Search Documents

By A. B. Holland-Batt

Deposition velocities play an important role in many fields of engineering and an impressive range of measured data has accumulated in the literature. Numerous workers have addressed the problems that are associated with the prediction of deposition velocity because of its particular relevance to the design of pipelines and pumping stations. However, despite this extensive effort, the calculation of friction heads still requires reference to experimentally based graphs to determine Durand factors and there is still scope for improvement in the prediction of the deposition velocity at different solids concentrations. Equations to characterise the relationship between the Durand factor and the volume concentrations of solids in the slurry are presented. A correlation for the prediction of the deposition velocity is also developed and tested against some of the classical experimental data. The application of predicted values of deposition velocity in assessing the potential for the sanding-up of spiral separators is then described and a case study is presented.

Jan 12, 1992

By C. L. Schneider, C. O. Gomes, R. P. King, J. A. Finch, D. Lin

Discussion is presented by Prof. King and Dr. Schneider of the paper by Lin, Gomez and Finch published in Trans.IMM C, vol.104, 1995, p.C155-C161. They conclude that the correction procedures used for simulated observations of simulated capped spheres are not reliable when applied to mineralogical data and that their relative ranking should not be extrapolated to other situations. Properly regularised solutions obtained with the use of appropriate kernels can be safely used for routine mineral liberation work and can be calibrated accurately against real mineralogical samples in the laboratory

Jun 19, 1905

By R. R. Hart, R. A. Evans

This paper outlines the the methods currently being used in the West Wales Area for preventing the occurrence of any outbreak of spontaneous combustion. Stress is placed on the importance of correlating the position of a Rider Seam which is prone to spontaneous combustion. The recent introduction of the UNOR Recorder has contributed to the ability to monitor the CO content of the general body of the air during any incident. The use of modern sealants and improved methods of applying them have enabled the few instances of spontaneous combustion in South Wales to be treated promptly and efficiently. The authors describe the current spontaneous combustion problems at two collieries.

May 23, 1905

By P. Mousset-Jones, G. Danko

Variations of the temperature and steam/moisture content of the air with distance and time are modelled for a single airway. The input for the simulation is an air temperature that varies with time, together with the moisture/steam content that results, for example, from a fire with a given distribution of heat and of fume concentrations at the beginning of the airway. The transport of heat and moisture to the surface of the wallrock is assumed to be simultaneous. Such multiphase convection may result in evaporation from the moist wall close to the fire and recondensation downstream. The modelling of this non-linear effect is a unique feature of the new simulation. A new analytical solution is used to calculate the conduction of transient heat within the rock mantle, which, in the event of a fire, is typically a short-term process. This allows for an arbitrary variation of surface temperature with time - unlike that permitted by the age function solution, which is limited to stepped temperature changes. An iterative numerical scheme that has recently been developed to simulate mine climate is used to calculate the coupled transient heat conduction and multiphase surface heat transport in successive length increments along the airway. To demonstrate the simulation procedure a numerical example is presented in which a fire with a given distribution of heat and fume concentrations with time is located at the beginning of an airway

May 1, 1991

Discussion of the paper presented at the Manchester Geological and Mining Society's general meeting held in Manchester, April 11th 1916, with Mr. Leonard R. Fletcher, President, in the chair, included questions asked and points for discussion raised by Bramall V., Paton J.D., Fletcher L.R., Siddall F.N., Stoker A. and Stone T., in particular on how to eliminate dust

Dec 1, 1916

By N. Powell, R. J. Pine

An algorithm is proposed for updating the probability of slope failure on the basis of sequential testing using Bayesian probability theory. The approach is novel and computationally straightforward since, unlike other methods, updating of the probability of failure is carried out directly. This is because the probability is treated as a random variable whereas other methods have considered it as a purely deterministic value or as a function of shear strength parameters that are updated individually. The prior information required for the Bayesian analysis is obtained by a conventional probabilistic analysis. An exponential distribution is then used for the probability of failure, applying the principle of maximum entropy. This distribution is continually updated for individual slope cells, where repetitive excavation creates several such cells and a corresponding series of Bayesian estimates of the probability of failure is obtained. The approach is applicable to most simulations but there are limitations on its use. A more mathematically rigorous refinement using the beta distribution is currently under development

Apr 1, 1996

By B. D. Rayment, J. D. Wilson, G. R. Davis

Wheal Jane, situated between Truro and the Carnmenellis granite, is under development by Consolidated Gold Fields, Ltd., as a tin producer. The main or B lode comprises a complex cassiterite-sulphide ore located in shear zones along the footwall of the lowest of a series of porphyry dykes (elvans) which strike ENE and dip 35° north. Minor mineralisation follows other elvan contacts and sets of later steeply dipping fractures. The localisation and overall geometry of the deposit is explained in terms of the complex structural geology of the Lower Palaeozoic metasediments and the shape and manner of emplacement of the invading Hercynian granite of Cornwall. Variations in the thickness and grade of the orebody, and in the nature of the mineralisation, are shown to be structurally controlled by undulations of the footwall contact of the B elvan. Wallrock sericitisation is present and is applied in exploration for ore

