Search Documents

By Tom Treleaven, Andrew Williams

The town of Greenwich, CT, an exclusive suburb of New York City awarded several contracts for the installation of sanitary sewer in the North Mianus section of town. The Valley Road section was the most challenging from a rock excavation standpoint. The cut was up to 14 ft (4.25m), with adjacent utilities [20 in. (500mm) water, 6 in. (150mm) water and 8 in. (200mm) gas] located to within 5 ft. (1.5m) of the proposed sewer trench. Rock types varied but were ultra metamorphic in nature, ranging from quartzites, granite gneiss and various types of migmatities.

Jan 1, 2004

By Hae-Moon Choi, Sang-Don Lee, Chang-Ha Ryu

The purpose of the study presented in this article is to establish a standard blast pattern to yield optimum blasting performance along with an attempt to reduce a difference between design and construction. A series of test blasts were carried out at two tunneling sites of Central Inland Highway crossing in Korea. Long-hole blasting was tested in rock mass whose RMR value is over 60.The blasting results were evaluated by measuring degree of fragmentation, advance rate,muckpile distribution, overbreak, etc. Based on the results of test blast, several patterns were proposed for a two-lane highway tunnel.

Jan 1, 2006

By Professor of Civil and Environmental Engineering Northwestern University, Mike Wladron, Gordon Revey

A unique judicial opportunity allowed measurement of the response of three cracks in residential structure to blasting for underground aggregate mining. Instrumented cracks were located in the interior basement CMU mortar and upstairs dry wall as well as exterior brickwork. The dynamic environment was unusual. Even though the blasting occurred some 490 m (1600 ft) away, excitation frequencies were unusually high and there were no apparent surface waves. In addition there was no air overpressure wave to produce secondary crack response. As is typical, long term environmental effects produced greater crack response than did the blast induced ground motions.

Jan 1, 2007

By Jorge Cardenas, David Martinez

Blasting-induced vibrations can be predicted with high precision, allowing for the optimization of sequence design, delay timing, and charge configurations to minimize their indirect impact on rock masses. This optimization leads to a reduction in peak particle velocity (PPV) and dominant frequency at monitoring points. However, a crucial aspect of slope safety is estimating the degree to which vibrations influence stability through numerical modeling of the dynamic response. Slope stability is closely linked to rock mass strength, the predominant failure mechanism based on discontinuity orientation relative to the slope face, and the pre-existing stability conditions before dynamic alterations occur. Blocks, wedges, and planar failures tend to slide under lower vibration levels and are more susceptible to resonance, particularly in fractured and low-strength rock masses. To evaluate the interaction between rock mass and vibrations, photogrammetry and artificial intelligence were employed to identify discontinuity families at vibration monitoring sites. This data facilitated the development of artificial discontinuity networks (DFN), which replicated a discontinuous medium within a numerical finite element model. The input signal was recorded at the slope base using triaxial geophones and incorporated into a discontinuous numerical model. The output signal was estimated through finite element analysis and subsequently compared with geophone measurements taken at the same location. Based on real-world output signals, damping parameters and the model’s natural frequency were adjusted to align both frequency spectra. Using the calibrated parameters, vibration records from various blasting projects at different distances were applied as input signals until slope failure was induced, thereby defining maximum allowable vibration limits in terms of PPV and frequency at the monitoring point. This approach provided a framework for optimizing sequence designs, charge configurations, and delay timings to enhance slope safety and prevent failure due to blasting-induced vibrations.

