Search Documents

By N. Paley

An engineering project was undertaken at the Cominco Alaska Red Dog Mine to determine the extent that Semi-Autogenous Grinding (SAG) mill throughput could be increased by blasting differently. The Julius Kruttschnitt Mineral Research Center (JKMRC) blast fragmentation, jaw crusher, and SAG mill breakage models were used to relate changes in the blast design to the SAG mill performance. For optimum performance a SAG mill requires a particular size distribution; a number of large rocks to facilitate breakage by impact, as few as possible middle size rocks that become critical size, and the maximum fines which will pass quickly through an open-circuit mill. Physical constraints of drill and charging equipment size limit the extent that pattern geometry can be changed and the powder factor increased to maximize fines. However, JKMRC research had shown that it appeared possible to increase primary breakage by blasting to such an extent that SAG mill throughput could reach a plateau or even begin to decrease. Modeling was carried out on a range of blast pattern geometries and emulsion explosive blends to determine if a plateau existed and at what powder factor it would be reached. It was found that the relationship between powder factor and grinding throughput was nonlinear. Modeling was also used to compare the SAG mill throughput which could be expected from different emulsion explosive blends to determine which blends should be used in dry and wet holes to provide similar fragmentation. For heavy-ANFO mixtures, the highest modeled throughput was at a ratio of 30/70, with ratios on either side indicating lower throughput. For emulsion blends, the highest modeled throughput was at a ratio of 80/20; however, ratios from 80/20 to lOO/O were similar. Crusher product size distributions were obtained from belt cuts early in the analysis to confirm model predictions. At later stages, actual SAG mill throughput was compared to predicted. The economic benetit from the different blast designs was calculated by accounting for the reduction in recovery due to the higher throughput and the additional drilling and blasting costs. Increasing the powder factor by 150% from the 0.29kg/t {0.58lb/st] being used to 0.72kg/t { 1.44lb/st}, the maximum feasible with mine equipment, could provide a sign&ant net benefit of $3OWyr due to the increased concentrate production. However, because the relationship between throughput and recovery is affected by other factors which were not modeled, a more conservative approach was taken. The powder factor was instead increased by 50°h, providing 45% of the gain. This was possible because the relationship between powder factor and grinding throughput was nonlinear.

Jan 1, 2001

An explosive's velocity of detonation (VOD), can be used to indicate a number of important characteristics regarding the product's performance under specific field and test conditions. A number of new characteristic and transient VOD curves have been identified in the field, which can be used to evaluate explosive performance, control ground vibration amplitudes and frequencies, select the correct amount and type of stemming for use at the collar and in stem decks, eliminate explosive desensitization, evaluate primer performance, design air deck based blasts, evaluate contaminated explosives and to overcome post blast noxious fumes.

Jan 1, 1994

By Calvin Konya, Steven S. Spagna, Ed Smith

During Summer 2001, the U.S Army Corps of Engineers awarded a contract to the construction firm of Bush and Burchett of Allen, Kentucky, for the purpose of developing a 13 acre redevelopment site by removing approximately 2.5 million cubic yards of rock (fig. 1). The Redevelopment Site will be the future home for a large portion of the City of Grundy, Virginia. Additional work items include the construction and relocation of 3,000 feet of the Norfolk Southern railroad bed, the placement of 95,000 cubic yards of fill and the placement of 16,000 cubic yards of stone slope protection along the Levisa Fork River. Bush and Burchett received a notice to proceed with construction in July 2001. Currently, the contract is near completion. Current activities include: hauling of material from the Redevelopment Site to the disposal area; placing fill material on the Redevelopment Site, and placing Stone Slope Protection (SSP) along the Levisa Fork river. Approximately one year into the construction highly weathered rock, degraded to near soil- like condition, was encountered in the upstream portion of the excavation. Over one-third of the original cut slope was adjusted and the blasting specifications had to be amended to accommodate for the material that was encountered in this area.

Jan 1, 2005

By Neal Lee, Braden Lusk, John Silva Castro

One of the most common assumptions regarding the use of ANFO versus utilizing 100% sensitized emulsion is that ANFO “turns over” the muck-pile better, due to the “higher gas volume” supposedly inherent in ANFO. This paper examines this assumption and provides quantitative data for analysis. Total gas volume from each product was evaluated using Orica’s I.D.E.X. Code analysis. This analysis was used to determine if gas volume is a significant contributor to differences in fragmentation and movement between blasts utilizing the two different products. A constant drilling and blasting cost per yard for given cut depth, hole diameter, stemming height and rock type was utilized. The cost per yard was held constant by adjusting patterns considering product, accessory, and drilling costs. Photographic fragmentation analysis, dig rates measured quantitatively through production tracking and time studies and qualitative information about the diggability of the blast provided through video recordings were used to evaluate performance. The data collected during the study is presented and recommendations are made regarding the performance of ANFO and Emulsion holding other variables constant for a limited number of blasts.

