Search Documents

By I. I. Beloglazov, G. A. Iusupov, A. Ju. Feoktistov

"The aim of this paper is to study the numerical modeling of the crushing process in a jaw crusher with complex motion jaws using Discrete Element Method (DEM). The main goals are to ensure the conformity of numerical simulation results to the experimental data, optimize the operating modes and the crusher design and develop automated verification and calibration methodology. It is offered to use automated selection of mathematical model parameters using large- or laboratory-scale experiments instead of deriving parameters from conventional intensive material tests (e.g. drop-weight test). Experimental data were obtained from a large-scale crusher designed and manufactured by the company “Mekhanobr-Tekhnika”. Both jaws have their drive shafts located asymmetrically; one jaw is driven in the upper part, the second at the base. The crushing process involves fragmentation of single smoothed rectangular granite particles of the same weight. During the experiment, the required parameters such as particle size distribution were obtained for further computer simulations. Based on the obtained experimental data, the Rocky DEM model was built. Simulation breakage parameters were calibrated using automated parameter selection methodology based on multiple set of parameter-controlled simulations. A good correlation of the experimental data and numerical simulation data was obtained. The methodology in combination with well-known capabilities of simulation modeling will help reduce the research time in the development of new mineral processing equipment.INTRODUCTION Preparation of rock mass for enrichment includes the power-consuming processes of crushing and grinding. Initial rock mass crushing is performed by means of drilling and blasting operations. To reduce the average size of a rock piece, primary crushers, mostly jaw crushers, are further applied. The advantages of the jaw crusher are simple design, easy maintenance and repair. One of the drawbacks is large oscillating masses and, thus, high power consumption during operation (55 - 200 kW). Jaw crushing simulation will help optimize the crushing process and improve further rock transportation and processing performance."

Jan 1, 2018

"This research represents a shift away from empirical models that lock the industry into 50-year old inefficiencies with little response to operating variability. The mechanistic and intrinsically dynamic mill model under development steps up to a new paradigm using the latest computing capabilities and physical understanding of breakage and transport to transform predictive capabilities for design, optimisation and on-line control with variable feed. The milling process is broken down into discrete sub-processes, each of which can be modelled as an object in the whole model and in the model code. These objects can be upgraded or exchanged without having to rewrite or restructure the remainder of the code. Sub-processes include: feed into mill; transport along mill; presentation to impacting events; range of impacting forces; probability of being impacted in different zones in the mill as a function of particle size and density; suspension in slurry; and discharge out of the mill. The unit and processes surrounding the mill (feed and recycle conveyors, slurry pump and pipe, cyclone and recycle crusher) have also been modelled, in order to incorporate the effect of recirculating load coming from a cyclone or a recycle pebble crusher, respectively for ball mills or SAG mills. Each unit is modelled dynamically and PID controllers have been added to control pumping flowrate from sump and water addition for cyclone feed dilution. The paper demonstrates the predictive capability of a dynamic, mechanistic model and is used to test the sensitivity to the sub-processes, comparing different formulations and highlighting the aspects that require further development. Validation on pilot tests and application to industrial data is presented. This approach is currently undergoing industrial trial on sites, for use in on-line model-informed process control. Considerable further development is required to incorporate the full mechanistic structure planned for this model."

Jan 1, 2018

By A. Akcil, O. Celep, C. Erust, E. Y. Yazici1, H. Deveci1

"Recycling of WEEE has already gain prime importance from both environmental and economic point of view. For the recovery of metals from e-waste, many conventional physical, bio/hydrometallurgical and pyrometallurgical processes are proposed. Economic potential of e-waste is mainly driven by its precious metal content. Physical separation methods (e.g. electrostatic, magnetic, eddy current and gravity separation) exploit the differences in the physical properties of metals and non-metals. Physical separation methods are simple and economically sound but they suffer from metal losses and ineffectiveness at fine sizes. Hydrometallurgical processes are promising owing to their relatively low cost, reduced environmental impact, potential for high metal recoveries and suitability for small scale applications. Hydrometallurgical processes can be developed for selective extraction of base/precious metals using suitable reagent systems. Sulphate-based leaching with a suitable oxidant (e.g. H2O2, O2, Fe3+) is effective for copper and other base metals. After removal/recovery of base metals, precious metals can be easily extracted using various lixiviants including thiosulphate, thiourea, cyanide and chloride. However, further research is required to develop new, cost effective and environmentally friendly processes and/or refine existing ones for leaching and, in particular, downstream processes. INTRODUCTION Electrical and electronic equipments are indispensable to modern societies with numerous applications in the field of medicine, transport, communication, education, security and environmental protection. With technological developments and innovations, the replacement of old equipment leads to ever fast accumulation of waste materials such as waste electrical and electronic equipment (WEEE or e-waste). People are upgrading their mobile phones, computers, televisions, audio equipment and printers more frequently than ever before (Babu et al., 2007; Lee et al., 2007). With the rapid growth in technology today, the life span and utilisation period of most electronic and electrical equipment has been reduced considerably with concomitant generation of huge amounts of WEEE over the past several decades. According to statistics presented by Balde et al. (2015), total WEEE produced around the world was 41.8 million tonnes in 2014 and expected to rise to approximately 50 million tonnes by 2018. Kumar et al. (2017) estimated that annual growth rate for the WEEE stream is 3–5% (Singh et al., 2016). The aim of this paper is to provide an overview of physical separation and hydrometallurgical methods available for the treatment of WEEE."