Jan 26, 2026

By Julio Cesar Barbosa de Freitas, Rafael Gonçalves Araujo, Túlio Soares, Jair Koppe, Augusto Ferraz Ribeiro, Pedro Barreto Garcia

This study thesis was motivated by the fact that it is of fundamental importance for open pit mining that the slopes initially have a geometry in accordance with what is proposed in the mining planning. This occurs because an inconsistency in this design can impact the operational safety and economic solutions of the mining project. These consequences can be explained by the fact that rock blasting close to mining limits requires specific study due to the attention required. Because, when this operation is not carried out properly, the mining plan in the mine may not be respected and may create risks to the operation due to the presence of unstable blocks on the slopes (Mackenzie). In this sense, Mackenzie (2004) cites pre-split, trim blasting and buffer as commonly used explosive blasting techniques that aim to limit damage beyond the projected wall. Therefore, Enaex Brazil realized the need to better understand the pre-split method. To do this, it is necessary to understand how the energy released during detonation is perpetuated in the rock mass when this technique is used and when it is absent. Thus, this analysis is based on a seismic study that allows the creation of vibration attenuation laws and an elementary wave damage model, which allows the local characterization of the rock. With this model it is possible to relate the peak levels of vibration during blasting and the extent of damage, but a critical level of vibration (PPVc) and its relationship with the Uniaxial Comprehension Resistance (UCS) are also defined for the start of fracturing and its level (McKenzie et al, 1995). And, mainly, this work aims to address a way to measure the pre-split filter potential by comparing the attenuation law with and without pre-split, ultimately knowing whether this finishing blasting is being effective, to understand the pre-split filter capacity.

Jan 21, 2025

By G. Cavanough, A. Torrance

Emulsions have been developed for over forty years to become the most common water-resistant explosives used in the mining industry. An emulsion is a common commodity, with many examples in our day to day lives of one immiscible liquid dispersed in another. They have varying degrees of stability from a few seconds to years. What makes their application in explosives unique is twofold. They contain a high concentration of salts in the dispersed phase and also have a far larger volume of dispersed phase than continuous phase. The continuous phase contains at least 75% by weight of an oxidizer such as ammonium nitrate dissolved in water. The crystallization point of these solutions is often >60oC which means that the formation of the emulsion has to occur at an elevated temperature. Once the emulsion is cooled, its structure helps to prevent the formation of crystals in an otherwise unstable system. At room temperature there is a considerable potential for the small oxidizer droplets to crystallize which is countered by the strength of the oil layer and also the size of the emulsion droplet. If the emulsion droplet is too large then crystals can form which may lead to rapid deterioration of the emulsion and overall crystallization, accompanied by a temperature rise as the heat of crystallization is released from the emulsion. The size of the emulsion droplet is critical in preventing crystal growth and subsequent droplet coalescence and emulsion break down. One method of examining emulsions and understanding their structure is to use optical microscopy to measure droplet size and also emulsion deterioration from shearing, temperature cycling and when contaminants are introduced, such as detergents, different oil types, coating agents and dust particles. This paper reports on advanced techniques to quickly assess emulsion quality and stability

Jan 1, 2024

By Peter Moser, A. Gaich, E. Grasedieck Zechmann

In The SMX Blast Controller is a novel tool for precisely controlling the geometry of a blast based on the technology of 3D imaging. It enables to derive precise information about the geometry of the face of a bench in a quarry from a pair of stereoscopic images taken from the bottom level of a bench with a calibrated standard digital camera. Apart from staking out the blast position with delimiters that mark the area to blast and taking then two images (freely), no further actions are required which allows performing the data acquisition without requiring any surveying skills. The 3D image generation and blast planning does not require special computer. It is estimated, that every blast foremen is able to work with the system after a one-day training as the system includes a high grade on automatism. The software package allows the blast foreman to design and stake out a blast, based on provided geometric values, such as burden, side spacing, hole inclination, sub-drilling, row number & distance and drilling pattern. The software connects these values with the 3D information acquired by the digital images. All the drill & blast information can be used also for blast documentation. The SMX Blast Controller overcomes also the problem of doing the back transfer from maps derived by surveying into nature as the resulting 3D image and all the information associated to it (hole position, etc.) can be correlated with the nature by visual comparison and the help of a single reference line, defined by two points. The system is designed to be used also in small to medium quarries. It can help, that the control of the geometry of the bench face and the precise design of the charge of the blast on a borehole per borehole basis will become an accepted daily routine.

