Search Documents

By Matthew K. Coy, Paul N. Worsey

The work described in this paper comprised the master’s thesis work of the primary author and was conducted at the Missouri S&T experimental mine. The objective was to determine if rubber tractor treads could be used as an alternative material for blasting mats. These treads are made from steel cable and vulcanized rubber and are very tough. However, once they reach the end of their life on mobile equipment, they are destined for a landfill, or dump site, because they are too tough to recycle. A potential alternative use for them is as blasting mats. Several discarded treads were obtained from Kolb Grading in St. Louis.

Jan 1, 2015

By Abdulkadir Karadogan, Zikri Keti, Umit Ozer, Mehmet Aksoy, Ulku Kalayci

This paper presents an investigation about how the motions of blast induced vibration waves were affected by the presence of the fault planes. This study was carried out at Espey Open- Pit Boron (Colemanite) Mine in Turkey. Within the scope of the study, ground vibration components were measured for 8 shots using 9 vibration monitors, considering the direction of the fault. Measurement stations were located around the fault line that intersects the open-pit mine in the north-south direction and on different benches along the fault plane. Then, the data of the vibration components obtained from the 77 recorded events were analyzed and the results were presented.

Jan 1, 2012

By Joshua Micah Hoffman, Lifeng Li, Jhon Silva-Castro

Since millisecond detonators were first introduced, at least two variables among others have been more closely considered when timing a mining blast; the accuracy and the precision of the initiation system. Unfortunately, those variables are often ignored when designing timing for mining blast. Despite the lack of consideration of the characteristics of the initiation system, in some situations, e.g., firing a blast hole with one deck and two detonators, changes in the blasting sequence can be the results of the overlapping between blasting charges. The consequences of such overlapping involve flyrock events, fragmentation and diggability problems, and other difficulties affecting the operation of the mine.

Jan 1, 2015

By Dr. Tristan Worsey, Dr. Jhon Silva-Castro

Confinement is an important aspect of blasting. Reducing and increasing confinement can determine whether a blast design performs properly. Over-confined shots usually have poor fragmentation, higher vibrations, and stemming ejection, and unconfined shots usually have a lot of air blast and fly rock. When talking about confinement in blasting, static confinement conditions are typically referenced. Static confinement conditions are ruled by free faces, shot muck, burden, spacing, stemming, hole depth, toe, etc. All these conditions exist in a static state. Static confinement conditions are generally analyzed before the shot takes place, but once the shot starts, the conditions will change according to the sequence and delay of the shot. Once the shot starts, Dynamic confinement takes place. For the authors, Dynamic confinement is the confinement conditions that exist for the charge when it fires and should account not only for the variables included for the static confinement but also for the time and sequence of the shot. The paper explores the theory of dynamic confinement and its role in influencing blast performance. Time and sequence are the main influencers of dynamic confinement and will be the focus of the paper. How to generate the appropriate timing based on blast design, dynamic confinement, static confinement, and geology will also be discussed.

Jan 21, 2025

By Jeffrey W. Lin, Jonathan D. Abbott, Patrick R. Bowden, Tyson J. Plitt

Pentolite is a class of high explosives containing trinitrotoluene (TNT) and pentaerythritol tetranitrate (PETN) with PETN content typically ranging from 40 to 60 wt%. Manufacture involves melting TNT, 80 °C, followed by addition of PETN and trace ingredients to form a homogeneous mixture. Once a mix is ready to be poured, several factors can influence the behavior of the finished product including how long the mix has been at temperature and cooling rate. After the manufacturing process has been completed, storage conditions combined with manufacturing conditions may cause physical changes. Two such changes explored were exudation, liquid exuding from solid boosters, and ratchet growth, irreversible volumetric expansion. Exudation is principally caused by excess water in the process. Ratchet growth is a common phenomenon of nitroaromatic compounds such as TNT where time and temperature fluctuations can cause materials to increase volume, simultaneously decreasing density. Although neither phenomenon affects common attributes such as sensitivity, performance, and shelf-life, both can cause issues in storage and handling. In this study pentolite was cast into various forms under different manufacturing conditions and evaluated over several months of controlled storage conditions including ambient, temperature cycling and elevated isothermal. Subjective and objective measurements were made throughout the evaluation period with the aim to determine the preferred storage methodology.

