Search Documents

By John Starkey

"The development of the SAG Power Index (SPI) Test in Canada has created a new and accurate way to measure ore hardness in a SAG environment. Coupled with the standard Bond Ball Mill Work Index Test it is now possible to determine from these two relatively inexpensive laboratory tests, the amount of energy required to grind an ore from the primary crushed size to the desired liberation size. By testing multiple samples to discover where the hard and soft ore zones are located, the representative hardness distribution for the ore body can be determined and grinding equipment selected that is capable to meet production targets for all mining areas of the deposit.Previously, it was deemed prudent to select up to 50 t samples of ore for Semi Autogenous Grinding (SAG) pilot plant tests and a second 5 t sample for metallurgical pilot plant work. The methods outlined in this paper show how the 50 t sample is no longer required for SAG design because it is better to measure the representative hardness distribution of the ore body than the hardness of a “chosen” representative sample. This is demonstrated to be true by the fact that the lower horizons of an ore zone cannot initially be accessed to recover 150mm pieces, and the bulk samples taken, rarely represent the desired design hardness of the ore. Median hardness will not yield a good result in most cases and a clear understanding of the location and extent of the hardest zones is imperative to achieve a truly successful grinding circuit design.This paper discusses two plants (Kubaka and Agnico Eagle) that have been designed using SPI and Bond with no pilot plant test backup. Both have been very successful in that they can grind design tonnage on the hardest ores in the mine. This guarantees that the mine’s profitability is protected in any mining sequence. It also allows the extra power to be converted to higher throughput on softer ores if additional cash flow is needed. The advantages from the owner’s point of view are dramatic. This procedure will be attractive as well when considering the costs for test work, and the samples for testing. Existing diamond drill core is normally used and this allows the inclusion of data from the deepest regions of the mine. In addition, it is also clear that the decision to use a crusher can now be made at the design stage of a project based on measured parameters and the estimated capital costs of alternative designs."

Jan 1, 2003

Beneficiation and dephosphorization of refractory oolitic hematite ore are investigated in this paper. It is shown that single magnetic separation, gravity separation or flotation is unable to recover iron effectively from the ore due to the complex mineralogy. The joint separation by spiral chute-shaking table shows a prospect for the treatment of the ore. An iron concentrate with 58.67% iron grade and 51.93% recovery is obtained by the joint separation of spiral chute and shaking table under the fineness of ?0.074mm 90% and dispersant dosage of 2kg/t for a sample ore of 37.51% Fe and 0.88% P. However, P content in the concentrate is still up to 0.52%. Dephosphorization from the concentrate is hence carried out. The final iron concentrate assaying 59.26% Fe and 0.056% P is obtained when the concentrate obtained by joint separation is leached by sulfuric acid of 1% (mass fraction) with solid percentage 10% at room temperature for 10min.

Jan 1, 2014

By Tamara F. Kondrateva, Evgenia E. Savari, Galina V. Sedelnikova, Rauf Y. Aslanukov, RAS (INMI), Grigori I. Karavaiko

