Search Documents

By Stephen P. Case, Stephen Castellucci, William Parsons

In this paper, the authors present a step-by-step discussion of dimension stone production at a New England granite quarry. The quarry mines a rare pink granite which is used for facings and panels in the construction of high rise buildings around the world. The discussion includes geological considerations, block layout, drilling, explosives loading, block handling, and mobile equipment utilization.

Jan 1, 1990

By Michael Swisdak, John Tatom

In a quantitative risk assessment (QRA), the ability to accurately model real-world situations is obviously critical. In the end, the model must be able to represent the effects produced by the detonation of the donor and the consequences on the target. The science that goes into such a model must be carefully thought-out and based on as much data as possible.

Jan 1, 2007

By R R. Dimock

A goal of all mine operators is to optimize the breakage of the inplace rock to achieve maximum excavating efficiency. The use of the seismograph at Kennecott Copper Corporation's Nevada Mines Division, open pit mine in Ely, Nevada, has demonstrated that optimum blastability can be predicted by knowing the seismic velocity of the inplace rock. The relationship of seismic velocity to the quantity of the explosive required to achieve adequate breakage of the material can be determined. Once quantified, this relationship can be used by the mine operator to obtain the optimum drill pattern and powder factor for breaking the material to be excavated. A substantial savings in primary and secondary drilling and blasting costs can result from using the seismograph for blastability determination.

Jan 1, 1976

By Richard Arsenault

The production of oil & gas from wells requires method of flow from the producing formation into the well bore. Once the well is drilled it will have casing pipe installed to protect the integrity of the well formations and means of delivery to the surface. Once casing pipe is installed it will be cemented in by pumping cement through the annulus of the casing pipe down to the bottom of the well and allowed to flow outside the casing pipe up into the formation.

Jan 1, 2007

By Dale S. Preece

A discrete element computer program, DMC (Distinct Motion Code), has been used for several years to simulate blasting-induced rock motion. Recent enhancements of DMC's capabilities have included addition of an algorithm that couples together rock motion and gas flow. This allows the user to specify a particular explosive which also specifies equation-of-state and other parameters necessary to model explosive gas flow from the blastwell. Rock loading by the flowing gas is calculated automatically. The mechanism for calculating the rock loading is the subject of this paper. The rock motion effects the gas flow calculation by changing the porosity. DMC is currently being used on a SUN SPARCstation 2 computer workstation.

Jan 1, 1993

By Keith L. Bockelman

The Colowyo mine is a unique surface coal mining operation because it is a multiple seam pit. Using a combination of a shovel-truck and dragline operation, Colowyo mines 8 seams of coal to a depth of 400 ft. Over the past 3 years a number of operational changes have occurred, one of which is the implementation of blast casting. Through this implementation Colowyo has been able to eliminate over one million cubic yards a year, which would have had to be removed by the shovel-truck operation. This has also brought about a significant decrease in the stripping cost per ton within the dragline operation.

Jan 1, 1985

By Richard Dooley

This paper is one sided because it presents the problem, but not the solution. The problem of blisters (bubbles) and occasional tears in caisson liners occurred when blasting and we have not found a conclusive cause nor a preventive solution. (For back ground information, consult Techniques of Precision Blasting in the Excavation of Drilled Piers, by George Mosteller at the Sixth Conference on Explosives & Blasting Technique in Tampa, Florida 1980).

Jan 1, 1983

By John T. Watson, Jim Bailey

Increasing public awareness is probably the single most important challenge faced by any blasting contractor today. This increased awareness usually results in an outcry for tighter regulations and restrictions on those in the blasting industry. Those affected do not often understand the dynamics of blasting and are simply fearful of the unknown. This reaction very often results in more regulations and restrictions which frequently fail to address the real problems.

Jan 1, 1990

By Bin Feng, Xiang Fang, Tao Guo, Fandong Lu

Abstract: Rough set theory (RS) can find useful information from a large number of data and generate decision rules without prior knowledge. Support vector machines (SVM) have good classification performances and good capabilities of fault-tolerance and generalization. To effectively control blasting vibration effect, prediction model of blasting vibration parameters based on rough sets and support vector machines are established. Particle swarm algorithm (PS) is used to dynamically discretize attributes. Then, according to the optimal particle calculated by the PS algorithm, the decision table is established. After eliminating less importance attributes and data, then SVM is trained and established for prediction. The model can deal with both quantitative and qualitative factors such as aperture and cast direction, and analyze their importance to peak vibration acceleration value. The improvement of prediction accuracy is verified by testing data.

Jan 1, 2014

By James W. Reil, Douglas A. Anderson

Common wisdom has it that a blast which breaks rock efficiently should-generate less ground vibration. In practice, however, this idea has not been-rigorously tested. In a previous paper presented at an SEE meeting[1] we described a method for-controlling vibration using delays. The method is very effective in controlling-annoying low-frequency ground vibration. We noted that observed ground-vibration differs in some respects from that predicted by adding single-charge-waveforms.