Jan 1, 2018

By H. Wotruba, L. Gronen, A. Hellmann, S. Sindern, J. Katzmarzyk

"This paper focuses on the beneficiation of the REE-Y-Nb-Zr complex ore from the ‘Khalzan Buregtei’ deposit, Mongolia. Pre-concentration based on mineralogical studies was investigated at the Unit of Mineral Processing (AMR) and the Institute of Applied Mineralogy and Economic Geology of RWTH Aachen University. In order to minimize the energy consumption in the most energy intensive grinding process a pre-concentration process using dry magnetic separation of particle sizes coarser than required for the liberation of the valuable ore minerals was designed. Dry magnetic separation in the particle size range of 63-250 µm is suitable as the pre-concentration method, due to the intergrowth of REE-Y-Nb-Zr bearing minerals with magnetic minerals determined by QEMSCAN© analysis. The results showed that a mass reduction of 45.3 wt.-% at high recoveries of REE, Y, Nb and Zr (90 wt.-% and higher) in the pre-concentration product was achieved at the beginning of the process chain. The improvement of process efficiency as shown in this study depends on the abundance and association of minerals affecting the magnetic properties (e.g. hematite) of the ores. Therefore, these mineralogical parameters are as important as grain size and ore grade for the geometallurgical evaluation of potential mining operations at ‘Khalzan Buregtei’.INTRODUCTION Polymetallic deposits containing other critical elements besides REE have the advantage of being robust to economic development and fluctuations of individual metal prices. (Gronen et al., 2016). These deposits can host economic grades of heavy and light REE, Y, Nb, Ta, Zr in complex mineralogical compositions. About 120 deposits of this type are known worldwide, including ‘Norra Kärr’ in Sweden, ‘Strange Lake’ in Canada and ‘Khalzan Buregtei’ in Mongolia which are not valued economically yet. (Salvi. & Williams-Jones, 2004.)"

Jan 1, 2018

By S. A. Kondratyev

"The present research work aims at disclosing the dependence of flotation concentrate recovery and its grade on the physically adsorbed collecting reagent properties, viz., surface pressure in the reagent film at gas-liquid interface, velocity of reagent species spreading over the said interface, relation between interaction energies of collector molecules within a film and with water dipoles.When using a single collecting reagent it is possible to improve the flotation concentrate grade in two ways, namely, by reducing collector consumption rate or using a weaker reagent. According to the proposed mechanism, a decrease in the physically sorbed species of the collector leads to a decrease in the rate of removal of the kinetic restriction of a flotation contact formation. As a result, the recovery of the useful component is reduced and the content of valuable components in the flotation concentrate is increased. The relationship between the spreading velocity of physically sorbed species at the gas-liquid interface and the recovery and quality of the flotation concentrate has been experimentally proved. Reduction in collector consumption lowered the valuable component recovery at a higher grade of the concentrate.The reasons were established for a rise of valuable content in the flotation concentrate if a weaker collector was used. It is justified that the use of a weaker collecting reagent with a shorter hydrocarbon fragment declines physically sorbed species of collector. The spreading velocity of collector derivatives at gas-liquid interface tends to lower along with less participation physically sorbed species of collector in formation of a flotation aggregate. The spreading velocity is determined for products of interaction between butyl-and ethyl-xanthates and lead nitrate at gas-liquid interface. It is found that the spreading velocity of butyl-xanthate derivatives is higher than that of ethylxanthate derivatives.The research work gets insight into the nature of relation between useful component content in the flotation concentrate and the useful component recovery. It is pointed out that adjusting the collecting activity of a collector makes it possible to influence a useful component content in the froth product thus gaining a compromise between wanted grade and recovery parameters."

