Search Documents

By Jerome H. Stofleth

In June of 1998, the DeBruce Grain Elevator was devastated by an accidental explosion caused by the unintentional ignition of grain dust. The DeBruce grain elevator was the largest ‘single head-house’ grain elevator in the nation. It was comprised of 450 cylindrical grain silos, 30 feet in diameter by 120 feet tall, with a centrally located headhouse. Immediately after the explosion, rescue operations were started for seven missing workers. The Federal Emergency Management Agency (FEMA) had taken over operations of the site by day two. On day three FEMA contacted the Washington DC office of the Department of Energy for explosive expertise, who in turn contacted explosives experts at Sandia National Laboratories (SNL) and Los Alamos National Laboratories (LANL). FEMA was looking for guidance in making the decision to downgrade their operation from a rescue to a recovery operation. Based on some chemical equilibrium calculations, and basic explosive engineering techniques, the SNL/LANL team was able to provide the necessary input to allow the decision to be made for the operational downgrade. At this point, only one worker remained un-recovered.

Jan 1, 2004

By Dale Preece, Mike Stern, Steve Piercey, Ayman Tawadrous, GC Zhao

The McArthur River uranium mine in Saskatchewan, Canada is the world’s largest high-grade uranium mine. It has employed a freeze-wall system consisting of multiple freeze pipes to control the large quantities of water encountered during mining.

Jan 1, 2011

By Inc. The HDH Group

The Alternative Risk Market is defined as the segment of the insurance market that is made up of self insurance, risk purchasing groups, risk retention groups and captives. It is commonly referred to as the alternative to the traditional market, even though more the majority of companies today are insured through the alternative risk market than the traditional market.

Jan 1, 2007

By Stephen Mansfield

In metalliferous mining operations, subdrill is that portion of the blast hole that is drilled below the target grade elevation, and in most cases loaded with explosives. Its primary aim is to enable efficient excavation down to the target floor level. Subdrill is often described as being expensive and that excessive subdrill should be avoided, as it can result in damage to the subsequent floor, lead to difficult drilling conditions and higher vibration levels. As a result, many operations aim to apply the bare minimum amount of subdrill in order to excavate to the target floor

Feb 1, 2020

By N. Skopak, C. Aimone-Martin, J. Redyke, B. O. Meins

PipeBlast is a spreadsheet-based calculator based on research conducted by Southwest Research Institute (SwRI), used by the pipeline industry to determine if proposed blasting planned near existing pipelines can be safely executed. The two factors determining “safe” are blast-induced pipe wall hoop stresses and predicted peak particle velocity (PPV) at the pipeline. Although methodology used to predict hoop stresses is somewhat sound, predicted PPV amplitudes are highly exaggerated based on inappropriate attenuation models developed using spherical explosive charges of limited charge weights, placed in soil adjacent to model pipelines that do not represent rock blasting. Hence, pipeline companies readily reject well-design blasts and limit scaled distances far beyond what is reasonable and cost-effective to pipeline owners. Full-scale trench blasting in rock was conducted near a 24in (711mm) diameter operating API 5L X70 grade steel pipeline in Texas to compare PipeBlast model predictions with a Ground Strain Model (GSM) based on field measurements of ground motions on the surface and at the pipeline springline. Results of the GSM were compared with pipeline strains measured using wire gauges mounted on the Springline. The comparative results showed that a site-specific velocity propagation model provided good estimates of ground strains that are replicated on the pipeline walls in terms of hoop and longitudinal strains. Trench blasting 28ft (8.5m) from the pipeline produced ground motions of 7.6in/s (193mm/s). At this ground motion amplitude, the factor of safety defined as the allowable stress divided by the combined operating and blasting hoop stresses was reduce from 3.04 in the absence of blasting to 2.98. This paper explains the research and findings on which PipeBlast is based and presents an alternative approach to predicting blast-induced pipe wall stresses based on site-specific velocity propagation measurements and a ground strain model.