Jan 21, 2025

By Richard H. Granhom

Detonation pressure, or Chapman-Jouguet pressure, is an intrinsic property of an explosive, and like detonation velocity, is an indicator of explosive performance. Pressure and velocity are also important for calibrating computer codes and for other calculations such as the stress imparted to rock or metal by an explosive. The detonation pressures, P~cj, of many "ideal" explosives have been measured indirectly by recording some hydrodynamic flow variable other than pressure, with P~cj being inferred from hydrodynamics and the assumed Chapman-Jouguet equations. One such method is the difficult and expensive "aquarium technique''.] Commercial explosive manufacturers generally rely on estimates of P~cj generated by computer codes not explicitly designed for non-ideal explosives typically used in commercial applications. Over the last decade, U.S. national and government laboratories have developed in-situ gauge techniques such as the manganin gauge, for direct measurement of detonation pressure. Manganin is an alloy of copper, manganese and nickel, and is ideally suited for use as a pressure transducer because its electrical resistance changes with pressure, but is nearly constant with changes in temperature. A simplified manganin gauge technique adapted for use at a commercial test site is described and some initial results from measurements on commercial emulsion explosives are presented.

Jan 1, 1991

Computational techniques in determining particle size distributions after blasting is getting wide acceptance. A well known approach to extract this kind of information from digital images is edge detection. The number of edge points on a given image increase proportional to the increase of the particles on the image. By selecting a conveniently smooth threshold, counting the signed edge pixels may be a suitable metric further used to quantify the number of particles in the image. Here we propose an image processing algorithm together with Adaptive Neuro Fuzzy Inference System (ANFIS) to efficiently count the rock particles with various sizes on a given surface. To determine a suitable approximation for a mapping between the number of edge pixels and the number of particles, ANFIS is a suitable tool. As a trainable classifier ANFIS proved itself as being better efficient approach than other well known multilayer perceptron classifiers. ANFIS is trained by using convenient training data pairs previously experienced from empirically counted sample images. When given a new image containing the particle information of selected surface, the hybrid neuro fuzzy image processing approach provides satisfying performance on counting the correct number of particles up to the given scale of sizes. In this paper an experimantal study for assessment of particle size using ANFIS is presented.

Jan 1, 2004

By Seung-Kyu Baek, Chang-Ha Ryu, Yang-Kyun Kim

Safety concern is one of the most important parameters in the design of building demolition by explosive blasting. Accidents were sometimes reported due to the flying chips of fragmented materials in building demolition work in urban area. Laboratory experiments were performed to investigate the failure behavior of reinforced concrete pillars under blast loading and to develop an effective protection technique. Sixteen reinforced concrete pillars were constructed with two sizes: 450×450×1800 mm and 600×300×1800 mm. The failure behavior and the flying chip velocities were observed by means of a high-speed camera. Protection scheme was designed and the effects of several protection materials were investigated. Two kinds of non-woven fabrics and wire net were tested as protection materials. The results showed that reinforcing bar was one of the important factors to determine specific charges, and that mesh size of wire net and tied-up method affected the protection of flying chips. Control of gas effects is also a key to the control of flying chips. It was recommended to use both wire net and nonwoven fabrics as primary and secondary protection materials. Such protection scheme was successfully applied to the explosive demolition of 16 and 17-story apartment buildings.

Jan 1, 2002

By Josephine Bones, Robb Larson, Daniel Miler

Avalanches are commonly mitigated through the use of explosives at ski resorts and above transportation corridors. Surprisingly, very little research has been conducted on snowpack response to explosive inputs, and efforts to model this response have been limited. The purpose of this ongoing research project is to ascertain an understanding of the dynamic snowpack response in relation to explosive size and height above the snowpack, coupled with snow conditions, to enhance avalanche control. A system of sensors and computer-controlled data acquisition components has been created to record the movement of snow resulting from the charge detonation. The system records acceleration vertically and radially within the snowpack at two distances from the point of detonation as well as blast air pressure at one location during explosive events. The data at two locations allows inferences to be made about the transmittance and attenuation of shock waves through the snowpack radially as well as vertically. The data shows that raising charges above the surface results in increased snowpack dynamic response when compared to surface detonations. Applying power function regression to accelerations for individual charge elevations, it was determined that both radial and vertical rates of attenuation were not dependant on charge elevation. Additionally, raising the charge also resulted in increased dynamic response at depth within the snowpack

Jan 1, 2012

By Doug Wathen, Philip M. E Thomas

The City of Fort Myers needed to replace a 40-year old 42-inch storm sewer line in downtown Fort Myers with a new 54-inch line to accommodate population growth. The old line had to be kept operational while a new line was installed. the contractor spent two months using a drop ball, a hoe ram, and large rippers trying to break the three to four feet of rock that needed to be removed to accommodate the new pipe. Mechanical trenching was considered but was proven to be overly expensive. On very short notice, Ireco of Florida was asked to design and execute a blasting procedure that would allow this project to proceed. Nearby buildings were over 80 years old, three of them containing antique shops specializing in glass antiquities with attorney offices above them. High water table compounded problems with a 20-year old steel water main and clay drainage pipe 15 feet from the new sewer line. Holes had to be drilled within six inches of the edge of the existing pipe to four feet below the pipe on either side of the pipe and blasted. No interruption in the sewer line flow was to be tolerated.

