Search Documents

By P. M. Solozhenkin, V. P. Nebera, V. D. Skorohodov

"Aqueous dispersions of air specifically prepared on the basis of flotation reagent solution acquire active properties in relation to the solid surface and may be imply as a medium for flotation ores. Such aerated solutions were defined as Activated Aqueous Dispersions of Air (AADA) with 5-6:1 ratio and the procedure of mineral separation was defined as a flotation process under non-equilibrium conditions. These procedures differ from conventional flotation mainly in reagent interaction with minerals through their adsorption films on gas bubbles simultaneously forming flotation complexes. Gas-liquid mixture is kept till an adsorption layer of reagents close to the limit value is formed on the surface of bubbles. The theoretical basis of AADA is considered.The results of two-phase gas- liquid mixture (AADA) were studied. Two versions of AADA were considered. Electrical surface potential of the air bubbles with the surfactant film, untreated minerals particles in Coulomb attraction and flotation complex formation were analyzed. Special flotation machines were constructed for separation of mineral suspension in air dispersion, whose effectiveness was confirmed in flotation of apatite waste of Kovdor ore. FK-9 machine introduced on Kovdor iron ore combine for the recovery of apatite from current departures of factory. The froth product contained 7.2 % P2O5, with recovery of 44 % apatite, which was processed for getting melted phosphoric-magnesium fertilizers."

Jan 1, 2003

By Aziza A. Yousef, Suzan S. Ibrahim, Mahmoud A. Arafa, Mohamed A. Abdel Khalek

Due to the shortage of fresh water in the Middle East, seawater has been used as an alternative in flotation beneficiation. The flotation process requires about 7 m3 of water/mt ore. This article aims to study the effect of seawater cations and anions on the flotation. Natural pure francolite, calcite, dolomite and quartz were characterized by chemical, thermal and x-ray diffraction analyses, surface area, solubility and zeta potential. Synthetic seawater was prepared with the major chemical composition similar to natural seawater as follow; 2.45% NaCl, 0.52% MgCl2, 0.41% Na2SO4, 0.116% CaCl2 and 0.07% KCl. Also, natural seawater was used in application. The point zero of charge was estimated at pH 6.5, 7.8, 9.2 and 2.2 for francolite, calcite, dolomite and quartz, respectively. Calcium ions were released from the three minerals with Mg2+ and P2O5 3– released from dolomite and phosphate, respectively. The adsorption of collector, zeta-potential and floatability of pure minerals were studied. The effect of individual cations and anions predominant in seawater are studied on individual mineral or group. The troublesome Ca2+ and Mg2+ ions should be controlled by soda ash addition. Sodium silicate improved the selectivity of mineral mixtures and natural ore. At optimum conditions the calcareous phosphate ore yielded a concentrate of 34% P2O5, at 83% recovery with 0.61% MgO, from an ore assaying 25.3% P2O5 and 9.4% MgO. To minimize the Clcontent, fresh water of about 0.5 m3 /t was used and the Cl- decreased to about 0.09 %

Jan 1, 2003

By Yury V. Kulikov, Rakan Rahbani, Arkady Y. Senchenko

"The relevancy of complex minerals treatment is constantly increasing taking into account mineral resources depletion. Different refractory ores and concentrates, oxidized and polymetallic ores, as well as metallurgical products (slags) can be assigned to such mineral type. The treatment of such products via conventional flowsheets requires considerable capital and operational costs and does not always provide high recovery level of valuable components into a saleable product. Therefore, considerable amount of ores and metallurgical products are not treated, or treated inefficiently. One of the most promising approaches that allows economic treatment of refractory products is their ultrafine grinding down to 5-20 µm with subsequent processing or hydrometallurgy. Horizontal bead mills - the IsaMillTM, developed by Xstrata Technology, received their wide application in mining industry. Standard testing is performed under laboratory conditions in an M4 IsaMillTM (volume - 4 liters) to define the parameters of fine grinding. This mill completely simulates the operation of full scale industrial mills up to 50 m3 in volume (up to 8000 kW motor). The paper describes fine grinding technology performed in bead mills, and the importance of testing according to a certified method for industrial equipment selection. The paper contains description of promising directions of fine grinding technology application for several projects in Russia and Kazakhstan."