"The investigation is dedicated to study of biohydrometallurgical processing of refractory gold-arsenic concentrate with the large content of pyrrhotite. Sulfide concentrate of chemical constituents: 75g/t Au, 4,7g/t Ag, 6,3% As, 29,3% S, 2,3% Sb, 0,5% ? (organic) and of mineral composition, %: 11,8 arsenopyrite, 39 pyrrhotite, 12 pyrite, 2,9 antimonite and the rest – aluminosilicates, carbonates and quartz, was studied. The recovery of gold from concentrate by cyanidation is 51,2%. The rest of gold is embedded as finegraded segregation in sulfides.Sulfide oxidation process study is described. Bacterial oxidation was executed on a pilot laboratory unit using combined autotrophic bacterium: A. thiooxidans , A. ferrooxidans, Leptospirillum ferrooxidans and sulfobacillus thermosulfidooxidation, pH=1,5-2,2, t=28-32?C, oxidation time 120 hours. Pyrrhotite is the least stable sulfide mineral with electrode potential 0,45V versus arsenopyrite (0,55 V) and pyrite (0,55-0,6 V) and is oxidated primarily. Pyrrhotite oxidation is followed by large amount of elemental sulphur, which has a bad influence on cyanidation.It’s established that the rate of arsenopyrite (for the first 48 hours) from concentrate containing 39% pyrrhotite is 2-3 times as less as the rate of arsenopyrite bio-oxidation from concentrate without pyrrhotite. The arsenopyrite bio-oxidation is accelerated only after the elemental sulfur was oxidized by bacterium A. thiooxidans and elemental sulfur percentage was reduced from 6,8 to 3,9%. The bacterium concentration is increased from 2,5x107 to 2,5x109 cells/ml. Almost full oxidation of arsenopyrite (98%) and pyrrhotite (98- 99%) is finished in 120 hours. We have studied two pretreatment methods for elimination sulfur content influence on cyanidation: aeration in lime and electrochemical treatment. Such an operation enables to have supplemental oxidation of elemental sulfur and other oxygen and cyanide absorbants before cyanidation. After treatment the content of elemental sulfur was decreased from 3,9 to 2,2%, gold recovery from 90 to 96% and cyanide consumption from 16,2 to 7,2 kg/t decreases. The content of toxical rhodonite-ions in liquid phase of pulp and disinfection reagents consumption were decreased as result of elemental sulfur content in bio-oxidated product reduction."

Jan 1, 2003

By G. P. Karmakar, K. K. Chandan

"The drilling mud is an essential part of the drilling process, which plays a major role in keeping safe and efficient oil and gas well drilling. In the oil industry, bentonite clay dissolved in water produces the simplest type of drilling muds. Bentonite clay contains montmorillonite particles. These particles are dispersed uniformly in water and such dispersions are used in various industrial products like paints, ceramics, pesticides and drilling muds. The bentonite clay easily dissolves in water and increases the viscosity of the water, which is one of the most important properties of a drilling mud. Bentonite has the highest swelling capacity, which is responsible for building up of the viscosity of the clay-water system. The flocculation behavior of bentonite is one of the major concerns for the performance of the water-based drilling mud in the oil and gas well drilling process. The behavior of drilling mud greatly depends upon the quality and quantity of bentonite clay, as well as the additives that are used in their formulations. In this work, a comprehensive study has been carried out to find out the effect of added polyacrylamide (PAM) polymer, surfactant, pH and salt concentrations on the dispersion/ flocculation characteristics of bentonite clay-water system. It has been observed that the increase in PAM dosage reduces the residual turbidity and improves the settling rate of the bentonite particles. The flocculation rate has also been found to be better under higher pH conditions. The combined effect of salt concentration and PAM dosage improved the overall flocculation efficiency of the system.INTRODUCTIONIn the oil industry, bentonite clay dissolved in water produces simplest type of drilling muds. Bentonite clay containes montmorillonite particles. These particles are dispersed uniformly in water. Such dispersions are used in various industrial products like paints, ceramics, pesticides and drilling muds (Akther et al., 2007). The bentonite clay easily hydrates in water and increases the viscosity of the mud system (Razi et al., 2013; Meng et al., 2012). Bentonite clay in the drilling mud increases the viscosity which is one of the most important prop erties of a drilling mud. Bentonite has the highest swelling capacity, which is responsible for the building up viscosity of the clay-water system (Sonmez et al., 2013). The drilling mud is an essential part of the drilling process, which plays a major role in keeping a safe and efficient oil or gas well drilling (ASME, S. S. C., 2005). The flocculation behavior of bentonite is one of the major concerns for the performance of the water-based drilling mud in the oil or gas well drilling process. This behavior of drilling muds greatly depend upon the quality and quantity of bentonite clay, as well as the additives that are used in their formulations (Yu and Amanullah, 2005; Akther et al., 2007). Bentonite particles form aggregate under certain conditions including high temperature, and high concentration (Luckham and Rossi, 1999). If the quality of bentonite is not sufficient to accomplish intended viscosity of the muds, it is essential to add certain additives to increase the viscosity and prevent aggregation of the system (Razi et al., 2013). The anionic polymer bearing sample can build up inter-particle bonds between the polymer and clay particles. The addition of various additives like, polymers control the dispersion and enhance the viscosity of the mud by controlling the flocculation of montmorillonite particles in bentonite dispersion (Heller and Keren, 2002; Mahto and Sharma, 2004)."

