Search Documents

By Robert A. Cortese, Lon D. Santis

This paper describes a method of measuring continuous detonation rates using standard electronic parts, coaxial cable, and a data recorder such as an oscilloscope. Three six-volt lantern batteries or a DC supply power the electronics that cost less than $100. Included are means of showing low battery power, finding the proper voltage scale on the recorder, and test triggering of the recorder. Modifications of the circuit allow for use in the field to measure charges up to 57 meters and for use in the laboratory to measure short charges. The high resistance (8.709 Ohms/meter) coaxial cable is a mass produced, special order cable available commercially. The driver circuit delivers a constant current to the cable, and as the detonation shorts the cable, a change in circuit voltage occurs. Recording this voltage change over time allows determination of detonation rate resolute to the sampling speed of the recorder. An oscilloscope or personal computer with a data acquisition card can easily record the data for analysis. Detonation rates recorded in the laboratory using the coaxial cable and the Bureau of Mines's traditional probes are presented. The system accurately measured the detonation rates of ANFO confined in steel pipe, detonating cord, and unconfined high explosive.

Jan 1, 1996

By M. Hagfors

On the underwater testing of explosives, the measuring system consists of water filled test pond, tourmaline based pressure sensor, measuring cable and measuring unit, which supplies the DC current to the pressure sensor. Depending on the length of the measuring cable, it is always possible that some signal damping may occur in case the measurements are carried out without the signal amplifier to keep the measuring system as simple as possible. Therefore the length of the measuring cable should always be as short as possible.

Jan 1, 2006

By C. Anderson, Mike Michaelis

Ammonium Nitrate (AN) - based commercial explosives are non-ideal explosives. This is because the chemical and physical structure is heterogeneous on a distance scale comparable to, and in many cases larger than, the reaction zone in the detonating explosive. Such systems consist of inter-molecular fuel-oxidizer systems. Attempts have been made to minimize the heterogeneous nature (inter-molecular distances) of these explosives; emulsion systems are the latest examples of these commercialized AN-based explosives which balance cost, utility and performance. This latter factor (increased performance) is a direct result of increasing the contact between oxidizer and fuel.

Jan 1, 2003

By Nan H. Lee, Christopher J. Hunter, Stephen H. Chung

Several factors affect the productivity of mining operations. The geological structure of a mineral deposit and the fragment size of blasted material are considered to be most influential. It is well known that productivity varies with mucking cycles and that this is related to the explosive energy produced by a blast.

Jan 1, 1991

By John Brennan

The Avalauncher has been an integral tool for avalanche mitigation work for close to 50 years. With their ability to place a kilogram of high explosives up to two thousand meters away, they routinely serve as a short range alternative to military artillery. The Avalauncher’s roots can be traced to a pneumatic baseball pitching machine used by Major League Baseball teams in the United States in the late 1950s. Throughout the decades, many modifications have been made to both the launcher and its projectiles. Current technology has allowed the Avalauncher to attain greater accuracies and operational range. In this paper I plan to cover not only the history of the Avalauncher but also explore its potential future.

Jan 1, 2009

By Roger Favreau, Patrice Favreau

The article reviews the aspects which contribute to the quality of the results from a blast with explosives, namely a good floor, no large blocks, easy mucking, and explains the mechanisms of the blasting process which decide on the quality of these aspects for a given blast method, and how these mechanisms can be simulated from basic principles. It proposes that good fragmentation size distribution can also be important if the rock is going to a crusher, e. g. for the ore in a mine and for the rock excavated in a quarry.

Jan 1, 2012

By Clara Godoy, Álvaro Dapía, Paulo Couceiro, Pablo Segarra, José Ángel Sanchidrián, Juan Navarro

This paper applies geostatistical tools in Measure While Drilling (MWD) data to estimate the probability distribution of values in all the points of the studied domain in order to assess the continuity of rock classes between boreholes. The analyses carried out by Ghosh et al. (2018) and Navarro et al. (2019) have been used as starting point of this work to classify the geotechnical rock condition in four classes: solid rock, fractured rock, cave- in rock and cavity. From it, an application for the geotechnical rock condition of orebodies have been developed, aiming at characterizing the rock before the charging the holes to minimize unexpected rock conditions and to address issues associated with charging and blasting operations. Such problems are closely related with non-optimal rock fragmentation after blasting.

