Search Documents

By K. Taylor

In surface coal mining, the performance of a shovel through blasted muck is one of the key performance indicators of the blast. Historically, performance has been measured qualitatively based on operator feedback or visuals of the muckpile. More complete shovel data, such as loading times and GPS location, is available from most fleet dispatch systems that are already in place at most truck and shovel operations. With some database and analysis skill, the drill and blast team can take advantage of this data to make targeted improvements to drill and blast designs. An area typically known to cause trouble for shovel operators at this operation are blast boundaries. Blast patterns with and without design changes along the boundaries were studied in this case study. The instantaneous loading times for each shovel pass were analyzed for 75 blasts across two subsequent benches with similar firing direction and shovel paths. The benches were split into three categories: Main body of pattern, boundary with design change, and boundary with no design change. The loading times from the main body of the patterns and where the design change was utilized in the boundary had similar prevalence of good loading times. However, boundary areas without the deign change had approximately 2% more prevalence of poor loading times compared to the main boundary of the pattern. Improving the dig rates through the boundaries up to the average loading time would result in approximately 280 hours taken off the total loading time for one bench. By quantifying the shovel’s performance by GPS location, the drill and blast team can decide how much of a design change is needed, can target precisely only the areas that require it and measure the impact of any changes made

Jan 1, 2024

By Ronald L. Cocklin, Vivian Patz

Blasting techniques are becoming increasingly sophisticated as the need for improving mining efficiency grows. One of the areas of blasting that has never been fully exploited, due to a lack of a control and reliability, is the initiation of explosives. Expert Explosives have taken on the challenge to not only provide an initiation system that offers control and reliability, but also provide benefits that are critical to enhanced mining productivity. These benefits can only be delivered through the medium of electronics and computer controlled systems.

Jan 1, 1995

By Visitor Makiyi, Chris Batten

Poor coal recovery due to coal damage or loss caused by blasting can have a significant impact on a mining operation. Increasing coal recovery by reducing blast damage can provide a significant opportunity for coal mines to maximise their revenue and reduce their operating costs. This paper provides details on advanced drilling and blasting techniques used throughout the coal industry globally to prevent coal damage and movement during blasting. Typical coal loss and damage mechanisms are explained, along with how each of the applied techniques works to minimise the impact of each mechanism. Key requirements for a coal loss reduction program are detailed with typical design parameters used for each of the methods discussed. The positives and negatives of each method are also provided to enable comparisons and help determine suitability for a particular coal mining operation.

Jan 21, 2025

By Ery Wardhana, Fathur Rozaq, Jeff Averett, Nella Lubis, Carl Lager, Herry Saputra, Rudolf Sitorus, Relinda Sanistrya, Hormat Sinaga, Andhiko Maharjono

Efficient drill and blast operations are crucial for achieving optimal fragmentation, productivity, safety, and operational efficiency for the mining industry. However, conventional methods face significant challenges, including manual borehole marking and retrieval by survey teams, limited real-time data monitoring, excessive borehole collar deviation affecting blast quality, suboptimal drill productivity impacting person-hours and fuel usage, subjective judgment by drill operators on voids during drilling, and limitations in explosive charging design that do not match rock hardness. Rock hardness determination using lithological data from exploration models is often inaccurate due to the interpolation effect of wide drilling distances and depths, necessitating manual field verification using drill cuttings and historical blasting results. Furthermore, using single-density bulk emulsion throughout blast holes leads to suboptimal results due to varying rock properties. This study introduces an integrated approach that combines smart drilling technology with advanced emulsion technology to enhance drilling and blasting efficiency. The method utilizes smart drilling technology with GPS for precise borehole placement, Measure While Drilling (MWD) loggers, and real-time performance monitoring. Additionally, it integrates a smart Mobile Processing Unit (MPU) featuring a digital system and an automated gassing system (AGS). This setup allows for multiple emulsion densities within a single blast hole, customized to match the hardness index parameters determined from MWD data, addressing the challenges in drilling and blasting operations. The study evaluates the effectiveness of this innovative approach through comprehensive field trials and data analysis. While maintaining the digging rate according to production targets, key metrics such as drilling productivity, drilling accuracy, fuel consumption, powder factor, drilling and blasting cost, and fragmentation size were compared between conventional and new methods. Results showed a 56% increase in drilling accuracy, a 23% increase in penetration rate, a 19.6% increase in drilling productivity, and a 29% reduction in fuel consumption. This new method decreased the powder factor by 5.2%, impacting the drill & blast cost reduction by 2.3%. Moreover, fragmentation size improved by 12.8%, demonstrating the effectiveness of rock hardness-adjustable emulsion density in achieving better blast energy placement. In conclusion, integrating smart drilling and advanced emulsion technology significantly enhances drilling and blasting efficiency. This approach offers substantial cost savings and operational improvements, providing a strong rationale for adopting this innovative method in drilling and blasting activities.

