Search Documents

By C. T. Aimone-Martin, B. M. Meins

This paper compares response of large urban structures to small charge weight, ultra-high frequency rock blast excitation from contiguous excavation to that of houses to more distant, larger charge weight blasts. Time correlated responses were measured for both structures at the corners, top and bottom of the structures as well as in the foundation rock below the bottom. The comparison allowed the following conclusions: Close-in blasting with direct rock to building wave transmission imposes short wave length excitation which fails to excite the large, massive structures synchronously whereas the more distant blasts do synchronously excite houses. The larger urban structures respond predominantly in wave transmission mode where there is a noticeable difference in time, frequency, phase and amplitude of motions measured at the bottom and top corners of the structure. Excitation motions along the base of the larger urban structures also differs in time, frequency, phase and ampli-tude. The short wave length of the excitation motions leads to attenuation of the peak particle veloc-ity along the base. Ultra-high excitation frequencies, which are much higher than the expected struc-tural natural frequencies, lead to deamplification for all events for the large urban structures.

Jan 1, 2018

By Jerome H. Stofleth

In June of 1998, the DeBruce Grain Elevator was devastated by an accidental explosion caused by the unintentional ignition of grain dust. The DeBruce grain elevator was the largest ‘single head-house’ grain elevator in the nation. It was comprised of 450 cylindrical grain silos, 30 feet in diameter by 120 feet tall, with a centrally located headhouse. Immediately after the explosion, rescue operations were started for seven missing workers. The Federal Emergency Management Agency (FEMA) had taken over operations of the site by day two. On day three FEMA contacted the Washington DC office of the Department of Energy for explosive expertise, who in turn contacted explosives experts at Sandia National Laboratories (SNL) and Los Alamos National Laboratories (LANL). FEMA was looking for guidance in making the decision to downgrade their operation from a rescue to a recovery operation. Based on some chemical equilibrium calculations, and basic explosive engineering techniques, the SNL/LANL team was able to provide the necessary input to allow the decision to be made for the operational downgrade. At this point, only one worker remained un-recovered.

Jan 1, 2004

By P D. Katsabanis, S Kim

A number of small scale fragmentation tests have been conducted to analyze the effects of blasting effort on the grindability of granite, granodiorite, limestone and iron ore. Powder factors were modified, post-blast fragments were screened and drop weight tests were conducted on fragments of different sizes to deliver a variety of specific impact energies. The fragmentation from the drop weight tests has been analyzed to examine the effect of impact energy and powder factor on size reduction. A consistent effect of blasting on the various fractions of the fragmentation distribution has been obtained for all rocks used. The effect of powder factor on the impact fracturing of the rocks has been expressed in a convenient relationship between progeny size, impact energy and powder factor used in obtaining the primary fragmentation. It is clear that explosives consumption affects downstream size reduction; depending on the rock, the effect can be substantial at coarser final sizes but very small in the case of grinding to small final sizes. Differences from the expected trend can be attributed to changes in blast design. As an example, the effect of in-hole collision of detonation waves is analyzed.

Jan 1, 2011

By D Linn Coursen

In the proposed method, the charges are elongated and arranged in one or more arrays. The orientation of each charge in an array, its velocity of propagation of explosion, and the velocity of propagation of vibration in the formation are such that, at an outlying location where vibration is to be reduced, the onset of vibration from explosion of the first negligibly small increment of each charge arrives a finite time before that from explosion of the last negligibly small increment of that charge. The charges of each array are fired in accurately-timed sequence, with the times between initiations chosen so that, at the outlying location, the onset of vibration from explosion of the last small increment of each charge, except the last charge, arrives a negligibly small increment of time before the onset of vibration from explosion of the first negligibly small increment of the succeeding charge. With such timing, vibration may be reduced at the widest range of locations by tilting the boreholes so that the terminal end of each charge is directly above or below the terminal end of the succeeding charge.

