Search Documents

By A. Spathis, I. Yacob, A. Labriola, G. Smith

Wall control is a significant issue for many mines. Improvements to the design process for blasts adjacent to temporary or final walls will require better measurement tools and predictive models. Orica Explosives has developed capability in both these areas and uses them to guide better wall control blasting practices. Vibration and gas pressure were monitored behind a series of production blasts and single hole blasts at the Freeport Grasberg Operations Opencut Mine. The blasts used ANFO in both 3 11 mm and 35 1 mm blastholes in a blast design which reduced the charge weight by between 30 to 50% in the final row of the production blasts. Single hole blast data were obtained by delaying the last hole in the production blast. Vibration levels were within the range often associated with vibration induced damage: 178 to 1080 mm/s at distances between 14-75 metres from the blast.

Jan 1, 2001

By V Krishna Mohan, J Edmund Hay

This paper discusses the results of the gap sensitivity measurements made on water-gel explosives, sensitized by monomethylamine nitrate (MMAN) and flake aluminium, and one emulsion explosive. This study specifically deals with the effect of the mode of initiation, end or center, on the measured L50 values with air gap and coal dust gap for the above explosives. Similar measurements have also been carried out on a nitroglycerine (NG) - based explosive. The results show that the mode of initiation plays an important role in determining the air-gap sensitivity of these explosives. However, in tests carried out with the coal dust gap, the L50 ( grams of coal dust ) values for these explosives are close in both the types of initiation. The results indicate that the sensitivities of these explosives may be ordered in the following manner: NG-explosive>> Aluminized explosive ~ MMAN-explosive > Emulsion explosive

Jan 1, 1982

By Adrian Moore, Alan Richards

A real-time system for prediction of the effect of meteorological conditions on airblast overpressure levels has been established in the Hunter Valley Coalfield in Australia. Real-time meteorological data from continuously operating sounding equipment and a predictive meteorological model is input to an atmospheric refraction model that enables the effect of meteorology on airblast overpressure levels in the area surrounding the blast site to be evaluated. Graphical outputs from the model, which are superimposed over a scaled airphoto of the mine and surrounding area, show the extent that airblast levels will be increased. When combined with inputs that quantify the effect of blasting specifications, the airblast levels that will result in the surrounding area from the combined effect of blasting specifications is determined. The model permits those responsible for blasting to make more accurate decisions on suitable times that blasting may take place to conform with applicable airblast limits.

Jan 1, 2009

By Ryan Brogden

On the 5 September 2014 a road train (tractor-trailer) with two trailers carrying ammonium nitrate was involved in a single vehicle accident on the Mitchell Highway, 30 kilometers (18 miles) south of Charleville in Central Queensland, Australia. The ammonium nitrate was being transported to a mine site for use as a blasting explosive. The truck came to rest in the creek bed adjacent to a road bridge and caught fire. The vehicle burnt for over one hour before the load of ammonium nitrate exploded. Miraculously there were no fatalities; however eight people nearby sustained injuries, some seriously. The road and rail bridge over Angellala Creek were destroyed and vehicles in the nearby vicinity were seriously damaged. The truck carrying the ammonium nitrate was completely destroyed with over 2500 pieces of debris scattered up to one thousand yards (one kilometer) from the blast site.

Jan 1, 2018

By J Silva Castro, W C. Wedding, B T. Lusk, J Calnan, E G. Morris

The emergence of electronic detonators for use in production mine blasting has enabled mining professionals to rethink the traditional blast design methodologies that pertain to timing. In many ways, electronic detonators can allow great advances in productivity, cost effectiveness, fragmentation, and safety. This paper reports on an independent study quantifying the accuracy of two electronic and two non-electric systems in which 674 detonators were tested. This research aimed to determine the accuracy of commercially available electronic detonators as compared to non-electric shocktube systems. Each system was tested over the viable ranges of delays available. Statistical models were then applied to quantify the scatter present in each system. Suggestions for the use of electronic detonators are made from the findings of this work. This work was made possible through funding from the United States Department of the Interior Office of Surface Mining Reclamation and Enforcement.