Dec 1, 1971

By R. R. Tatiya

The following procedure was used to determine cut-off grades: define the orebody profile; plan the stope layout and quantify the work involved; formulate equipment-performance norms; calculate unit costs; input process recoveries and metal prices; and calculate the cut-off grade. Use of the method is illustrated using data from a copper mining complex in India. Results from the study led to the following conclusions for underground mines in general. Cut-off dependent costs vary significantly with the stoping method employed, orebody thickness, the degree of mechanisation and the working efficiencies of the workforce and equipment. This applies even within the same deposit. Sub-level stoping and its variants can be operated at a lower cut-off grade than cut-and-fill and its variants. Thinner orebodies affect cut-off grades adversely, but with thinner orebodies very little further reduction in cut-off grade can be achieved once a certain minimum width has been exceeded. For the same stoping method and in the same mine the cut-off grade varies with the degree of mechanisation. Labour-intensive methods require higher cut-off grades. An allowance for working efficiency should be made when calculating cut-off grades. Higher process recoveries allow a significant lowering of cut-off grades

Jul 1, 1996

By R. W. Ruddle

The advent of new methods of roasting, “flash roasting and fluidisation”, which are now under development, combined with the use of oxygen-enriched air, may markedly increase the SO2 content of roaster smokes. Skogmo suggests that the production of smokes containing as much as 50 per cent SO2 should be feasible. The use of flash smelting processes may well enable a similar increase in the SO2 content of smelter smokes to be made. In this event the recovery of sulphur would be greatly cheapened and the process might well be much more economic, even if allowance is made for the cost of generating the oxygen

Jan 1, 1953

By A. G. Waters, N. J. Bristow

A comparative study was made of an untreated and a heated haematite ore and a sinter produced from a feed consisting of 100% ore, to study the influence on reduction behaviour of sinter bonding phases such as SFCA (silico-ferrite of calcium and alumina). Under low-temperature reduction conditions the order of increasing reducibility followed that of increasing porosity and surface area but under similar conditions at 900 degrees C the sinter exhibited higher reducibility than the ores even though the total porosity and chemical reducibility of the individual phases were lower. This behaviour can be explained in terms of the higher total porosity of the natural ore at low temperatures and the higher level of fine pores in the sinter at high temperatures due to the presence of SFCA, which acts to support the fine (c.0.1 micrometre) pores created by the reduction process. This leads to the conclusion that the main role of SFCA in sinter during high-temperature reduction is to maintain a high level of fine porosity. Some implications of this work for granule design and sintering practice are discussed

Apr 1, 1991

By D. J. Esdale, D. F. Pridmore, F. W. Lindman, J. H. Coggon

Almost all the presently viable nickel reserves in the Yilgarn Block contain nickel in a sulphide phase. Both volcanic peridotite- associated (VPA) deposits and intrusive dunite-associated (IDA) deposits are characterized by massive, matrix and disseminated sulphides (typically, pyrrhotite, pentlandite, pyrite, chalcopyrite, magnetite and other spinels), though in the IDA deposits the volume of disseminated sulphides is far greater than that in the VPA deposits. Potentially all geophysical techniques have application in the direct detection of these deposits'gravity for the detection of the dense massive and matrix ore; magnetics for the detection of magnetite and pyrrhotite in the ores; electromagnetics for the detection of the massive and matrix ore; and induced polarization for the detection of disseminated and to some extent matrix and massive ore. In practice the application of geophysical techniques is limited to a varying extent by (1) the relatively small size of an economic accumulation of sulphides, particularly the VPA deposits, (2) the extreme depth of weathering and lack of outcrop on the Yilgarn Block and (3) the abundance of geological noise or anomalous responses caused by sources other than economic mineralization.

Jan 1, 1984

By NA NA

Stamler Corporation manufactures of mining machinery and material handling equipment specialising in Feeder-Breakers to the mining and quarrying industries.

Jan 9, 1996

By NA NA

Background information on Exchem Mining and Construction and its products.

Jan 7, 1997

By W. S. Fyfe, G. V. Albino, Ekawat Sitthithaworn

The mineralisation is associated with a composite diorite to quartz monzonite stock of Permian to Triassic age that intrudes Devonian carbonate strata. In the intrusive rocks it is associated with potassic alteration and in the carbonate wall rocks it is hosted by prograde garnet-rich and retrograde epidote-rich skarn. Both porphyry and skarn mineralisation include disseminated and fracture-controlled mineralisation, the latter probably accounting for the major part of the contained minerals. Copper, gold, silver and zinc are strongly positively correlated within the mineralised zones, although there are small differences in metal ratios between the different ore types; molybdenum appears to be negatively correlated with copper and gold. Ore minerals include chalcopyrite, magnetite and pyrite in porphyry-type mineralisation and bornite, chalcopyrite, pyrite, magnetite and lesser haematite in skarn.

