Search Documents

By Dale L. Ramsey

Blasters in the field for years have been faced with the task of plotting blast locations for future reference and calculating scaled distances or seismograph placement from maps,aerial photo's etc.'With the constellation fully operational, GPS provides a satellite signal transmitted to a ground receiver which will display the desired coordinate positioning worldwide, 24 hours a day in any kind of weather conditions. There are a variety of GPS receivers available with varying levels of accuracy. The field trials of a handheld navigational quality instrument for plotting blast and seismograph locations along with other necessary industry related data is the basis of this paper.

Jan 1, 1994

By J Lyall Workman, Peter N. Calder

"Presplitting is a technique mines and quarries may use to produce high quality final pitwalls. Damage from backbreak can be minimized, thereby insuring the final pit walls standat the designed angle. Thus costly excess waste removal is avoided. Safety in the pit isenhanced. Control blasting is an essential component of procedures to maintain the stabilityof final pit walls prone to failure."

Jan 1, 1993

By Marcia Harris, Richard Mainiero

The New York State Department of Transportation recently commenced highway widening and drainage improvement projects in Clarence and Amherst, NY. Drainage improvements including the installation of storm sewer lines required excavation to a depth of 2.5 m (8.2 ft). In September 2002, NYSDOT stopped further blasting when 800 ppm CO was detected in the basement of a house near the blasting site. At the insistence of NYSDOT, the general contractor developed a new blast plan with the assistance of an environmental consultant. The plan provided for the installation of multi-gas monitors in buildings of special concern and/or with basements and residential type CO monitors in all other buildings within 100m (330 ft) of the blast. The multi-gas monitors would be remotely monitored. The plan provided action levels which would ensure public safety. The blast design was also modified to allow for better venting of CO. Blasts were limited to 20 ft lengths. The overburden was to be removed from the rock and blasting mats put in place to prevent flyrock. Approximately twenty feet of trench adjacent to the blast was left open to allow ground movement and gas release. The use of CO monitors was effective to alert occupants of a building to the presence of CO. The most effective appeared to be the residential type CO alarms with digital readouts. They were simple and easy to use and allowed the public to participate in the process. False alarms were repeatedly received with the more sophisticated instrumentation. Residential type CO monitors are preferable to warn people near blast sites. More sophisticated instrumentation should be avoided unless personnel are experienced in its use. A general overview of the blasting and monitoring is presented and discussed. The use and effectiveness of residential type CO monitors and multi-gas monitors are discussed.

Jan 1, 2004

By Bob de Raadt

After a review of the general principles for blasting stacks, the stagnations of two stack demolitions are investigated. The author concludes and demonstrates that MS-delay blasting can be risky under certain circumstances. How this initiation device can still be applied safely to the demolition of stacks is shown in an account of a blasting operation, in which two 106-m (350 ft) -high concrete stacks were involved. The recent discovery of a possible hazard of MS initiation in this field of blasting is an essential contribution to increased safety in blasting tall structures.

Jan 1, 1982

Casting design for bench blasting in surface coal mines is a new focus and a fairly recent success. This study aims at the development of a mathematical model to predict the throw of overburden material based on geological conditions of a bench and charges in blast holes. The procedure, derived on the basis of blasting theories and dynamics of the multiple-particle system, explores the mechanisms of casting rocks into pits. Implementing the model with a computer program is a part of the study. The computer program will supply quantitative data for evaluation. It serves the purposes of verification for the model and, hopefully, field applications.

Jan 1, 1988

By E. A. McCullough, Jackson B. C., S. K. Metz

Public perception is a significant challenge facing the explosives industry. The public often perceives that its needs and interests are in direct competition with those of blasting companies’, leading to conflict between corporations and the community. This misunderstanding lends to unnecessary political and regulatory hardship, and ultimately, social discontent. Although individual corporations implement strategies to address conflict, many of these techniques are insufficient. Consequently, stakeholders resort to expensive litigation. If blasting companies could reduce or eliminate the volume of judicial disputes, valuable resources could be re-directed to more productive activities.

Jan 1, 2015

By Stephen Chung, John Carpenter, Scott Gosch, James Breedlove

While controlling fly rock and ground vibration in quarrying in the neighborhood of a residential area, producing good fragmentation and keeping different grades of material separated in a muckpile are important in maintaining the productivity of quality aggregates. This paper describes a single row production blast for the study of fragmentation and displacement in the grade control carried out at a quarry of Barrett Paving Materials Inc. in Sylvania, Ohio. Digital video imaging was used to monitor the blast-induced motion of the bench face as input to the DMC_Blast (Distinct Motion Code), for the analysis of the formation of the muckpile. The actual digitized blast video and the DMC_Blast simulation are compared. The displacement and mixing of all the inter-bedded limestone layers are made visible in the simulated cross-section of the muckpile. The apparent fragmentation analysed with PowerSieve is also discussed.

Jan 1, 2001

By Bradley C. Paul

Similar rock formations exhibit great variability in resistance to fragmentation during crater blasting. This observation was made during an attempt to calibrate the Kuz-Ram blast fragmentation model for crater blast geometries used in a modified in situ mining method for copper. The KuzRam equation is used to predict the fragment size distribution from blasting and includes a term called the "rock factor" to account for the fragmentation characteristics of the material. A data base of field scale crater shots in oil shale was available to supplement more limited data on copper ores. First, the blast geometry terms of the Kuz-Ram formula were modified to fit field data with various crater blast geometries. Rock factors were chosen to center the predicted curve on the curve representing observed fragmentation. Next, five possible sources of variability in rock factor were investigated: the grade of the oil shale, the aspect ratio of the charge, the type of explosive, the charge depth, and the rock itself.

