Search Documents

By Mark Fritzen

Drilling and blasting near residential or business inhabited areas may expose people to blast induced vibration. Many of these people have never been exposed to blast vibration and airblast which can cause a variety of reactions ranging from indifference to anger. Blasting contractors seeking to minimize the impact of blasting to neighbors of the project will plan for a public relation plan which begins at bid time. The public relations plan cost will be included in their proposal and a variety of methods may be included including, door to door contact, letters, pamphlets, telephone calls, and the use of an independent consultant to conduct a pre-blast survey. By raising the awareness of neighbors to a blasting project the blasting contractor may reduce the anxiety and stress of unannounced blasting vibration and airblast. This helps everyone associated with the project from the project owner(s) to the blasting contractor.

Jan 1, 2000

By Qi Jingyue, Wang Zhongquian, Yang Nianhua

Qinling Tunnel is the longest tunnel in China. The rock stratum is very hard rock - intact mixed gneiss. At the beginning of the construction, drift-pilot excavation is very costly due to the use of regular drill and blasting methods. After tests on the acoustic impedance match between rock and explosive, watergel explosive, which has a high velocity of detonation and high brisance, has been used for hard rock blasting. In addition, different cut plans have been compared. It was found that four-large-hole cut is the most effective. And the number of drillholes and specific charge cut down and the average advance reaches more than 94% of the blastholes depth. Thus, the difficult problem of hard rock blasting in drift pilot is successfully solved, while safe and quick construction is guaranteed.

Jan 1, 1998

By Norman Paley, Zachary Pickett

The Red Dog Mine is a high-grade zinc-lead mine located in northwest Alaska which began operations in November 1989. In June 2014 the upper half of a charge in a trim shot in the Aqqaluk pit deflagrated. No other holes in the area were observed to react and the remainder of the pattern was shot without incident. This was the only known case of a deflagration in the 25 years of operations. As part of the investigation into the cause of this incident rock samples were obtained from the area of this hole and from other areas in this pit. The samples were assayed and tested for reactivity using the Reactive Ground Catalyzed Adiabatic test. Approximately half of the samples were found to be reactive with standard blasting agents. Unexpectedly, some of these were found to be reactive with blasting agents doped with urea to act as an inhibiter. Relationships between element grades and reactivity and between Specific Heating Capacity and reactivity were developed; however, the small sample size led to these models having an unrealistically large number of geological model blocks tagged as reactive. A program to better understand the behavior by testing more samples was initiated. Drill core was selected based on the predicted level of reactivity using the aforementioned relationships. The samples covered a greater range of grades and lithologies and included rock from the soon to be developed Qanaiyaq pit. The samples were dry pulverized then split for elemental assay, Reactive Ground Catalyzed Adiabatic testing, Specific Heating Capacity (SHC) determination, and X-ray Diffraction (XRD) mineralogical analysis. From this data, a Red Dog Mine specific assay based classification for separating reactive from non-reactive ground was developed. Furthermore, it was possible to divide the reactive ground into two subgroups: i) rock which reacts with ANFO-emulsion blends even when manufactured specifically with a reactivity suppression agent like urea and ii) rock which reacts with ordinary ANFO-emulsion blends only when a reactivity suppression agent like urea is absent.

By Thomas P. Dowling

Since the 1950's, blasting practices have undergone many revolutionary changes. Some of the more radical departures have involved, in addition to high speed drilling equipment, a myriad of new explosives, blasting agents, boosters, initiators, initiating systems and delay devices. The introduction of ANFO in the mid 1950's as a blasting agent seems to have instigated a trend toward the development and use of less sensitive blasting agents. The evolution of slurries or water gels has produced dense, high strength, water resistant products which has further promoted this trend away from the more sensitive, conventional explosives.