Jan 1, 2014

By Brian Lindner, Lidia Auret, Niel Knoblauch

In this paper, a fault detection and identification framework based on feature extraction and topology extraction methods is proposed, and evaluated on a simulated base metals refinery high pressure leaching process. Feature extraction methods included linear and kernel principal component analysis, while process topology information was extracted with linear cross-correlation, partial cross-correlation and transfer entropy. Connectivity maps were constructed to identify possible fault propagation paths to aid root cause analysis. The results indicate that process topology can enhance the fault identification capability of data-based process monitoring methods. The study of the considered base metals refinery pressure leaching process is ongoing, with future work including the creation of a fault library which would lead to further critical evaluation of the proposed fault detection and identification framework.

Jan 1, 2014

By K. V. Fedotov, E. V. Zelinskaya, O. V. Ulanova

"Mining enterprises, in particular, those on the territory of the Siberian platform, produce large amounts of pumped water, which cannot be recycled because of its high mineralization and, thus, is discharged as liquid waste either back into the ground or onto the surface. However, groundwater is often a valuable raw material and a source of useful chemical substances. Brines are unique groundwaters. In the current environmental and economic situation, the huge loss of natural raw materials and their deliberate conversion into wastes is unaffordable. The exploration of non-traditional sources of minerals such as the hydromineral resources (including pit water) is a matter of rational nature management. The industrial value of brines of the Siberian platform is due to the high contents of rare alkali and earth alkaline elements (lithium, rubidium, cesium, strontium, bromine, etc.). The absolute concentrations of these elements in brines are tens of times higher than the lower limits of the mining cut-off. The long-term data analysis was performed to estimate the environmental impact of liquid waste from two mining enterprises, namely, Korshunovskii (Irkutsk region) and Udachnaya (Southern Yakutia). The study was focused on the prospects of hydromineral resources as non-traditional sources of valuable elements and the exploration of technological processes for the selective extraction of rare alkali and earth alkaline metals from natural multi-component brines aimed at decreasing their negative environmental impact. The environmental and economic efficiency was proved for the processing of complex brines and the integrated selective extraction of rare earth metals from sodium chloride brines of the Korshunovskii plant and calcium chloride brines of the Udachnaya plant based on the ion exchange sorption, eluent chromatography, flotation, crystallization, and freezing techniques. The basic technological schemes were developed for the metal extraction from pit water and brines.INTRODUCTION In the Irkutsk region (the Angara–Lena artesian basin) and in Yakutia (the Olenek and Tunguska artesian basins), several mineral deposits are developed and, incidentally, aquifers bearing brines of different types are opened, which are eventually converted into liquid production waste (Rusetskaya et al., 1994) This raises the issue of the burial or utilization of brines since their use within the water circulation is impracticable under the existing technological conditions while their discharge into the surface watercourse is unacceptable because of the harmful environmental impact."

Jan 1, 2018

By Stoyan N. Groudev, Ioannis Paspaliaris, Irena I. Spasova, Kostas Komnitsas

"Acid mine drainage waters generated in the uranium deposit Curilo, western Bulgaria, were treated by means of a constructed wetland located in the deposit. The waters had a pH in the range of about 2.5 - 4.1 and contained uranium, radium, some heavy metals (iron, manganese, copper, zinc, cadmium, cobalt, nickel, lead), arsenic and sulphates in concentrations much higher than the relevant permissible levels for waters intended for use in the agriculture and/or industry. The wetland covered an area of about 140 m2 and was characterized by an abundant water and emergent vegetation and a diverse microflora. Typha latifolia, Typha angustifolia and Phragmites australis were the prevalent plant species in the wetland but species of the genera Juncus, Eleocharis, Scirpus, Carex and Poa as well as different algae were also well present.The water treatment was started in July 2001 and until now (August 2002) the wetland effluents were characterized by pollutants concentrations decreased below the relevant permissible levels. The water flow rate through the wetland during this period varied in the range of about 0.2 - 1.0 l/s. The water clean-up markedly depended on the temperature but was efficient even in the cold winter months at air and water temperatures close to 0oC. The removal of pollutants was due to different processes but the microbial dissimilatory sulphate reduction and the sorption of pollutants on organic matter (viable and dead plant and microbial biomass) and clay minerals played the main role. Negative effects of the pollutants on the growth and activity of the indigenous plant and microbial communities were not observed."