Jan 1, 2024

By Hans-Peter Rossmanith

Fracture mechanics (Atkinson 1987, Broek 1988, Rossmanith 1978-2002, 1983, 1997, Kanninen & Popelar 1985) and wave propagation (Graf 1975, Rinehart 1975) form the main ingredients in the new electronic detonator based blasting technology. The full potential of using short delay initiation timing in bench and underground blasting can only be exploited if the underlying physical processes are properly understood. From a structural geology point of view, in many open pit mine operations, blasting is performed in incompetent and/or loose rock. Under such conditions the stress waves produced by blasting very quickly dissipate in the rock mass and often their energy cannot effectively be put to work. This contribution shows the effect of open and closed joints – and to some degree also faulting – on the blast wave field and shows the influence of structural geology on the blasting result. A simple engineering method which combines wave propagation and impact mechanics is developed in order to assist the non-scientifically trained blaster in understanding blasting in blocky rock formations. Extensive use will be made of the so-called Lagrange diagram which was introduced in detail in the author’s previous lecture at ISEE 2003 (Rossmanith 2003). This presentation can be considered a continuation of the 2003 presentation.

Jan 1, 2004

By Robert Hopler

Although electrical instruments were being widely introduced into the study of seismic tremors, attempts to understand and quantify shocks from blasting continued to use rather primitive methods well into the 19th century.

Jan 1, 2007

By Chris Searing

An underground room-and-pillar limestone mine in Western Missouri acquired a new primary crusher, physically larger in every dimension than the unit it replaced. Due to the space constraints within the mine, resetting the truck dump and feeder to account for the larger crusher was unfeasible. Mine management determined the most practical solution was to increase the available area for the new crusher via blasting. Fitting the new crusher into the existing area required the removal of 6 feet (1.83m) of limestone from the original floor grade. Blast parameters had to be designed to effectively break this shallow depth of rock while controlling movement to avoid contacting the mine back 23 feet (7.01m) overhead, an apron feeder 13 feet (3.96m) above the southern extent of the area, and the original crusher which was still in place 15 feet (4.57m) from the first pattern. Additionally, work needed to be completed within an aggressive schedule set forth by the mine, allowing little room for delay or error. This paper will examine the efforts taken to safely and effectively blast the rock while protecting nearby equipment and integrity of the mine back. Subjects covered will include blast design, adjustments made to account for drilling and equipment-related constraints, and how seemingly small changes in load parameters can significantly impact performance with small-diameter blast design.

Feb 6, 2023

By Peter Moser, A. Gaich, E. Grasedieck Zechmann

In The SMX Blast Controller is a novel tool for precisely controlling the geometry of a blast based on the technology of 3D imaging. It enables to derive precise information about the geometry of the face of a bench in a quarry from a pair of stereoscopic images taken from the bottom level of a bench with a calibrated standard digital camera. Apart from staking out the blast position with delimiters that mark the area to blast and taking then two images (freely), no further actions are required which allows performing the data acquisition without requiring any surveying skills. The 3D image generation and blast planning does not require special computer. It is estimated, that every blast foremen is able to work with the system after a one-day training as the system includes a high grade on automatism. The software package allows the blast foreman to design and stake out a blast, based on provided geometric values, such as burden, side spacing, hole inclination, sub-drilling, row number & distance and drilling pattern. The software connects these values with the 3D information acquired by the digital images. All the drill & blast information can be used also for blast documentation. The SMX Blast Controller overcomes also the problem of doing the back transfer from maps derived by surveying into nature as the resulting 3D image and all the information associated to it (hole position, etc.) can be correlated with the nature by visual comparison and the help of a single reference line, defined by two points. The system is designed to be used also in small to medium quarries. It can help, that the control of the geometry of the bench face and the precise design of the charge of the blast on a borehole per borehole basis will become an accepted daily routine.