Jan 1, 2018

By A. P. Purgin, M. G. Viduetsky, I. F. Garifulin

"The combined treatment process for mine, tailings storage facility, quarry, circulating, and waste water in the mining and metals industry brings together the conventional chemical treatment processes and pneumatic flotation cells of the KFM series. The key principle of the process is preparing the water for treatment by saturating with finely dispersed air bubbles in the flotation cell blowers. Gas-air lift dispersers located in the lower part of the cell body additionally saturate the cell’s contents with finely dispersed air. Due to the residual content of flotation agents in the treated water, hydroxide ion-air aggregates form at the aerator outlet, supporting the efficient precipitation of hydroxide ions of heavy non-ferrous metals, calcium and magnesium ions. This process was tested in the pilot plant KFM-180 with a raw (untreated) water capacity of up to 18 m3/h per 1 m3 of the flotation cell volume using a mixture of the tailings storage facility and mine water from JSC Safyanovo Copper. The treatment process included raw water treatment with lime, aeration in KFM cells, and filtration in a sorbent bed. The content of metal ions in the treated water is lower than in the feed water by a factor of up to 170,000 and approaches the standards: aluminum 0.016-0.02 mg/l, copper 0.0043-0.0045 mg/l, zinc 0.049-0.052 mg/l. circulating water of Soryin Tailings Storage Facility at JSC Svyatogor. The treatment process included raw water treatment with lime and alkali, aeration in KFM cells, and filtration in a sorbent bed. The content of metals in the treated water is lower than in the feed water by a factor of up to 9000: copper 0.022 mg/l, zinc 0.012 mg/l, iron 0.012 mg/l, manganese 0.015 mg/l, nickel 0.132 mg/l, arsenic 0.016 mg/l. Water hardness is significantly lower: calcium - 12.6 mg/l, magnesium - 1.1 mg/l. This process can be used in the treatment of mine, quarry, tailings storage facility, and circulating water at mining and non-ferrous metals projects."

Jan 1, 2018

By O. L. Kachor, A. V. Bogdanov

"In 2015 in the frames of federal special-purpose program «National system of chemical and biosafety of Russian Federation (2009-2014)» Federal State Budget Educational Institution of Higher Education ""Irkutsk National Research Technical University” (further–INRTU) performed works aimed at disposal of accumulated arsenical residues at industrial site of the former Angarsk arsenical plant (AAP) processing arsenious ores from Svirsk town in Irkutsk region. The plant in 1934-1949 produced arsenic trioxide for the defence industry. Prior to starting the works on disposal of industrial pollution focus the total amount of cinders stored on 13 ha of industrial site of AAP was 156 900 tons with 1% average arsenic content. Close to the cinders there were also remains of industrial buildings and process equipment in the amount of 6 600 m3 that contained 150 tons of arsenic. Additional source of pollution at the industrial site of AAP is contaminated soil amounted to 48 000 tons. Proven reserves of gold and silver in the cinders were 6.1 and 47 g/t respectively. In 2015 the source of arsenious pollution was detoxificated according to mineral matrix technology and stored in a special landfill with separate stocking of gold-containing cinder and other arsenious residues. This technology of waste disposal specifies extraction of valuable metals from cinder in future. The similar case is with Vershino-Darasunsky settlement in Trans-Baikal Territory where the abandoned industrial site of the former arsenic plant is located in the central part of the settlement. The concentration of arsenic and valuable components can be compared to the concentration at AAP. Since 2016 the demand for removal of such industrial pollution sources is legislated due to amendments in Federal Law No. 7-FZ on environmental protection. It results in a real possibility to remove such dangerous industrial residues deposits as the one located in Vershino-Darasunsky settlement. INTRODUCTION In the frames of federal special-purpose program «National system of chemical and biosafety of Russian Federation (2009-2014)» as well as the Irkutsk region program “Environment protection in Irkutsk region"" for 2006-2015, INRTU performed the works aiming at disposal of accumulated environmental deprivation–arsenical residues from the former Angarsk arsenic plant (further - AAP) (Figure 1) on processing of arsenopyrite ores of Svirsk town in Irkutsk regionThe plant produced arsenic trioxidein 1934-1949."

Jan 1, 2018

By E. V. Mezentseva, S. M. Okunev

"In the article there is set forth a development experience of JSC LEBEDINSKY GOK Beneficiation Plant concerning the plan of increase in the production volumes of the iron ore concentrate with Fe content more than 69.5%. There are considered the issues regarding implementation of the updated process scheme of the concentrate beneficiation using fine screening operation, its industrial tests have shown an exploitability of this development direction. There are described the issues relating to the ceramic filters for dehydration of the additionally-beneficiated concentrate, there are given the production and process figures achieved during the exploitation. The methods of the research. In the paper there have been used the following scientific research methods: the methods of system analysis, mathematical statistics, classification, comparison, modelling, observance, experiment. INTRODUCTION JSC LEBEDINSKY GOK is the largest leading enterprise for iron ore beneficiation and the unique RF producer of the merchant hot briquetted sponge iron (HBI) highly demanded by the consumers. Raw materials for hot briquetted iron production are fluxed pellets produced from iron ore concentrate with Fe content more than 69.5% (additionally-beneficiated concentrate). Strategic program of the plant’s development foresees expansion of production of the highly demanded products that imposes a necessity of expending capacity of the enterprise and implementation in production of modern processes and equipment having low resource intensity and ensuring in addition a high efficiency. Construction of the third stage of the HBI Plant became one of directions for the strategic development of JSC LEBEDINSKY GOK implemented in 2017 that caused a demand in the production volumes and filtration of the iron ore concentrate with Fe content more than 69.5%. Purpose of the work – to develop and to provide a rationalization for efficiency of the production process and filtration of the iron ore concentrate with Fe content more than 69.5% ensuring increase of production volumes and its prime cost."