Jan 1, 2003

By Jussi Liipo, Pertti Lamberg

Image analysis of process samples gives precise data on particles and their composition. The results presented as liberation tables and maximum grade-recovery curves are informative and good for comparing different feed materials, but basing on them it is impossible to predict the results of the mineral separation process (flotation, magnetic separation, gravity separation) in details. The exact and extensive particle data has remained large unused, because there has not been a model nor a modeling program to include particle information in mineral separation processes. This study introduces a method, which incorporates the particle data in the kinetic model of flotation. Similar approach can be used in modeling other separation processes, too.

Jan 1, 2003

By Gauti Asbjörnsson

Material handling is an essential part of the aggregate and mining industries. Mixing and blending of granular material can affect the grading and particle size distribution of the material leaving the system. Segregation and variability can cause problems in the downstream process while insufficient capacity will disturb upstream processes. Process plants utilize surge bins for handling recycle streams of material and act as a buffer for the process. The flow through the surge bin is usually controlled by a simple PID controller or PID controller in combinations with a plant-wide controller. Even though the surge bins play an important role of smoothening out the plant and creating a steady operating condition they are seldom included in plant simulations. This can lead to a number of problems in the form of decreased plant capacity, plant lockdown, and even operation units malfunctioning. The main objective of this study is to investigate the dynamic behavior in surge bins and develop a model more suitable for representing this behavior, which can occur during operation, for dynamic simulations. The proposed model adopts vertical layers which allow for flows between segments depending on the level of neighboring segments. This enables both the representing of segregation within the system and gives an indication on the effects from different inlet- and outlet placements. The proposed model was developed in MATLAB/Simulink and validated against an actual bin with the total capacity of 660 m3 in platinum ore application. With the new bin model significantly higher fidelity and more accurate dynamic, simulation results were achieved. Keywords: dynamic simulation, modeling, segregation, material handling, MATLAB/Simulink

Sep 1, 2012

By Rhulani F. Maluleke, Francis W. Petersen, John H. Marsh, Johann de T. Steyl, Allan Nesbitt

"Pressure leaching of chalcopyrite and nickeliferrous pyrrotite at temperatures between 105 and 200 ºC has been proposed as a potentially viable route for the extraction of mineral elements from sulphide concentrates. In general, these concentrates contain iron, and the economic success of the processes is partially dependent on the choice of the environmentally acceptable iron-removal technique. One of the most widely used methods for the removal of iron from sulphate liquors is precipitation as hematite, goethite, or jarosite. The nature of the iron precipitate formed dictates downstream dewatering and residue treatment and disposal options. However, a better understanding of iron precipitation under the defined process conditions would consequently be of benefit in process design and optimisation.This study investigated the precipitation of iron in the autoclave at temperatures between 105 and 200 ºC. The effects of temperature, acid concentration, iron concentration, and the presence of other metal cations on the nature and composition of the precipitates were determined."