Jan 1, 1996

By Doug Wathen, Philip M. E Thomas

The City of Fort Myers needed to replace a 40-year old 42-inch storm sewer line in downtown Fort Myers with a new 54-inch line to accommodate population growth. The old line had to be kept operational while a new line was installed. The contractor spent two months using a drop ball, a hoe ram, and large rippers trying to break the three to four feet of rock that needed to be removed to accmmodate the new pipe. Mechanical trenching was considered but was proven to be overly expensive. On very short notice, Ireco of Florida was asked to design and execute a blasting procedure that would allow this project to proceed. Nearby buildings were over 80 years old, three of them containing antique shops specializing in glass antiquities with attorney offices above them. High water table compounded problem with a 20-year old steel water main and clay drainage pipe 15 feet frcan the new sewer line. Holes had to be drilled within six inches of the edge of the existing pipe to four feet below the pipe on either side of the pipe and blasted. No interruption in the sewer line flow was to be tolerated.

Jan 1, 1996

By Charles Dowding, Cathrine Aimone-Martin

This article summarizes an investigation of the structural response of a brick façade home in New Mexico. The subject Ricter residence was located some 1100 to 1400 ft away from an aggregate quarry, and was subjected to a maximum peak particle velocity and air blast over pressure of 0.29 ips and 122 dB, respectively. Superstructure (corner) and mid-wall responses to blasting and human induced activities were measured. An existing exterior crack in the brick work was instrumented to measure crack width response to blasting, human induced activities, and environmentally induced changes in temperature and humidity. Crack and structure response data were correlated with ground velocity and airblast excitations. Amplification of ground motions at the upper structure were calculated and compared with values for typical wood frame structures. The natural frequency and damping characteristics of the structure were determined to compare with measured amplification values. Wall strains produced by bending and inplane tension strains were computed from upper corner structure response and compared to failure strains for drywall and brick veneer. Calculated strains were found to be far lower than those required to crack brick and environmentally induced crack response was found to be far greater than that caused by blast induced ground motion or airblast overpressures

Jan 1, 2005

By Split Engineering Chile Fernando Fernandez

Mathematical modeling in conjunction with mineral characterization is widely used as a method for design and optimization of comminution circuits, to simulate the processes of crushing, grinding and classification. An important input parameter to the simulation models is the Run-of-Mine Particle Size Distribution (ROM PSD). The run-of-mine size distributions due to blasting have a great influence on the performance of a semi-autogenous grinding (SAG) mill. In this paper, a mine case study was conducted where there are four primary geologic units and the material properties between the four units vary considerably. Also, the mixture of the four unit that will be mined at any given time also vary considerably. This presents a challenge in terms of optimizing the blasting for mill production throughout the mine life. As part of the case study, field rock mass characterization, laboratory rock mechanics tests, and laboratory breakage tests were conducted. The field characterization and rock mechanics tests provide material properties used to simulate the effect of different blast designs on run of mine particle size distributions (ROM PSD). The JKSimBlast software was used for these simulations. The rock breakage tests provide material properties used to simulate crushing and grinding performance. The JKSimMet software was used for these simulations.

Jan 1, 2015

By Robert Cefalo

Drill and Blast Engineer Abstract In 2019, the Bingham Canyon Mine, owned by Rio Tinto Kennecott Utah Copper Company, mined through the active underground that dewaters the pit. The active underground required the limitation of vibrations to avoid catastrophic damage or damage that would require work to the shotcrete and additional roof support. The surface design of the current sector next to and through portions of the active underground. The drill and blast group was required to test site law vibration parameters to ensure that vibration limitations were lower than limits set by the underground management team. Seismographs were used to validate the vibration prediction model and check performance of blast in areas of the underground. The bench conditions and limited pounds-per-delay created large obstacles for the blasting team, making it difficult for them to accurately load the pattern with the number of decks in the blast. Methods were used to improve the loading instructions and ensure that each hole achieved pound requirements based off of the distance to the underground that it was designed to protect. The project evolved from start to finish, and the process to estimate distances and loading improved to make the blast a more repeatable process for the size of the project.