Jan 1, 2018

By Jia Ma, Lu-De Qiang, Zhi-Chao Liu, Chun-Feng Li, Guang Li, Bao-Bin Tang

"At present, research on the surface chemical properties of uranium minerals is very scanty, which restricts the research progress of uranium ore flotation process research. The research aimed at exploring the surface characteristics of two common uranium minerals and providing basis for flotation process to enrich uranium minerals in ore. This paper selected pitchblende and uraninite as the object of study, which are widely distributed in uranium deposits. We chose out the pure minerals of pitchblende and uraninite from different ores collected from different uranium deposits. By means of Zeta potential test and X-ray photoelectron spectroscopy (XPS) test, a preliminary study on surface characteristics of the pure minerals of pitchblende and uraninite was conducted. And the significance of the change of Zeta potential, the elements composition and valence state on the minerals surface for flotation was discussed. The research shows that, the Zeta potentials of pitchblende and uraninite in pure water are negative mainly when the pH value varies from 2 to 11, which maybe a result of the difference of ionization capacity between two kinds of oxy-compounds on the surface of minerals. On the surface of pitchblende and uraninite, the metal elements are mainly U, Th and Pb. U is mainly in the form of UO2, Th is mainly in the form of ThO2, and Pb is mainly in the form of Pb and PbO. Based on the surface characteristics of pitchblende and uraninite, we can select process and reagents appropriately in uranium ore flotation.INTRODUCTION Globally, the major challenges associated with exploitation of low grade ores are about finding economically feasible processes for reducing the mass of gangue minerals (Filippov et al., 2012). Among the beneficiation technologies of low grade uranium ores with complex minerals assemblage, flotation is the common process which is used to reduce production cost and eliminate the acid-consuming minerals (Li et al., 2016; Liu et al., 2015)."

Jan 1, 2018

By I. Yelkin, Erico Tabosa, Alex Jankovic, R. Hayashida, R. Faveere

"The mining industry faces growing challenges from more complex and lower grade deposits, rising costs, limited energy and water availability, and increasing societal pressure to operate more sustainably. Mining operations need to be more efficient, not just to reduce environmental impact, but also to remain economically viable.To maximize profitability and sustainability, existing operations and new projects must consider integration and optimization of all stages of production. A mining operation is essentially a series of inter-connected processes, with the performance and outputs of each stage affecting the subsequent ones. Optimizing stages in isolation can result in sub-optimal overall performance.The industry has long recognized the benefits of holistic optimization using the Mine-to-Mill concept, and there are many well documented successes. However, it is increasingly common to observe operations simply increasing explosive consumption in the mine and expecting optimization of the entire value chain (mining and processing). For true holistic optimization, blast intensity is not necessarily increased, but rather adjusted to best suit the requirements of the different types of ores treated, the circuit configuration and equipment, installed comminution power and the downstream beneficiation processes. It is a fully integrated effort with optimization of many aspects in the mine, comminution and separation processes.To be successful, optimization of the production chain from mine to process requires a site-specific, structured methodology supported by extensive ore characterization, auditing, surveys, data analysis, mathematical modelling simulations and a cost / benefit analysis. Following this methodology, optimization strategies are rapidly identified and implemented considering mine and plant constraints. Management needs to set up appropriate KPIs and site personnel need to be trained for the new operating strategies to be successfully incorporated into site practices and procedures in the production environment. This will ensure the benefits are achieved and maintained. This paper describes the methodology employed by Hatch to improve overall efficiency and profitability from mine to process. Two case study examples at Russian gold operations and benefits achieved are presented."