Jan 1, 2006

By Deepak Vidyarthi

This paper deals with the significance of Explosive Energy in the optimization of blast design parameters, and the benefits emerging out of it. It is based on the original work done by the author in developing and successfully implementing a site-specific software package on ‘Blast Design Optimization’ at Kudremukh Iron Ore Mine in India with a production level of 22.5 million tonnes of crude ore and off-take of Explosives of approximately 5500 tonnes per annum. The software package has yielded tangible results in effecting reduction in Explosive Consumption, substantial savings in the Cost of Explosive, besides Environmental Improvements by way of attenuation of Blast Induced Ground Vibrations as well as Air-Blasts. By carrying out regular ‘Regression Analysis’, and determination of the Rock Constants, it has been possible to further develop software packages as well as prediction curves for prediction of Peak Particle Velocity, Safe Charge of Explosive, Air-Blasts etc. A model has also been developed for the prediction of ‘Fly Rock’ although at KIOCL, fly rock does not pose any problem.

Jan 1, 2006

By William Reisz

Managing the blast site at almost any operation can be a daunting task. There are so many details that must be observed, understood, and acted upon. It goes without saying that there are no two locations that have the exact same challenges and concerns. The level and the extent of these challenges can vary widely.

Jan 1, 2014

By Donald Thompson, Jessie Bonner, Ileana Tibuleac

Predicting ground motion from complicated mining explosions is important for mines developing blasting programs in regions where vibrations must be kept below certain levels. Additionally, predicting ground motion from explosions in complex 3D media is important for source size estimation for nuclear treaty monitoring. Both problems have been addressed under the development of a new series of programs including: 1) Generalized Fourier Methods to generate synthetic seismograms (Green’s functions) in 3D media for a moment tensor source implementation and 2) MineSeis3D, a program that simulates seismograms for delay-fired mining explosions with a linear relationship between signals from small size individual shots. To test the programs, three-component seismic recordings of three production shots at an iron mine in northern Minnesota were compared to synthetic waveforms in 3D media. Comparison of the observed and synthetic waveforms shows promising results. The shape and arrival times of the normalized synthetic and observed waveforms are similar for most of the stations. The synthetic and observed waveform amplitude fit is best for the vertical components in the mean 3D model but not as promising for the transversal components. The observed effect of spall on the waveform spectra was weak in the case of fragmentation delay-fired mining explosions. Commercial applications of the code could provide data needed for designing explosions that do not exceed ground vibration requirements posed by the United States Department of Interior, Office of Surface Mining.

Jan 1, 2005

By A B. Opperman

For many years explosives energy has been utilized in mining and construction as well as many other applications which are vital to our way of life. Many types of explosives have made their contribution as technology has moved forward. One of the best known was dynamite, which for many years was the mainstay of explosives users. Although dynamite had many advantages over its predecessors, it had the principal shortcomings of being somewhat hazardous to handle and was known as a headache producer.

Jan 1, 1975

By W. J. Birch, D. Leckenby, R. Farnfield

The use of electronic detonators to improve fragmentation is becoming universally accepted. However their use in limiting peak particle vibrations levels is still in its infancy. Most of which is anecdotal, in that few actual scientific studies have been carried and published. This paper details the research work carried out at a limestone quarry in the County of North Yorkshire in Northern England. Here a series of blasts were carried out some used non-electric detonators whilst others used electronic detonators. The majority of blasts were carried out at the same burden, spacing and deck charge weight loadings. Initially, the key variable was the difference in detonator type and then leading on to using the electronic detonators at specific exact different detonator timing intervals. Later the study was extended to include double row as well as single row blasts.

Jan 1, 2007

By Ralph E. Burnham, Jeff Taylor, Jonson Montgomery, J. Kelly Ratliff, Rennie Montgomery, Martin Brashear

Top priorities for all blasting companies and individual blasters are risk management, safety of company personnel and the general public, regulatory compliance, and liability protection. On a daily basis, hundreds of shots are detonated by well-trained, skilled, and experienced blasters without incident. Unfortunately, accidents inevitably occur, which is why blasting is considered an “ultra hazardous” or “inherently dangerous” activity from a legal perspective. Despite countless regulations, recent advances in technology, improved training, ongoing research, and improved communication in the industry, mistakes and the resulting incidents continue to occur during blasting operations. These result in dangerous or deadly flyrock, site security lapses, increased complaints, blast damage claims, and lawsuits, which lead to increased insurance costs and other financial tolls for blasting companies. In life, lessons learned the hard way are rarely forgotten. The same is true in blasting operations. Blasting missteps and the resulting events are often the best catalysts for improving risk management and thereby reducing accidents, liability, and financial tolls. This paper provides a summary of two incidents, one safety and the other liability related, and the errors that resulted in a fatality in one case and a multi property lawsuit in the other. The two incidents provide examples that serve as a case study for lessons learned the hard way in blasting operations and offer guidance for the considerations that blasters and blasting companies should incorporate into daily operating procedures.