Jan 1, 2012

By Donald D. Eilers, Pharis E. Williams, Thomas O. McKnown

The Continuous Reflectometry for Radius vs. Time Experiment (CORRTEX) system was developed by the Los Alamos National Laboratory for determining the energy released in a nuclear explosion by measuring the position of its shock front as a function of time. The CORRTEX system, fielding techniques, and the methods and software for data reduction and analysis were developed over a 15 year period with hundreds of measurements made on nuclear tests and high explosive experiments. CORRTEX is a compact, portable, fast-sampling, microprocessor-controlled system, based on time domain reflectometry, requiring only a 24 volt power source and a sensing element. Only the sensing element (a length of 50 ohm coaxial cable) is expended during the detonation.

Jan 1, 1995

By Goran Cirkovic, Zvonimir Ester, Josip Krsnik

During the reconstruction of the motorway Zagreb-Krapina three reinforced concrete bridges were demolished, for their width was not adequate for the new motorway. Demolition of the three bridges was carried out by blasting as duration of the traffic cut on the motorway and the railway was limited to maximally 4 hours. During that period of time the demolished bridges had to be removed. Therefore, very tiny granulation was requested suitable for loading and not endangering the surrounding structures. Before each of three main blasting, trial blasting were carried out including the seismic measurements registering the seismic effects. The nearest residential building was at the distance of less than 30 m from the place of blasting. Additional difficulty was the fact that by each of the three bridges there is a new bridge, with minimal distance between the old and the new bridge being 30 cm. As each of the bridges is of different construction and of various thickness, particular blasting technique has been prepared for each one of the bridges.

Jan 1, 1997

By Chuck Kliche, Bill Clements

This project involved the removal of the top of an old water supply reservoir tank for the City of Lead, SD by explosives. The general contract called for the removal of the concrete top without damaging the sides or floor of the reservoir. The option of a rock hammer was eliminated, due to the possibility of an unpredictable collapse damaging the sides or floor of the reservoir. Different blasting options were discussed between the primary contractor and the blasting contractor, along with the pros and cons of each. The primary contractor settled on the option of drilling the structure for blasting versus using shaped charges

Jan 1, 2007

By Ruilin Yang

Based on large amounts of field data, this paper evaluates the validity of the above equations. During the evaluation, the different selections of the frequency in the equations were examined with field data. It is found that when they are used to estimate the vector sum values the above equations could result in large deviations from the values obtained directly from the field measurements or the waveform integration. The simple equations may be used to make rough estimations for single components of blast vibration provided that appropriate safety factors are taken into account. For single component vibration, the principal frequency (from ‘zero-crossing’) seems more effective to describe the blast vibration than the dominant frequency (fron FFT) for vibration peak value estimation using the simple equations.

Jan 1, 2012

By Kevin Phelps, Jason Baird, Philip Mulligan, Dominique Nolan

The basic metric for linear shaped charge performance is the amount of cutting distance that the charge can effectively yield given a specific standoff and target. Due to its size and restricted production runs the 10,500 grain/foot (2,232.25 grams/meter) linear shaped charge has had only limited studies that examine cutting performance and standoff. This article covers research regarding cutting performance verses standoff as the charge is applied to common structural steel. Specifically this study uses A36 mild carbon structural steel blocks of 10.16 cm by 11.80 cm by 35.56 cm and standoff distances of 0.5, 1.0, 1.5, and 2.0 charge diameters. Data presented includes the presentation of actual cutting performance numbers, comparison of that data to projected performance based on currently recognized industry guidelines, and a discussion of what may contribute to the performance found in this study.

Jan 1, 2013

By Robert Slivinski, Kyle Hobbs, Michael Stern, John Willox, Brad Jewson

Prairie Mines & Royalty Ltd. produces over 12 million tonnes annually of thermal coal for TransAlta’s Sundance and Keephills power stations from the Highvale Mine. This opencast mine is next to a lake and is surrounded by cottages and farms, which means that blast vibrations and air overpressure have to be kept to a minimum.

