Search Documents

By S R. "Bob" Pilshaw

Productivity is the popular "buzz" word that catches the attention of most managers when it is featured in the more popular mining and construction magazines. Engineering Task Forces and teams are formed to take advantage of productivity opportunities in almost all phases of an operation except the drilling and blasting area.

Jan 1, 1988

By Lyall Workman, Jack Eloranta

In this paper results of drill to mill research are examined. It is found that several descriptors of blasting results change when the powder factor is increased. Fragmentation shifts toward a finer distribution. The Bond work index decreases and the product of the t10 model breakage parameters increases. Both of these indicate more softening of fragments. There is research that found large differences in bond work index and other studies that find a much smaller decrease. Even at the lower decrease, however, some savings in energy cost can accrue in hard ores ground to small size.

Jan 1, 2009

By P D. Katsabanis

Image analysis has been proposed to be an accurate and convenient means of measurement of blast fragmentation. The paper compares the results of image analysis to screening using laboratory scale rock piles. The muckpiles ranged from uniform distribution samples to well graded samples following the Rosin-Rammler distribution.Deviations between screened and imaged distributions were observed in most cases due to the loss of fines. Addition of fines in the system improved the result derived by image analysis considerably. It is suggested that techniques for the prediction of fines be evaluated for modifying the size distributions produced by image analysis.

Jan 1, 1999

By Doug Hoy

The scope of the Cliff Avenue Reconstruction Project in Sioux Falls, South Dakota was to widen a two lane highway to five lanes, along with removing and reconstructing both above and below ground utilities located along the project limits. The objective of this paper is to present the blasting techniques used in the rock excavation phase of the Cliff Avenue Reconstruction Project.

Jan 1, 1992

By John S. Manka

Of the various methods used to reduce the density of emulsion explosives prior to detonation; ammonium nitrate prill addition, glass micro-balloon addition and chemical gassing, chemical gassing is the method most often selected by emulsion explosive end users. Chemically gassing emulsions costs less than adding micro-balloons and chemically gassed emulsions have better water resistance than emulsions that add ammonium nitrate prills to reduce the bulk density. Unfortunately, the chemical gassing of emulsion explosives can be intricate and is often more art than a science. To gain a better understanding of chemical gassing, we investigated the factors that may affect the chemical gassing of emulsion explosives. Variables investigated as having an effect on gassing were the pH of the oxidizer phase, the amount and type of nitrogen in the emulsifier, the composition of the oxidizer phase, the use of pH buffers in the oxidizer phase, and how the gassing reagents are added to the emulsion.

Jan 1, 2004

By Peter F. Bayer, Fred C. Drury

This paper deals with explosives regulations in the State of Wisconsin. As has been typical elsewhere, there has been considerable pressure to add additional restrictions over blasting in Wisconsin. What we believe to be a novel approach to the problem has been developed and is being implemented. Members of this Society have been instrumental in this approach whereby the emphasis of the regulations is directed at permissible levels of blasting resultants rather than at specific methods of blasting. It is our intent that this paper serve as a guide to others who may become involved in similar regulatory review in other states.

Jan 1, 1984

By Donelson A. Robertson

Proper coupling between the seismograph transducer and the surface is the most important aspect of seismograph monitoring but probably receives the least attention in many blasting situations. Without good coupling, particle velocity measurements may be higher than actual and frequencies may be lower. If the field data are inaccurate, sophisticated instrumentation and computer programs cannot correct the readings.

Jan 1, 1993

By Paul V. Sterk

In the early 1980's, the Homestake Mine converted from labor intensive methods such as open cut-and-fill mining to Vertical Crater Retreat (\/CR) bulk mining and mechanized cut and fill. This transformation occurred as a result of high costs and low productivity associated with open cut-and-fill mining. Use of Vertical Crater Retreat allowed Homestake to contain waste development rock within the mine to further decrease costs since the voids created from VCR stopes provide a good receptacle. The need to access these voids from surrounding development to facilitate waste dumping precipitated the development of drop raising. This system is cheaper than raise boring because it allows drilling into the top of an open stope without the expense of raise boring cutouts or equipment. It's safer than conventional raising since access from the bottom is not required. Two methods of long hole raising or "drop" raising have been successfully developed at the Homestake Mine and can be categorized as Ring Drill Drop Raising using 2-1/4 inch holes and VCR Drop Raising using 6-1/2 inch holes.