Jan 1, 1975

By Nobel Insurance Service

[Executive Director’s note: ISEE is committed to continuing its efforts to ensure that blasters be made aware of the issue of migration of carbon monoxide resulting from blasting operations. In the July/August 2001 issue of the J o u rnal we printed excerpts from “Carbon Monoxide - The Silent Hazard,” an article from the Safety Update, published by Nobel Insurance Services. We also re minded readers of the text from the 17th edition of the ISEE Blasters Handbook in its section on trench blasting as follows: “...consideration must be given to the proper venting of gases generated from the blasting. Should those gases spread laterally rather than vent directly to the surface, the gases may travel underg round and finally vent well outside of the planned area. Such events may be caused by the strata, soil conditions or root systems, or existing and/or abandoned utilities or other man-made structures. In the worst situation, gases resulting from the detonation such as CO2, CO, and/or N Ox may travel through the strata and find their way into basements of nearby homes or businesses.” While incidents are rare, a number of cases in re c e n t years have resulted from outdoor blasting operations p roducing carbon monoxide gas that has migrated t h rough the earth and accumulated in nearby enclosed spaces. T h e re are steps that a blaster can take to be proactive in preventing incidents. These steps and studies of the occurrence have been expertly presented in several papers presented at ISEE conferences and included in the ISEE Conference Proceedings, available th rough the Blasters Library. In addition, Material Safety Data Sheets provided with explosives used in surf a c e blasting should provide additional information on gases p roduced by detonation. Below, we have reprinted the IME white paper, entitled “Fumes from Blasting Operations.” The paper underscores the unique set of circumstances that combine to contribute to high concentrations of CO measurements in underground, enclosed spaces following the detonation of explosive materials and provides recommendations to blasters

Jan 1, 2004

By Farshad Rashidi Nejad, Ali Asgari, Sanaz Norouzi

Blasting is known as the first step of rock breakage in mines. An indication of the importance of blasting is that more than 1 billion kg (2.2 billion lb) of explosives are used annually in Australia and 3 billion kg (6.6 billion lb) in the United States for rock breakage, more than 85% of which is used in the mining industry. The notion that blasting, as the first step of comminution, plays a significant role in crushing and grinding energy consumption is not an unfounded thinking. It can be noted that the comminution electrical energy consumption decreases in these ways: First, if the feed size to the primary crusher is decreased, less energy will be required to crush the ore to the same product size. Second, a decrease in work index (Wi) related to additional macro fracturing and micro fracturing within individual fragments.

Jan 1, 2015

By B Mohanty

The current basis for rating of commercial explosives is examined, with particular emphasis on calculated bulk and weight strengths, detonation velocity and underwater energy measurement. The calculated strengths still form the basis for selecting explosives for most blasting applications, with the measured detonation parameters serving only as a measure of the quality of the explosive. The major drawbacks with this approach are discussed, in view of the non-ideal nature of commercial explosives and the field conditions prevalent during the blasting operation. A unified approach to rating explosives on the basis of blasting performance rather than calculated energy alone is presented for various types of explosives. This incorporates the relevant field parameters as well as the effect of non-ideal reactions, both of which affect explosive energy release and its transfer to target rock.

Jan 1, 1988

By Adrian J. Moore, Alan B. Richards

Airblast overpressure levels can commonly be increased by up to 20 decibels (dBL) by the effects of meteorology, due to inversions and wind shear. Existing atmospheric refraction models can provide a good evaluation of the effects of meteorology, but have been limited in the accuracy of their outputs by the accuracy of the meteorological data that is available for input. This paper uses case histories from open-pit coal mine blasting in the Hunter Valley area of Australia to provide examples of increases in airblast due to inversions, wind shear, and a combination of both. It gives details of our experience of the accuracy with which predictions and assessments can be made using meteorological data of various levels of accuracy, and on the design buffer that is required to prevent the exceedence of airblast limits. The accuracy of meteorological prediction and assessment will shortly be improved by the use of sounding equipment that gives continuous measurements of temperature and wind velocity at significant levels above the ground. The paper also gives details of an industry funded research project that aims to permit the effective use of this data at distances many kilometres (km) (miles) from the location of the sounding equipment, and to develop a short term predictive model that will permit the amount of meteorological reinforcement that will occur at firing time to be determined before a decision is made to tie up a shot.