Jan 1, 2018

By Rainer M. Lotzien, Michael J. G. Battersby, Jan Kleefeld, Julian V. Brown, Rainer M. Imhof

"The standard method of separation using flotation is compromised in terms of kinetics and efficiency, because of the generally slow separating differentials of fine bubbles and fine particle suspensions. A new flotation system has been developed that addresses these issues and imparts other benefits. The new technology is based on established pneumatic flotation designs called Imhoflot which use intensive in-line pre-aeration to aerate the flotation pulp prior to its introduction to the separating cell. Consequently the cell is designed only for the separation of the phases and not for bubble-particle contact. In the new system this separation is speeded up dramatically by the introduction of centrifugal motivation in the separating vessel, without the use of internal moving parts. The design focuses on providing increased differential forces on buoyant mineralised bubbles and hydrophilic fines. The observed result of these differential forces is the improvement of concentrate qualities by the reduction of the amount of misplaced material found in the froth. The commercial benefit to industry is much reduced residence time, less than 30 seconds, which offers considerable cost savings in equipment and infrastructure.Prototypes of 0.65m, 1.7m and 2.2m cell diameter size have been constructed for hydrodynamic and industrial scale tests to assess the previously established computational methods for scale up of the process. The 1.7m cell has been installed and operated for cleaning of potash concentrates in Germany, at throughputs of 150 m3/hr, with extremely encouraging results. A 2.2m cell has been installed and operated in plant trials for superfine coal in South Africa. Results are presented that illustrate the effects of differential separations by comparison with conventional pneumatic and mechanical flotation techniques. Predictions of performance are provided in the contexts of the applications tested."

Jan 1, 2003

By Tsvetan Damyanov, Nikolay Hristov, Evgeni Kostadinov, Lubomir Kuzev

"The process of grinding in drum mills is directly dependent on the dynamic forces occuring in the free movement of the grinding bodies in the volume. The subject of discussion are the potential impacts between grinding bodies having different shape and equal weight in a drum mill that has a diameter of 1200 mm. The study utilised ball grinding bodies having a diameter of 120 mm and tetraballpebs having a conditional diameter of 120 mm. The study was carried out using the Solid Works Simulation software. The following cases were examined: • Impact between two identical grinding bodies; • Impact between a grinding body and the shell surface. The study provided numerical values for impact force, kinetic energy of impact, linear speed of impact, linear displacment of the center of gravity and duration of impact deformation. The impact force of the balls is approximately 179000 N. The impact force of the tetraballpebs with typical vertices, edges and spherical surfaces depending on the area of impact is 177000 to 185000 N. Upon impact between two spherical surfaces of tetraballpebs, the contact area is 263.55 mm2, which is more than twice the contact area upon impact between two balls, which is 114.39 mm2. This determines better conditions for the transmission of kinetic energy by reducing opportunities for overgrinding."

Jan 1, 2014

By Rogerio de Oliveira Baldoino

The sedimentary phosphate deposit of Bayovar is located in a very dry area of Peru (desert of Sechura) which is close to the Pacific coast. It consists of seven superposed layers (beds) which call for different strategy of concentration. The ore is composed predominantly by apatite (84% in weight basis) plus silicates (16%). In order to treat the ore from beds 1-5, a suitable standard mineral processing circuit (composed of scrubbing, screening, attrition and desliming) started its operation in 2010, yielding 3.9 Mt/y of concentrate assaying 30% of P2O5. To concentrate phosphate from beds 6-7, however, it is necessary to carry out further cationic reverse flotation of silicates, at neutral pH, to yield a concentrate, which meets market specification. The new process was developed in laboratory scale by a collaborative program conducted between Vale S.A. and the University of Sao Paulo-Brazil. A pilot plant has currently been running in order to confirm the very good results yielded in laboratory scale. The successful accomplishment of flotation in the current beneficiation flow sheet will enable a capacity expansion of 1.9 Mt/y of concentrate assaying 30% of P2O5. As water resources are very limited at Bayovar region, all the steps of concentration, including flotation, must be performed with seawater, which must be continuously recycled. This work addresses some relevant topics related to the use of seawater in the reverse cationic flotation of silicates: influence of temperature, water quality (ageing and chemical composition) and collector type (ether amine versus condensate). The results indicate that condensate amine works better than ether amine. If flotation is conducted with the former collector, the separation process is able to tolerate changes in temperature (25-40oC) and water quality caused by either evaporation or ageing. Keywords: phosphate, flotation, seawater, temperature, ageing, concentration, salt