Jan 1, 2018

By Sergey Romanenko, Tatyana Aleksandrova, Karen Arustamian

"Current status of question about grinding stage effect to electrochemistry parameters of operation preparation slurry before intermediate selective flotation was assessed in the present scientific work. Needs of more detail study chemical reactions in the slurry preparation and flotation processes were shown. The ores are polymetallic sulphide type and the one are most difficult for mineral processing. The methodology allows increase information base during floatation tests. Ionometric methods and elements of neural network have been used in the study of mineral processing questions.We have also identified the relationship between the received values of the electrochemical parameters and the technological results in selective flotation. The optimal values of the electrochemistry parameters in operation of the preparation slurry before selective flotation has been found. The main effect of using the proposed methodology is to obtain scientifically based solutions to improve the technology parameters of flotation polymetallic sulfide ores. Challenging issue of selectivity of sulphide-polymetallic ores will be considered using case study of sulphidepolymetallic ores. It was shown that several factors are formed in ore grinding: formation of hydroxyl oxides of iron compounds, copper cation leaching, metal-sulphide and metal-sulphite complexes formation. The chemistry was revealed for current processes in slurry preparation operation before selective flotation. Quantitative assessment of interrelations between electrochemical parameters of slurry and process performance was given with using electrochemical control methods. Neuron network-based model was estimated based on data array and was allowed to establish optimum electrochemical conditions of metal-sulphite complex formation to provide maximum efficiency of selective flotation.INTRODUCTIONPhysical and chemical processes that take place in ore grinding have a significant impact on flotation selectivity and can cause low selectivity of the flotation process. Today this issue is given much attention. In the paper [1] it is pointed out that sulphide oxidation products and slurry components, such as sulphide ions, metallic iron and its oxidation products, have effect on flotation performance. So, metallic iron has impact on metal-sulphite complex formation as a result of oxidation-reduction reactions as follows:"

Jan 1, 2018

By Q. Cui, Z. G. Song, S. S. Lin, S. Q. Li, S. S. Lu, G. B. Zheng, A. J. Ren

"Mine tailings is one of the most important bulk industrial solid wastes, but its rate of comprehensive utilization is relatively low. Efficient separation, recovery and utilization of the valuable components is one focus of the comprehensive utilization of tailings. Beneficiation recovery of the valuable minerals is the most direct comprehensive utilization method for tailings. There are generally different kinds of nonmetallic minerals contained in the nonferrous metal mine tailings, which are secondary mineral resources waiting for further developing and recovery. Comprehensive utilization test studies on fluorite in tungsten beneficiation tailings and feldspar in molybdenum beneficiation tailings have been carried out by author and good test results are achieved. Some of the technologies developed in the test study have been applied in industrial productions, which have been working well. The economic, social and environmental benefits are remarkable. Our test studies and some production practices will be summarized and current situation and existing problems of comprehensive utilization for nonferrous metal mine tailings will also be discussed. Assumption and prospect for the future study on comprehensive utilization of nonferrous metal mine tailings will be brought at last.INTRODUCTION Mine tailings is one of the most important bulk industrial solid wastes, but its rate of comprehensive utilization is relatively low. Efficient separation, recovery and utilization of the valuable components is one focus of the comprehensive utilization of tailings. Beneficiation recovery of the valuable minerals is the most direct comprehensive utilization method for tailings. There are generally different kinds of nonmetallic minerals contained in the nonferrous metal mine tailings, which are secondary mineral resources waiting for further developing and recovery. Comprehensive utilization of nonmetallic minerals of nonferrous metal mine tailings not only can improve the value of the ore but also reduce the stock of tailings, being the key to reduce emissions at source for exploitation of nonferrous mineral resources (Cai, Yang, 2000)."

Jan 1, 2018

By E. G. Ozhogina, O. B. Kotova

"The ores of black, non-ferrous, rare, noble metals are mostly distinguished by a variety of mineral types and complexity of their material composition.The article is devoted to the promotion of the concept of mineral processing in modern realitiesof the deficit of high-quality ores and increase their demand.Normative and methodical documentationsfor specific types of analysis with the definition of the field of application are shown. For example,the pyrochlore-monazite-goethite ores from one of the deposits from Eastern Siberia - Chuktukonskoe ore fieldare tested. The development of mineralogical methods, and testing of specific raw materials are shown.The method of small-angle X-ray (and also synchrotron) scattering, which was developed for solving problems associated with structural high-resolution diagnostics, was tested for bauxites of Vezhay-Vorykvinskoye field. KEYWORDS Technological mineralogy, rebellious ores, ore quality assessment, ?mineralogical-analytical methods INTRODUCTION A highly intense production of many types of mineral raw results in gradual depletion and deterioration of mining-geological and mining-technical conditions of development. Relatively easily accessible and rich deposits are getting exhausted in the first place, and it is necessary to involve poor and rebellious ores into production and processing. Traditional technologies can hardly be applied (Chanturia, 2017; Bazin et al., 2014; Ponaryadov, 2017). The urgency of development of the concept of technological mineralogy focuses on the confirmation of new methods and approaches to the development of mineral raw, creation of scientific and methodological prerequisites for solving the problem of rational development of mineral raw, maximal extraction and integrated application of all minerals (both principal and associated), expansion and strengthening of mineral and raw base. The article is aimed at updating tasks that should be addressed within the applied mineralogical researches: – the forecast of quality of ore at early stages of exploration and technological indicators for the redistribution of raw, – interactive monitoring of these indicators by mineralogical and analytical methods; – assessment of environmental consequences of mining and processing of minerals and measures that eliminate these consequences."