Jan 1, 2006

By Jonathan Zimmerling, Rob Alkins

The model of waves emanating from a blast hole proposed by Heelan, and further developed by Blair and Minchinton, provides an approximation of particle motion in an isotropic, continuous and homogenous medium caused by a cylindrical pressure source. Previous work in the literature shows that the shapes of the peak strain and peak particle velocity contours generated by this model are influenced by priming location. This paper presents the results of experimental investigations into the effects of priming position in an explosive column and the resulting shape of the surrounding stress and particle velocity fields. Fifteen emulsion charges were detonated in a limestone quarry, of which eight were bottom primed and seven top primed. The charges were fully confined, with no breakout to any surface. Particle velocity was monitored using tri-axial sensors coupled to the rock using cement, and pressure sensors were placed in water filled boreholes for fourteen of the experiments. Statistically significant differences in peak pressure for bottom and top primed shots were observed. Blair and Minchinton developed two pressure source functions, one of which is scaled using the charge weight scaling law. New models of the explosive pressure source are developed and compared to those found in the literature. These models are directly calibrated by predicting the peak velocities achieved at the known locations of the velocity sensors, then minimizing the residual sum of squares between the predicted and observed peak vibration values. Due to the complexity of the model the residual sum of squares cannot be minimized using standard non-linear optimization techniques, so a stochastic, agent based global optimization method is employed. Models are then cross validated by comparing the relative predicted differences in stress between bottom and top priming position to the observed differences.

Jan 1, 2013

By Piyush Rai

Proper use of fi ring pattern vis-à-vis the blast requirements can provide optimal blast performance in terms of fragmentation. Further to this, each fi ring pattern has its own characteristic, for instance, although V-type and diagonal fi ring pattern provide same Se/Be ratio, the V-type fi ring pattern increases the opportunity for in-fl ight collision amongst broken rock fragments during their movement. Similarly straight V-type and skewed V type fi ring patterns (V1,V2 etc.) have their own characteristic strengths and weaknesses. In this light the present paper highlights the application of three different types of fi ring pattern on two different type of sandstone overburden benches of a large coalmine in India. The study reveals that Firing pattern infl uences the effective spacing to burden ratio at the time of detonation. By changing the fi ring pattern, effective burden (Be) changes and the ratio of effective spacing (Se) to effective burden (Be) during the fi ring is also subject to change in comparison to drilled spacing to burden ratio (S/B) Hence, the Se/Be ratio vis-à-vis fi ring pattern must be used to design the blast rounds. The results have been derived on the digital image analysis based fragment size characterization, excavator performance and evaluation of powder factor values on blasted muck piles. Skewed V- type fi ring yielded the best results in comparison to straight v-type and normally practiced diagonal fi ring pattern on the moderately strong sandstone benches, whereas, the existing diagonal fi ring pattern appears to be satisfactory on weak (weathered and gritty) sandstone benches. The presence of geological anomalies has also been investigated.

Jan 1, 2008

By H. S. Venkatesh R. Balachander, G. C. Naveen

During the construction of a 1020 MW underground hydroelectric project in Bhutan a huge rock fall took place in the Downstream Surge Chamber (DSC) during March 2016. The total quantity of rock in the fall area is estimated to be about 1,50,000m3 (2.6 billion cubic feet), out of which about 25,000m3 (0.44 billion cubic feet) of muck was removed. The removal of muck was stopped apprehending that the cavity formed due to the rock fall may get further aggravated leading to widening and destabilising the adjacent transformer hall cavern or it might day light as the top cover was about 190m (623 feet). As the fall has virtually blocked the 314m (1030 feet) long cavern and divided it into two different chambers (south and north), and that the muck cannot be disturbed, it was decided to erect concrete wall on either side of the fall up to the cavern roof and then later address the filling of the cavity with appropriate fill material. As the access to the DSC was there for the southern side it was decided to extend a cable tunnel which was terminated at a distance on the north side of the cavern by D&B so that once it gets punctured into the north wall of the DSC it can be used to access the fall from this front too. This is a unique situation where in every blast approaching the DSC, the parting between them is diminishing and hence the tunnel blast will be exerting axial load on the parting wall leading to dynamic transient loading conditions and buckling may take place on the northern wall of DSC. This paper describes the various drill blast combinations adopted for successful excavation of this tunnel.