Sep 1, 2012

By M. I. Panayotova

Some of effluents released by copper smelting plants are highly acidic (pH = 0~1) and contain arsenic and copper in relatively high concentrations (10~20 g/L). Usually arsenic is removed by precipitation with different reagents, such as lime, iron salts, calcium salts, aluminium salts, etc. Precipitates (often voluminous) that require further handling are formed and copper and other valuable components are lost. A method is presented for copper and arsenic extraction from acidic effluents. Effluents are treated in specially designed closed electrochemical cell without chemicals? addition. Gases formed are collected and treated for decomposing the eventual traces of As-bearing compounds and ensuring the environment protection. Initially copper of grade of 85 % is electro-won. Further about half of the initially available arsenic is separated as low-soluble, low volume mixture of intermetallic compounds, oxides and some elemental arsenic. At the next stage the main part of the left arsenic is immobilized as low soluble stable compound. Arsenic content in the treated acid is in the range 0.20~0.25 g/L. Acidity of treated effluent after first two stages remains practically unchanged and the solution can be re-used. Physicochemical and electrochemical processes, governing copper and arsenic removal, are discussed.

Jan 1, 2014

Froth flotation is an industrial process commonly used for the separation of mineral particles. Bubbles sparged in a pulp collect and carry hydrophobic particles to the top layer of a flotation cell, the froth zone. There is a strong correlation between the stability of the froth phase and the flux of solids. However, flotation units placed in series operate, as a whole, in a non-steady state regime with the concentration of particle decreasing from one cell to the next resulting in a decrease in froth stability, which can compromise the recovery of valuables. Organic chemical reagents, frothers, are generally added to prevent fine bubbles from coalescing and to increase the stability of the froth phase. Frothers represent the second largest group of mining chemicals. It is crucial to understand the resulting properties of the frother on the froth phase in order to select the most suitable reagent for a particular operation. The bubble coalescence dynamic of three different surfactants, 1-pentanol, poly (propylene glycol), and tri (propylene glycol) methyl ether, were investigated in this study. In the first stage, the stabilisation mechanism of bubbles in a solution of surfactant was investigated using a specifically designed experimental setup. The coalescence behaviour of bubble pairs was recorded using high-speed video imaging in which information such as the coalescence time and the deformation of the resultant bubble upon coalescence could be extracted. The results were then compared between the different surfactants for several concentrations. It is shown in a study that the coalescence time increases with surfactant concentration until the Gibbs-Marangoni effect is suppressed by bulk diffusion. Conversely, the oscillation of the resultant bubble was found to be affected only at concentrations at which the film is saturated. The implications of the effects of surfactant type and concentration on the coalescence time and bubble oscillation in froth flotation are discussed. Keywords: froth flotation, frother, bubble coalescence

Sep 1, 2012

By Yuri L. Nikolaev

The treatment of placer gold with fine gold, associated with gold-bearing sulfide minerals, heavy minerals and oxidized minerals such as manganowolframite (gubnerite) is not an easy task. In this case, this complex material cannot be treated using physical separation methods such as deep concentration and finishing, magnetic separation and solvent extraction. This technology is usually employed in gold washings finishing plant. The easiest way to recover precious metals in the form of an easy-to-sample saleable product is metallurgical treatment. This paper describes the application of pyrometallurgical processes with oxidative roasting, re-cleaning of cinders (if required) and ore-thermal smelting for producing gold bullion. Hydrometallurgical treatment of slags as an additional operation is recommended in order to maximize recovery of valuable metals. After this treatment, a barren leaching cake rich in PGM can be sold in the market. PGM can be collected as gold-silver alloy during smelting which allows the phase formation of polymetallic matte due to specific composition of fluxes. The PGM are then in the form of saleable gold bullions in the refinery.