Jan 1, 2018

By L. A. Vaisberg

"Mining processing plants are the most high-performing industrial enterprises in the world economy system. Even at an average-scale mining enterprise, the grain-size separation equipment continuously processes 105 to 106 dissimilar mineral particles per hour. In separation by physical properties, their number increases by at least 10 to 50 times. Mathematical modeling of such a high flow of discrete particles is carried out using two different approaches: the discrete-particle and the phenomenological methods. The calculations demonstrate the possibility of handling big data when describing the processes of separation of granular material. INTRODUCTION The interest to the screening process and the process of formation of new screen designs in Mekhanobr is traditional since the moment of its foundation. It is symbolical that the first publication of the Mekhanobr proceedings in 1924 was the monograph dedicated to screens and screening products as such, which was the first one in the world at that moment. It was a book of Prof. L. B. Levenson, one of the founders of Mekhanobr, who headed the Technical Bureau of the Institute. Vibratory screening is the most mass process in the technologies of solid minerals processing, which determines significantly the energy demands of crushing and grinding cycles, and at some enterprises determines the quality of the final product, for example in case of crushed stone, coal or abrasive materials production. The general understanding and simulation of the process of poly-dispersed granular materials vibratory screening was developed at several conceptual levels taking into account the features of classification of materials with different size and density.Considering the real industrial processes of vibration screening, it shall be noted that at the sieve surface of the screen in the initial part of the deck the classification in a thick material layer (in natural conditions) occurs, which further transfers to a thin layer (free movement). In the process of screening of light minerals, for example coal or metallurgic feedstock, screening is mainly performed in the thick layer."

Jan 1, 2018

By Klaus M. Hahn, Hermann Wotruba, Bernd G. Friedrich

"Due to an increasing demand for nickel and cobalt and the depletion of nickel sulphide deposits worldwide, the production of ferronickel from lateritic nickel ores becomes more significant. About 60 percent of nickel reserves are present in laterite deposits. Common production methods like acid leaching or smelting operations implicate high material and energy consumption. Physical processing methods are also not efficient, because of the fine microstructural intergrowth of the minerals carrying valuable elements such as nickel and cobalt. Due to the high energy consumption of metallurgical treatment of lateritic nickel ore (nickel grade: 0.8 - 3.0%, Co: 0.05 - 0.15%), the separation of waste material (about 75 - 85%) before the metallurgical treatment is desirable. Therefore, an alternative process has been developed, combining a pyro-metallurgical pre-treatment with selected mechanical processing methods. The developed process consisted of a selective pre-reduction and non-selective segregation of the contained metal phases in the first stage. By this, the properties of the metal carrying minerals were changed and could become subject to concentration by means of fine beneficiation processes afterwards. The parameters of the pre-reduction and segregation were varied and the pre-treated samples were examined concerning their efficiency of metalization grade and metal grain size. This paper describes the investigation of pre-treatment methods of a lateritic nickel ore. The pre-treatment and possible subsequent separation methods were examined with regard to the recovery of the valuable elements. Metalization grade was around 80% for both Ni and Co with metal phase grain sizes below 20 µm. Scanning electron microscopy revealed distribution of new metal phases not only on the reducing agent, but also on the “slag” material.INTRODUCTION Nickel laterites are characterized as strongly weathered regoliths with several zones containing reserves of nickel (Ni) and cobalt (Co). These laterites are formed on serpentinites and ultramafic rocks under climatic and/or tectonic conditions that have changed over time (Butt & Cluzel, 2013). The formation of Ni laterites is influenced by numerous geological and environmental factors. In general, there are three ore types named according to the dominant Ni hosting minerals: oxides, hydrous magnesia (Mg) silicates and clay silicates (Butt & Cluzel, 2013). The most Ni laterite deposits contain two of these ore types, usually an oxide zone and an either clay or Mg silicate zone. Distribution of these principal deposit types, their average Ni-bearing phases and mean Ni grade are shown in Table 1. A schematic profile of the different deposits based on the development on serpentized ultramafic rocks is given in Figure 1 (Butt & Cluzel, 2013)."