Jan 1, 1989

By Tom Hale

Developers and blasters are faced with increasing public demand and regulatory restrictions to maintain the lowest possible levels of noise and vibration from blasting operations in populated urban areas. Pyrotechnic products have proven to be a low noise, low vibration alternative to conventional blasting for close-in rock excavation and concrete demolition applications. Pyrotechnic breaking charges often yield 1/10th the vibration and noise compared to traditional explosives, and have been demonstrated to increase public confidence and decreased damage potential where they have replaced explosives, thus allowing new opportunities for work and greater job profitability. This paper presents a practical approach to utilizing pyrotechnic products in various applications including trenching, mass excavation, demolition, and dimension stone production, providing methodology for pattern design, vibration probability and loading calculations. Field research data is reviewed and compared to conventional explosives.

Jan 1, 2008

By Douglas A. Bartley, Davey Bickford, Raphael Trousselle

The long awaited arrival of a high accuracy detonator to reach the explosives end user will provide new opportunities the blasting community to become better equipped and able to improve upon the current approaches and methodologies used in blast design as they apply to the mitigation of adverse effects from blasting. This paper will detail the approach and findings throughout a several month research project to quantify the high accuracy detonator benefits and to mitigate a long standing vibration problem at a hard rock stone quarry in the state of New York. The tests conducted in this study were designed to provide important information as to the relationship between the use of high accuracy detonators and overall blast performance in terms of ground vibration prediction, control and improved rock fragmentation.

Jan 1, 1998

By Ismael Gottreux Vollet, Carlos A. Muñoz Lira, Alejandro Ferrada Vergara

Currently, underground mining of deeper massive deposits with lower grades, harder rock conditions in high strength environments, entails difficulties in caving, fragmentation and seismicity of the ore body. So far, the use of Pre-Conditioning (PC) with Hydraulic Fracturing (HF) has shown positive results in terms of seismic response and caving ability, while preconditioning combined with explosives aims to weaken the rock mass, causing an additional effect on fragmentation.

Jan 1, 2016

By Catherine T. Aimone-Martin, Kristen Kolden

In August of 2013 the USDA Forest Service (USFS) blasted bedrock at the base of a waterfall in Kanalku Creek within the Kootznoowoo Wilderness Area on Admiralty Island in the Tongass National Forest located in Southeast Alaska. The purpose of the blasting was to widen and deepen a plunge pool at the base of a waterfall complex considered to be a partial barrier to migrating sockeye salmon. Drilling and blasting to remove 12 to 15 cubic yards of rock occurred over a two day period.

Jan 1, 2015

By Eduardo Berger

This paper describes a mechanized loading system, the HYDRODOSE, which allows the use of pumpable emulsions in underground mining. It also describes a pumpable emulsion explosive for small diameter holes, HYDROMITE PDB. Included are test results carried out in two Chilean underground mines.

Jan 1, 1991

By T Weaver, R Dick, R Sivakumar, C T. Aimone

A series of small-scale crater tests were performed in concrete and sand in an effort to understand the cratering process in large-scale field blasts. The surface orientation of these tests varied from flat to a 30° slope. In comparison to previous crater experiments in competent oil shale, the crater tests in concrete produced craters similar to those in oil shale after scaling the measurements for differences in the mass of explosives among the experiments. Material strengths and the degree of brittleness had a significant effect on the size and shape of the crater. The small-scale sand tests resulted in some crater features that were similar to large explosive tests in alluvium and soil.

Jan 1, 1986

By Anatoliy Yegupov, Vladimir I. Samoylov, Alexandr V. Startshinov

Access difficulties and unique climatic and geotechnical conditions of mineral deposits in permafrost in the Russian Northeast require specific approaches in the selection and use of explosives.

Jan 1, 1992

By Sharon K. Reamer, Yvan Sifre, Klaus-Gunter Hinzen

"Three case studies are presented that illustrate the successful application of firing timeoptimization (hybrid modeling) in the quarry environment and for a construction site. In allcases, the method requires the measurement of at least one in situ, single hole explosion asa representative model of the desired blast design."

Jan 1, 1993

By A Lance McAnuff, Marcus V. van Bers, Andrew Curic

During the summers of 1992 and 1993, blasting operations were carried out to effect the crossing of two of Canada's better known game rivers, the Nipigon and Winnipeg, in connection with the completion of a third natural gas utility across north-western Ontario. The Nipigon River, crossed in 1992, involved a single fast-flowing channel while the Winnipeg River, crossed in 1993, involved three separate channels.

Jan 1, 1994

By John J. Barnes

The advent of more powerful explosives, increased bench heights, and larger diameter blastholes has necessitated the use of presplitting techniques in sub-bituminous coal mines. The combination of these factors has increased the energy concentration during blasting, producing severe overbreak problems in the final pit walls. Presplitting with large diameter blastholes has proven to be the most viable method of reducing back break in sub-bituminous coal mines.

Jan 1, 1988

By Steven D. Knudsen, Dale S. Preece

The spherical element computer code DMC (Distinct Motion Code) used to model rock motion resulting from blasting has been enhanced to allow routine computer simulations of bench blasting. The enhancements required for bench blast simulation include: 1) modifying the gas flow portion of DMC, 2) adding a new explosive gas equation of state capability, 3) modifying the porosity calculation, and 4) accounting for blastwell spacing parallel to the face.

Jan 1, 1992

By F Hunyadi

The seismic effects resulting from blasting are still a problem today although a great deal of research has been conducted in this field. A great amount of data defining the seismic effects can be collected with the proper instrumentation, however because of the difference in building materials, construction methods and foundations the characteristics of the seismic wave can not be directly correlated to the building response and possible damage.

Jan 1, 1975