Jan 21, 2025

By Ola Lindahl, Mark Irving, John Hutchings

"Blasting is a process starting with a geometric description of the block of rock and ending with a pileof fragmented material. A key step in improving the productivity and quality control over the processis the integration of blast planning software, explosive delivery control systems, and blast recordingwithin one seamless customer solution."

Jan 1, 1997

By J. P. Proulx, Richard O’Meara, Ruilin Yang

A blast optimization project was carried out at an Open Pit Metal Mine using the Multiple Blasthole Fragmentation (MBF) Model and the Multiple Seed Waveform (MSW) blast vibration model. The aim of the project was to optimize rock fragmentation of the ore blasts to significantly increase metal recoveries while keeping the blast vibration levels at the highwall under control. The project also examined the blasts in the waste rock using the Fragmentation model to expand the blast pattern and select economical explosives for drill and blast cost savings while minimizing any adverse effect on the dig rates. Two sets of near field signature blasthole tests were conducted in both hard ore and relatively soft waste rock. The information from the near-field signature blasthole vibration was used as input to both the MBF and MSW models, as site specific geological information interacting with blasting. The implementation of the full blast design is also input to the MBF and MSW models. A production blast for each rock type was monitored for blast vibration and rock fragmentation. The full blast information and the blast results are used to calibrate and validate the models. The Fragmentation and Vibration model were established for the two rock types at the mine. At each site the Fragmentation modeling was conducted in parallel to the Vibration modeling to ensure blast vibrations were under control while the rock fragmentation was improved. The Fragmentation MBF and MSW are each an integral part of the blast optimization tool. Various scenarios using different explosives, hole delays and blast patterns were modeled for rock fragmentation and blast vibration. The recommendations from the modeling project were to be field trialed at the mine. The implementation of the recommendations was expected to help the mine significantly in terms of the mining economics, and high wall stability and safety.

By Cam Grundstrom

The Ok Tedi Mine is a large open pit copper and gold mine located in a remote section of the Western Province, Papua New Guinea, with an annual rainfall of over 10 metres. Ok Tedi mines an average of 205,000 tonnes per day. A strong working co-operation between the mine operator (Ok Tedi Mining Limited) and the explosives contractor (ICI Explosives Asia / Pacific) has led to progressive development of bulk emulsion formulations to meet site-specific needs, continued improvement to blasting applications, and competency based training programs for the national blast crew.

Jan 1, 1997

By Miquel Lamadrid, Changshow Sun, Chris Johnson

To reduce blasting overbreak and improve stope stability, several new blast designs were proposed for current and future stopes. Based on the analysis of the powder factor, and the extent of damage zone, the appropriate new blast design was selected. Excellent results were achieved from the new blast design. Comparing the new blast design with the old one, the largest of the overbreaks decreased more tan two times and average overbreak reduced more than two times. The new blast design is currently applied in all mining zones in Leeville underground mine.

Jan 1, 2008

By Alan Tordoir, Mark Roberts

The drill and blast process is a critical function within the production cycle which significantly impacts the ability of an operation to effectively meet its safety and production targets. Acknowledging that D&B design and reconciliation practices were conducted inconsistently across operations, a Group wide initiative was launched to embed a standardized design and reconciliation platform in line with the company’s Operating Model principles. A technical system was selected to deliver the digitalization of critical D&B information and enable ‘analyze and improve’ routines for design compliance monitoring and downstream productivity optimization.

Jan 1, 2019

By Carlyle F. Bunn

The source of the standards adopted by the Occupational Safety and Health Administration are outlined. Preplanning to eliminate violation of the standards and improve overall job efficiency are discussed.

Jan 1, 1975

By Lawrence Mirabelli, William Hissem, Gary Veltrop

Capital Quarries Company, Inc., Jefferson City MO produces aggregate products for road base, asphalt, concrete and concrete block. With their production quantities small in comparison to those produced by the goliaths of the aggregate industry, they find it necessary to constantly stay on the leading edge of best practices for cost control, process and production improvement to sustain a successful business. In the words of Eric Strope, President, “The safety of our employees is foremost. They all work hard each day. They are focused on keeping our cost to manufacture down. As I see it, we cannot work any harder so we must work smarter!”

