Search Documents

By Enver Alan

This Research & Development (R&D) study was conducted in the field of applied blasting engineering in Ethiopia, within the AKH Railway Project, which was built in Girena, within the boundaries of the province of Mersa, in the Basalt Quarry at km 346, Ashangi Formation, occured in Eocene geological time in the aphanitic trachibasalt. Under the scope of the study, which has been performed to determine the effects of the artificial discontinuities at different depths and the effects of artificial discontinuities through structural damage risk, three test areas, at the same location and same formation, were considered. Six numbers of artificial discontinuities, each 10 m (32, 81 ft) transverse, were created by using pre-splitting and drilling-blasting technology. The number of sequential artificial discontinuities on each test area is two and they have the same length. The length of artificial discontinuities are; 6,80 m (22,31 ft) at the first test area, 13,60 m (44,62 ft) at the second test area and 17,00 m (55,77 ft) at the third test area respectively. The distance between sequential artificial discontinuities is 8 m (26,25ft) on each test area. Thirty-one shots were executed in order to produce vibration (10 shots on the first test area, 11 shots on the second area, 10 shots on the third test area). One hundred and twenty-three seismic recordings were obtained during the execution of the shots by using 4 seismographs. The closest distance between the shot points and the nearest measuring station is 5,30 m (17,39 ft). During the shots, the rock was cracked and there was no fragmentation and/or fly rock. At the first test area, measured PPV values are between 25,40-127,00 mm/s (1-5 inch/s) before the first artificial discontinuity and less than 50,80 mm/s (2 inch/s) after the second artificial discontinuity. At the second test area, measured PPV values are between 76,20-177,80 mm/s (3-7 inch/s) before the first artificial discontinuity and less than 76,20 mm/s (3 inch/s) after the second artificial discontinuity. At the third test area, measured PPV values are between 50,80-279,40 mm/s (2-11 inch/s) before the first artificial discontinuity and less than 50,80 mm/s (2 inch/s) after the second artificial discontinuity. Peak reduction rates in Peak Particle Velocity (PPV) values determined by measuring as follows: In the first test area 95,77% (106,00 mm/s to 4,48 mm/s) (4,17 in/s to 0,18 in/s), in the second test area 79,77% (176,00 mm/s to 35,60 mm/s) (6,93 in/s to 1,40 in/s), in the third test area 95,85% (from 205,00 mm/s to 8,55 mm/s) (from 8,07 in/s to 0,34 in/s). The arithmetic mean of the differences of PPV values (decrease rate) is 82,66% in the first test area, 69,37% in the second test area, and 92,03% in the third test area. The highest sound value is 138,50 dB and is defined as “noise”. When the measured parameter values are examined it was determined on the USBM norm graphs that these vibrations carry a risk of structural damage in the region before the first artificial discontinuity. While passing through artificial discontinuities the vibrations progress by losing energy and the vibrations passing through two artificial discontinuities do not carry structural damage risk under current conditions.

By Connie Postupack

The purpose of the workshop is to show the effect of various blasting factors on the overall results.

Jan 1, 1994

By Stewart A. Silling, Dale S. Preece

The two key results of rock blasting are fragmentation and movement of geomaterials. Movement/flow of the blasted rock is often referred to as heave. Modeling the movement of full scale blasting is now possible with 3D distinct element models and parallel processing.

Jan 1, 2016

By E. McCullough, D. Preece, M. Ortel

Geophysical explosive charges are used in mineral resource exploration. They are detonated subsurface and radiate sonic waves into ground monitors, which detect the vibration waves and their interaction with underlying geologic strata. Geophysicists perform computer analyses of the waves reflected from the strata to determine their depth and thickness (Strobel, Berger & Schaefer, 2012). The purpose of this research is to determine how the detonating explosive charge interacts with the adjacent ground and how the induced waves propagate through the surrounding medium. Furthermore, it is necessary to optimize the location of the initiation point within the charge. Establishing both the direction and intensity of the waves will allow geoscientists to refine and optimize geophysical studies that employ explosive charges.

Jan 1, 2013

By Will Hunt, Darren Thornton

In March of 2013, an undisclosed gold mine (MINE X), located in the Western United States, performed blast movement monitoring of three blasts occurring in one of two active pits. Blast Movement Monitors (BMMs) were placed in the bench before blasting, and located after the blast to determine vectors of movement. Using blast movement software, ore/waste boundaries were translated. These locations were compared to MINE X’s standard ore translation procedure, which consisted of moving polygon boundaries by 17.5 feet (5.3 m) in the burden direction of the blast hole pattern. This translation amount, identified by MINE X as “average” motion, had been ascertained by performing a previous blast movement study.

Jan 1, 2014

By William C. B. Gates

Demolition blasting next to an active railroad can be very challenging because of track safety, blasting vibrations, potential track fouling by blast debris, and short work windows on a live track. Recently, in eastern Washington, one of the major railroad companies has been aggressively constructing a second main track to accommodate the expected increase in rail traffic of natural resource products. To accommodate construction of the second line, the railroad company used blasting demolition techniques to remove an old railroad trestle pier on the Milwaukee Road that was in the footprint of the new track bed. The trestle bridged the present rail line and flanked the track with two massive 550-ton (499 tonne) twin-columned steel reinforced concrete piers. The railroad contracted with a specialized contractor to remove the south pier using blasting demolition techniques. The blasting design presented the following challenges: blasting during live track conditions and short work windows; designing a V-notch blast pattern to ensure the pier fell away from the live track; drilling, loading, and timing of the shot; maintaining blasting vibrations at the track below 4 in./sec (102 mm/sec); maintaining ambient overpressure noise below 133 dB; control of fly rock and debris; and track protection and emergency debris removal plan.