Jan 1, 2012

By Edward J. Jr Walter

This paper discusses the use of slant hole drilling and water matting as an effective method of reducing costs in shaft sinking operations through a general review of cost priorities for the contractor.

Jan 1, 1976

By P. N. Worsey, M. Schmidt

Many advanced military systems and civilian power generation concepts postulate the availability of compact sources of electrical power capable of delivering gigawatts over microsecond time scales. For example, such a compact power source is essential for future practical pulsed high-powered microwave sources. An explosive-driven flux-compression power generator (EDPG) could fill this requirement. A basic strength of this concept capitalizes on the inherent high energy density storage capacity of modern chemical explosives. It relies on the physics of magnetic flux compression to convert that stored chemical energy into very large amounts of electrical power over short time scales. The generator also has the additional advantage of employing the same types of explosives that are already routinely used in conventional munitions. However, the self-destructive nature of this type of power generator places serious limitations on power pulse-lengths and ranges of applications. This paper describes how a multi-disciplinary team led by researchers from the University of Missouri-Rolla (UMR), Texas Tech University (TTU), and Texas A&M University was awarded a grant by the U.S. Air Force Office of Scientific Research to perform basic research to resolve several fundamental EDPG problem areas. Described are the utilization of UMR’s extensive explosives research expertise and facilities to investigate questions of energy conversion efficiency and the mechanics of energy production. Also, UMR explosives researchers will provide inputs to improved dynamic computer models of the complex, intertwined physics and chemistry operative in these devices. In addition to explosives expertise, UMR provides facilities for basic explosives material research, as well as the storage, machining, and formulation of explosives. UMR researchers are also using test facilities and data collection equipment at the Rock Mechanics and Explosives Research Center and at the UMR Experimental Mine to perform “proof of principle” and subscale tests of explosive-driven flux-compression power generator components. An integral part of the paper is a description of the development of an extreme intensity flash system by UMR and TTU to allow for the high-speed photography of EDPGs in operation. This multi disciplinary research program offers major advances regarding the size, weight, and electrical characteristics of compact EPDGs. Such breakthroughs could dramatically accelerate the practical realization of systems currently under study. Also, these power sources may have far reaching relevance to other Department of Defense and certain commercial compact power applications.

Jan 1, 2000

By Clara Godoy, Álvaro Dapía, Paulo Couceiro, Håkan Schunnesson, Juan Navarro

This paper applies geostatistical tools in Measure While Drilling (MWD)data to estimate the probability distribution of values in all the points of the studied domain in order to assess the continuity of rock classes between boreholes. The analyses carried out by Ghosh et al.(2018) and Navarro et al.(2019) have been used as starting point of this work to classify the geotechnical rock condition in four classes: solid rock, fractured rock, cave-in rock and cavity. From it, an application for the geotechnical rock condition of ore bodies have been developed, aiming at characterizing the rock before the charging the holes to minimize unexpected rock conditions and to address issues associated with charging and blasting operations. Such problems are closely related with non-optimal rock fragmentation after blasting. The procedure has been applied in the geotechnical block model results obtained from Navarro et al.(2019)’s work in the Luossavaara-Kiirunavaara AB’s (LKAB) Malmberget underground iron ore mine, Sweden. Navarro et al.(2019)’s model was developed based on102 fan-holes from five ore bodies and extrapolated to the full-scale in20 drifts with 5600 fan-holes from two orebodies. A multi-step transformation of the MWD parameters was carried out in order to minimize external influences other than the rock mass. The study shows the calculations of the variogram and kriging estimation in the 3D domain for six ring-blasts, from one of the ore bodies studied in Navarro et al. (2019)’s work to assess the continuity of the rock classes along the six ring-blasts in a 3D mapping model. For that, intermediate rings between the measured ones from the MWD have been estimated. The probability distribution of values in the entire domain of rings with measured samples has been plotted together with the rock classes identified by the blasthole paths. The results show high accuracy in the matching between the kriging and the values given by the MWD data, allowing to visualize smooth trends of different rock classes along the ring. The representation of the 3D mapping model for the six ring-blast shows clear fractured and cave-in zones developed along the drift that correspond to zones with geotechnical problems found, as from internal reports.

