Search Documents

By Detnet Solutions

1. “Daisy-Chain” concept The term “daisy-chain” stems from the fact that when the HotShot? detonators are connected there is a chain or electrical path for electrical current to flow from detonator A to detonator B, detonator B to detonator C etc until the path is terminated by an electrical means. The “daisy-chain” concept has long been used in electronic detonator systems, historically used in Expert Explosives’ ExEx 1000 5/6 wire system and currently in use in African Explosives Limited (AEL’s) Electrodet? electronic detonator system and has been adopted as the basis upon which the “auto-programmability” of the HotShot? electronic detonator system functions. HotShot? Detonators are connected to each other in a string, completing a “daisy chain”, and during the auto-detection mode of the control equipment, it is possible for the equipment to determine the order of hookup of the detonators as well as map the entire blast layout. The auxiliary components (Row Controllers & Branch Controllers) assist the control equipment in mapping the entire blast by indicating different points on the blast, i.e. The inflection point of a row of blast holes on a closed chevron timing pattern, the beginning of row of blast holes on open chevron timing pattern and extra blast holes or extra blast rows.

Jan 1, 2004

By Robert Jacob Cefalo, Rio Tinto Kennecott

At the end of 2016, the Mine started a new ore phase in the section of the pit located on the East Wall. The East Wall geological structures required controlled blasting for peak particle velocity (PPV) frequency vibrations to protect the wall. Frequency controlled blasting using linear seed wave superposition modeling was required and implemented to reduce the far-field affects to the wall. This paper covers the work done by the drill and blast engineering group, controls used to protect the mine infrastructure, and the continuation of work-to-date of frequency controlled blasting for wall stability. The narrow width of the layback required the combination of hole sizes to blast large diameter production patterns with smaller diameter trim patterns in the same blast. A single blast had to use different burden & spacing and hole diameters and required the use of different timings throughout the pattern. Electronic detonators were required to limit blast vibrations and accommodate the specific timings needed to reduce low frequencies. The geotechnical group with the help of geotechnical radars worked with the drill and blast group on creating a tracking and reporting of blast performance. The radar readings informed the drill and blast engineers of the performance of the blast as it related to the long term performance of the highwall

Jan 1, 2019

By Marcia Harris, Richard Mainiero, Michael Sapko

Since 1988, there have been 17 documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through ground strata into occupied enclosed spaces as a result of proximate trench blasting or surface mine blasting. These incidents resulted in 39 suspected or medically verified carbon monoxide poisonings and one fatality. To better understand the factors contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out studies in a 12-foot diameter sphere to identify key factors that may enhance the levels of CO associated with the detonation of several commercial trenching explosives. The gaseous detonation products from emulsions, a watergel, and ANFO blasting agents as well as gelatin dynamite, TNT, and Pentolite boosters were measured in an argon atmosphere and compared with those for the same explosives detonated in air. Test variables included explosive formulation, wrapper, aluminum addition, oxygen balance, and density. Major contributing factors to CO production, under these laboratory test conditions, are presented. The main finding is the high CO production associated with the lack of afterburning in an oxygen poor atmosphere. Fumes measurements are compared with the manufacturer’s reported IME fume class and with the Federal Relative Toxicity Standard 30 CFR Part 15 in order to gain an understanding of the relative toxicity of some explosives used in trench blasting.

Jan 1, 2003

By Paul Downing

A typical day for a blasting company includes what seems to be an infinite list of tasks dealing with numbers. Whether determining the exact amount of explosives material in inventory, the number of holes in the shot, the exact distance from the blast site to the nearest exposure, or the capacity of bulk hoppers, the accuracy of numbers is key to ensuring the safety of the public, property and personnel.

Jan 1, 2008

By SMF Hossaini

With the aim of a clearer understanding of the applicability of existing empirical equations for blast induced ground vibration, an investigation has been conducted on three mostly applied forms of such equations. The effect of explosive type on the applicability of these equations has been assessed by analysing 44 sets of data produced by using two types of explosives, namely ANFO and slurry explosive, in an open pit coal mine. The analysis of the data has revealed that the type of explosive affects the applicability of the criteria of the three equations. All three criteria have better correlation with the data of shots in which ANFO was used than the shots with slurry explosive. However, the applicability of one of the criteria is reduced, by far, only by replacing ANFO with slurry explosive for the same ground conditions. It was also found that one of the parameters of these criteria (i.e. “k”) is significantly sensitive to the type of explosive in all the three equations. The degree of influence to the values of “k” obtained by the variation of explosive from ANFO to slurry explosive in the three equations is 76.3%, 811% and 39%. This implies that “k” is not only dependant on ground conditions, as stated in most previous publications, but is also strongly a function of the type of explosive.