Jan 1, 2018

By Junwei Han, Kai Xue, Wenqing Qin, Tan Xu, Fen Jiao, Lianbing Cai, Wei Liu

"The research aimed at solving the problem of the stacked spent magnesia-chrome refractories using in non-ferrous metal smelters, which contain various heavy metals and are considered as a hazardous waste. The purpose of the research is to recycle the spent refractories environmentally and economically using gravity separation and flotation to obtain metal concentrates for smelting and using chloridizing volatilization to remove the trace metals from tailings, providing raw material to reprocess magnesia-chrome refractories. In the course of the study, laboratory techniques for the preparation of experimental samples of spent magnesia-chrome refractories were developed including the sequence of operations of material grinding, gravity separation, tails regrinding, flotation, filtration and subsequent unification of concentrates, filtration and chloridizing volatilization of tails, and collection of volatiles. Laboratory tests carried out on several types of samples of spent magnesia-chrome refractories from different smelters showed that gravity separation provided increase in quality of concentrates including about 80% metals (including Ag, Pb, Bi) and flotation separation provided increase in recovery of concentrates under the condition of 200g/t of emulsified kerosene, and 500g/t of combined collector. Based on combined technology of gravity and flotation separation, about 90% metals were recovered from the refractories by a closed-circuit test and the total concentrates contained 40% metals, which can be returned to smelting process as a feeding. Because a small amount of metal in raw materials will seriously affect the performance of refractories, chloridizing volatilization is necessary for removing the remaining 10% metals from tails mixed 8% coke and 13% magnesium chloride at a temperature of 1200°C. Thus, the tailings can be reused as a raw material for new refractories.INTRODUCTION Magnesia-chrome refractory has been used extensively in various industries such as secondary metallurgy, non-ferrous furnaces and cement making due to their high temperature stability, low thermal expansion and outstanding erosion-corrosion performance at high temperatures (Gotod et al., 2005; Vezza et al., 1997; Gregurek et al., 2015). Generally, the magnesia-chrome refractories are produced from a mixture of magnesia and massive variety of chrome ores. However, massive chrome ores are being depleted throughout the world. Even more serious is that the heavy metal chromium (Cr) can transfer into soil and water, which will have an influence on the survival and development of human beings (Zhao et al., 2006; Jiang et al., 2004; Qintie et al., 2013). As a result, regulations treating spent magnesia-chrome refractories as potentially hazardous waste are being enforced, making their disposal difficult and expensive."

Jan 1, 2018

By Diego Mesa, Willy Kracht

Frothers may be classified as weak or strong depending on their ability to produce stable froths, which is related to the amount of water that they transfer from the pulp to the froth. They can also have an effect on the non-selective mechanism of recovery by entrainment, implying that both selectivity and froth stability are, at least to some extent, frother dependent. Solids, on the other hand, also have an effect on froth behaviour. Clays, which are characterized by their small particle size, laminar shape, and high specific surface, tend to report to the froth phase and have an enormous impact on both froth stability and the overall performance of the flotation process. The purpose of this work is to shed light on the effect that different frothers have on the froth behaviour when clays are present. In order to do that, two sets of experiments were conducted using frothers from the families of alcohols and polyglycols. For each test, the equilibrium froth height was measured at different frother concentrations in an agitated machine with an acrylic square-base cell that was 11 cm wide and 25 cm high. The cell was designed in such a way that froth was able to grow without concentrate discharge. In the first set of tests, pure clays such as kaolinite and montmorillonite were used. In the second set, an actual copper sulphide ore with a high content of clays was used as solid phase. The results, expressed as curves of equilibrium froth height against frother dosage, showed a coupled effect of frother-clay on froth behaviour for both sets of experiments. In some cases, the froth grew up until the border of the cell with only a few parts per million of frother. In other cases, the equilibrium froth height varied smoothly with frother dosage. The results suggest that choosing the right frother can be of use for controlling the froth behaviour when dealing with clay-rich froths, using frother dosage as the control variable. The application of these findings at industrial scale are discussed and some recommendations are given.

Jan 1, 2018

By Vishal Shukla, Ashok Kumar, C. Raghu Kumar, D. P. Chakraborty

"Traditional iron ore beneficiation plants using washing, screening, and jigging processes require large volumes of process water. Generated slime during processing, its disposal and impact on water usage, is an important concern for any mining company. The challenge today, during extracting iron ore, is how to dispose of slime such that it is contained and stable, while maximizing water reuse and minimizing surface footprint. The slime disposal methods are sensitive to the environment. Two major technologies presently being practiced for disposing the slime across the world are pressure filtration and paste thickening. In this perspective an attempt has been made to do comparative study between paste thickening and pressure filtration for selection of suitable slime disposable technology for Noamundi processing plant, Tata Steel. From the studies, it is evident that by adopting pressure filtration technique it was possible to produce filtered slime, whereas filtration, rate reduces significantly with the presence of finer fraction. Further , the greatest advantage of paste thickening is volume reduction of slime. By considering the technology limitation and comparative lab test work result, it is opined that combination of filtration and paste thickening technology is favorable in terms of capital and operating cost and slime >45 µ should be filtered and < 45 µ slime should go for paste thickening. The study and the results are presented in details.INTRODUCTION The beneficiation processes always end up with an enriched portion of desired mineral - “Concentrate” and an enriched portion of undesired minerals - “Tailing”. The proportion and nature of tailings generated in every beneficiation process differ from ore to ore and reflects the characteristics of the feed processed. The traditional method of tailing disposal in many mineral processing industries has been to dispose them as thickener underflow at around 35% solids. Though, it had certain advantages of transportation with ease but contribute to a greater volume occupied in the tailing dam. This sustained practice and failure to utilize the space available in the tailing dam judiciously endangered the mining industry. The tailing management has become the toughest task to the mining industry and most of the mines are running out of space for disposing the fresh tailings as many of these are at the verge of getting filled."