Sep 1, 2012

By S. Mohanta

In composite washeries optimization of operating parameters to achieve maximum clean coal yield at the desired clean coal ash level is a major problem. This problem is more acute in countries like India, which have predominant reserves of difficult-to-wash coals. The constrained operational parameters of washing for some equipments make it more severe. In addition to this, the dependence of separating performance of different equipments upon various variables aggravates the situation. Here an attempt is made to find a numerical solution to get maximum yield and minimize the difference between the actual and the theoretical yield. The solution is arrived through constrained non-linear optimization of a multivariable objective function that utilizes spreadsheet tools; the method accommodates any number of source coals or washing size fractions. By using a designed Ep value the predicted yield of composite clean coal has been calculated and the yield is optimized subject to constraints on both the ash and specific gravity. It is shown that operational constraints of different washeries in the composite plant that utilizes gravity separation methods can also be over-come. The technique offers the coal preparation engineer an effective and straightforward method for determining the optimum cut-points of separation for different coals or blended coals to obtain maximum product yield at a specified level of ash content.

Jan 1, 2014

By S. Q. Zhu

A newly developed coal flotation collector ZFC and its flotation characteristics for five different coals were introduced in this paper. ZFC is an emulsion composed of 27% diesel oil, 70% water and 3% surfactants. The main surfactant is synthesized with oil which is environmental favorable and reproducible. Compared flotation experiments show that, at the same dosage, ZFC give 2%~5% recovery promotion than typical collector with only a slightly ash content increment, but saving 70% diesel oil. Zeta-potential and Wetting heat measurement indicate that the surfactant helps the interactions between oil and coal particles, the industrial application tests in several coal preparation plants demonstrate that ZFC is suitable both in technical and economical aspects.

Jan 1, 2014

By O. N. Mohanty, S. Mohan Rao, N. D. Rao, T. Mukherjee, P. V. T. Rao

"Chromite ore is an indispensable raw material in the manufacture of ferro-chrome and charge-chrome, which are used for the production of stainless and other alloy steels. The demand for chromite ore is ever increasing because of increasing consumption of these steels. Keeping this in view, Tata Steel is keen to recover values from fines and wastes, and also to produce value added products from their captive chromite mines and its processing plants.Tata Steel has its captive chromite resources at Sukinda, Orissa. They contain two ore types, i.e. (i) Ferruginous and (ii) Siliceous. The generation of off-grade ores is an increasing trend and simultaneously customer quality requirements are becoming ever more stringent. The ferruginous type ore also contains a considerable quantity of in-situ fines (~20% particles below 0.5 mm) that compound the beneficiation problem.In many places, in India and abroad, mined non-marketable off-grade and low grade chromite ores are upgraded by using either simple classification techniques like screw classification, hydrosizing, hydrocycloning or conventional gravity concentration processes such as Heavy media separation, Jigging, Spiraling, Tabling etc.At Tata Steel, the ferruginous type ores are treated in Chrome Ore Beneficiation (COB) Plant that comprises: a crushing and grinding circuit; a classification circuit using hydrocyclones; and a beneficiation circuit using 4 stage spirals in the coarse circuit (-0.5+0.1 mm) and 3 stage spirals & tables in the fine circuit (-0.1+0.038 mm). In this process, 3 types of tailings are being generated and together analyses about 17 % Cr2O3, which is high. From the present operation the chromite recovery is around 70% and could not produce coarse concentrates (+0.5 mm size). Whereas the siliceous type ore is treated in the Lumpy Ore Processing (LOP) plant, consisting of crushing-washing & classification-hand sorting operations, to produce marketable grade lumpy ore and –10 mm de-slimed fines. These fines are intermittently treated in the COB plant. The higher silica content (greater than 1%) and low Cr/Fe ratio (less than 2.8) are the problems with these concentrates."