Jan 1, 2003

By D. J. Borrow, K. van Netten

"A fine coal tailings feed was selectively agglomerated using a concentrated water in oil emulsion binder consisting of 95% aqueous phase and 5% organic phase. The purpose of the study was to investigate a continuous system in plug flow, providing a rapid beneficiation technique with high selectivity and recovery. The development of the novel binder was undertaken in previous work in a batch system consisting of a high-speed blender. In this previous work, it was found that agglomeration could be achieved in 3 s, providing the binder was pre-dispersed. Furthermore, it was found that, depending on the feed, only ~1 wt% of oil was required to achieve agglomeration, some 10 times less than required in traditional oil agglomeration. In a more recent study, the technique was adapted into a continuous process. Due to the rapid speed of the process using the emulsion binder it was found that a simple flow constriction within a 1 inch pipe was sufficient to achieve the selective agglomeration observed in the batch system. In this previous study, a coal feed consisting of a flotation product was agglomerated at a superficial slurry velocity of 1.3 m/s using a partially closed ball valve as the flow constriction. In the current study, a feed consisting of fine coal tailings with an ash content of 50.1% was used to establish the influence of superficial slurry velocity on the agglomeration process. The superficial slurry velocity was varied between 1.3- 4.2 m/s, while maintaining a constant pressure drop of 100 kPa across the flow constriction. The flow constriction consisted of a partially closed ball valve. It was found that increasing the superficial slurry velocity across the flow constriction reduced the amount of organic liquid required to achieve agglomeration. Under the optimum conditions, a combustible recovery of 80.4% was achieved at a product ash content of 9.6%. This work demonstrates a valuable product can be rapidly produced from tailings material using the novel emulsion binder. INTRODUCTION A significant opportunity exists to recover fine coal from material that is currently classified as waste. This waste material, also called tailings, is currently considered not economic to process due to its high ash content, low solids concentration, and the fine size of the particles. Thus, for this opportunity to be realised, a process is required that is highly selective and has the ability to economically recover fine particles at high throughputs. The technique of oil agglomeration has previously been considered as a candidate for the recovery of fine coal, as it is highly selective and has no lower limit on the size of particle that can be recovered (Capes and Jonasson, 1989). However, the cost of the oil required as the binding agent in the process has proven to be a significant barrier to any long-term applications (Swanson, Nicol, and Bensley, 1977). Recently, however, Yoon and co-workers have developed an ultrafine coal separation process that utilizes an oil phase for the recovery of the hydrophobic coal particles and have implemented an oil recycle to greatly reduce the consumption and thus cost of the oil (Yoon et al., 2016)."

Jan 1, 2018

By M. F. He

The depression of pyrite in marmatite flotation by a new depressant Sodium Glycerine-xanthate (SGX) has been investigated through microflotation, zeta potential, and adsorption measurements in systems open to the atmosphere. The flotation tests of single mineral show that in the presence of SGX, marmatite can be activated by Cu2+ and shows good flotability, while pyrite can?t be activated and therefore shows poor flotability, as a result these two minerals can be separated using butyl xanthate as the collector. The depression mechanism of SGX on sulfide minerals is discussed based on Zeta potential and adsorption isotherm. Zeta potential experiments demonstrate that at the presence of Cu2+, SGX can strongly adsorb on the surface of pyrite, while it can?t adsorb on the surface of marmatite, thus the results are in accordance with those of flotation experiments; the results of adsorption isotherms show that the adsorption density of SGX on pyrite is greater.

Jan 1, 2014

By H. Lieberwirth, M. Hesse

"Selective comminution (SC) is beneficial for the treatment of primary raw materials, especially if it is utilized in the pre-concentration process. Pre-concentration processes are applied in mineral processing to relieve subsequent processes and to achieve a higher efficiency. SC is also a promising method for the treatment of low-grade ores and waste dumps. With SC, various components can be separated such as valuable minerals from waste, ore from wall rock and different ore varieties within a deposit. SC is a property of a comminution system and leads either to a preferred crack propagation in one component (called preferential breakage) or to a preferred crack propagation along the grain boundaries (called interfacial breakage). SC results from different comminution behavior of various components in the feed material. For mechanical comminution, the preferential breakage seems to be the most important case of SC. Hereby SC generates only the difference in the particle size which can finally be used as a sorting parameter. A sorting process which uses SC depends on three parts: the feed material, the comminution machine and the separation machine. The feed material defines the potential for SC. Differences in properties like strength, toughness and density which are related to comminution are often used. The comminution machine has to exploit this potential. The extent of the exploitation can be influenced by the machine design, material and operational parameters. After SC, the various components are still combined in the product. So ultimately, a separation machine is needed. At preferential breakage, a simple screening machine can be used. The basics about SC will be presented at first. This contains relationships between material properties, the kind of loading in the comminution machine and the SC effect. These basics can be used for example to exploit a potential to SC for a pre-concentration step or to avoid the SC for a higher efficiency of subsequent processes. Based on recent investigations with impact load, the influence of the important parameters compressive strength, density, particle size and impact velocity to the SC will be shown, using examples of lead-zinc ore comminution and fluorspar processing."

