Search Documents

By Andrew Ritter, Victor I. Montenyohl, Stephen R. Winzer

Thirty-seven open pit production blasting operations have been monitored using high-speed cameras running between 500 and 7000 frames per second. Analysis of the resulting films reveals irregularities in timing including sequencing errors and crowding (holes firing less than 8 ms apart), confirming results of laboratory testing of ms delay blasting caps (Winzer, 1978). Where blasting parameters are otherwise constant and within recommended guidelines (stemming, spacing, burden, etc.), timing problems dominate the overall performance of the blasting operation. Model tests in layered Homalite 100, designed to simulate joint or bedding planes in rock, indicate the importance of the stress waves generated by the explosive in developing the crack network which is ultimately responsible for the fragmentation seen in the resulting muckpile. These mechanisms are strongly supported by high-speed film studies at Pinesburg, Maryland. Experiments in controlling relief in deep shots (where depth approaches the lateral extent of the bench blasted) using borehole geometry and hybrid initiation systems (electronic timer and pyrotechnic delays) were carried out. The results suggest that the 1 me/ft. of burden guideline developed by Bergmann et aI., 1974 is too short, and that much longer times are necessary to optimize fragmentation and muck digability. Longer times are found to reduce noise, vibration, and flyrock.

Jan 1, 1979

By Rafael Tadeu Pinto e Moura, Giorgio De Tomi, Jacopo Seccatore

This paper describes a research and development project in an open-cast mine with the goal to achieve an average P80 of 300 mm (11,8”) in the run-of-mine (ROM) product without altering the existing budget. The project included several variables in the blast design that were not previously taken into account, such as the orientation of natural joint sets in the rock mass, specific energy of the explosive and firing sequence. The new blast design method considered the directions of natural joint sets and determined the drilling pattern and the firing sequence accordingly to favor the movement of the blasted rock along its preferential direction, to reduce its confinement. At the end of the project, it was achieved an average P80 of 304 mm (12”) in the ROM, 50% lower than the one at the beginning of the project. The final blast of the project showed a reduction of 3% of the drill and blast cost, employing the same powder factor and the same drill pattern size used at the beginning of the project. The results achieved show how rock fragmentation is related to variables that are not contemplated in the most common fragmentation models: the firing sequence and the direction of movement in the blast.

Jan 1, 2015

By Dale S. Preece

A carefully designed and controlled in-place destruction experiment was performed on a concrete bunker buried in 4.27 m (14 ft.) of soil. The objective was to determine if the explosive charges would collapse the structure in-place without requiring mechanical excavation. Collapse of the buried structure was fi rst attempted by drilling holes in the soil and placing four 13.38 Kg (29.5 lb) Comp B explosive charges at a depth of 2.13 m (6.7 ft.). The confi guration of the charges when detonated was 2.13 m (6.7 ft.) off the top of the concrete roof and 3.66 m (12 ft.) apart in a square pattern. Detonation of these charges created a crater ~4.88 m (16 ft.) in diameter and 2.13 m (6.7 ft.) deep, leaving ~2.13 m (6.7 ft.) of soil covering. Very limited spalling occurred on the ceiling of the concrete structure as a result of detonating these four charges. The second attempt to collapse the structure consisted of placing another single 13.38 Kg (29.5 lb) charge, identical to the fi rst four, near the geometrical center of the bunker roof. This charge was detonated in the soil cover 100 to 200 mm (4 to 8 in.) above the reinforced concrete roof, collapsing it. Due to the collapsed roof and remaining soil cover, the structure had been collapsed in place, requiring no further demolition. A computer simulation of the above explosive destruction scenario was completed using the computer hydrocode AUTODYN with a granular material model to treat the soil and the RHT brittle material model to represent the concrete. AUTODYN accurately recreated the scenario including the slightly damaged response of the concrete structure to the initial four charges and the collapse of the structure resulting from the second single charge close to the roof.