By Daniel Johansson, Markus Danielsson, Håkan Schunnesson

In sublevel caving, blasted material flows gravitationally into the drawpoint from above in a periodical manner. This type of flow behavior entails muck pile conditions that are variable along the course of extraction. The effect of this variability on the LHD (Load-Haul-Dump) operation in terms of loading efficiency and ability to undermine the blasted ring is not fully understood as of today. This paper presents results from a field test in LKABs Malmberget mine in Sweden, where the influence of fragmentation on the loading operation has been studied in detail. Drawpoint filming was conducted for extraction of two rings equivalent of roughly 10000 metric tons (~9842 long tons) of material each. The analysis includes fragmentation measurements, muck pile classification, and general estimations in terms of loadability. Further, an evaluation of LHD machines from two different manufacturers was conducted to identify and highlight differences. The results show that fragmentation, muck pile compactness, and flow characteristics are all interdependent. Flow disturbances and the subsequent loading of compacted fine material in the back of the ring have been identified as the main reason for occurring problems and prolonged digging times. However, the ability to sufficiently undermine the blasted ring has been identified to primarily depend on digging depth which is only observed to be high during flow disturbances. An absence of flow disturbances seem to promote high loading efficiency but simultaneously limit the maximum digging depth. A mid-range particle size distribution with a low amount of fines has proven beneficial for overall loading efficiency. The various LHDs employed showed significant variations in terms of ability to handle difficult loading situations (e.g. compactness, boulders, etc.).

Jan 1, 2018

By Dean E. Albon

The author gives a brief resume of his observations of drilling and blasting supervision in surface coal mines during the past thirty years and recommendations for upgrading this supervision to the category of a professional.

Jan 1, 1979

By P D. Katsabanis

Explosives malfunction due to shock waves is a serious concern for successful blasting results. Malfunction includes sympathetic detonation and desensitization of explosive charges as well as the modification of firing times of conventional pyrotechnic detonators.

Jan 1, 1995

By J MacPhail, H Gardner

This paper discusses reasons why users of rotary air blast hole bits encounter premature bit failure due to bearing failure. It also discusses a lubrication system designed for rotary rock bits to combat bearing failure.

Jan 1, 1996

By Geff Gordon, Dale Nies

Small diameter borehole blasting can be very efficient and cost effective. As residential development continues to expand, many areas are now requiring blasting for site preparation and upgrading old utility systems or constructing new ones.

Jan 1, 1990

By Jean A. McIntyre

The Office of Surface Mining (OSM) has twice proposed rules for a blaster training and certification program to implement Sections 515(b)(15)(D) and 719 of the Surface Mining Control and Reclamation Act of 1977.

Jan 1, 1980

By Rodney C. Espley-Jones, John C. B Wilson

South Africa is well known for its shaft sinking exploits, and many of the world's biggest and deepest shafts are to be found there. Blasting practice differs in a number of respects from that followed elsewhere.

Jan 1, 1979

By Soseol Kim

A high-performance Emulsion-based booster explosives has been developed that can be used as a booster for bulk explosives. Currently, Pentolite booster, which is mainly used as a booster for bulk explosives, has a high risk of accidents due to the sensitivity of its raw materials PETN and TNT, and has a low melting point, making it impossible to use it in high-temperature ground. The Emulsion-based booster was developed to maximize the Velocity of Detonation (VOD) while elimination the shortcomings of the Pentolite booster. The VOD of the Emulsion-based booster is about 6,500m/s, so it can maximize the performance of the bulk explosive. In addition, it can be used in high-temperature ground and does not cause accidental detonation due to the external environment. In this article, the performance of the Emulsion booster was verifies through comparative test blasting of the developed Emulsion-based booster and Pentolite booster.

