Search Documents

By Anders Lagerkvist, Agne Rustan, Tommy Edeskar

Landfills containing house hold waste produces methane gas during its decomposition. This gas can be recovered and used for heating purposes or as fuel for vehicles. Gas drainage pipes are installed in the landfill and connected to a central suction point. Methane gas is produced over several years until the slots in the drainage pipes are clogged by black mud. And the bottom of the vertical drainage pipe are filled with mud and water. The hypothesis tested in this paper is if blasting in the drainage pipes could activate the production and flow of methane. In the first part of the paper we have studied what maximum linear charge concentration could be used in different size of PE-pipes place vertical on surface and surrounded by air. The results show that the maximum linear charge concentration for single blasts varied between 5-10 g/m, depending on the diameter of the pipe (90, 100 and 160 mm). Maximum charge concentration for the repeated blast varied between 2-5 g/m. In the second part of the paper we study what maximum linear charge concentration could be used in situ for full scale blasting tests in a special prepared test area which later on was dug out after the blastings. Up to 40 g/m could be used without damaging the top of the 160 mm diameter pipes. The increase in methane flow was so low so it could not be measured c4.5 m3/h. The conclusion therefore is that the stimulation of methane flow by explosives is not enough.

Jan 1, 2000

By Zoltan Susanszky

The total available energy in an explosive charge is seldom fully utilized in industrial operations. For this reason more explosive is normally used to perform a job than we would calculate. In an explosive detonation some energy is generated as waste energy which can not be efficiently used. This results in added expense and possible environmental damage. This waste energy can create problems in metal forming with explosives and during commercial underwater blasting operations.

Jan 1, 1976

By Peter Stamos

In the summer of 1989, Material Service Corporation (MSC) was expanding its Thornton limestone mining operation putting them in close proximity to two shopping centers in Homewood. In other communities, similar expansions had been met with community protests and lawsuits seeking injunctions to stop operations.

Jan 1, 1991

By Sami Kara, Marsel Nabium

This paper provides an overview of the solution applied in underground Silver mine in Russia. The paper reviews the dilution problem throughout the entire mining process, and provides a rational approach to underground mine Blast design in order to minimize dilution

Feb 1, 2020

By Bob de Raadt

For a long time industrial underwater blasting has stood in need of a calculation method, for the determination of shockwave-proof as well as shockwave-effective charge distances to objects in water. After a brief discussion of the physical background of the shockwave mechanism in water, the author discusses an empirical theoretical computing method based on the "Bubble boundary" concept. The practical application of this model is finally shown in an account of a few underwater blasting operations in which charge weights of c.1-1000 kg were involved.

Jan 1, 1980

By Sami Kara, Marsel Nabium

As a mining project is developed from conceptual to production phases, there exists a variety of uncertainties and difficulties that affect the operation’s designs and economic values. A notable design parameter to be taken into account is the factor of dilution. Dilution is the waste material not separated from the ore in the stages of mining and is sent to the processing plant. It is defined at the ratio of tonnage waste mined and sent for processing over the combined ore and waste tonnage milled. Dilution reduction is one of the areas that offer metal mines an opportunity to increase revenue and reduce costs, resulting in enhanced profits. Effective dilution control programs require interaction on a multidisciplinary level. This paper outlines recent initiatives undertaken at Polysmetal Silver Magadam Mine to reduce dilution and increase revenue. This paper provides an overview of the solution applied in underground Silver mine in Russia. The paper reviews the dilution problem throughout the entire mining process, and provides a rational approach to underground mine Blast design in order to minimize dilution. The mining companies put a lot of effort into extracting lower grade while minimizing cost. The dilution control assists with achieving this goal. In Polymetal Silver Magadam Mine we succeeded to control more than 20 blasts by keeping almost the same grade measured in the face. The results indicated that using the adequate blasting timing design can help to separate the ore from the adjacent waste in drift blasting with different ore body configuration.

By Bengt Ljung

Manual charging of long upward drilled holes in mines is a heavy and risky job today. Mechanization of this work has been requested for some time by miners, their supervisors, industrial safety organizations and the trade unions, all of whom are interested in improving the working environment. This paper presents newly-developed charging systems intended primarily for charging in connection with sublevel caving and sloping. These systems have been field-tested during 1977 in the LKAB mines in northern Sweden. The results of these field tests and the results of laboratory work conducted to help eliminate the risks involved in charging explosives are also discussed. The equipment being tested (see fig. 1 and 2) consists of a charging vehicle with articulated steering, the PT-60, which has been equipped with a hose feed system mounted on the hydraulic extension boom. From a sheltered position, the operator brings the detonator and primer to the hole opening, after which the hose is pushed in mechanically to the end of the hole. Measuring equipment indicates when and if the end of the blasthole is reached. The operator then withdraws the hose mechanically as charging takes place.