Jan 1, 1995

By Thomas E. Ricketts

Limited void volume blasting (LVVB) occurs when rock is blasted into a volume that is not sufficient to let the rock expand to its free-bulking value. The freebulking value is obtained when the rock particles have enough space to separate, tumble and rotate to produce the maximum amount of void possible between the fragments when they finally come to rest. Although bulking value depends on particle size distribution and shape, a typical free-bulking value for uniform, finely broken shale is about 1.67. LVVB occurs in almost every type of blasting used in both surface and underground mining operations. For example, in multiple-row bench blasting for surface mining, the final delays that are designed to fragment the rock furthest from the free-face are generally confined by previously blasted rock which results in a LVVB situation. In underground mining, the blasting is automatically confined and is commonly done intentionally to limited void volume to reduce mining cost and improve safety. LVVB primarily affects rubble bulking and thus the excavation of the broken rock which is related to the productivity and economics of a mining operation.

Jan 1, 1989

By O E. Jr Crenwelge

Recently promulgated regulations governing blast induced ground vibrations in the mining industry contain a frequency criterion as one option for verifying compliance. This criterion is based upon an oversimplified method which assigns the entire peak particle velocity amplitude to one frequency. Depending upon the nature of the vibration time history, it is possible that this frequency may not even be one of the predominant frequencies of the signal. In addition, the criterion does not specifically define the data analysis approach to be used by the industry for obtaining either the amplitudes or the frequencies of the vibration components. And because personnel in this industry generally have little understanding of vibration phenomena, a number of different approaches are currently being used for satisfying the criterion. This paper presents a method for obtaining both the Fourier amplitude-frequency spectrum and the integrated predominant amplitude-frequency components for the vibration record. The method is both physically and mathematically correct and is in common use in a number of other industries. Therefore, it should be of help to regulators, blasters, and consultants charged with developing, enforcing, or implementing ground vibration criteria.

Jan 1, 1988

By Hae-Moon Choi, Sang-Don Lee, Hee Soon Shin, Choon Sunwo, Chang-Ha Ryu, Hyun-Koo Lee

Building tunnels means dealing with what rock is encountered. Relocation of the site of the underground structure is rarely possible. Tunneling engineers and miners have to cope with the quality of the rock mass as it is. Different tunneling philosophies and different rock classification methods have been developed in various countries. Most of the rock classification methods are based on the response of the rock mass to the excavation. Tunnel support requirements could be assessed analytically, supplemented by rock mass classification predictions, and verified by measurements during construction. Rock mass classifications on their own should only be used for preliminary, planning purposes and not for final tunnel support. Design of blast pattern in tunneling projects in Korea is also for the most part prepared according to the general rock classification methods such as RMR or Q. It, however, does not take into account the blast performance, and as a consequence, produce poor blasting results. In this paper, the methods of general rock classification and blast design for tunnel excavation in Korea are reviewed, and efforts to develop a new classification method, reflecting the blasting performance, are presented. Copyright ©

Jan 1, 2004

By Ruilin Yang

Techniques for the study of blast vibrations, such as monitoring, analysis, and modeling are often misused between near field and far field blast vibrations. This paper discusses the differences between near-field and far-field blast vibrations in terms of these techniques. A typical example of a near-field blast vibration problem is a blast vibration in the crest of a new highwall behind a cast blast. In such a case, the blast can be a couple of hundred feet long and the distance from the blast holes to a monitoring station may only be 100 feet or less. In this situation, the size or spatial geometry of the blast is not negligible compared to the distance from the blast to the vibration monitoring point. On the other hand, a typical example of a far-field blast vibration problem can be a quarry blast with a nearby residence house. In this case, the distance from the blast to the house may be several thousand feet. The size of the blast is less than a couple hundred feet long and negligible compared to the distance from the blast to the vibration monitoring point.

Jan 1, 2007

By Franklin J. A, Tam C. Palangio, N H. Maerz

WipFrag systems I, II and III have become the world standard in photoanalysis systems to measure particle sizes. Mines, quarries and excavating contractors can now easily measure blast results and track the progress of optimization efforts. This technology was developed and evolved ~to allow automatic measurements of the size distribution of particles on moving conveyors, in truck boxesand on crusher feeds. Production machinery can now be controlled by photoanalysis results and multiple cameras allow various locations to be monitored by a single system. Blast designs can, be monitored on a shot by shot basis. Changes in delay times, explosives, patterns and hole sizes can be quickly evaluated. Along with this measurement capability has come a heightened awareness of the importance of “optimum size” and uniformity of particles for lowest cost production and material handling efficiency. In the past, savings in the “drill / blast” cycle of the operation were sometimes overshadowed by downstream production costs related to fragmentation. Now total production costs can be compared with fragmentation sizes, which will immediately show the trend towards optimum size for economical production. No cost reduction program can be complete without this critical information.