Jan 1, 1991

By Don Thompson

The Minntac Mine drills and blasts approximately 75 million long tons of taconite per year. This requires drilling one million feet of 1 6-inch diameter holes. We are in the process of replacing our old generation rotary blasthole drills (Gardner-Denver 120's and Bucyrus-Erie 61R's) with new generation rotary blasthole drills (Bucyrus-Erie 59R's and P&H 120A's).

Jan 1, 1998

By Marion Smith, Thomas M. Keevin, Dennis G. Wright, Gregory L. Hempen, Joel B. Gaspin, Thomas L. Linton, Gregg R. Gitschlag

"A Natural Resources Working Group, within the International Society of Explosives Engineers, reviewed published environmental effects data, identified data gaps, and prioritized data collection needs relative to underwater explosive use. Six groups of organisms were reviewed: 1) aquatic plants, 2) aquatic invertebrates, 3) fish, 4) amphibians, 5) reptiles, and 6) marine mammals. Studyrecommendations included: conducting basic research to determine the relationship between pressure waveform and mortality where little or no data exist (e.g., aquatic plants, fish, amphibians, reptiles, and marine mammals) and conducting narrowly defined studies where adequate data have been acquired (e.g., aquatic invertebrates). The goals of the recommended studies are to develop the relationship between pressure waveform and mortality/damage in order to construct mortality models. Development of comprehensive mortality models would be extremely useful to the blasting community for assessing environmental impacts and developing strategies for reducing impacts from explosives used underwater."

Jan 1, 1999

By John W. Brown

For seventeen years, I have been involved in surface coal mining in the Mldwest coal fields only to find that once again, I have experienced a problem that was not known to exist in our area. The existence of high sulfur coal seams and pyrite-bearing formations coming In contact with ANFO mixtures has presented yet another potential problem facing the blaster.

Jan 1, 1992

By Corry Goumans

Photos 1 - 4 – Chris Elliott is a rock slope supervisor on a construction project east of Seattle, Washington. His job is to look after a “two man” scaling crew working on the rock bluffs some 300 feet in height along the I-90 interstate just east of the town Hyak. The Washington State Rock Engineers noticed a very large mass of unstable rock along the upper rock face and asked us to take it out. Chris is loading explosives in 1½" ” holes that are 8 to 10 feet deep by 40 feet long with 1¼” x 8” power primer on the unstable rock mass that is about 300 feet above the new road construction. I-90 runs east and west longside the new construction note the containment fence and the ship containers along the highway for protection and Lake Keechelus in the background.

Jan 1, 2014

By Z X. Zhang

In sublevel caving mines, eyebrow break usually gives rise to lower ore recovery and worse safety in the field. Eyebrow break is caused mainly by two tensile stress waves: one from the front surface of a blasting ring, and the other from the roof of the drift. In order to reduce the two waves and finally to reduce eyebrow break at Malmberget mine, we employed two methods: (1) cartridge charge, and (2) double-primers in each blasthole. The two methods were tested in one ore body called ViRi. A total of 10 rings with the cartridge charge and 25 rings with the double-primers were blasted. At the same time a total of 34 ordinary rings were blasted in the same ore body. The result shows that the eyebrow break is 3.0 m for the ordinary rings, 2.3 m for the cartridge charge rings, and 2.1 m for the double-primer rings, respectively. In addition, the ore recovery for the double-primer rings is increased by 3% on the level of ViRi930, compared with that for the ordinary rings.

Jan 1, 2011

By Michael Louis, Charles Dowding

Concern over construction vibration-induced cracking has led to development of a new approach to vibration monitoring called autonomous crack measurement (ACM) and illustrated in Figure 1. This paper describes the concept as well as sensor performance in the first test house fitted an ACM system. Response of three cracks in this concrete masonry unit (CMU) house was measured as part of the system verification. ACM employs a single sensor that measures both weather-induced micrometer changes in crack width and those produced by habitation and ground motioninduced vibration. This comparison is displayed in real time via the Internet without human interaction. Graphic display through the Internet provides a new pathway for communication with the public. Such visual comparison of changes in crack width provides a simple alternative to the present system of comparison of measured and allowable vibration time histories. Measurements reported herein show that weatherinduced response of cracks is greater than that caused by presently allowable construction-induced vibration.