Jan 1, 1978

By Quian Liu

The problem of cross-hole explosive malfunctioning in rock blasting (including sympathetic detonation, desensitization and cut-offs) is a function of delay and spacing in a blast which should be designed to avoid such occurrences. On a delay-spacing chart, the phenomenon of explosive malfunctioning is explained by dividing the chart into different regions, while the shape and size of each region could vary from one explosive to the other. Over seventy blasts have been carried out at the CANMET Experimental Mine to identify the malfunctioning characteristics of specific emulsion, water-gel and dynamite explosives. In each experiment, two parallel blastholes, 32 mm in diameter and 1.7 m deep, were drilled downwards in an underground drift.

Jan 1, 1994

By George E. McCormack

At the time of my visit to the Peoples Republic of China I was employed by the E.I. DuPont Company as a Technical Specialist in the Explosives Department. The purpose of my visit was to observe the use of explosives in mining and tunneling in a coal field 500 miles south of Peking near Hsu Chou in Kiang Su Province. The DuPont Company was preparing a proposal for the sale of a Tovex water gel plant to the Chinese Government.

Jan 1, 1982

By Jim Peterson, Ricardo Freire, Mason Biernat

Variable nature of rock and face conditions, varying execution and changing nature of blasting are making ongoing optimization challenging. Intelligent planning and on-going analytics are required to mitigate variability and convert blasting into a predictable outcome by use of technology. Blasting operations generate a huge amount of data which can be used intelligently for optimization. In this paper, details are provided of a system which is used for blasting data collection in the field – Key details around blast parameters, explosives, initiating system details, video, photographs, vibration and fragmentation are collected in a cloud-based platform. Data can also be collected through a mobility device in the field (even without internet connectivity) and synchronized with cloud-based system. Also, data from various sources can be imported in excel formats in the software including from upstream and downstream processes from blasting. App also gives indication about exceeding of vibration, air blast overpressure, fragment size etc. Thus, making it possible to perform QA-QC before charging and deciding initiation timing and sequence at the blasting site. The data can be processed and analyzed to spot trends, help predict events, and formulate strategies at the design and execution stage. Data gathering of blast parameters, explosive used processing and analysis can be used to optimize operational efficiency, improve safety and environmental controls.

Jan 1, 2019

By Tassilo Baur

Explosives are used in the entertainment industry in a wide variety of applications. Live performances such as automobile races, air shows and the like have incorporated the use of explosives into their programs. Even art work has been created employing explosive materials and techniques. The primary entertainment use of explosives, however, remains in motion pictures, television, theater and related fields where it comes under the auspices of special effects. Much of it falls roughly into the category of demolition, though the object being demolished may range from a cigarette in a person's mouth or clothing worn by actors to large objects such as automobiles, aircraft, or boats. This paper will attempt to provide an overview of the materials and methods by which these special effects are created as well as highlight the unique problems encountered in this field and their often equally unique solutions.

Jan 1, 1992

By Mark D. Kirkbride

This paper outlines the process for designing a hard rock blast in an underground coal mine. The coal mine is located in Western Kentucky and operates four continuous miner units at 7 unit-shifts per day. The mine operates in the Western Kentucky No. 11 Seam with local variations from 4.5 - 5.5 feet seam thickness. The seam has sporadic siderite deposits. Usually these deposits do not significantly interfere with the mining process. When previous siderite deposits were encountered they were small enough to drop an entry for a couple of crosscuts. The blasting plan was called for after a siderite deposit was encountered in the belt entry at about one third of the panel length. The other sides of the panel had been previously mined and sealed so the decision was made to mine through the siderite deposit with the continuous miner instead of abandoning the panel. The deposit was approximately 300 feet in length down the belt entry. Mining through the deposit with the continuous miner was expensive in both terms of production and of wear and tear on the continuous miner. A blasting plan for the siderite deposits was designed to minimize damage to the continuous miner should a similar situation occur.

Jan 1, 1999

By Richard W. Watson, Julius Roth

The Bureau of Mines has recently completed a contract study of the hazards associated with surface mining.! Part of this effort involved an analysis of surface mining accidents associated with blasting activities. For this purpose, 71 reports of accidents investigated by the Bureau of Mines or the Mining Enforcement and Safety Administration (MESA), covering the period from 1962 to 1976, were collected and analyzed. In addition, blasting accident frequencies for the period 1973-1976 were extracted from the central computer files maintained by the Health and Safety Analysis Center (HSAC) in Denver, Colorado. This paper presents a preview of the findings, which are treated in more detail in the final report.