Jan 1, 2003

Calaverite is a gold telluride found in the Kalgoorlie region, Fiji, Cripple Creek Colorado and numerous other locations. It is known that a high pH is necessary for calaverite cyanidation, with the leach rate increasing substantially above pH 12 due to the hydroxide ion concentration. In most circumstances lime is used to achieve high pH, however lime saturates at approximately pH 12, limiting the maximum pH obtainable in a critical region for calaverite leaching. Plant observations, laboratory experiments and thermodynamic modelling show that the maxi-mum hydroxide ion concentration that can be achieved with lime (CaO) is strongly dependent on common ions. The presence of calcium, as commonly found in saline waters, substantially diminishes the maximum pH that can be obtained with lime. Conversely the presence of sulfate ions, as generated through oxidation of sulfides, substantially increases the maximum pH that can be achieved with lime. Sulfide oxidation during cyanide leaching of complex ores may generate acid and sulfate ions, making overdosing with lime at the front of the circuit, or staged addition down the leach train, important to maintaining the maximum hydroxide concentration.

Jan 1, 2014

By S. K. Pan, M. P. Srivastava, N. Prasad

"Dalli mines of Bhilai Steel Plant, India is fully mechanized iron ore mine having wet processing system. It has a capacity to treat 5 Mt of ROM. In processing circuit of Dalli mines, scrubbing, wet screening and classification operation is being carried out. Average slime generation for the last five years is about 14% of ROM. As the mining has reached to the lower benches, fines generation is more. As a result, very fine and heavy particles, which settle fast, are being discarded with the slime to tailing pond. These heavy and faster settling particles were causing jamming in the thickeners.Laboratory investigations were carried out at Research and Development Centre for Iron and Steel (RDCIS) to suggest a suitable scheme to recover high quality fines so that the availability of thickener can improve. The slime samples were first treated in a floatex density separator. The concentrate obtained from the floatex density separator was treated in hydrocyclone. Laboratory investigations indicated that the slime with 49% Fe, 12.7% silica and 10.7% alumina can be upgraded to 62.1% Fe, 3.3% silica and 2% alumina with 36% material recovery. Based on the laboratory studies ,a system was installed at Dalli minesThe general arrangement of the system is shown in Fig. below."

Jan 1, 2003

By Victor Avdokhin, Valery Morozov, Valery Stolyarov

"The adaptation-determination method provides for keeping given relationship between concentrations of ionic and molecular components of a pulp liquid and correction of parameter of the model on the basis of analysis of ore composition, technological parameters of flotation, and cost of valuable components.• optimisation program “ADDEFLOT” and combined analyzer of pulp “RA-931”An adaptation-determination method provides for two-level control of bulk and selective flotation of polymetallic ores. The lower level provides for control of reagent dosing on the base of control of ionic composition parameters in the pulp liquid phase. The control goal is to keep the basis relationship among parameters of ionic composition (ions A, B, C) in pulp liquid phase given by equations of type:• alg[A] + blg[B] + clg[C] = K (1)Values of a,b,c coefficients are uniquely determined by a physico-chemical model used. Kind of the model depends on mineral composition of an ore and reagent regime applied. As parameter of ionic composition, also values of one or two parameters (or their combinations) can be used, for instance, pH, concentration of sulfide ions, ions of collector.The upper level of control is based on calculation and use of technological results of selective flotation. At the level, an adaptation of the model (1) is conducted. A principle of the adaptation is in determining (and including in pre-setting function of the lower level) such value of K parameter, at which maximal economic effectiveness of the process is reached. As a criterion of economic effectiveness of the process, a function of losses of several valuable components, taking into account cost of the metals lost, is used. For 2-component ore, in simplified form, the function is as follows:"

Jan 1, 2003

By G. Jenny

The particle size distribution of ground minerals is of decisive importance for downstream processes like floatation, separation, drying or others. In order to optimize the process efficiency on one hand and the final product quality on the other hand an early control of the grinding or classification stage is essential. The ultrasound based particle size analyser OPUS is capable of performing on-line particle size distribution (PSD) and solid content measurement of mineral slurries such as iron ore, copper ore, fluorspar, or quartz sand and alumina directly in heavy and rough process environment. The instrument provides a PSD of 31 size classes and can be applied for particles from nanometer range up to several millimetres. Arbitrary interpolations in between the 31 measured points are available. Typical residue values show an excellent agreement to off-line particle size analysis methods such as e.g. sieve analyses or laser diffraction. OPUS is designed as rugged in-line probe made from stainless steel. The applied technique is independent of product flow dynamics, contamination, optical properties, vibrations, pressures or changes in solid concentrations. The instrument provides all data on the system?s PC or on the process control system by a variety of interfaces.