Jan 1, 2007

By Jamie Delgado, Marco Arelano

The changes of bench angles in an Open pit mine has a strong economical impact in the “mining business”, particularly in its cash flow related both to the decrease as well as to the increase of the global bench angle or the inter-ramp angle. The global vision of bench optimization process currently developed by Compafila Minera Zaldivar (CMZ), includes the interconnection of different processes driving to the completion of the designs. Thus five very influential areas are recognised such as: (1) The physical Surrounding terrain, (2) the strength parameters, (3) the observational model, (4) the acceptability criteria and (5) the operational considerations. One of the important variables affecting this process is Drilling and Blasting (D&B). Increasing the bench angle requires to optimisation of D&B. To achieve this efficiently controlled sub processes must be defined. Three (3) steps can be defined: (a) design parameters, (b) explosive energy distribution and (c) operation results. To control and improve said steps quantitative evaluations of D&B must be performed. One valid evaluation is the “near field vibration monitoring technique” (at bench level). With the application of damage criteria, measurements and modelling of particle velocity a proper definition and optimisation of stages (a), (b) and (c) was achieved, The use of this methodology has enabled to CMZ to successfully increase the inter-ramp angle in three degrees thus obtaining a saving of US$ 36 million in the waste material removed. Also, the efficient control of the bench slopes has resulted in the improvement of the fragmentation operational results. This has resulted in a 26Oh increase in the ore processing by saving energy in the primary crusher due to its performance improvement.

Jan 1, 2001

By Paul Worsey, Dave McCool, Ryan Freeman, Chris Wolters, Rick Hines, John Bowles

Carroll Cave, located in Camden County, in south central Missouri, is one of the most significant caves in Missouri with over 12 miles of mapped passages and over 100 known but unmapped side passages. In the early 1990’s there was a breakdown of the originally excellent landowner/caver relations as the ownership of the only known entrance moved to a new generation and grottos squabbled for control. Subsequently the current owner of the natural cave entrance refused to grant anyone permission to enter.

Jan 1, 2003

By C F. Argo

In the past several years the "Kelly Bar", an innovative device, which incorporates borehole d-rifling and explosives loading into a single detail, has come under scrutiny and criticism. The practical aspects of the Kelly Bar procedure is not questioned, and the system has been highly successful in expediting the loading of explosives in difficult and unstable formations. There have been a number of accidents indirectly associated with Kelly Bar loading and the point in question has become one of safety rather than mechanical feasibility.

Jan 1, 1975

By Curtis Garner

Griesemer Stone located in Springfield, Missouri has supplied aggregate in Southwest Missouri since 1946. In 1954 the decision was made to mine the formation and utilize the mined out area for warehouse space. As advancement proceeded, entrances and small diameter air shafts for ventilation were needed and had to be added. It was decided in 1989 to sink an 8' diameter air shaft designed to move 200,000 cubic feet of air per minute with the help of (4) four 50,000 CFM Loren Cook Fans.

Jan 1, 1991

By Isaac E. "Chip" Harris

Any contractor who agrees to supply materials or to perform services for a sum, is well aware of the importance of proper pre-bid information. Being able to properly plan costs and methods results in profits that allow the contractor to prosper. The paper discusses procedures used in estimating pre-bid cost; in particular, drilling and blasting cost for highways, dams and general construction projects. It breaks cost down into five categories and relates them to a total estimate used in bidding and budgeting a construction project.

Jan 1, 1975

By Gary Anderson, J. P. Remi Proulx

Rio Tinto’s Colowyo Coal Mine produces 2.1 million tons per year in northwest Colorado. Colowyo uses the terrace mining method to recover up to seven coal seams ranging in thickness from 5 to 20 feet. Coal recovery in the 6 foot thick high grade C-seam has recently been challenged due to large variations in the pitch and roll of the seam. As well, some coal damage was seen due to an increased thickness of the overburden consisting of a hard sandstone channel.

Jan 1, 2012

By Lon Santis

In 1923, Ralph Assheton compiled a report for the Institute of Makers of Explosives (IME) on accidental explosions in manufacturing plants. The report chronicles the type and amount of explosive involved in the event and the effects and distances to nearby buildings and workers for over 100 events from 1880 to 1916. Apparently, this report was never published but served as the origin of the IME’s first intra-plant distance table published in Pamphlet No. 3 in 1926. The effort was a parallel effort to the IME’s development of the American Table of Distances. The intra-plant distance table has never been changed by the IME and follows the US Department of Defense (DoD) standard very closely. This paper freshly compiles the data from the 1923 report and analyzes it with modern methods not generally available in 1923. Interestingly, the analysis indicates that the original intra-plant distance tables were established primarily to protect workers from serious injury and that preventing propagation was a side benefit. The data shows that a strong relationship exists between the probability of injury and the traditional K-factor. The data indicate that people in the open are better protected than those inside structures and that barricades reduce risk close to an event. Individuals at the intra-plant distance had a 95 percent chance of receiving no worse than a minor injury. A comparison of the data to explosive event consequence models indicate the models are overly conservative in regards to risk inside inhabited building distances.