Jan 1, 2019

By A Bagchi, Nabiullah, Jagdieh

"A number of coal mines in India are affected by fire. Most of coking coal reserves in the country are located in Jharia coalfield where more than 18 sq. km is in the grip of fire. Generally such fires are confined in areas near to our crops. About 37 million tonnes of coking coal are lost in recent yearsdue to fire and another 48 million tonnes are blocked in fire areas. Preventive measures adopted to control fires were only partially successful and the cost of such measures was exorbitant I Temperature of blast holes in fire area varies between 60 and 300° C or even more. Even after thorough quenching of holes with water, it become difficult to bring down the temperature below SO"" C. For blasting hot holes primary need is to select safe and suitable commercial explosives and detonating fuse and to measure hot hole temperatures. VWiOUs types of commercially available explosives including Nitro Glycerine bare, slurries, site mixed slurries (SMS), emulsion5 ,detonating fuses and detonators were tested to determine their thermal behaviour at elevated temperatures under field simulated conditions in the Copyright © 2000 International Society of Explosives Engineers 1993g - Studies on Safe Blasting Technique in Fire Area of Coal Mines laboratory and in hot blast holes in field . More than 50 round of blast were conducted in fire areas. NG base compositions and detonators were found unsafe at temperature above SO0 C andtherefore, they are not permitted to be used in hot holes. Slurries and emulsion are stable upto 1200 c. For blasting at temperature exceeding SO0 C a heat resistant gel/ solution was developed by the authors and is being used in number of fire areas."

Jan 1, 1993

By Geraldine Woods

I work for the State of Washington as an Explosives inspector. My paper will describe the mission of the Wa. State Dept. of Labor pertaining to explosives and the regulation of explosives in the State.Blasting safety is high on the public safety list and the regulation of explosive use and storage has been mandated through legislature. The Dept. considers pro-active partnering forexplosive safety preferable to after-the-fact citations for non-compliance.In some cases, the Dept. will issue civil citations with monetary penalties, meant to be a deterrant, of course, to blasters who choose not to comply with the explosive regulations of the State.The Dept. has also revoked and suspended blasting licenses. In some instances, the Dept. has allowed recipients of citations with monetary penalties to reduce the amount paid by attending technical training classes. The idea here, is to reduce the chance of reoccurence of unsafe blasting practices. The State of Washington partners with MSHA in the regulation of explosives use and storage in mines, pits and quarries in the Stateas well as working closely with law enforcement, State and local fire marshals, ATF,and is active in ISEE in part of it’s ongoing effort to promote explosive safety and establish communications in a nonadversarial way with explosives users. My paper will include some statistics on licensing in the State, pounds of explosives used, inspection numbers, numbers and types of complaints with information from the inspections resulting of these complaints. My paper will include examples of storage, both good and bad, examples and pictures of fly rock incidents, accidents, near-miss close calls, break-ins, thefts, and abandoned explosives. This paper may also include a brief summary of my opinion of explosive regulation and my job as a regulator, including examples of high and low points of the job, joys and frustrations.

Jan 1, 2002

By Terri Jordan, Gregory Hempen, Thomas Keevin

Water-borne blast pressures from confined blasts were recorded as part of a submerged blasting program in Florida for channel deepening. The blasting was confined within the rock floor by stemming. Shot patterns of stemmed borings were recorded, as were two open-water shots. One hole of one shot was not confined properly, which allowed comparison of confined and a poorly confined larger charge weights per delay. The pressure data were intended to gain information on typical pressure measures from the rock removal program relative to impacts on marine organisms. Water-borne pressures from actual confined, rock-removal shots validate the hypothesis of lessened impacts to aquatic and marine biota.