Feb 1, 2020

By A. Ribeiro

The effective utilization of resources and process optimization play a crucial role in the sustaining and growth of overall businesses. This principle holds true in the mining sector, where particular attention is required during the comminution steps. This necessity arises from the fact that mining operations often consume substantial amounts of energy in mineral processing. Therefore, it becomes imperative to thoroughly study the integration of comminution steps. In many instances, an approach to be studied is the operation commencing with the drill and blast phase and culminating in the grinding product process. Nevertheless, establishing an optimal integration between drill and blast operations and the grinding phase is a complex undertaking due to the direct influence of rock characteristics on this process. And in many cases, the complexity and variability of such physical characteristics makes mining operations to ignore such influence. Consequently, Enaex Mining Technical Solutions (EMTS), in collaboration with Lundin Mining's Chapada Mine engineering team, and with the assistance of Hatch Consulting and Technology, has undertaken a comprehensive study aimed at enhancing mill throughput at the Chapada operation. The basis of this study lies in characterizing the rock masses present in the Chapada Mine to gain a deep understanding of the material that needs to be comminuted. Subsequently, the mineral processing team determined the most suitable size distribution for the Run-of-Mine (ROM) material. With this information, the drilling and blasting team built a site-specific blast fragmentation model, able to simulate various blast design scenarios. This approach enabled to optimize the utilization of available drilling and blasting resources while striving to achieve the optimum ROM characteristics. Since 2021, the Mine to Mill methodology has been progressively implemented at the Chapada Mine. As a result, the blasting engineering team now utilizes the blast plans generated by the fragmentation model simulations as a foundation for designing blast plans that align with the operational and financial capacities of the mine. Overall, it was predicted that this implementation could lead to an average increase in mill throughput of 13-22 % depending on blend feed, once all recommendations are implemented. Even with partial implementation, plant results demonstrate a 5 % increase compared to the period before the Mineto-Mill project, without any coarsening of the associated grinding product size.

Jan 1, 2024

By Larry R. Fletcher, John W. Kopp

The safety record for explosives in U. S. mining is excellent considering that over 4 billion pounds of explosives are now being used each year. However, blasting accidents remain one of the most serious concerns based on the number of injuries, the injury severity rate and the disaster potential. The Bureau of Mines has been analyzing blasting accident data obtained from the Mine Health and Safety Administration (MSHA) to determine the most frequent causes of mine blasting accidents and to examine trends in blasting accidents. This accident analysis is an update of two previous blasting accident studies conducted by the Bureau and published in 1983 and 1987.

Jan 1, 1991

By Lauren Shields

This paper discusses the application of current fragmentation models for underground blasting, establishes a conceptual fragmentation model for underground operations, and discusses the applicability of the mine-to-mill approach for underground blasting. Additionally, this paper also discusses selected case studies where the mine-to-mill approach is applied to underground mining operations.

Feb 1, 2020

By Satish Kate

Indian limestone mines which are highly mechanized in operation and supply limestone to the cement plants have been quite successful in devising ways and means to optimize blasting parameters, so as to have best fragmentation, powder factor, and cost of excavation. In primary blasting mechanized or manually mixed ammonium nitrate Fuel Oil is quite popular in dry holes, and in case of watery holes conventional packaged slurry/emulsions are being used. In order to avail the low density characteristics of the ANFO, some limestone mines have also used Saw Dust and Rice Husk along with ANFO. A number of field trials have been undertaken to explore the suitability of mixing rice-husk and saw dust with ANFO. Presently, about 10% of rice husk/saw dust is being used only to expand the explosive column. The main technical consideration for the use of saw dust/rice husk, has been to reduce the final density and increase the occupancy of explosive in the blast-hole. This not only lowers the detonation pressure in the blast holes, but also reduces cost of explosive without compromising on the fragmentation quality. Besides, with sleeping of the charge there is no substantial fall in the blast quality.

Jan 1, 2006

By Dale Preece, Steven Case, Cassidy McAllister

Simplot Phosphates produces high quality phosphate fertilizer through open pit mining. The operation near Vernal, UT began as a three-pass mining process carried out with drill and blast followed by the combined effort of shovel-truck and dozer material removal. The first two passes removed the overburden and the final pass mined the relatively hard phosphate ore for processing at the mill. Vertical blastholes were employed in all of the mining passes.