Jan 1, 2018

By Thomas Mütze, Michael Klichowicz, Mathis Reichert, Holger Lieberwirth

"Self-similarity is proofed to be a common feature when brittle material is comminuted, either in particle bed or single particle mode. Appropriate test work is well documented for particle sizes less than 7 mm in several publications. In contrast, almost no research has been done for coarser particles. The aim of this paper is to show that the fracture pattern of coarser material also tends to be self-similar. Hence, single particles of quartzite, granodiorite and dolomite were comminuted under compressive load. The focus was set on three different size fractions -3.15 +2.5 mm, -31.5 +25 mm and lumps -300 mm. According to the wide range of particle sizes, three different piston-die presses were used with a maximum compressive force ranging from 5 kN to 4000 kN. The force-displacement curves were recorded in order to calculate the specific comminution energy. Additionally, the -31.5 +25 mm size fraction was crushed in a laboratory scale jaw crusher and a roll crusher. Some authors report that the energy-size-reduction relationship of self-similar materials can be approximated by a linear function, which is independent of the comminution equipment. In their charts the slope can be seen as a product-size-independent grindability measure. Our tests show a self-similar breakage behavior when particles in a range of -300 +3 mm are comminuted in single particle mode. Furthermore, the products of the piston-die-presses and the roll crusher are similar to each other in a self-similar representation of the particle size distribution. The jaw crusher product, however, is not self-similar compared to the piston-die-press products. Finally, the linear energy-size-reduction relationships are confirmed for each fraction, but show size dependent slopes."

Jan 1, 2014

By Venkataramana Runkana, Shantanu Maheshwari

As the world reserves of high quality ores are getting depleted at a rate higher than ever, the liberation of valuable minerals from low grade ores is becoming more and more relevant and imperative. But, liberation of minerals from low grade ores requires grinding of ore to extremely fine sizes. High energy milling in a planetary ball mill is one such option where one can produce particles in the nano-meter range. Although planetary mill is employed extensively for ultrafine grinding, dynamics of grinding inside the mill is not fully understood because of the dependency of grinding kinetics on many interconnected phenomena like collisions between media, particles and wall, time dependent rheology, adsorption and desorption of dispersant, abrasion of media, agglomeration of particles, etc. It was well articulated in literature that media motion and number of media collisions have strong effect on grinding kinetics and final product size distribution. Simulations were carried out using the discrete element method (DEM) to compare the performance of a planetary mill with a ball mill, with and without lifters, in terms of impact energy and number of collisions and it was found that number of collisions is considerably high in the planetary mill. The high number of collisions might be the reason for production of ultrafine particles in the planetary mill. We have also fitted a population balance model (PBM) to experimental data from a laboratory scale planetary mill for prediction of particle size distribution. Unlike previous models, we have incorporated functional forms for the selection function and the breakage distribution function so that the number of parameters in the PBM is just five. The predicted product particle size distributions at different grinding times are in reasonably good agreement with experimental data.

Jan 1, 2014

By A. E. Sobolev

The kinetics of hydrochemical oxidation of antimonite in solutions of nitric acid was studied using the rotating disk method and the factor experiment design. The dependences of the antimonite?s oxidation rate on concentration of nitric acid solutions, temperature, disk rotation frequency, and duration of interaction were determined. The adequate kinetic models allowing calculating the specific oxidation rate at any combination of the values of the influencing factors were obtained. The oxidation process is found to proceed in a mixed mode, close to chemically controlled. Gradually, as the sediments of elemental sulphur and Sb2O5 accumulate on the disk surface, the process becomes controlled by internal diffusion. The observed high (more than second) order of the oxidation rate with respect to the concentration of nitric acid was explained by the autocatalytic action of the acid reduction products. The apparent activation energy depends on the stage of interaction. At the initial stage (in a mixed mode of the process proceeding), it depends on nitric acid concentration and varies from 31.5 kJ?mol?1 (in 2 M HNO3) to 36.1 kJ?mol?1 (in 10 M HNO3). This trend indicates the weakening of diffusion limitations with a nitric acid concentration increase. When the process is controlled by internal diffusion, the apparent activation energy was found to be 14.5 kJ?mol?1. The obtained kinetic characteristics enlarge the database on hydrochemical oxidation kinetics of sulphides and can be used for the elaboration of the recommendations for the effective comprehensive exploitation of antimony-bearing ores and concentrates.