Jan 1, 2004

By Ray Jambakhsh, Gabrielle Bourget

In the summer of 1998, Ontario Hydro awarded a contract to demolish an obsolete and inefficient chimney by blasting. The Ontario Hydro Thunder Bay Thermal Generating Station (T.G.S.), is a fully operational hydro thermal generating station located in Thunder Bay, Ontario, Canada. The Chimney was a 356 ft (108 m) high freestanding structure constructed of reinforced concrete with a brick liner. Falling the chimney required careful planning due to the highly sensitive structures and equipment which surrounded it. Damage either sustained to the existing systems through ground vibrations or direct contact would have resulted in expensive power outage and/or lost production. The role of Explotech Engineering Ltd. on this project was to provide and evaluation of the proposed demolition procedure, defme the predicted and maximum seismic vibrations at sensitive structures including underground services, conduct pre-blast / post-blast inspections and recommend various safety precautions. The general contractor for the project, LeBrun Northern Contracting Ltd., of Thunder Bay, Ontario was responsible for all site preparations and post-blast clean up. All demolition blasting calculations and operations were conducted by Dykon demolition experts from Tulsa, Oklahoma. On September 13, 1999, the chimney was successfully demolished. Extensive analysis of the vibration records and visual post-blast inspections of the surrounding structures concluded that the demolition event induced no damage to any of the Ontario Hydro facilities.

Jan 1, 2000

By Peter Moser, Frank Chiapetta, Sacha Diaj, Florian Bauer

Good toe breakage and a flat working bench after blasting are important parameters to achieve a high productivity during material loading and reduce the necessity for secondary blasting. Good toe breakage requires a proper burden – side spacing design and a suitable sub-drilling. With unfavourable jointed rock mass conditions the use of horizontal bottom holes still can be found as common work practice even that this is associated to high risks.

Jan 1, 2009

By John Babcock, Gregory Poole, Ron Hudson

In January 2007, Fultondale Alabama opened a new elementary school. Site work at the old school location included blasting activities and the old school building was scheduled for demolition. With help from Apache Construction, blasting was scheduled to be performed in close proximity to the old school building prior to the demolition. Arrangements were made to perform extensive monitoring on the old school building during the blasting activities. The monitoring plan for the project included: • Pre and post blast inspections were performed on the structure; • Conventional crack monitors were installed at 22 locations throughout the structure; • Digital displacement monitors were installed at 6 locations on the structure; and • Seismographs were used to monitor structure vibration at 6 locations and ground vibrations at 9 locations. Blasting activities were allowed to produce vibration levels well above the safe levels established by the U.S. Bureau of Mines (USBM). Vibration levels up to 7.44 in/sec were recorded with no damage noted. Permanent deformation was recorded on vibration levels of 9.68 and above. Not only did this project reinforce previous studies which indicate that concrete block walls can withstand vibration levels well above 2.0 in/sec, this study was also a good example of employing new technology to help determine if/when damage occurs on a specific structure.

Jan 1, 2009

By Vic Sterner

As cities and towns continue to grow, the need to install sewer, water, gas and other utilities becomes a necessity and the blasting of trenches for these service lines probably constitutes one of the most important forms of blasting in built-up areas. There f o re, understanding how explosives can be safely used in the most efficient manner is of prime importance. The need for protection against flyrock must be emphasized. The first consideration is that all explosive c h a rges should be located well down in the blastholes. The golden rule is to ensure that the depth of top stemming is never less than the burden on the hole. In the case of shallow holes, the minimum depth of stemming should not be less than 18 times the charge diameter, if airblast and flyrock are to be controlled. If there is a doubt, then additional cover and/or blasting mats should be used. Putting too much burden on blastholes is another possible cause of flyrock and raising ground vibration levels. Overburdening of explosive charges will also result in the blastholes not breaking to grade. This in t u rn re q u i res additional drilling of shallow holes down in the trench to achieve grade, thus further increasing the h a z a rd of flyrock .

Jan 1, 2004

By Randall M. Wheeler

It is important to be able to quantify the effects of blast delay designs on vibration characteristics. White was the first company to develop commercially available software, called Alpha-Blast, for this purpose. The program can indicate relative amplitude and frequency results to be expected from the use of particular delay intervals. If enhanced vibration effects from delays are a problem, a technique to evaluate this situation will be invaluable.

Jan 1, 1994

By Thierry Bernard, Guy Gagnon

Blasting at very close proximity to urban areas is typically a situation where both local communities and mining stakeholders get nervous. The context becomes logically even more tensed when the blasting operations have to be performed above an old underground mine. When mitigating subsidence risks requires firing the largest possible shots, the nuisance control (flyrock, vibration, and noise) required by local and national regulations, contrarily urge for being more conservative.