Jan 1, 1998

By R R. Singh, U K. Dey, S K. Roy

"Commercial explosives being a heterogeneous mixture of many chemical compounds in prefixed proportion, their velocity of detonation (VOD) may vary from batch to batch, due to variations in the proportion of the chemical composition and process parameters even within their tolerance limits. Inherent limitations of measuring methods and human variations during measurement also add to the variation in VOD values determined practically. Therefore, it is customary to define a range of VOD values rather than a fixed value of VOD for a particular explosive.Variations in VOD values of four commercial permitted explosives in India were evaluated under open unconfined condition using Dautriche method and a resistance wire method based continuous VOD meter. Comparative evaluation of VOD values of selected explosives were aimed to check the relative effectiveness of continuous VOD measurement of small diameter cartridged permitted explosives using cheaper co-axial wire instead of recommended costly VOD rods along with the continuous VOD meter. Results of evaluation revealed that continuous VOD of commercial small diameter cartridged explosives could be determined using cheaper co-axial resistance cable with comparatively better accuracy than the most commonly used Dautriche method."

Jan 1, 2007

By Catherine Johnson, Barbara Rutter

The shock tunnel located at the Missouri University of Science and Technology Experimental Mine is 65 feet 9 inches (20.0406 m) in length. The tests performed inside of this tunnel are either arena tests or shock interaction and transfer (SIT) tests. Arena tests simulate a large open air blast, with lower explosive weights, by elongating the impulse of the blast wave. SIT tests are conducted to determine how the produced shock wave interacts and transfers its energy into a target object located at the end of the tunnel. The target used in this research is multilayered, with each layer being a different material. The targets are 2 ft. by 4 ft. (0.6096m by 1.2192m) pieces of Medium Density Fiberboard (MDF), DOW polystyrene foam insulation, and gypsum drywall. The order of these materials varies with each test. This shock tunnel is unique, because the geometry changes along its length. To fully understand how the shock waves are affected by these changes, a working model was needed. The second purpose of this model is to confirm the maximum charge size of 400 grams (14.11 oz.) of C4 that can be detonated inside the tunnel without causing damage to or failure of the tunnel, thus reducing the amount of time needed in downtime and repair. The model predicts pressures in various locations both within the tunnel and the attached target, thus assisting in determining where failures would likely occur. In the process of generating this model, several problems were encountered, including filling the tunnel with air, meshing the complex geometry, and creating the tunnel in a CAD system. This paper will discuss how these problems were solved. A working model was created by using ANSYS Explicit Dynamics and ANSYS Autodyn. The tunnel geometry file was created using SolidWorks and includes the complex geometry changes along with the target and its mount located at the end of the tunnel. The results produced by the model were compared to the field SIT tests. The comparison of the results from both the model and the experimental testing showed a similar trend in the pressure traces.

Jan 1, 2018

By Pierre-Louis Migairou

After a period of development and experimentation ranging over 20 years, electronic detonators have now come to maturity and are becoming the first choice in many diverse applications like tunnelling, civil works, demolition works, quarrying, large scale open pit mining and underground mining. This paper demonstrates the versatility of electronic initiation systems by detailing a number of case studies in several applications as different as their geographical locations, and gives specific reasons explaining the popularity of electronics in each case.

Jan 1, 2009

By B H. A Brown

The components of passive laser survey systems and their relative functions are presented. A general outline of the capabilities and the information available are followed by two case histories. These involve the use of such systems in quarry blasts where loading adjustments and drilling designs were required. Their application in blast casting operations, stockpile measurement, surface and underground construction, and general surveying areas are briefly covered, with comments on the potential for demonstrating a return on an investment in laser survey equipment.