Jan 1, 2010

By Thomas A. Gelormino, Ulrich La Fosse

"Deep blasting was used to densify foundation soils for a large manufacturing facility inChicopee,Massachusetts. A 360,000 square foot building, whose construction began inthe summer of 1990, is founded on alluvial deposits up to 90 feet in depth. These deposits are comprised of saturated very loose to loose fine to medium grained sands with traces of silt and gravel. During the building foundation design it was found that to withstand earthquake forces without soil liquefaction, it would be necessary to improve portions of the alluvial deposits by densification. The zone in need of densification extended from approximate depths of 20 to 50 feet. Several conventional densification methods, including vibrocompaction and deep dynamic compaction, were evaluated along with deep blasting. Detonation of 1-3/4 inch diameter charges of 65 percent gelatin dynamite (Atlas Power Primer) installed inside 2-inch diameter PVC casings to a depth of up to 40 feet, was used to achieve the desired densification. This method was selected over others due to its lower cost and decreased construction time. Although used in New England once in1940 for a dam and once in 1960 for a transmission line tower to improve foundation soils, there is no precedent found in the literature for densification by blasting to improve liquefiable soils below a proposed building. Details of a test program and the production blasting, including vibration data are presented. Pre-and post-blasting data conclusely shows an increase in the density of the sand deposit after blasting."

Jan 1, 1991

By Erik Nygaard

During the last years, ammonium nitrate has been involved in several accidents worldwide. This have caused increased focus on security and safety issues and resulted in:• Revised Yara standards • Revised international standards for storage and transportation • Stricter regulations from national authorities in many countries.

Jan 1, 2008

By Jorge Cárdenas, Diego Gamarra

In previous phases of the mine, a landslide resulted in several losses in production delays. The stability of slopes in a mining operation is critical for the sustainability of the operation, as they are exposed to vibrations and damage caused by blasting. Therefore, it is essential to implement controls and innovative technologies to reduce these vibrations levels. This study focuses on the application of low-energy emulsions with lower densities than conventional explosives, developed to reduce vibrations and the energy delivered to the rock mass adjacent to the near blast holes as a buffer row. Near field studies were carried out by embedding triaxial geophones. Vibrations were recorded, and mathematical models of vibration associated with different types of explosive mixtures were generated. This allowed us to determine the benefit of implementing low-density explosives in reducing vibrations compared to Heavy ANFO explosives. The application of low-energy explosives with densities ranging from 0.7 to 0.8 g/cm³ and Relative Bulk Strength (RBS) of 51-65 allows for a 40% reduction in vibrations compared to the detonation of Heavy ANFO explosives.

Jan 21, 2025

By Nolan Eckroade, Nigel Pereira

Wireless electronic blasting systems are a new technology that enable truly wireless initiation through rock, air and water. This is achieved using low frequency magnetic induction waves to wirelessly send a firing command to groups of in-hole primers. Fully wireless initiation not only removes the limitations imposed by a wired connection to each primer in a blast, but also enables users to alter the paradigm of conventional mining techniques to advance operational productivity and reduce personnel exposure to high-risk activities. While initially deployed in underground applications, wireless electronic blasting is now being used in the open cut environment. To capture the early impacts in surface mining operations, case studies conducted at three surface mines evaluated blasts utilizing a wireless electronic blasting system against baseline blasts using conventional, wired initiation systems. The purpose of this paper is to outline the specific learnings associated with wireless electronic blasting in surface mining to date. The paper will include references to these specific case studies as well as benefits realized and applications for the future.

By Lee Wehner, Daryl Kin, John Bolger

The Maumee Quarry, located in the city of Maumee, Ohio, has large in-situ cavities, ranging in size from 3 ft (.91 m) in diameter to over 15 ft (4.5 m). The drill/blast team challenge is to drill, load and shoot the geologically disturbed rock in a safe, cost efficient manner, while in close proximity to a commercial area. A continuous improvement process, managed by a Blast Optimization Team (BOT), was implemented to quantify the innovative explosive loading techniques that have been implemented. Borehole camera monitoring, modified loading practices, the need for accurate drill hole logging and open communications between the drill and blast crew proves critical to the success of the operation. Safe Standard Operating Procedures (SSOPs) have been developed and are strictly enforced for the drill/blast cycle. All blasts are monitored with seismographs and recorded on video to provide detailed information as part of the Blast Management Plan. Despite the geological challenges, the measurement of rock fragmentation index versus loader dig rates has provided near optimal crusher throughput.