Jan 1, 2012

By Robert Hopler

In the annual report under the Explosives Act for 1905, H.M.inspectors state that over 90 percent of the accidents causing death or personal injury occurred in the use of explosives and under miscellaneous conditions to which the controlling provisions of the Act do not apply, and that such accidents caused 43 out of the 50 deaths, and 312 out of 348 cases of injury. The number of accidents grouped under the heading of “Use and Miscellaneous” is less than that for 1904 - viz., 281 against 301. By these accidents 43 persons were killed and 312 injured, as compared with 39 killed and 343 injured in 1904

Jan 1, 2007

By Daniel Roy, Chris J. Preston, Ron J. Elliott

This paper discusses the use of pressure transducers in water filled boreholes in conjunction with surface mounted geophones to gather field data for in-situ dynamic rock properties determinations. A high speed collector is used to capture the data in the field. The calculated P and S wave velocities and rock density measurements are used as input into the Blastcalc program where the values of Young`s Modulus and Poissons Ratio are calculated. The rock properties information is used along with geological structural data and explosives properties in a 3-D blast modelling program to calculate predicted fragmentation distribution and other blast performance criteria based on the proposed blast design.

Jan 1, 1996

By Joseph A. Meyers, Michael D. Stokes

This paper will focus on the use of Deflagrating Cartridges for tunnel excavation in Midtown Manhattan at Grand Central and 42nd Street Station, where the excavation has challenges due to the proximity of existing underground infrastructure and a contract blasting restriction. Skanska and FDNY’s collaborative teamwork successfully used deflagrating cartridges and gathered vibration data to properly predict ground vibrations on nearby infrastructure. In cities like Manhattan, conventional blasting excavation methods can be constrained or restricted entirely by the risk of damage to nearby structures, utilities, and disruption to everyday life on the streets. The introduction of Deflagrating Cartridges to the project offered a promising solution to mechanical excavation being used by providing controlled, precise, and deflagrating rock breaking capabilities that minimized disturbance to the above items. This technology minimizes the risk of vibration damage to preexisting infrastructure due to its reduced velocity of deflagration, making it useful for the location of our project. The team's approach involved numerous test shots to help determine the appropriate loading and timing sequence, as well as to collect data to properly be able to predict vibration on the adjacent structures. The successful application of deflagrating cartridges in the Grand Central area demonstrates their usefulness in logistically challenging underground excavation projects in urban cities. Through careful coordination and innovative use of this technology, the team was able to navigate the complexities of working near existing infrastructure while maintaining high levels of safety and productivity. Overall, our paper will speak to the importance of new technologies like deflagrating cartridges for usage in urban environments while minimizing disruption to the world above and below, the technology of these products, and the outcomes of our vibration data collection. By embracing these advancements, construction teams, owners, and other agencies can effectively address the unique challenges posed by projects in densely populated areas, while maintaining safety and productivity.

Jan 21, 2025

By Jonathan D. Aubertin

The unique nature of rock salt blasting is compared to traditional hard rock practices. Rock salt geomechanical nature is discussed in the context of rock blasting events. A cratering mechanism prevalent in soft rocks is presented and exemplified through a series of single hole blast tests performed in salt deposits.

Feb 1, 2020

By Wes Bender

Considering the current interest in Global Positioning System (GPS) usage, it might be timely to look at a more efficient means of utilizing these instruments. The GPS system currently utilizes 28 satellites (4 are spares) circling the earth in an inclined orbit. Normally at least six satellites are within your area of reception at any given time. The satellites broadcast an extremely accurate time signal and an almanac containing all the satellites’ orbital data. This information is updated regularly as the satellites circle the earth. Your GPS receiver, once it has picked up one satellite’s broadcast, can then determine which other satellites should be available for plotting.

Jan 1, 2002

By David Ziegler

A formal blast plan is sometimes required for projects involving rock excavation. A written blast plan submitted with a bid proposal can also be an important sales tool. A blast plan will cover the basic elements of shot design: hole diameter, spacing, burden, loading, and so forth. Some suggestions are discussed here for additional items or topics to address, including: safety issues, ground control, traffic & site control, public relations, pre-blast inspections, seismic monitoring.

Jan 1, 2003

By David Cheung, S. Paul Singh

"The characteristics of a blasted muck pile can have a significant effect on the productivity and economyof loading and hauling operations. Poorly fragmented and tight muck piles, caused by insufficientdisplacement of the broken rock, lead to higher digging and hauling costs. Therefore muck pile must be tailored to suit the loading and hauling equipment. In order to achieve this objective, it is imperative to understand the relevant muck pile characteristics and factors governing them. In general, muck pile characteristics are governed by the blast design parameters, rock mass geology, explosive characteristics and post-blasting requirements."

Jan 1, 2017

By ISEE

Micrometer Crack Response to Vibration and Weather, by Prof. Charles H. Dowding of Northwestern University, adds to Prof. Dowding’s already important contributions to the industry with his “Construction Vibrations” books. This new book reports and interprets important data on crack response that are essential for differentiating the unseen effect of weather on structural cracking from the usually much smaller effect of vibration. In addition, the book contains detailed descriptions of data collection methodology.

Jan 1, 2010