Jan 1, 1988

By Seung-Kyu Baek, Chang-Ha Ryu, Yang-Kyun Kim

Safety concern is one of the most important parameters in the design of building demolition by explosive blasting. Accidents were sometimes reported due to the flying chips of fragmented materials in building demolition work in urban area. Laboratory experiments were performed to investigate the failure behavior of reinforced concrete pillars under blast loading and to develop an effective protection technique. Sixteen reinforced concrete pillars were constructed with two sizes: 450×450×1800 mm and 600×300×1800 mm. The failure behavior and the flying chip velocities were observed by means of a high-speed camera. Protection scheme was designed and the effects of several protection materials were investigated. Two kinds of non-woven fabrics and wire net were tested as protection materials. The results showed that reinforcing bar was one of the important factors to determine specific charges, and that mesh size of wire net and tied-up method affected the protection of flying chips. Control of gas effects is also a key to the control of flying chips. It was recommended to use both wire net and nonwoven fabrics as primary and secondary protection materials. Such protection scheme was successfully applied to the explosive demolition of 16 and 17-story apartment buildings.

Jan 1, 2002

By Lee Julian

Ground vibrations generated by mine blasting must be controlled to comply with legislation and to protect sensitive local or site infrastructure. The consequences of exceeding imposed limits can range from negative publicity to structural damage to infrastructure. It is imperative that vibrations are controlled without compromising fragmentation and delivery of blasted inventory. General practice is to reduce the charge weight and the blast size as blasting approaches the sensitive structures; however such an approach results in blasting smaller volumes more frequently which places greater pressure on production to meet their targets.

Jan 1, 2014

By Jeff Friedman

This paper addresses certain problems to be encountered when a blasting contractor agrees to provide indemnification. Nearly 100% of all blasting work is performed pursuant to a contractual agreement. Whether the explosives engineering firm works directly for the property owner, or for a general contractor by way of subcontract, indemnification agreements are generally required to protect owners, operators, general contractors, and other interested parties in the event there is subsequent litigation. These contractual requirements are typically referred to as indemnification and “additional insured” agreements. We will address the ramifications of contractual indemnification as well as “additional insured” agreements in this presentation. Some of the aspects of this paper will include:

Jan 1, 2004

By J Edmund Hay, T S. Bajpayee

The Bureau of Mines is developing a test to determine the initiating strength of commercial detonators. Various tests of "detonator strength" are in use, but many of them do not correlate well with each other, and so far, there is little evidence that any of them correlates well with the ability of detonators to initiate detonation in an explosive. Therefore, the Bureau decided to attempt a measurement of the ability of detonators to initiate detonation. To this end, an explosive mixture of adjustable sensitivity was developed. This mixture was nitromethane sensitized with ethylene diamine, the sensitivity being "fine-tuned" by the addition of nitropropane.

Jan 1, 1992

By Tom Short, Bill Beam

Some of the weapons testing shafts at Mercury, Nevada require depths of 1000ft and diameters of 10 feet. The top 40 feet to 65 feet is drilled, blasted and excavated by Large caisson type augers in order to provide vertical working room for the placement of large, oil field type, drilling rigs and the required drill collar.

Jan 1, 1991

By Alastair Torrance

The performance of commercial explosives is clearly influenced by the conditions under which they are used. Mining companies are supplied with Technical Data Sheets which provide details about explosive properties and its suitable application. These are generally produced using laboratory techniques which may not accurately reflect the quality and performance of the product in the field.

Jan 1, 2013

By Frank Sames

Blast vibration and airblast overpressure signals are generally rated and compared only by their maximum amplitude and the principal frequency associated with the peak pulse. The scaled distance concept is often used to predict peak amplitudes and can be applied for blasts in the same area of a mine to evaluate the statistical properties of a set of readings.

Jan 1, 1997

In situ, most Taconite is heavily pre-fractured; because of the high cost of comminution of taconite, maximum fracture of pre-existing blocks is desirable. Sustained borehole pressure plays a significant role in fragmentation, especially by penetrating pre-existing fractures. The distribution of explosive-induced energy in the burden in three dimensions was calculated. Data on the comminution of single particles was used, with the distribution of energies and the distribution of pre-existing block sizes, to calculate fragmentation for a case study. The calculation agreed well with the measured fragmentation. Sequential comminution events are much more efficient than single ones, and enhanced fragmentation may be possible with alternative blasting practices. Some important factors in the dependence of comminution on energy input are discussed.

Jan 1, 1995

By M Siefert, P Moser, T Oberndorfer

"The EC-project ""Blasting Control"" with partners from France, Austria, Italy and Greece dealt with the development of a diagnosis system, which enables blasting experts to investigate in detail on probable reasons of poor blasting results in underground drifting. The system incorporates monitoring of geometric, explosive, vibration and granulometry data. All data are compiled in a database and are provided for direct retrievement by demand of the experts in a graphical environment. This paper focuses on the advantages of such graphical system for both research tasks and applications in real testing situations. It describes the procedure of monitoring and presents a selection of graphical outputs generated during data processing immediately after blasting. Benefits of detailed monitoring in respect of detecting sources of errors are explicated by a actual example of a test series in a mine. The paper will conclude with an outlook onto the scientificresearch work which is planned to be based on the results of hitherto investigations."

Jan 1, 1996

It is a case study of huge rock-mass, loosened out from the parent rock-body, & posing a potential danger to structures down below the slope on which this rock mass was standing. Case was dealt in two phases, by tying/stitching the rock mass to the parent rockbody and breaking it using controlled blasting technique.

Jan 1, 1997