Jan 1, 2003

By Gungor Tuncer, Ali Kahriman

This paper presents the results of ground vibration measurements carried out in Hisarcik Boron open pit mine located on the west side of the central Anatolia near Kütahya province in Turkey. Within the scope of this study in order to predict peak particle velocity level for this site, ground vibration components were measured for 304 shots during bench blasting. In blasting operations; ANFO (blasting agent), gelatin dynamite (priming) and delay electric detonators (firing) were used as explosives. Parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events using 2 different types vibration monitors (1 White Mini-Seis and 1 Instantel Minimate Plus Models). The absolute distances between shot points and monitor stations were determined using GPS. The equation of square root scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity.

Jan 1, 2006

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Savas Gorgun

The principal disturbances created by blasting in open pit mines are vibrations, air blast and fly rock. All of them, under some circumstances, caused damage to structures nearby and apart from this can be the source of permanent conflict with the inhabitations who live close to the operation. Therefore, prediction of ground vibration components is of great importance for the minimisation of the environmental complaints. This paper presents the result of ground vibration measurements induced by bench blasting realised at Can Open Pit Coal Mine located close to the residential area of Can town. Within the scope of this study, in order to predict peak particle velocity and determine the slope of the attenuation curve for this site, ground vibration components were measured for blast events during bench blast optimisation studies over a long period. During the study, while the parameters of scaled distance were recorded carefully, the ground vibration components were measured by means of two different types vibration monitors (White Mini-Seis and Instantel Minimate Plus Model) for 54 blast events. At the end of evaluation an empirical relationship with reasonable correlation was established between peak particle velocity and scaled distance for this site.

Jan 1, 2001

By Hung Tran, Qian Liu, Patrick Andrieux, Dave Counter

Blast damage in open stope mining has been an important concern in controlling ore dilution. Severe damage to the surrounding rock mass can result in the caving of waste rock and/or backfill materials, as well as general instability of the ground. The blast damage study conducted at Kidd Mining Division in 1995 was aimed at measuring the damage zone around blastholes and at identifying other factors which influence the damage. An approach and methodology developed mainly by Blastronics, together with Noranda under a project with the Mining Research Directorate, was adopted for this project. The principle was to combine vibration measurement results with borehole camera observations to derive the blast damage criteria at the specific site. The Holmberg-Persson Equation was used for the regression of near-field vibration data. The damage criteria was examined with both borehole camera observation results and rock elastic and mechanical properties. Details of this methodology, including instrumentation, are reviewed in this paper and an implementation case study of the blast damage evaluation is presented.

Jan 1, 1998

By K D. Sexton, T J. Tope

Manufacturers and users of energetic material (e.g., propellants, explosives, pyrotechnics (PEP)) generate unserviceable, obsolete, off-specification, damaged, and contaminated items that are characterized as "reactive wastes" by definition, and therefore regulated under RCRA, Subtitle C, as hazardous waste. Energetic wastes, to include waste ordnance and munitions items, have historically been disposed of by open burning/open detonation (OB/OD), particularly by the Department of Defense (DoD). However, increasing regulatory constraints have led to the recent reduction and limited use of OB/OD treatment.

Jan 1, 1996

By Rahim G. Haghighi, Calvin J. Konya

Fragmentation is the fundamental concern of rock blasting, serving as a measure of blasting effectiveness. Fragmentation is sensitive to the inter-relationship among the design variables which define pattern geometry. Therefore, the objective of this study was to develop a model which represented a confined bench blast and to investigate the movement of burden-rock as the length to burden (L/B) ratio was varied.

Jan 1, 1985

By H J. MacDonald

An Exploding Bridgewire Detonator (EBW) is an explosive initiator which contains only secondary explosives such as PETN and RDX. It is safer than the normal blasting cap because it requires both high electrical energy and a very fast application of that energy to function

Jan 1, 1981