Jan 1, 2005

By Perry Sisk

In order to protect nearby structures during a blasting project, a peak particle velocity limit is often stipulated by a government agency or the owner of a particular structure. At the start of a blasting project, a preliminary estimate for the minimum scaled distance is often determined using a vibration prediction equation before any site-specific data have been obtained. Reasonably conservative assumptions are typically made for the unknown input variables in the vibration prediction equation until site-specific blasting data have been obtained and evaluated. Although this approach is prudent, it provides no assurance that the peak particle velocity values generated during the initial phase of the project will be below the specified limit.

Jan 1, 2013

By Gregory L. Hempen

"Pressure waves from submerged blasting can have adverse impacts on nearby structuresand on aquatic fauna. Underwater blasting is not allowed for some situations withoutmitigation of these adverse pressures. Two states currently require bubble-curtain, pressurereduction of underwater shooting for environmental concerns. St. Louis District hasconducted field monitoring of scaled testing and demolition shooting with air-screenmitigation. The deployment of compressed-air manifolds and air-entrained packagesheeting effectively reduces underwater blast pressure. St. Louis District is preparing areport on optimum use of underwater-blasting mitigation measures."

Jan 1, 1993

By C. Yi, D. Johansson, C. San Miguel, M. Wimmer

Sublevel caving (SLC) is a mass mining method based upon the utilization of gravity flow of blasted ore and caved waste rock. Production blasting has significant impact on the efficiency and productivity of SLC output, affecting material fragmentation, flow and recovery. Misfires could occur during blasting in SLC, which results in the loss of explosives and poor fragmentation. Usually, the blastholes are top-initiated with redundant lower primers set at + 25 ms as a precaution. If the top primers fail, the lower primers may initiate the explosive, which will induce out-of-sequence delays that can influence fragmentation and gravity flow. This work investigated the impact of misfires and out-ofsequence delays on fragmentation and gravity flow through numerical simulations using a coupled finite element and discrete element method. Different scenarios of misfires and out-of-sequence delays were studied, and the fragment size distribution was obtained to evaluate the blasting performance. The material flow behaviour was investigated to assess the gravity flow process. The results indicated that misfires significantly affect the fragmentation and the gravity flow process while the effects of out-of-sequence delays are not so significant for the investigated cases

Jan 1, 2024

By Pavel A. Torres, Darwin Torres, Sandro Huaman

Given the limited efficiency of blast-induced ground vibrations prediction empirical models, due to the complex geological system from a Peruvian mine. An artificial neural network was built in order to get better results. More accurate and precise predictions allowed the generation of blasting domains for future designs and decision making.

Feb 1, 2020

By Cceliksirt, V Erkan

This computer program has been developed under the field conditions for use in control of surface drilling-blasting operations. This paper outlines the relevance of fragmentation to quarrying, open pit mining or road cutting and key features and operating principles of the software (DelPat for Windows 95).

Jan 1, 1998

By Ettore Contestabile, Cameron Thomas

Implosive-type electrical/mechanical connectors such as XECONEX have been used extensively for joining electrical transmission lines. This implosive action of explosives has also been applied to other forms of high energy metal working with excellent results. However, as with many other products, the inherent blast energy of these units has caused some environmental concerns especially when used in proximity to inhabited areas.

Jan 1, 1995

By Ettore Contestabile, Cameron Thomas

Implosive-type electrical/mechanical connectors such as XECONEX have been used extensively for joining electrical transmission lines. This implosive action of explosives has also been applied to other forms of high energy metal working with excellent results. However, as with many other products, the inherent blast energy of these units has caused some environmental concerns especially when used in proximity to inhabited areas.

Jan 1, 1995

By Q Liu, P D. Katsabanis

Dust explosions in underground sulphide and oil shale mines result from the detonation of explosives in the blasting operations. Explosive composition, oxygen balance, priming and ideality of detonation were examined theoretically and experimentally in the presence of reactive sulphide dust. It was found that the temperature as well as the chemical composition of the gaseous products of detonation are the controlling parameters related to the explosive. Non aluminized, oxygen balanced emulsion explosives were proven to be relatively safe, while explosives creating combustible products were proven to be extremely dangerous due to the secondary flame they generate. Since a large number of dusty orebodies are often very friable, low density emulsion explosives are also examined for application in production blasting.