Jan 1, 2009

By Michael Swisdak, John Tatom, James Tancreto

In 2002, testing was proposed to generate needed data to assist in developing improved explosives safety standards within the US Department of Defense. This testing emphasizes two major areas: (1) full-scale donor/acceptor trials examining debris generation and acceptor response and (2) debris perforation testing of representative roof/wall materials. The full-scale donor/acceptor trials are referred to as the SciPan series. The first three tests in the SciPan series have been completed, as has the first phase of the SPIDER program. This paper describes the status and future of these testing programs, reasons for choosing specific tests, potential benefits, and planning for future phases.

Jan 1, 2006

By John J. Ridgeway

Habits take us where we were yesterday and attitudes tend to keep us there. Until recently, little had been accomplished to improve conventional explosive energy for use offshore. But with the special requirements of the Offshore Oil Industry, and particularly in the North Sea, most equipment, products and services must be specialized as well. Previous attempts to excavate a trench for a sealine in surf areas had been impossible to accomplish. But with the application of safe, controlled explosive energy, an impossible task to accomplish yesterday has now become a reality. Explosive energy, often overlooked as a convenient and economical offshore tool, excavated a clean trench underwater for a 40" sealine at Djeno in the African Congo recently.

Jan 1, 1977

By Michael Olmsted

Inspection of boreholes prior to blasting can result in cost reductions as well as increases in efficiency and safety. Until recently, borehole inspection was performed in two manners. For simple inspections, a flashlight was used to view the upper part of the hole. More thorough inspections were performed with long tool strings developed for oil field applications. Borehole inspection tools developed specifically for mining and blasting applications have now been developed. Video Cameras developed for borehole inspection have been in service for several years. Now measurement tools are available, developed specifically for mining.

Jan 1, 2000

By John R. Schuring, Walter Konon

The 2.0 in./sec. peak particle velocity criterion traditionally used to protect structures from blast induced vibration damage is non-conservative for landmark structures. Various factors which must be considered in establishing vibration criteria for landmark structures are discussed. Existing criteria by past investigators for this class of structure are presented.

Jan 1, 1984

The most common method for identifying the potential for blast damage is the peak particle velocity. But this can depend on many factors such as the type of blast, explosive, confinement, timing and the rock mass. The value must then be used to estimate damage. But the amount of damage will depend on the rock mass quality and the excavation size and shape. The amount of damage that can be accepted will depend on the purpose of the excavation. This paper presents a logical, but very approximate, procedure that the mining engineer can follow in order to assess the potential for damage in the control of that blasting.

Jan 1, 1987

By Mark A. Williams, James D. Humphrey

Without question, draglines are one if not the most effective tools available to the surface mining industry for overburden handling. With few moving parts and a two- or threeman crew, this machine silently sits and chews into millions of yards of overburden annually. A 100 cubic yard machine operating for 30 years will excavate three-quarters of a billion yards of material during that time. That is 750,000,OOO yards of material!

Jan 1, 1990

By Roger L. Keller

Cautious, productive blasting is employed in the adaptation of a mobile crushing system extending into a highway through cut. In Hong Kong's final chapter of infrastructure development in preparation for handover of sovereignty, the vital link to the new governing country, The People's Republic of China, is now being completed. The Ting Kau approach and Tai Lam tunnel involves the removal of 6 million cubic meters of rock by drill and blast means. For the main-cut excavation (because of removal Iogistics) a unique adaptation of a Lokotrack crushing and conveyor transfer system is being used. The characteristic narrow working area associated with through cuts, positioning of equipment, and production demand place many limiting factors on blasting. Add to this the strict criteria set by the local regulatory body, the Hong Kong Mines Division, and nearby vibration limiting structures (13mm/sec), has led to highly cautious, fine-tuned blasting.

Jan 1, 1998

By Don Bachman, Larry Heywood

Artificial release of snow avalanches, through the use of explosives, is a necessary component of safety planning and operations for ski areas throughout the Western United States, as well as in other alpine regions of the world. Climatic, meteorological and terrain factors leading to the development of avalanche conditions, in addition to release mechanisms and magnitude of the avalanche problem to ski areas will be discussed.

Jan 1, 1999

By Jim Breedlove, Stephen P. Case, Mike Fabio

To meet salt production needs over the remaining life of the Cayuga Mine at Lansing, New York, the Salt Division of Cargill, Inc. decided to build a new underground screening plant. The new plant required a chamber 50 feet wide by 250 feet long and nearly 70 feet high. On advice of their mining contractor, Dynatec Mining Company, the company chose an ingenious excavation method similar to sublevel stoping. This method eliminated the need for an access ramp, reduced equipment needs and excavation time substantially.

Jan 1, 1996