Jan 1, 1990

By Michail G. Egorov

As well as destruction and moving rock, the blast energy sets up a seismic wave in the ground and a shock wave in the air, which can present danger to buildings and disturbance to human occupants. This shock air wave potentially can cause to destruction of a window glass, the window and door frames and partitions of buildings. In modern buildings, distinguished with high flexibility, the shock air wave can cause to the intensive wall vibration, dangerous for these buildings.

Jan 1, 1996

By Leslie Taylor, W. Fourney, Uli Leiste

This paper presents the results from a series of tests conducted to investigate the total vertical impulse delivered to a target plate by a buried explosive charge. The tests were conducted at a very small scale but previous work has shown that small scale testing can predict impulse applied to plates in full scale. Non-deforming plates were used to determine the change in impulse delivered to targets as a result of changes in standoff distance and burial depth changes.

Jan 1, 2009

By R Holmberg, P A. Persson

Recent developments in the methods of measuring rock motion close to the contour at the moment of blasting have given an improved understanding of the extent of rock damage caused by different charge systems. The paper presents the new results and the methods of prediction of damage zones which are used in Sweden for the design of contour blasting rounds. A survey is given of the tools and the techniques for smooth blasting that are now used on a routine basis in Sweden.

Jan 1, 1978

By Marilena Cardu, Mauricio Dompiri, Jacopo Seccatore

Blasting in geological bodies is an industrial process acting in an environment characterized by high uncertainties (natural joints, faults, voids, abrupt structural changes), which are transposed into the process parameters (e.g. energetic transfer to rock mass, hole deviations, misfires, vibrations, fly-rock...). The approach to this problem searching for the “optimum” result can be ineffective. The geological environment is marked out by too many uncertainties, to have an “optimum” suitable to different applications. Researching for “Robustness” in a blast design gives rise to much more efficiency. Robustness is the capability of the system to behave constantly under varying conditions, without leading to unexpected results. Since the geology varies from site to site, and often from bench to bench on each site, setting a robust method can grant better results in varying environments, lowering the costs and increasing benefits and safety.

Jan 1, 2011

By Seokbin Lim

According to published literature, the equation of motion of linear shaped charges (LSCs) has been investigated as early as the 1960s in a few research organizations. However, due to the comparatively low penetration performance, the amount of research has not been extensive, and the use of this device is quite limited in very specialized applications. Traditionally, the equation of motion of an LSCs’ liner shares the same basis as conical shaped charges (CSCs) because they are under the same functional category and generally have similar geometric configuration. However, the nature of LSCs is not quite similar with that of CSCs due to multiple reasons, and they required a new set of equations to properly address their performance. In this paper, we reviewed different sets of approaches in describing the liner collapse behavior of LSCs mostly based on the author’s contributions.

Jan 1, 2014

By Richard Scales, Giles Hellyer, Ian Travers, Dean French, Peter Bellairs

"The Mt Whaleback iron ore mine is located in the Hamersley Province situated about 1OOOkm to thenorth of Perth, the capital city of Western Australia. A small but significant portion of the waste in Mt Whaleback presents problems due to its ability to react with normal commercial bulk explosives resulting in premature detonations, two of which occurred at the mine in 1983 causing great consternation as well as disruption to the mining operation. The techniques and procedures developed to overcome this problem were based on the use of tough durable, acid and heat resistant liners to provide a physical barrier separating the explosive from the rock togetherwith the development of an accurate down the hole remote temperature logging technology. The liner technology was developed due to the inability to produce a reliable inhibited ANFO despite exhaustive mine based testwork."

Jan 1, 1999

By William McFerren, Pragasen Moodley

In contrast to global trends, African, especially South African, surface mining operations have shown a significant rate of adoption of Electronic Detonators (ED’s) over the last few years. Proven benefits of converting to ED’s from pyrotechnic initiation systems have aided this market conversion. These benefits are experienced throughout the mining operation. Benchmarking exercises, prior to the introduction of ED’s, form part of the conversion process and allow for quantifying improvements. Extensive work has been done on quantifying the benefits of converting to ED’s and have shown that results can be reproducible. Improvements have been experienced in many applications and include environmental impact control, improved mining efficiencies, increased cast benefit and improved size distribution. These step changes in blasting results, in conjunction with the adoption of ED technology have aided the rapid conversion of the African surface market.

Jan 1, 2004