Search Documents

By Carlos Agreda

"In the present article a case study of ammonium nitrate in mine water is briefly analized and discussed. Causes of mine water pollution from AN are very well identified and emphasized.Some preventative measures, as well as, some methods of monitoring and control to minimize, mitigate and/or avoid mine water pollution are recommended."

Jan 1, 1999

By He Guangyi

During rock blasting in extending deep cutting from Jiu Li Mountain to Dong Zhuang Village in Jiao Zhi Railway line, we have drilled deep hole with large scale diving drilling machine and successfully carried on controlled blasting. This has provided new experiences for rock blasting in extending existing cutting. The aim of this article is to provide an introduction to bench height, blast holes arrangement, powder charge calculation, and detonating technique during blasting.

Jan 1, 1997

By Jack Elorenta

A recent forum of mine operators revealed a continuing strong interest in alternative methods of freeing rock. A Rand Corporation report lists a continuous mechanical machine that would replace drilling and blasting as a priority for mine operators. Meanwhile, mounting evidence documents a dramatic cost benefit in processing where increased blast energy is available. The reasons for this dichotomy may be due to a number of factors.

Jan 1, 2002

By Michael S. Wieland

The stress waves generated during delay blasting in underground or surface mines not only fracture the surrounding coal, rock, or other strata, but also impact delayed charges remaining in neighboring boreholes. This crossing wave interaction is a ubiquitous fundamental damage mechanism, ultimately responsible for numerous occurrences of misfires and flyrock. The hazards and waste from wave-induced malfunctions are Just the recognized tip of the iceberg. Undetected marginal performance of damaged delay detonators and desensitized charges poses a tremendous unresolved problem, resulting in the reduction of mining profits and the certain retention of unwanted risks.

Jan 1, 1988

By Marlyn G. King, Robert L. Martin

Blasting activities in all four pits at Thunder Basin Coal's Black Thunder Mine are focused on cast blasting. With widths varying from 190 feet to 265 feet and bench heights varying from 90 feet to 175 feet, casting efficiencies vary with different geometry's. For example, the percent cast to final in the 200 foot pit is on the average higher than the 270 foot pit. The powder factors are somewhat higher in the narrower pits, thus increasing the cost of blasting. This leads to a very detailed look at the actual benefit of cast blasting and the associated cost of these benefits.

Jan 1, 1995

By Mark D. Kirkbride

This paper outlines the process for designing a hard rock blast in an underground coal mine. The coal mine is located in Western Kentucky and operates four continuous miner units at 7 unit-shifts per day. The mine operates in the Western Kentucky No. 11 Seam with local variations from 4.5 - 5.5 feet seam thickness. The seam has sporadic siderite deposits. Usually these deposits do not significantly interfere with the mining process. When previous siderite deposits were encountered they were small enough to drop an entry for a couple of crosscuts. The blasting plan was called for after a siderite deposit was encountered in the belt entry at about one third of the panel length. The other sides of the panel had been previously mined and sealed so the decision was made to mine through the siderite deposit with the continuous miner instead of abandoning the panel. The deposit was approximately 300 feet in length down the belt entry. Mining through the deposit with the continuous miner was expensive in both terms of production and of wear and tear on the continuous miner. A blasting plan for the siderite deposits was designed to minimize damage to the continuous miner should a similar situation occur.

Jan 1, 1999

By Milton Barbosa Landim, Denise de La Corte Bacci

Statistical methods of multiple regression analysis, trend surface analysis and principal components analysis were applied to seismographic data recorded during production blasting at a diabase quarry in the urban area of Campinas (SP), Brazil. The purpose of these analyses was to determine the influence of the following variables: distance @), charge weight per delay (W), and scaled distance (SD) associated with properties of the rock body (orientation, frequency and angle of geological discontinuities; depth of bedrock and thickness of the soil overburden) in the variation of the peak particle velocity (PPV). This approach yielded variables with larger influences (loads) on the variation of ground vibration, as well as behavior and space tendency of this variation. The results showed a better relationship between PPV and D, with D being the most important factor in the attenuation of the ground vibrations. The geological joints and the depth to bedrock have a larger influence than the explosive charges in the variation of the vibration levels, but frequencies appear to be more influenced by the amount of soil overburden.

