1, 2012

By Felipe Sepulveda, Edelmira Gálvez, Luis Cisternas

"In mineral processing, the recovery and/or concentration of the value components cannot occur in one operational stage, therefore requiring the use of separation circuits based on several flotation stages. The components to be separated are typically distributed at different concentrations and different particle sizes, resulting in different levels of recovery. Typically, more than one value component must be selectively removed by exploiting the differences in the components’ floatability at different pH values, pulp potential and particle size. Several methods for the design of these circuits are available in the literature, but comparatively few studies present circuit analysis tools or address the design of a multiple-product flotation circuit. In this study, global sensitivity analysis was used to analyze a flotation circuit with several products, such as copper, lead and zinc. This analysis was based on the Eureka mine concentrator plant. The analysis was performed for each of the sections of the circuit as an overall evaluation of the circuit. The Sobol’ method and the correlation method were used to evaluate the Eureka mine concentrator plant using the SimLab 2.2 software."

Jan 1, 2014

By M. Wright, A. H. Mwale

Opportunities to promote enhanced eco-efficiency (i.e. the simultaneous improvement in economic and environmental performance) for the minerals industry exist across the whole value chain. However, given the current operational models of major companies within the industry, and their focus on refining of primary ore bodies, it is important to understand where such opportunities might lie within minerals beneficiation, as it is here that major environmental pressures are felt. This paper examines the combination of unit technologies in a minerals beneficiation train, and explores the inter-relationship between energy input and water consumption for a given mineralogy and product recovery, as these are two critical environmental issues which affect the overall viability of many minerals plants. In particular, we review constitutive relationships for each of the sub-processes of comminution, flotation, and tailings dewatering, and suggest how these might be integrated into a unified hybrid model, with particle size distribution as the key design variable. Such a model can then be used to explore the trade-offs between different performance objectives (be these technical, economic or environmental) as part of a multiple-objectives optimisation exercise. In this way, it may become practical to envision situations in which concentrate grade and recovery are sacrificed, marginally, in order to reduce energy demand in comminution, and improve overall water recovery. In addition, this work provides a useful baseline against which to analyse the potential for dry processing. This becomes more relevant as the industry commits to advancing the sustainable development agenda in the face of the increasing life -cycle costs and impacts of minerals processing operations, coupled to declining ore body grades, and the desire to maximise recovery of minor and trace elements. Some specific observations for copper are offered, supported by operational data from Zambian copper mines.

Jan 1, 2003

By Xiong Dahe

"SLon vertical ring and pulsating high gradient magnetic separator utilizes the combined force field of magnetism, pulsating fluid and gravity to beneficiate weakly magnetic minerals with the advantages of large beneficial ratio, high recovery, matrix not easy to be blocked and excellent performance.We have developed SLon-750; SLon-1000; SLon-1250; SLon-1500; SLon-1750 and SLon-2000 VP HGMS. Now more than 200 of them have been successfully applied in China.Application in Qi Dashan Mineral processing Plant of Anshan Iron and Steel Company: The iron ore consists of magnetite and hematite. In 2001, six SLon-1750 magnetic separators are applied to control the tails grade of fine hematite. The results of flowsheet is: feed grade 30.15%Fe, concentrate grade 67.00%Fe, iron recovery 75.86%. The results set up the historic high record of this plant and the processing coast is greatly reduced.Application in Gushan Iron Mine of Ma Anshan Iron and steel Company: There are 6 SLon-1750 and 4 SLon-1500 magnetic separators applied in this mine to treat refractory hematite ore. The feeding grade is about 45%Fe. The final iron concentrate grade is about 60%Fe and the iron recovery is about 76%. The results are much better than the previous gravity flowsheet.Application in Meishan Iron Mine of Shanghai Baoshan Iron and Steel Company: The mined ore consists of magnetite, hematite and siderite. Because of a relatively high content of phosphorus, the iron concentrate could not meet the market requirements. Now 18 SLon-1500 magnetic separators are applied to reduce phosphorus, which is reduced from about 0.4%P to 0.246%P. The quality of iron concentrate is greatly upgraded.Application in Panzhihua Ilmenite Processing Plant: In the past, the -0.045mm ilmenite fraction was discarded in to the tails because of lack of high efficient equipment. In 2001, the plant built up a magneticflotation flowsheet to recover the fine ilmenite from the -0.045mm fraction with 6 SLon-1500 magnetic separators. The total results are: feed grade 11%TiO2, concentrate grade=47% TiO2, recovery 44%. Each year the flowsheet recovers 60,000t fine ilmenite concentrate."

Jan 1, 2003