Jan 1, 2014

By D. W. Feng

Thiosulfate leaching has been considered as the most promising alternative to cyanidation for the recovery of gold from ores. The chemistry of the ammonia-thiosulfate-copper system is complicated due to the simultaneous presence of complexing ligands such as ammonia and thiosulfate, the Cu(II)-CU(I) redox couple and the stability of thiosulfate in solution. However, acceptable gold leaching rates can be achieved by maintaining suitable concentrations of thiosulfate, ammonia, cop-per and oxygen in the leach solution. The leaching of gold in thiosulfate solution is an electrochemical reaction involving the oxidation of gold to gold thiosulfate and the reduction of Cu(II) to Cu(I). Previous studies have shown that the reaction rate of gold was much higher in the presence of am-monia thiosulfate than corresponding sodium thiosulfate. This indicates that cations may affect the anodic oxidation of gold in thiosulfate solution. The present study utilises electrochemical tech-niques to study the anodic oxidation of gold in thiosulfate medium in the presence of the different alkali metal and alkaline earth metal ions. It has been shown that the presence of the heavier cations such as potassium, calcium, and caesium enhance the oxidation of gold in thiosulfate solution. Leaching tests also indicated the improved recovery of gold from a sulfide ore with the addition of heavier cations. XPS results demonstrated that the binding energy for gold shifted to lower values in the presence of the heavier cations, indicating the ready formation of ion-pair with gold thiosulfate at the gold surface during adsorption.

Jan 1, 2014

By Alan Bax, John D. Lewins

"Platinum Australia Limited (“PLA”) is currently undertaking a Feasibility Study into the development of the Panton Platinum Palladium Project located in the Kimberley region of Western Australia. The Panton Intrusive is a layered, differentiated mafic to ultramafic structurally complex body that has undergone numerous folding and faulting events. This has resulted in a southwesterly plunging synclinal structure some 10 kilometres in length and 3 kilometres wide.High grade PGM mineralisation is hosted within a number of stratiform chromitite reefs within the ultramafic sequence. The focus of the Feasibility Study is on the Top Reef which is situated approximately 150 metres below the mafic/ultramafic interface. The average true width of this reef is approximately 1.2 metres and the reef has a defined resource is 10.1 million tonnes at an average grade of 6.1 g/t PGM + Au.The Palladium to Platinum ratio of the Top Reef is approximately 1.15:1 and the reef also contains an average of 0.4 g/t Au and 0.3 g/t other PGM’s. The Panton ore is considered refractory in nature and standard flotation techniques achieve a PGM + Au recovery of less than 65% with a concentrate grade of less than 100 g/t PGM + Au. As part of the Feasibility Study Platinum Australia in conjunction with their major shareholder Lonmin Plc developed a new metallurgical process which has achieved an overall PGM + Au recovery of approximately 80% into a high grade PGM concentrate which is suitable for feeding direct to a PGM refinery.THE PANTON PROCESSThe Panton Process incorporates a two-stage Milling and Flotation circuit with no cleaning stages to produce a low grade, high recovery flotation concentrate. Typically the concentrate mass constitutes 25% of the feed and has a PGM + Au grade of 25 g/t.This low-grade concentrate is subjected to calcination in a rotary kiln or fluid bed at a temperature of approximately 400 0C for a period of 60 minutes. This step is designed to render the platinum minerals soluble in cyanide and both the temperature and the duration of calcination are critical to the efficiency of the leaching process."

Jan 1, 2003

By Tom Liu

This paper is a fundamental study of bubble-particle collision efficiency in turbulent flows. A CFD-based microscale scheme for the prediction of turbulent bubble-particle collision efficiency in a 3D isotropic turbulent flow is developed, and in this way, turbulence effects on particle-bubble collision efficiency are taken into account for the first time. By comparing the computed results with experimental data from the literature, the CFD simulation is shown to correctly predict the bubble-particle collision efficiency in a quiescent environment. The CFD method was then applied to the investigation of bubble-particle collision efficiency in a turbulent flow, and the simulation results are shown to be qualitatively consistent with the real observations. The predicted collision efficiency can be used in a multiscale modelling scheme, which would account for all control variables in a flotation cell, such as impeller structure and tip speed, air nozzle structure and air flow rate This study indicates how microscale simulations of bubble and particle behaviours, coupled to macroscale CFD simulations of flotation cells, can provide a powerful tool predicting the flotation rate in a real flotation cell.