Jan 1, 2002

By J Lyall Workman, Peter N. Calder

Flyrock can be a serious hazard associated with blasting. Many surface blasting accidents involving injury result from excessive flyrock beyond the protected blast zone. Numerous cases of equipment damage at the mine, quarry or construction site have resulted from flyrock. Fragments propelled beyond the property limits of the operation have also caused injury and damage.

Jan 1, 1994

By Peter Stamos

In the summer of 1989, Material Service Corporation (MSC) was expanding its Thornton limestone mining operation putting them in close proximity to two shopping centers in Homewood. In other communities, similar expansions had been met with community protests and lawsuits seeking injunctions to stop operations.

Jan 1, 1991

By Rolly Thorpe

Bulk emulsion explosives have been used at surface mines and quarries for many years. Recently, this technology has been adapted for underground use in relatively confined work areas and in smaller diameter blastholes.

Jan 1, 1994

By Zoltan Susanszky

This paper discusses problems encountered when blasting under rivers for pipeline crossings. Many pipelines have recently been laid under the Danube River. Great care had to be taken to determine limits of detonation impulses from blasting operations in order that no damage would occur to structures at the water's edge, boats, and swimmers. Equations were derived from the results of this study which enable prediction of impulse levels.

Jan 1, 1977

By Mike McGill, Steven P. Case, Mark Spaulding

The General Crushed Stone Company at Doswell VA. decided to open a new pit to expand their reserves. The elevation of the property was 136 feet above the present primary crusher. The project required driving twin tunnels under the highway to access the primary crusher from the new property. A shaft was needed to pass blasted rock to the tunnel elevation where it's loaded and hauled to the primary crusher. In addition, a ventilation shaft was required to provide adequate airflow. Dynatec Mining Contractors Inc. Lakewood Colorado was subcontracted to handle the tunnel and shaft development.

Jan 1, 1993

By Chantale Doucet, Yves Lizotte, Alan Cameron

A joint Federal Government-Industry research project on the effect of geology on the fragmentation of rock excavated by blasting in underground developments was conducted at the CANMET Experimental Mine, near Val d'Or, Québec. A total of thirteen (13) blasts were studied from November 1994 to February 1995. The analysis of each blast was divided into three stages: pre-blast characterization, including structural mapping, assessment of Rock Mass Ratings (RMR), Tunneling Quality Indices (Q), blast design documentation; blast characterization comprising blast vibration monitoring and analysis; and post-blast assessment comprising fragmentation assessment by digital photoanalysis, calculation of half cast factors and measurements of bootlegs.

Jan 1, 1996

By Bruce B. Redpath, Thomas E. Ricketts

Scaling laws commonly used for describing or predicting blast motions generated by conventional arrays of blastholes are dimensionally incorrect. The scaling of distance by the cube root of charge weight is correct only for spherical charges, and scaling by the square root of charge weight is incorrect for any charge configuration, although both approaches may result in empirically useful formulas for a limited range of charge sizes. Analysis of motions generated by a large set of underground blasts shows that scaling distance by the square root of the linear charge density, which is dimensionally correct for a cylindrical borehole, yields much more consistent results than the traditional scaling rules. Further, this scaling law is valid right up to the free face of the burden. A significant result of this work is that the peak particle velocity for an array of blastholes is primarily dependent on blasthole diameter and not on total charge weight or maximum explosive weight per delay, which are the commonly used parameters for scaling seismic amplitudes generated by conventional blasting arrays.

Jan 1, 1987

By Jung-Hoon Ryu, Chang-Ha Ryu, Byung Hee Choi, Yang-Kyun Kim

Control of overbreak in tunnel blasting is one of the key factors affecting the construction expenses as well as safety. Overbreak causes an increase in the cost of construction by requiring an additional amount of shotcrete. In addition, blast damage to the final rock face may cause instability and rock fall hazards. For these reasons, controlled blasting is an indispensable routine in tunnel excavation in order to get a smooth face and to reduce damage to the final wall. We have experienced a very poor quality of excavation depending on the tunneling sites although a similar design of controlled blasting technique was applied. Field experiments over 40 rounds were carried out to investigate the cause of the poor results in tunnel blasting. In this paper, discussed are the parameters affecting the overbreak and some findings from the field experiments. Overbreak could be controlled considerably by adjusting some parameters before the efforts of developing a new blasting method.