Jan 1, 2007

By H. S. Venkatesh, G. Gopinath, R. Balachander, G. C. Naveen

Punatsangchu Hydroelectric Project Authority is constructing 1020 MW underground hydroelectric project in Bhutan. The project envisages construction of concrete dam, Desilting Chamber, Head Race Tunnel, Power House Complex and Tail Race Tunnel. Tunneling is one of the major activity in any underground projects as they are driven for multiple activities. By and large the tunnels are a major part of connecting networks from surface to caverns/underground working sites. Many tunnels in hydropower project are part of water conducting systems and one such important tunnel is the Tail Race Tunnel in this project and had to be excavated in thinly foliated rockmass conditions by D&B method.

Feb 1, 2020

By Dale S. Preece, Ruilin Yang

"Air-decks are often employed for presplitting along the final highwall of a blast and are sometimes also included at the bottom or in the middle of explosive columns in the production portion of a blast. Shock wave physics is an important part of air-deck behavior since the bulk explosives in the column impart a shock into the air-deck where the air shock then passes through the air-deck at a rapidlyattenuating velocity. Through both high-fidelity modeling and shock physics theory it is shown that theresulting pressure in the air-deck is two orders of magnitude less than the detonation pressure of theexplosive."

Jan 1, 2017

By Robert Hopler

A detonator is a copper tube about a quarter of an inch in diameter and an inch and a half long, closed at one end and containing in the closed end a small charge of fulminate of mercury, which has been found to be the best explosive for detonating dynamite. The fulminate charge is a very powerful explosive very sensitive to friction, lows or heat and very poisonous. When exploded it has an intense local action, shattering things in its immediate vicinity, but not extending very far away from the explosion. This kind of detonator is intended to be exploded by a spark from burning fuse.

Jan 1, 2014

By Josh Calnan, Paul M. Holmgren, Abigail N. Styer

Detonating cord is a staple of the explosives industry, used widely in the civil and defense industries. Detonating cord is a thin, flexible plastic tube filled with pentaerythritol tetranitrate (PETN). It has many applications in mining, construction and military disciplines. For civil applications, it is used to connect and initiate a series of blastholes in a desired pattern. In the defense sector, it can be used as a detonating agent, a priming agent or alone as an explosive charge. Research has been done to understand the initiation and detonation physics on the detonating cord. However, its sympathetic detonation characteristics needed to be further analyzed.

Feb 1, 2020

By L D. Lawrence

Certain blasting applications are more prone to the generation of significant levels of nitrogen dioxide post blast fumes, more commonly referred to as after blast smoke, generally ranging in color from dark yellow to bright red. This paper reviews basic background chemistry defining the observed fumes and attempts to correlate geology, blast design, and explosive composition effects on the level of nitrogen dioxide that can be observed in various blasting conditions. Additionally, a test setting for evaluating the generation of post blast fumes is presented with pertinent test data detailing generic explosive formulation modifications which effect the overall level of post detonation generation of nitrogen dioxide.

Jan 1, 1996

By Wes Bender

Considering the current interest in Global Positioning System (GPS) usage, it might be timely to look at a more efficient means of utilizing these instruments. The GPS system currently utilizes 28 satellites (4 are spares) circling the earth in an inclined orbit. Normally at least six satellites are within your area of reception at any given time. The satellites broadcast an extremely accurate time signal and an almanac containing all the satellites’ orbital data. This information is updated regularly as the satellites circle the earth. Your GPS receiver, once it has picked up one satellite’s broadcast, can then determine which other satellites should be available for plotting.

Jan 1, 2002

By : D. Lawrence

Certain blasting applications are more prone to the generation of significant levels of nitrogen dioxide post blast fumes, more commonly referred to as after blast smoke, generally ranging in color from dark yellow to bright red. This paper reviews basic background chemistry defining the observed fumes and attempts to correlate geology, blast design, and explosive composition effects on the level of nitrogen dioxide that can be observed in various blasting conditions. Additionally, a test setting for evaluating the generation of post blast fumes is presented with pertinent test data detailing generic explosive formulation modifications which effect the overall level of post detonation generation of nitrogen dioxide.

Jan 1, 1996