Jan 1, 2014

By W. Z. Yin

With increasing of mining depth, many iron ores in Liaoning Province contain carbonates such as siderite and ankerite. The emergence of these carbonates in ores creates a fatal impact on the running producing process of anionic reverse flotation in Dong Anshan Sintering Plant, which leads to ?concentrate and tailing no separated?. And its reason is still unknown. Moreover, siderite, despite that its ferric theoretic grade is only 48.2%, however, do not affect the blast furnace utilization factor, therefore, can be used as raw materials in ironmaking. In order to solve the separate problem of iron ore containing carbonates, five pure minerals, martite, magnetite, quartz, siderite and ankerite, were selected for a series single flotation experiment. The aim was to discover the flotation difference of these minerals, furthermore, to explore a new flow sheet for the iron ore containing carbonates. The results of single mineral flotation experiment reveal that the combination regulators, starch and CaCl2, in different pH extent, can make these minerals taking on obvious flotation difference, which make it possible to process the iron ore containing carbonates. A new flow sheet, step-flotation, to process iron ore containing carbonates is explored, that is, first step, direct-flotation processing, is to eliminate the bad effect that the carbonates bring in flotation system by collecting carbonates under neutral condition; the second step, reverse?flotation processing, is to get qualified iron concentrate by collecting quartz under alkaline condition. Manual mixed ore sample were processed successfully through this new flowsheet under proper reagent system, which has absolute advantage compared with routine flowsheet. Actual ore sample of compound magnetic separation concentrate were processed successfully both open and closed circuit experiment through this new flowsheet. SEM and EDS were used to probe the reason why carbonates affect the regular processing. It is analyzed that moderate floatability of siderite and its coating on the surface of hematite and quartz make the phenomenon ?concentrate and tailing no separated?. This research provides a reasonable processing scheme for iron ores containing carbonates and can be used for reference in processing other complicated, refractory iron ore.

Jan 1, 2014

By S. Q. Zhu

Coal Water Mixtures (CWMs) are densed suspensions of coal particles in water. Viscosity is one of the most important rheological properties of CWMs and it is desired to be as low as possible. The slurry viscosity was influenced significantly by additive formation, the particle size distribution and the ash content of the coal. However, the influence of dispersants is most obvious. At present, there are several kinds of dispersants such as polymeric styrene sulfuric sodium, lignin sulfonate, humate, polycarboxy salt, ethylene epoxide surfactant. In this paper, a newly synthesized CWM dispersant has been reported, which is an efficient anionic surfactants of polycarboxylic acid type. The synthesis process includes three steps. At the beginning, the polyglycol acetate ester has been performed by acetic acid and polyethylene glycol (PEO) on the condition of acetic-acid/PEO ratio 1:1.1, at 368~373K for 30 minutes. Then the macro-monomer is prepared through the esterification of 85.71% acrylic and 14.29% polyglycol acetate ester, at 368~373K for 10 minutes. After that, the polycarboxylic acid CWM dispersant is polymerized using proper proportion macro-monomer, acrylic (AA) and sulfonic styrol sodium, at 368~373K for 1 hour. This new dispersants are used in the coal water mixtures formulation. Four kinds of coal used in the experiment are Shuang Yashan, Tunliu, Luning, Changcun samples. ? The highest concentration for shuanyashan coal is 70% when the dosage of dispersant is 0.4%, and the content of -200 meshes particles is 75.53%. As the dosage of dispersant de-creases to 0.25%, the Shangyashan CWM concentration is 67%. ? For Tunliu coal CWM concentrations are in the range of 76% to 75% when dosage of the dispersant changes from 0.4% to 0.25% at the same particle size distribution of 83.5% minus 200 meshes. ? The highest concentration for Luning coal is 69% when dosage of the dispersant is 0.4%, and the content of -200 meshes particles is 88.86%. ? For Changcun sample, the coal concentration of CWM is 73%~75% when dosage range of the dispersant is 0.35%~0.5%. The experiments show that the synthesied dispersant is quite promising for some coals CWM preparation, but a little bit coal-dependent. The Proximate and Ultimate analysis, surface characteristic measurement have been made to investigate the interactions between coal and additives.

Jan 1, 2014