Jan 1, 1978

By B de Raadt

After discussing mechanisms of collapse for the explosive demolition of towers in general and cooling towers in particular, author comments upon a blasting operation in which four cooling towers were involved. The intention of this paper is to present reliable parameters, generally valid for the explosive demolition of reinforced concrete cooling towers.

Jan 1, 1978

By Lex L. Udy

Properties of an explosive which itiuence its performance on rock breakage are analyzed in relation to the rock: hardness and a discussion on the interaction of an explosive with the rock during the blasting process is given. Theoretical concepts regarding ideal and non-ideal detonation are reviewed to explain how the physical and chemical factors of an explosive influence the rate of energy release and its consequence on blasting performance. While a lower velocity of detonation indicates a slowed chemical reaction it does not necessarily mean a loss in energy from the explosive. High density ammonium nitrate (HDAN) can be used effectively in the formulation of modern industrial explosives to slow the energy release rate with its attendant decrease in detonation velocity. Examples of blasting performance using custom formulated explosives with HDAN are presented.

Jan 1, 1995

By Tyler Rockley, Greg Bailey

This paper is an engineering case study of a blast performed on a highly weathered sandstone isthmus in an area sensitive to vibration and airblast, the challenges associated with such a blast, the methods used to understand rock characteristics, the blast design considerations and a discussion of the blast results. The purpose of the blast was to remove approximately 12 feet (3.7 m) of surface material in order to install a pumping station. The isthmus provided several challenges due to the weathering of the rock and multiple open faces with surrounding water. The highly fractured and weathered rock was subject to about ten years of freeze thaw cycles, influx of water and seasonal submersion. As such, all actual rock conditions were indefinite, including fracturing, rock properties, degradation and competency. The isthmus also had immediate neighbors who were unused to the environmental effects of blasting. To help continue to keep the social license to operate in the area, it was important to reduce the ground vibration, blast duration, dust and airblast. These factors required a better understanding of how the rock would respond to blasting. In order to do this, test blasts were performed on the same geologic formation in a different location of the quarry that was less sensitive to vibration and airblast effects, allowing the blast parameters and design to be verified and refined. The test blasts were performed while monitoring vibration, air blast, material movement and overall shot performance, and the blasting parameters were adjusted accordingly. The isthmus blast was performed based on the final design from these test blasts. The drilling and loading of the shot all met acceptable criteria and were comparable to the test blasts. The blast performance, however, was not as expected; the depth impacted by the blast was substantially more than expected. Since the test blasts were performed in the same formation, but in material that was significantly less weathered than the isthmus, the actual effect of this weathering was the only difference between test blasting and the isthmus blast. Thus, these results can be used for future reference to highlight the effects of blasting such highly weathered rock and help instruct the blast design in similarly complex conditions.

By Xu Tianrui, Jin Xiang, Pen Dianhua

Based on the results of research or investigation, this paper describes the causes of and countermeasures for unexpected accidents, such as premature, postponed or spontaneous explosions in blasting practices in China.

Jan 1, 1996

By Terra Dinamica, Frank Lucca

This paper discusses blast design for vibration control in tight construction blasting. Topics include blast pattern geometry, blast design formulas, loading, explosives & initiation selection, and utilizing borehole deviation equipment and lasers, and rules of thumb. The paper will also explore vibration prediction, neighbor relations, and related topics, such as blast plan submittal. Various projects from metropolitan construction blasting operations will be used as examples. Examples include blasting in the inner city, next to pipelines, and in housing developments.

Jan 1, 2005

By Martin L. Smith, Robert L. Hautala

The objective of blast optimization can be approached either in a qualitative sense of designing a blast which will be "trouble free", or quantitatively in the sense of minimizing overall mining costs. Blast design simulators and fragmentation models have become an accepted tool in blasting over the last decade. Numeric simulators are very useful for solving quantitative problems, but are limited in their ability to address more qualitative problems such as post-blast bench condition. Also, current blasting models are limited by the complexity of site-specific blasting and are not functionally suited to mathematical optimization. As a result a great deal of expertise is still needed in optimizing a blast. The following describes the application of an expert system approach to integrating both a symbolic model of the expertise of the blasting engineer for attaining a trouble free blast, and a numeric optimization model relating fragmentation to unit operations from drilling to grinding. Research into this application of a coupled modeling approach to blast design is being carried out to develop a modeling methodology which will provide a suboptimal design for qualitative design goals as well as minimizing blast related costs.

Jan 1, 1991

By Dale Nies, David P. Childs

The open pit gold and silver mining operations in the State of Nevada have historically used simple row by row, echelon, or chevron delay patterns. Common practice has been to use detonating cord trunklines and either detonating cord downlines or nonelectric common in-hole delays in conjunction with surface delays. Several operations use a series of downhole nonelectric delays with an entire row loaded with the same delay to develop similar patterns.

Jan 1, 1991