Jan 1, 2007

By Andrea Brickey, Ethan Marcoux

The South Dakota School of Mines and Technology (SD Mines), located in Rapid City, South Dakota, is one of only a few universities in the United States that offer a Bachelor of Science in Mining Engineering. The Department of Mining Engineering and Management (MEM) at SD Mines teaches courses that introduce students to concepts related to mining, including a course covering explosives engineering. Students are taught the basics of explosives theory and application in the mining and construction industry through a series of lectures and assignments. With limited field experience, many students find some topics difficult; these include: flyrock, ground vibration, timing, and others. Some US mining schools have an experimental mine in which they can simulate field conditions and conduct hands-on training, but not all universities have such facilities. For those without, teaching certain concepts can be more challenging in a pure classroom environment. To counteract the lack of an experimental mine, the mining department at SD Mines implemented Paradigm (Version 18.4.4984.0; McKenzie, 2017) a computerbased blast modeling software to improve the learning environment.

Jan 1, 2019

By Martti Hagfors, Mervi Hokkanen

The Finnish Defence Forces has destroyed obsolete and spoiled ammunition in open surface mass detonations at Hukkakero fell, in municipality of Kittilä, in Lapland since 1988. The de-struction method was learned from Sweden in 1987. The disposal camp is organized every au-tumn and it lasts four to six weeks. A gross weight of an average charge varies from 150 to 250 tons and the net weight of explosives from 15 to 25 tons. As a booster there have been used 2 to 3 tons of emulsion explosives. The explosives mainly consist of trinitrotoluene (TNT) containing smaller a mounts of amatol and hexotol. The Finnish Defence Forces Tech-nical Research Centre (PVTT) has studied the environmental effects of these mass detona-tions since they began in 1988.

Jan 1, 2011

By Sri R. B Singh

Based on CMRI investigations in nearly 50 mines, the authors have developed two empirical formulae for the effective determination of burden and spacing in any kind of rock deposit. Along with charge loading parameters, decoupling effect and bench height, the equations consider rock characterisation parameter by incorporating 'RQD' i.e Rock Quality Designation. The value of 'RQD' may be obtained either by core recovery using diamond drilling or theoretically from the characteristics of joints or bedding planes. The derived equations may be used in any rock mass under varying geologic and charge loading conditions. The Formulae suggested herein, are explicit, simple in form and easily applicable in field purposes. The values obtained from the present equations are verified against various field data generated by CMRI during the past several years.

Jan 1, 1998

By Erik Nygaard, Klaus Voges

ANFO is the most used industrial blasting agent in the world, and is often used as a reference for comparison of other explosives. It is known to work very well under dry conditions in large borehole diameters, whilst in small borehole diameters increasing amounts of toxic fumes (CO, NO and NOz) can be formed. In underground blasting, problems can also occur with reduced visibility caused by unreacted ammonium nitrate and overall composition of the detonation fumes. ANFO is made by mixing Ammonium Nitrate Porous Prills (AN-PP) and fuel oil. We have measured velocity of detonation (VOD), toxic fumes and visibility after blasting of ANFO in 54x2 mm steel tubes, and the differences are remarkable: By using an AN-PP grade developed for underground blasting and small diameters, the following can be obtained:

Jan 1, 2001

By N Vijay Mohan, K V. Balamukund, G Ananth Ramulu

Jointing of steel rods in reinforced concrete structures needs careful consideration as it renders the structure weak at the joint. The jointing is usually done at sections of structural members, where the bending moment and shear force are least. Jointing is done either by overlapping the rods or welding or by mechanical splicing. A novel method of jointing them is by inserting the two rods in a steel sleeve and cladding it on to the rods by subjecting the sleeve to explosive energy. A rod jointed in this fashion is tested for direct tension and bending when used in a reinforced concrete beam. The test results show that it is an effective method. The advantage is that a number of joints can be made in a single operation.

Jan 1, 1993