Jan 12, 1993

By L. J. Cabri

Although no complete mineralogical balances have been published, the background knowledge and proven, highly sensitive analytical techniques to produce them already exist. For PGE-Cu-Ni sulphide ores a combination of ore microscopy, image analysis and electron microprobe analysis with proton microprobe analysis of sulphides for Pd, Rh and Ru and ion microprobe analysis for Pt, Ir and Rh (in some minerals) should provide the necessary data when combined with reliable assays. Other sulphide ores, such as the Cu-Ni-(PGE) ores of Sudbury, Ontario, require a similar approach except that the ion microprobe would be more suitable for the analysis of Pd, Pt and Rh because of its greater sensitivity. Oxide-silicate ores may be harder to deal with quantitatively, although the potential to confirm the presence of trace PGE within silicates and oxides may be greater than in PGE sulphide and Cu-Ni-(PGE) sulphide ores. However, solid solution of PGE in oxides and silicates still requires thorough documentation and evaluation in terms of their significance for the overall metallurgical balance

Apr 1, 1994

By I. A. Scott, T. J. Napier-Munn

Size-by-size partition curves for mineral separation in dense-medium cyclones pivot about a single characteristic point. This is defined for stable, non-segregating media by the medium density and the proportion of the medium reporting to the underflow. The pivot point departs from these values for unstable, conventional media. The phenomenon can be represented by an equation with two parameters defining pivot point coordinates and two the Ep value. On the basis of experiments in a 200 mm cyclone using ferrosilicon media, simple regression equations were developed for the separation parameters in terms of operating conditions (the coefficients were likely to be site-specific). The experiments successfully decoupled the effects of medium density and viscosity and showed that the value of Ep was independent of the former but strongly dependent on the latter. A classification model was used to predict the density of the underflow medium, a knowledge of which is required to determine the pivot parameters. The model correctly reflects the performance trends observed in dense-medium cyclone operation and has the potential to be generalised to a wide range of industrial practice.

Jan 8, 1992

By L. Wade, R. Wang, M. A. Horton

Laboratory methods to find the mechanical properties of rock are inherently biased towards stronger strata, which best survive the sample preparation process. Geophysical techniques are not subject to such bias and may be used to predict mechanical properties rapidly and cheaply. Samples (151) were obtained from a borehole that had been comprehensively geophysically logged. The mechanical properties of the samples were established in the laboratory and correlated with the geophysical responses of the strata from which they came. The results indicate that, for homogeneous strata at least, it is possible to predict the unconfined compressive strength reasonably well from sonic travel time measurements made in the field. Predictions of static Young's modulus may also be made from this data source, but with a lesser degree of confidence. A multivariate regression equation is presented which relates down-hole sonic travel time to unconfined compressive strength, depth and the frequency of fractures in the rock mass. This equation may offer potential for the prediction of the mechanical rock properties of fractured and layered strata.

Jan 4, 1993

By L. T. Matthews, C. E. Loo, R. P. Williams

The behaviour of iron ores and fluxes in the high temperature zone of a sintering bed is extremely complex. Following a review of current knowledge, an attempt is made to define relevant terminology to describe the processes that occur in this part of the bed. A deformation temperature is used to quantify the initial formation of melt, which is produced predominantly by reactions between fine particles in the sinter mix. The subsequent assimilation of larger particles is considered to depend on the reactivity of the melt and the assimilation resistance of these particles. Novel laboratory experimental techniques are used to quantify these parameters. Results demonstrate that the properties of the raw materials used have an extremely important influence on the initial processes of melt formation and assimilation and also on the nature of the sintering reactions and sinter-bonding phases.

Jan 4, 1992

During the construction of storage caverns, and during their lifetime if the use to which they are put so requires, it is necessary to provide adequate ventilation to ensure the safety and comfort of the underground workforce. An analysis of likely contaminants during construction has indicated that where a large facility is situated in a rock mass of even moderate temperature climatic conditions are likely to be the limiting factor during most of the mining operation and atmospheric pollution when blasting is undertaken. Possible options for improvement are increased air flow, cooling of intake air and reduction of the heat source by altering the number and type of haulage units employed in the cavern. Local solutions are an alternative approach where heat problems are confined to a few specific locations

Aug 1, 1994

By R. G. Kidel, S. C. Doming

The project has shown that it is feasible for a junior company to reopen a narrow vein-style gold mine and successfully take it into production. An intimate understanding of the mineralisation and a flexible approach to mining are crucial, as are stringent cost control and efforts to keep overheads low. The project has confirmed the geological complexity of the Main Lodes, which consist of highly sheared quartz-sulphide infill in strongly sericitised granodiorite. The existence of discrete high-grade zones within the Hangingwall Lodes has also been confirmed. Broad low-grade zones continue to be recognised and require the local application of bulk longhole mining methods. The initial mine plan called for predominantly longhole stoping, but adverse ground conditions have meant that a switch to air-leg mining has produced higher run-of-mine grades. The excess capacity at the processing plant can best be used by batch processing, with its reduced maintenance requirements

Jun 21, 1905