By Calvin Konya, Steven S. Spagna, Ed Smith

During Summer 2001, the U.S Army Corps of Engineers awarded a contract to the construction firm of Bush and Burchett of Allen, Kentucky, for the purpose of developing a 13 acre redevelopment site by removing approximately 2.5 million cubic yards of rock (fig. 1). The Redevelopment Site will be the future home for a large portion of the City of Grundy, Virginia. Additional work items include the construction and relocation of 3,000 feet of the Norfolk Southern railroad bed, the placement of 95,000 cubic yards of fill and the placement of 16,000 cubic yards of stone slope protection along the Levisa Fork River. Bush and Burchett received a notice to proceed with construction in July 2001. Currently, the contract is near completion. Current activities include: hauling of material from the Redevelopment Site to the disposal area; placing fill material on the Redevelopment Site, and placing Stone Slope Protection (SSP) along the Levisa Fork river. Approximately one year into the construction highly weathered rock, degraded to near soil- like condition, was encountered in the upstream portion of the excavation. Over one-third of the original cut slope was adjusted and the blasting specifications had to be amended to accommodate for the material that was encountered in this area.

Jan 1, 2005

A series of stemming confinement tests were conducted at a test site near Vernal, Utah. The purpose of the study was to determine the relative performance of various stemming enhancement “plugs”, stem types and loading configurations. The stemming performance was quantified in terms of: . Stem confinement time . Stem ejection velocity . Ground swell velocity . Ground vibration . Air blast . Crater formation Of primary interest was the performance of a new spherical stemming enhancement plug. The initial findings indicate that the hard plastic spheres improved blast performance when used appropriately. Their ability to improve blast performance is reduced when used in over confined or severely underconfined conditions. The study also evaluated the effects of air decking on stemming confinement and explosive performance.

Jan 1, 2000

By James Camp

"During the 1950's a cement plant was rebuilt along a Missouri River bluff. The escarpmentwas composed of inter_bedded shale and limestone, typical to western Missouri. All of theraw materials needed to produce cement had been mined via room and pillar at the plantsite since the late 1800's. Portions of the mine began to fail in the late 60's., and by the mid70's M.S.H.A. declared all the areas where the lower Winterset limestone had beenremoved from the back to be ""unsafe"". M.S.H.A. explained that no work could beperformed in or above these unsafe areas unless the work itself was to render the area safe."

Jan 1, 1993

By Donald H. Matthews

I wish to preface my remarks with the warning that I, in no way profess to be an authority on the U. S. Department of Transportation, Hazardous Materials Regulations, 49CFR Parts 100-199, nor attempt to advise any one on the regulations or how they should conduct their business in relation to the regulations. I merely wish to convey my interpretations of the regulations and some of the procedures adopted by my company to comply with these regulations, with the hope that this information may help others to better understand the regulations and help them formulate their own procedures for compliance. I will cover nine problem areas and furnish sources of information for anyone concerned with explosives transportation.

Jan 1, 1977

By Charles B. Ingram, Neil E. Gehrig

The development of water gel explosive products has been the single most important development in explosive research and development since the invention of nitroglycerine and dyne-mite many years ago. m e Explosives Department of Gulf Oil Chemicals Company has been engaged in the research, development, manufacturing an marketing of slurry explosives and blasting materials for over twenty years. Explosive research and development is being carried out at the Jayhawk Technical Laboratory and the Underwater Testing Facility near Pittsburg, Kansas. There are fourteen manufacturing facilities geographically located around the country to serve the mining, quarrying, and construction industries with a complete line of explosives, blasting agents, and accessories. This paper discusses the Gulf slurry products, their properties, and uses.

Jan 1, 1977

By Dale S. Preece, Stephen H. Chung

"In bench blasting, the distribution of loaded explosives with respect to the burden rock has strong effects on digging especially at the toe area. Blast design often focuses on other results such as percent-cast or fragmentation, sometimes leaving a diggability problem at the toe of the blast that is not discovered until excavation. A method for assessing the influence of blast design on diggability has been developed. This method relates the kinetic energy and rock displacement experienced by the material in the muckpile to its diggability. Simulation of the blast along with the calculation of kinetic energy and diggability is done with the discrete element computer program DMC_BLAST(DMC: Distinct Motion Code)."

Jan 1, 1999