Jan 1, 2014

By Ewan Selers, Gary Cavanough

Drilling automation technology is well advanced and automated drill rigs are in use at a number of operating mines. This is not the case for the other drill and blast processes due to significant technical challenges to overcome. These challenges, with regard to the current “on bench” practices, include placing the initiators, loading the explosive and connecting up the initiation system. Although difficult, these challenges will be solved with engineering advances.

Jan 1, 2016

By Steve Colbum

LTl’s MapStar LPS (laser positioning system) utilize both tripod mounted and hand held reflectorless distance meters. These are eye safe, easy-to-use, and specifically designed to endure the harsh environment characteristic to the mining, quarry and explosives industries. Survey data collected by the systems is digitally stored in a ruggedized data collector and then processed with a specialized, interactive software program, which can be run on any standard PC. Win Prof, the Windows-based analytical software package is used to reduce the data for generating bench face profiles, surfaces, volumes, estimating true burdens and mining ratio calculations. In addition, the software has many other built-in routines to calculate powder factors, toe shear, to map structural contacts and to predict the flyrock potential based on the Burden to Energy ratios. An extensive, built-in library of explosive’s data facilitates these calculations. It will also conform automatically to user-specified minimum and/or maximum burden in relation to the explosive energy, hole diameter and bench geometry - for both vertical and inclined holes. Numerical data can be represented in 2D or 3D to emphasize the hole-burden-face relationships.In this workshop, the MapStar LPS instruments and Win Prof analytical software will be thoroughly demonstrated. Demonstrations include equipment configuration, typical field setups and several effective survey procedures, including processing of some sample data.

Jan 1, 2000

By W. J. Birch, R. Farnfield, S. Hosein, C. Johnson

Modern smart phones include accelerometers based on MEMS (Micro Electro Mechanical System) technology giving the possibility to measure both acceleration and orientation. The widespread use of such phones has driven technological development to such a degree that it is now possible to obtain a triaxial accelerometer unit, that also include signal conditioning and analogue to digital conversion, in a package smaller than 1 cm2 (1/2 sq.in) for a relatively low cost.

Feb 6, 2023

By Ethan Steward, Robert Eades, Kyle Perry

Shock tubes, either gas or explosively driven, are often used for physical modeling of free field explosions or arena testing. The use of shock tubes often requires less setup time of subjects and smaller driving forces to create pressure versus time waveforms similar to that of arena testing. However, the effects of the shock tube cross sectional geometry on waveform properties is uncertain while free field explosion wave propagation and estimation is well studied.

Jan 1, 2018

By Thierry Bernard

Since the signature hole method principle has been described in the 80's, there has always been a lot of controversy about it. The theory is easy to understand but when it comes to apply it for predicting vibration level, optimizing timing to reduce PPV or shifting frequencies, it’s not always working as expected. Simulations show waveforms that don't make any sense or predictions that are far away from actual results.

Jan 1, 2012

By D P. Proudfoot, S G. Keith, D P. Onagi

A number of aspects of the Canadian concept for nuclear fuel waste disposal are being assessed by Atomic Energy of Canada Limited (AECL) in a series of experiments at its Underground Research Laboratory (URL) near Lac du Bonnet, Manitoba, Canada. One of the major objectives of the work being carried out at the URL is to develop and evaluate the methods and technology to ensure safe, permanent disposal of Canada's nuclear fuel waste.

Jan 1, 1996

By ISEE

Micrometer Crack Response to Vibration and Weather, by Prof. Charles H. Dowding of Northwestern University, adds to Prof. Dowding’s already important contributions to the industry with his “Construction Vibrations” books. This new book reports and interprets important data on crack response that are essential for differentiating the unseen effect of weather on structural cracking from the usually much smaller effect of vibration. In addition, the book contains detailed descriptions of data collection methodology.

Jan 1, 2010

By David Davison

Metafex®* is an inert material that is more energetic than explosives when activated. Because Metafex is inert until activated (a moment before use), it can profoundly change the logistics of systems and processes that require energetic materials. We have obtained positive test results for a Metafex configuration (called a flat pack) that operates at the practical voltage of ~20 kV. We describe the outcome of the testing and potential uses of the material.

Jan 1, 2006

By Tristan Worsey, Nathan Rouse

The Florida legislature allocated funding for the Florida State Fire Marshal (FSFM) to review the applicability of the United States Bureau of Mines (USBM) Report of Investigations (RI) 8507 blast vibration limits with respect to Florida and its soils. The study also discusses whether the current blasting vibration limits set by statute are still appropriate, including a review of measured vibration amplitudes and frequencies, structure responses, and theoretical analyses of material strength and strains

Jan 1, 2019