Jan 1, 2008

By Unknown

[Executive Director’s note: According to 17th edition of the ISEE Blasters Handbook in its section on trench blasting, “...consideration must be given to the proper venting of gases generated from the blasting. Should those gases spread laterally rather than vent directly to the surface, the gases may travel underground and finally vent well outside of the planned area. Such events may be caused by the strata, soil conditions or root systems, or existing and/or abandoned utilities or other man-made structures. In the worst situation, gases resulting from the detonation such as CO2, CO, and/or NOx may travel through the strata and find their way into basements of nearby homes or businesses. The IME has recommendations on how to minimize this potential problem. Some of the points include removing the overburden and digging the rock immediately after the shot, and drilling vent holes periodically between the ditch and adjacent homes.” The Board of Directors of the International Society of Explosives Engineers has expressed its concern that blasters be made aware of the issue of migration of carbon monoxide resulting from blasting operations. What follows are excerpts from “Carbon Monoxide - The Silent Hazard”, an article that was recently included in the Safety Update, Vol. 20, No. 1, 2001, published by Nobel Insurance Services.]

Jan 1, 2002

By Sarma Kanchibotla

In mineral industry operations the insitu ore is’separated from the waste rock and is subjected to a series ofprocesses to convert it into a valuable product. Profitability of any operation in this industry depends on how eficiently the insitu rock (ore -I- waste) is converted in to the final product and how much value @ice) it commands in the market. Traditionally, the total process in mineral industry is classt@ed into two groups as mining and milling, and optimised independently without considering the impact of one over the other. This paper investigates the impact of mining operations (especially blasting;) on downstream processes and demonstrates the potential benefits of the “Mine - Mill Blasting” approach through simulations and case histories.

Jan 1, 2000

By Raymond V. Adolphson

Use of explosives effectively and safely has come a long way since its discovery and early stages of development. The need to objectively and functionally train personnel in the safe and effective use of explosives became forcefully apparent in the early 1930's in Forest Service work at the start of the Civilian Conservation corps program.

Jan 1, 1978

By Chick Kerkering, Stephen Iverson

Perimeter control blasting is common in civil construction projects but not as common in mining. A poorly designed and executed underground mine development blast design can result in unwanted wall rock damage. This damage increases the risk of rock falls and injury. With the availability of good drilling equipment, it is a simple matter to add the few extra holes needed to change conventional drifting into drifting with perimeter control.

Jan 1, 2008

By Larry Mirabelli, Gerard J. O'Brien

"The construction of the Third Harbor Tunnel is a key element of the Central Artery TunnelProject. The tunnel is to traverse Boston Harbor directly linking South Boston to EastBoston. The tunnel is a cut and cover tunnel as opposed to a bored tunnel. The cutdimensions are 95' wide, 110' deep and approximately 4000' in overall length."

Jan 1, 1993

By Francis O. Otuonye

The results of an ongoing study to determine the response of full contact rock bolts to shock waves due to blasting are presented. A time domain systems modeling and analysis technique was used to identify the axial and bending response of the bolt when explosives charges are detonated at close-in distances.

Jan 1, 1993

By Winfried Rosenstock, Hans-Jochen Blatte

"The guidelines of fire-fighting strategies have to be rewritten, latest since theYellowstone-Fire.CF- and S3- procedure are developed to achieve firelines of 500 ms/ h length and 100 mswidth per unit. Thereby two stretched charges burried in different depth and fired delayedin one round covering 50,000 ms2/ h with non-combustible, natural material (soil) at oncein seconds."

Jan 1, 1993

By Robert B. Hopler

This paper reviews, from the historical standpoint, the development of the commonly-used terms such as "No. 6 and No. 8" with regard to detonator strengths. The origin of the strength terminology is reviewed, and the many methods developed to compare the strength of one detonator to another are described, with the good and bad points of each method outlined. The "miniature cartridge test," very highly regarded by both the U.S. Bureau of Mines and Institute of Makers of Explosives in the 1930's and early 1940's, is described in detail, as is a test developed and used by IRECO.

Jan 1, 1992

By Michael Beattie

A large open-cast limestone mine had its blasting operations severely restricted by the imposition of limiting PPV levels to protect a water pipe-line passing through the mine property. Attempts were made to measure the strains induced in the pipe by ground vibrations, so that a less restrictive blasting limitation could be established on a scientific basis.

Jan 1, 1992

By Paul Downing

While safety and security have always been concerns of the U.S. explosives community, events throughout the world during the past few years have caused us to re-examine our industry’s potential vulnerability and change the way we do business on a day-to-day basis.

Jan 1, 2006