Jan 1, 2016

By Corry Goumans, Dwayne Wallace

"On July 1, 1997, a rockslide occurred on the I-40 in Hayward County, North Carolina that completelyblocked all lanes and disrupted traffic flow in the region. Remedial measures were undertakenimmediately in order to open traffic, however on-going geotechnical investigation revealed stabilityconcerns that necessitated closing the highway to ensure public safety. Access to the top of the slope was available only from the bottom of the slide on the Interstate I-40. Excavation and trim blasting started from the top and along the west slope of the failure, however, additional geotechnical evaluation indicated that slope stability remedial measures were required to support the western rock slope mass."

Jan 1, 1999

By Frank Hirthammer

Productivity, customer relations, and effectiveness of work depend to an ever-increasing extent on a functioning logistics system tailored to the needs of the user. Of course, it is not possible to cover and explain all aspects of the logistical requirements of even a small part of an industry, in a single article. The article speaks specifically about the particularities and differences in the logistical requirements in the explosives sector. Starting with questions of safety, handling and quality up to the legal basis, there are special requirements regarding the logistics in the explosives sector. The results of innovative logistics solutions are presented using three examples from daily work practice.

Jan 1, 2019

By Neal Lee, Braden T. Lusk, Brendan McCray

Determining the minimum amount of inert material that can be used between explosive columns is a complex problem. Using too little inert material can result in detonator/primer failure, either by sympathetic detonation of or failure to fire of the subsequent explosive column(s). Propagation type failure results when inert material length between charges is small enough that the subsequent (delayed) deck fires more or less instantly. In this situation, the primer, detonator, or bulk product is initiated by the shock wave from the earlier firing deck. This type of failure may be un-noticed until the vibration/airblast report is examined.

Jan 1, 2016

By Enrique Albarrán, Julian Hernández

"In 1942 The “Presa Mixcoac” dam was built, along with 15 other dams, to control the rain fall waterin the mountains west of Mexico City. Mexico City’s population at that time was around 1.5 millionpeople, and the dam was way out of the city."

Jan 1, 2016

By John Watson, Tom Treleaven

This guide presents nur-nerous patterns that provide 8 millisecond separations between initiated charges. The guide is tabulated in seven sections to provide Quick reference by number of decks or bunch blasting. The pattern IS presented in the section where the highe!$ number of decks works. It should be noted that patterns applicable to multipledackshwtings are alsoapplicsblefor fewer decks.

Jan 1, 1995

By Charolett Hayes, A. L. Russell, Anthony J. Bednar, Jared Smith, Valentine A. Nzengung, Stephen L. Pilcher

The manufacture of Energetics Materials (EM), including maintenance and demilitarization of munitions causes dangerously high levels of explosives residues to be harbored in building features. The two commonly approved methods of decontaminating energetics contaminated equipment and building features are thermal treatment and steam washing. The current regulatory environment is generally becoming more stringent and unfavorable to thermal and steam decontamination because of their adverse impact on air, soil, and water and their ineffectiveness to completely remove accumulated energetics from foundation cracks, internal and external piping, voids in walls and ventilation systems, and internal cavities of fixed equipment. However, chemical destruction of energetics, especially high explosives, is gaining acceptance as a safer, cost-effective and environmental friendly alternative to thermal and steam decontamination. Organic explosives, including nitramines and nitrate esters are oxidized organic compounds that are susceptible to chemical oxidation and reduction reactions. Under suitable conditions, a chemical reagent consisting of sulfur-based bulk reductants (neutralent) commercialized as MuniRem generates highly reactive free radicals that very rapidly degrade many energetic compounds to innocuous end products while stabilizing metals as the insoluble metal sulfides.

Jan 1, 2016

By Türker Hüdaverdi, Özge Akyildiz

"In this research, image analysis technique, Kuz-Ram and KCO Models were used to examineefficiency of the quarry blasts. Investigations were performed in Cendere region, Istanbul. As a firststep, image analysis software was used to determine particle size distribution of muckpiles.Additionally, the results of KuzRam and KCO fragmentation models were compared to the results ofthe image analysis technique. The efficiency of KuzRam and KCO models was investigated and theimportant points to be considered were explained. Additionally, the effect of the rock factor valueson the size distribution curves was investigated. The blasthole diameter is 89 mm. (3.5 in) in thestudied quarry. Each measured blast has a different burden, spacing and stemming length. Blastholes was drilled in a staggered pattern. It is concluded that, KuzRam and KCO models can be successfully used to determine fragment size distribution in Cendere Region Quarries, Istanbul. Site engineers can predict blast fragmentation using the theoretical fragmentation models and they may change blast design parameters before blasting operation if necessary. It is possible to calibrate the Kuz-Ram and KCO fragmentation models using the measurements obtained by image analysis technique."

Jan 1, 2016

By Peter Duniam, Stephen John Brace

2000 HIGH-TECH SEMINAR Blasting Technology, Instrumentation and Explosives Applications Orlando,Florida,USA July24-27,200O. Objectives:- After completing this session 1. Explain safety issues 2. Do simple initiation design 3. Describe how the system works 4. Demonstrate scanning, hookup, testing and firing 5. Describe hot to do a post blast check 6. Explain how to treat misfired detonators

Jan 1, 2000

To meet the energy requirements, hydroelectric projects are planned and executed in many countries. Though these projects requires a high capital investment, the returns are regular with minimum maintenance after commissioning of the project and are ecofriendly. Bhutan is situated in the eastern Himalayas and covers an area of 38,394km2 (14824.01sq. miles. It is bordered by India in East, South and West and by Tibet in the North. The hydropower potential of the country is estimated at 30,000MW, out of which around 5% has been harnessed.

Jan 1, 2016