Jan 1, 1991

By J. Esterle, J. Kruttschnitt

Fragmentation modelling in soft rocks presents a challenge due to their propensity to further fragment after blasting during normal handling. Coal and some iron ore deposits are examples of materials that undergo significant degradation during the extraction, hauling and dumping process of the mining operation. The Kuz-Ram model is an empirically derived predictor of size distribution from blasting hard rock. Little breakage occurs during excavation and subsequent sizing of hard rock, so the measured Run of Mine (ROM) size distribution is essentially the same as the post-blast (before excavation) size distribution. However, for soft rocks, each step of the excavation and hauling operation imparts energy to the rock particles so the measured. ROM size distribution will be significantly different from the postblast size distribution. In order to calculate the ROM fragmentation at any stage of the extraction (or sizing) operation, the JKMRC has developed a model that combines both blast fragmentation and degradation through subsequent handling.

Jan 1, 2001

By Duane Skidmore, Calvin Konya

The supply crunch and cost rise for ammonium nitrate (AN) over the past year have been influenced by a number of factors. These include a general inflationary tendency, particularly great cost rises in fuel, and by a market condition in which demand for ammonium nitrate is great and supply is limited. Demand is largely confined to agricultural and explosives uses with explosives subdivided into mining, construction, and quarrying. The projections show that demand may be expected to increase markedly for the indefinite future in the agricultural and mining sectors of the ammonium nitrate market while fluctuating with indicators of economic activity for the construction and the quarrying sectors. Supply is projected to increase with plants being designed and built due to high need levels and commensurately high profit potential but not enough are planned to provide an equilibrium market. Constraints upon supply increases to match demand increases include shortages in the raw material, natural gas, high cost of investment capital, high equipment costs and long construction delays. The result should be, even under optimistic conditions, considerable shortage and resultant pressure for higher prices through 1979 for ammonium nitrate. The best hope for relief in the intervening years appears to be conservation. In blasting operations, the earliest and best proven route to conservation seems to be improved utilization available from application of highest available technology and most efficient current blasting practice.

Jan 1, 1975

By Cathy Aimone-Martin, Kristin Dunlap Kolden

Blasting was conducted for the Army Corps of Engineers (Corps) in the Columbia River near Saint Helens, Oregon during 2009 and 2010 to deepen the navigation channel as a final phase of a dredging project to accommodate larger container ships. The Columbia River Channel Improvement Project (CRCI) required 4 months to blast and dredge 300,000 yd3 (229,366 m3) of basalt from the bottom of the channel to allow Post-Panamax vessels with drafts up to 50 ft (15.2 m) access to the Ports along the River. Explosives charges were limited to 90 lbs (40.8 kg) per delay for the protection of fish and marine life in the area. A fish mortality study and marine mammal monitoring program was also required by the Corps. Underwater overpressure monitoring was required for each blast and peak overpressures measured 10 ft (3.1 m) above the river bottom 140 ft (42.7 m) from the closest blast hole were not to exceed 70 psi (483 kPa) with a cautionary level of 40 psi (276 kPa). Specifications required sampling rates of 500k S/s and PCB Peizotronics tourmaline pressure sensors. The Corps granted permission to co-locate additional ceramic-type sensors at different sampling rates to design redundant monitoring systems 140 and 300 ft (42.7 and 91.4 m) from blasting and develop a site-specific overpressure attenuation model for the project. This paper presents the correlations of overpressure with cube-root scaled distance factors, a comparison of measurements using three different pressure sensor systems, and a discussion of blast design influence on overpressure measurements.

Jan 1, 2014

By Alton Dunaway, Kevin Sullivan, Charles Gray, Doug Hall, Kevin Grant, Kelly Thiel, John Paulson, Bruce Leland, Cole Boyd

Beaver (Castor canadensis) are responsible for economic losses exceeding $4 billion over the last 4 decades in the southeastern United States alone. A large portion of these damages occurs to public roads and highways, forests, agricultural resources, and other property from flooding caused by beaver dams. The United States Department of agriculture, Animal Plant Health Inspection Service, Wildlife Services (WS) program is a non-regulatory Federal program directed by Congress to assist resource owners with managing damage caused by wildlife.

Jan 1, 2007