Jan 1, 2018

By David Davison

Metafex®* is an inert material that is more energetic than explosives when activated. Because Metafex is inert until activated (a moment before use), it can profoundly change the logistics of systems and processes that require energetic materials. We have obtained positive test results for a Metafex configuration (called a flat pack) that operates at the practical voltage of ~20 kV. We describe the outcome of the testing and potential uses of the material.

Jan 1, 2006

By Thomas Bakley, Rob Lee, Jay Rodgers

The present state of technology in Controlled Blasting uses standard explosives’ products to create a crack between holes along a desired line of break. The resulting pre-split, post-shear or cut line is often of variable quality with unwanted damage at right angles to the desired cut line. A new concept in Detonating Cord manufacturing has provided a radically different performing explosive. This new Cord has reduced the Velocity of Detonation by more than a third. It changes the Detonation Pressure proMe of Detonating Cord to a lower and longer sustained pressure pulse. In addition, it develops more gas than conventional cords. At the same time it maintains all of the handling and reliability advantages of conventional Detonating Cord.

Jan 1, 2001

By Barbara Rutter, Phillip Mulligan

This research investigates how changes in shock tunnel geometry affect the pressure versus time waveform. The Large Arena Test Simulator (LATS), which is composed of four different rectangular sections connected by three expansion sections, was used to determine how the changes in geometry affect the shock wave profile.

Feb 1, 2020

By Frank Hirthammer

Over the past few years, development and implementation of digital logistics solutions has convinced users of many additional advantages of this technology. Barcode labeling and reading increases the company’s efficiency and safety by reducing handwritten documentation and preventing misinformation. Sustainable information and productivity management is a significant advantage in competition. Since manufacturing information is tracked throughout the whole supply chain until the final consumer, all processes become transparent what ensures efficient risk tracking, correct disclosure to authorities (if required), and the compliance with company rules.

Jan 1, 2018

By Stephen Mansfield

In metalliferous mining operations, subdrill is that portion of the blast hole that is drilled below the target grade elevation, and in most cases loaded with explosives. Its primary aim is to enable efficient excavation down to the target floor level. Subdrill is often described as being expensive and that excessive subdrill should be avoided, as it can result in damage to the subsequent floor, lead to difficult drilling conditions and higher vibration levels. As a result, many operations aim to apply the bare minimum amount of subdrill in order to excavate to the target floor. At a large open cut copper operation, challenging geological structure resulted in slabby and blocky fragmentation in the stemming region, resulting in poor crusher throughput due to bridging. To overcome the poor fragmentation in the top of the bench, longer than conventional subdrill was used to precondition the top third of the bench. The technique significantly improved the run of mine fragmentation and resulted in feed to the in-pit crushers that is more consistent, which produced less crusher downtime due to bridging. A new method of quantifying the energy in a blast has been created. Termed the linear powder factor, or energy factor, the calculation considers the energy contributed by the subdrill of the upper bench and its impact on the energy in the lower bench. The technique enables blast designs to be optimised to deliver finer fragmentation and more consistent blast outcomes. To support the layer of preconditioned rock at the top of the bench, an innovative new device was developed. The device is inserted into the drill collar immediately after drilling and remains in position throughout the subsequent steps of hole depth measurement, priming, loading and removed prior to stemming. The device not only supports the broken rock at the top of the bench, but also minimises the amount of drill cuttings that fall back into the hole. Furthermore, the device helps protect the hole from damage by external factors such as weather events, drill tracks, vehicle tyres and movement around the collar during measurement and loading of the blast hole.