Jan 1, 2004

By Paulo Couciero

Since explosives are the source of all energy used for rock blast fragmentation and heave, multidimensional effects in the detonation driving zone become essential to better describe the detonation process. In order to use the explosive as an energy source-information for more realist blasting performance simulations, a simple and effective modelling strategy is desirable. Facing this challenge, an engineering approach to two-dimensional unconfined non-ideal detonation is proposed. Based on the elliptical construction of the shock locus, the model combines the axial cylindrical stick Q1D solution with some additional limiting conditions to determine the sonic edge of the charge. For a given set of rate law parameters and velocity of detonation, a complete axial solution is firstly computed through the Q1D model. From this solution, a vital relationship between the axial shock curvature with the shock shape parameters can be stablished. Once this relationship is found, the problem simply reduces in finding the shock shape parameters subject to the sonic edge condition. As a result of this calculation, the corresponding charge diameter can be found. Consequently, the proposed model can map the diametereffect curve by relating the unconfined velocity of detonation with its corresponding diameter. Finally, because of its low computation cost, the proposed engineering approach can be also used for characterizing the rate law parameters by fitting to data from unconfined detonation experiments

Jan 1, 2019

By Peter Moser

The average annual consumption of raw minerals in Europe is 10 ton per person. About 50 % is produced by blasting. For a population of 450 million (including the population from the countries of the new member states) this makes 2.25 billion tons of blasted rock, 80 % being building industry aggregates and industrial minerals. In aggregate quarries 10-15 % of the rock blasted can’t be sold, as the material is too fine, i.e. smaller than 4 mm. This ‘fines problem’ is worse in the quarries of limestone and cement producers where up to 30 % of the material is useless. Thus about 450 million tons of useless rock fines are produced and put on waste dumps every year, i.e. 1 ton/person. This problem is addressed by the research project LESS FINES - “Less Fines production in aggregate and industrial minerals industry” which is funded by the European Union under the project contract G1RD-CT-2000-00438. The project consortium, formed of nine partners from 5 EU countries, works on the following two main research subjects: 1. The determination of the natural breakage behavior (NBC) of the rock mass, which is defined as the particle size distribution curve for a certain rock mass with the maximum uniformity and thus for a given maximum particle size that fragmentation curve which gives the minimum amount of unusable fine material. The comparison between the NBC and an actual blast fragmentation curve allows to quantify the fines reduction potential. 2. The adaptation of explosives properties, charging techniques and timing in order to produce only the minimum, inherently unavoidable percentage of fines. With about 15 full time working persons the project is estimated to be one of the largest blast related research activities in Europe at the time of the project period. The project is coordinated by the Department of Mining Engineering& Mineral Economics of the University of Leoben.

Jan 1, 2004

By Ed Jr Smith, Calvin J. Konya

The purpose of this paper is to describe the case history of a blasting project conducted jointly by Precision Blasting Services and Cherokee Explosives. It is the intent of the authors to show how blasting could be done in controlled fashion near very expensive computer controlled machinery. The job was done in minimal time with no complaints or allegations of damage in spite of the fact that blasting was conducted within five feet of the equipment and with the 32 acre plant fully operational, with machine operators working within 10 feet of the blasting site.

Jan 1, 1986

By Mauro Fornaro, Marilena Cardu, Renato Mancini, Daniele Castano

Tunneling by explosive blasting in civil works isn't merely intended to break somehow a way through the rock, rather to drive a permanent, constant cross section, lined way. The current mechanical excavation v/explosive blasting debate is mainly centered on the concept of the tunnel wall quality; and consequently explosive blasting strategy is founded on contour blasting.

Jan 1, 1992

By J R. "Dick" Daniel

One of the more common tasks in blast management is the adjustment of: shot geometry, explosive energy, and shot timing parameters to achieve changes in blast outcomes and costs. Many of these shot parameters, once a delayed blast is initiated, are modified by the development of new free faces which change the original or static input values to dynamic values. These newly generated dynamic values are easily calculated and find use in fine tuning shot adjustments and in rationalizing blast outcomes in a systematic manner.

Jan 1, 1996