Jan 1, 2014

By X. W. Zhang

Mica plate is broadly used in electric industry, production of man-made mica paper plate is in-creasing. The problem coming with is that large quantities of leftover materials unable to be re-cycled are produced during cutting and molding of mica plate productions. The leftover materials are always abandoned as crabs, which not only pollute the environment but also waste our resources. The study intends to find a new measure to decompose and to reuse the mica plate leftover materials so as to create a new production process of mica plate, which is clean and does not produce crabs.

Jan 1, 2014

By M. Unesi, S. Haj Mohammadi, M. R. Abdoli, M. R. Garmsiri

"Hydrocyclone-thickener circuit is a promising solution to enhance the dewatering efficiency in mineral industries. The challenges in the circuit is reducing particle size in the thickener feed and the good feature is a rise in the retention time of sediments in the thickener. In this work, the effect of particle size, bed depth and residence time on the thickener performance were investigated. In this order, pilot scale columns were employed at Sarcheshmeh and Shahrebabak copper complexes. Furthermore, the influence of residence time was differentiated due to the variations in the bed depth and settling flux. Moreover, a new approach was introduced to estimate solids residence time in the thickener. results indicated that with smaller particles that are introduced to the column, the bed density as well as thickener discharge solids concentration dropped significantly. It was found that thickener discharge solids concentration fell from 59.6 to 33.8 % with reducing particle size from 130 to 22 µm in the settling flux of 20 t/m2/day. Additionally, it was found that longer residence time and deeper bed resulted in an increase in the thickener performance while the bed depth has a stronger effect. It was proved that employing a hydrocyclone prior to the thickener resuted in an increase in the dewatering efficiency.INTRODUCTION Thickeners are widely employed in mineral industries to recycle tailings and concentrate water content. A limited fraction of suspension water content is recycled using a thickener. For instance, about 50 percent of tailings water content could be recycled using a shallow bed thickener during copper processing. Since the scarcity of global water resources became more serious, the demand for improving dewatering efficiency in mineral industries became more significant [1]. A number of solutions were recommended to enhance dewatering efficiency of thickeners including optimization of current thickeners, employing deep bed thickeners and utilizing thickener-filter or hydrocyclone-thickener circuits. Optimization of existing thickeners is essential, however, it does not meet the significant demand for recycled water. The application of deep bed thickeners (known as paste thickeners) has been rising in the mineral industries [2] due to a higher dewatering efficiency while its costs is remarkable."

Jan 1, 2018

By A. Shandilya

ACC ECOSAND is finely powdered crystalline silica, which can replace natural sand usage in concrete and plasters. ACC ECOSAND ensures a comparatively denser concrete than those made only with natural sand and / or quarry fines / Manufactured Sand (Artificial Sand). Moreover, there is a significant gain in compressive strength (10-15 %) & durability in concretes (Reduced chloride conductivity leads to increased durability). ECOSAND is a by-product of froth flotation of limestone. At ACC Madukkarai cement works, Coimbatore, Tamilnadu, full-fledged mineral beneficiation process is adopted to enhance the usage of flotation reject in concrete and plasters. Optimum level for usage of ECO-SAND is 50%. With 50% usage of natural sand+50% ECO-SAND in concrete mix, 1 day, 3 day, 7 day & 28 day compressive strength is increased by 30.1 %, 22.6 %, 15.1 % & 11.0 % respectively and with moderate chloride permeability as compare to 100% Natural Sand. Keywords: froth flotation process, beneficiation studies, Denver cell, ECOSAND, siliceous material, durability & compressive strength, RCPT

Sep 1, 2012