Jan 1, 2018

By Indrajit Paul, Atanu Pal, Kapil Modi, Sanjay Chandra, Chandra Sekhar, Srinivas Dwarapudi

"High alumina content in the Indian iron ore fines (2.5% Al2O3) resulted in poor quality pellets at the recently commissioned 6 MTPA pelletizing plant and a study was under taken to establish suitable pellet chemistry through proper fluxing agents. Limestone fluxed pellets were prepared at varying basicity (0 to 0.8) and pyroxenite fluxed pellets at varying MgO contents (0 to 3%) to study their effect on the metallurgical properties. Fired pellets were tested for their strength, RDI, reducibility and swelling. Microstructural studies, optical and SEM-EDS, were carried out to quantify different phases and their chemistry. Acid pellets exhibited poor quality whereas limestone pellets at 0.8 basicity and pyroxenite pellets at 1.5% MgO exhibited optimum metallurgical quality. Formation of widely distributed silicate melt in limestone pellets and high melting point slag & magnesioferrite in pyroxenite pellets found to improve their quality. However during commercial production of MgO bearing pyroxenite pellets, their room temperature and low temperature properties found to be inferior, but exhibited better high temperature properties, viz. softening-melting behavior. Contrary to this, commercially produced limestone pellets, comprising CaO, exhibited better strength and RDI but showed poor high temperature properties. To yield the benefits of both CaO (for good strength and RDI) and MgO (for low swelling and high softening), a dual flux combination was established by using both limestone and pyroxenite/olivine together that resulted in optimum metallurgical properties. Coke rate at the blast furnaces found to be reduced by 1kg for every1% increase of dual flux pellets in the burden.INTRODUCTION Iron ore agglomerate quality plays a vital role in decreasing the reducing agent consumption and increasing the productivity of blast furnace. In most of the integrated steel works, the burden mix for blast furnace is decided as per the availability of the iron ore agglomerates like sinter and pellets. More attention has been given in recent years to the use of fluxed pellets in blast furnace due to their good strength and improved reducibility, swelling and softening melting characteristics. Generally, quality of pellets is influenced by the nature of ore or concentrate, associated gangue, type and amount of fluxes added and their subsequent treatment to produce pellets. These factors in turn result in the variation of physicochemical properties of the coexisting phases and their distribution during pellet induration. Hence properties of the pellets are largely governed by the form and degree of bonding achieved between ore particles and the stability of these bonding phases during reduction of iron oxides (Panigraphy et al., 1990). It is important to note that conditions and parameters of pelletizing are specific to given ore or concentrate; the present study is undertaken for typical Indian hematite ore fines high in alumina. Except authors earlier work on quality of pellets from Indian iron ore (Dwarapudi et al., 2008, 2010), there is no considerable literature reported on the effect of pellet basicity and MgO content in the basicity range of 0 to 0.8 for Indian hematite ore."

Jan 1, 2018

By C. Dorfling, P. Albertyn

"Hydrometallurgical recovery of metals from printed circuit board waste typically involves multiple leaching stages; conventionally, base metals dissolution by mineral acids is followed by leaching of gold using cyanide or halide based lixiviants. Alternative lixiviants for gold leaching can reduce the potential hazardous nature of operation. The aim of this study was to investigate the feasibility of using thiosulfate as lixiviant for gold leaching from waste printed circuit boards. Batch leaching tests were performed to investigate the effects of thiosulfate concentration (0.1 – 0.2 M), ammonium concentration (0.2 – 0.4 M), pH (9 – 10.5), solids content (25 – 50 g/L), and copper content of the feed material on the gold leaching behavior. The concentrations of metals in liquid samples were determined by means of inductively coupled plasma atomic emission spectroscopy, and high pressure liquid chromatography was used to evaluate thiosulfate degradation/consumption. The ratio of thiosulfate to ammonia was found to have the most significant effect on the extent of gold leaching, with the best gold extraction observed at a ratio of 0.5 mole thiosulfate per mole ammonia. The lower pH range of 9 – 9.5 generally produced better Au leaching, while low copper extraction during the first stage base metal leaching stages has proven to be detrimental to gold leaching from the residue. Thiosulfate degradation/consumption increased and gold extraction decreased with higher residual copper in the feed. An optimum gold extraction of 78.5 % from base metal leach residue was achieved with 0.2 M thiosulfate, 0.4 M ammonia, and 0.02 M cupric ions at 25°C in the pH range 9 – 9.5.INTRODUCTION Background and Aim The recycling of e-waste is becoming increasingly important as it provides certain economic benefits apart from the obvious environmental benefits. Printed circuit boards (PCBs) are found in most forms of e-waste and contain especially high concentrations of base and precious metals. Hydrometallurgical processes are often considered for the recovery of valuable metals from PCBs; these processes normally implement several leaching stages to selectively recover certain metals."

Jan 1, 2018