Feb 6, 2023

By Clive-Workman Davies, K K. Kabongo, Mensah Frimpong

Given the capital intensity of the dragline operation coupled with rising cost of explosives, the onus is on mine operators to make maximum use of explosives in blasting to assist dragline diggability. At a surface coal mine in South Africa large boulders necessitating secondary breakage and in some cases completely unfragmented sections of a blast resulting in low dragline diggability were encountered in the interburden blast. Twelve blasts were therefore closely monitored and dragline productivity evaluated. The ultimate aim was to improve the overall blasting performance and hence increase dragline productivity. Three areas were in focus; fragmentation assessment, dragline productivity assessment and cost analysis. The studies indicated unsatisfactory explosive and initiation performance, problematic blast design and questionable operators performance. It is established that dragline cost account for 60% of the total mining cost whereas the drilling and blasting cost account for the remaining 40% and that improvement in dragline productivity results in automatic cost saving.

Jan 1, 1996

By M Siefert, P Moser, T Oberndorfer

"The EC-project ""Blasting Control"" with partners from France, Austria, Italy and Greece dealt with the development of a diagnosis system, which enables blasting experts to investigate in detail on probable reasons of poor blasting results in underground drifting. The system incorporates monitoring of geometric, explosive, vibration and granulometry data. All data are compiled in a database and are provided for direct retrievement by demand of the experts in a graphical environment. This paper focuses on the advantages of such graphical system for both research tasks and applications in real testing situations. It describes the procedure of monitoring and presents a selection of graphical outputs generated during data processing immediately after blasting. Benefits of detailed monitoring in respect of detecting sources of errors are explicated by a actual example of a test series in a mine. The paper will conclude with an outlook onto the scientificresearch work which is planned to be based on the results of hitherto investigations."

Jan 1, 1996

By Claude Cunningham

Simple bulk energy rating of explosives obscures the realities of how these deliver their energy, and diverts attention from the key question of controlling blasting results. Explosive performance is directly related to the pressure pulse impacting on the blasthole wall. This is helpfully visualised by comparing the adiabatic expansion plots for explosives of interest on the right scales and axes. The simple comparison of a pure emulsion with pure ANFO illustrates the practical significance of the intrinsic behaviour of these opposed formulations, showing that the emulsion can be expected to work more by softening rock, while ANFO will tend more to crack it. The explanation for these differences lies in the high shock, low sustained pressure of the former relative to the latter. The technique is readily applied, if a good detonation code is available and able to swap data into a spreadsheet. Any differences between codes will emerge most strongly in comparing the gamma plots.

Jan 1, 2002

By John C. Brulia

PowerAN is a tradename of Atlas Powder Company for a new line of explosive products comprising blends of emulsion and ANFO in a variety of bulk and packaged grades. The bulk PowerAN grades are either augered or pumped depending upon emulsion content. Augered PowerAN blends contain up to 60% emulsion. Pumped PowerAN grades have an emulsion content of 75% or higher. The blending of PowerAN is usually accomplished at the borehole to satisfy specific borehole conditions. Packaged PowerAN grades are produced in several types of mix plants in diameters of 4" and greater. PowerAN 300 (30% emulsion) and PowerAN 500 (50% emulsion) are the two most popular grades and their chief application is as an economical, high energy replacement for ANFO HD in wet holes. PowerAN combines the cost effectiveness of ANFO with the high performance of emulsions, permitting the blasting engineer to strike an optimum balance between drill pattern expansion and increased productivity according to need.

Jan 1, 1985