Search Documents

By Lon Santis

In 1923, Ralph Assheton compiled a report for the Institute of Makers of Explosives (IME) on accidental explosions in manufacturing plants. The report chronicles the type and amount of explosive involved in the event and the effects and distances to nearby buildings and workers for over 100 events from 1880 to 1916. Apparently, this report was never published but served as the origin of the IME’s first intra-plant distance table published in Pamphlet No. 3 in 1926. The effort was a parallel effort to the IME’s development of the American Table of Distances. The intra-plant distance table has never been changed by the IME and follows the US Department of Defense (DoD) standard very closely. This paper freshly compiles the data from the 1923 report and analyzes it with modern methods not generally available in 1923. Interestingly, the analysis indicates that the original intra-plant distance tables were established primarily to protect workers from serious injury and that preventing propagation was a side benefit. The data shows that a strong relationship exists between the probability of injury and the traditional K-factor. The data indicate that people in the open are better protected than those inside structures and that barricades reduce risk close to an event. Individuals at the intra-plant distance had a 95 percent chance of receiving no worse than a minor injury. A comparison of the data to explosive event consequence models indicate the models are overly conservative in regards to risk inside inhabited building distances.

Jan 1, 2010

By A. Spathis, I. Yacob, A. Labriola, G. Smith

Wall control is a significant issue for many mines. Improvements to the design process for blasts adjacent to temporary or final walls will require better measurement tools and predictive models. Orica Explosives has developed capability in both these areas and uses them to guide better wall control blasting practices. Vibration and gas pressure were monitored behind a series of production blasts and single hole blasts at the Freeport Grasberg Operations Opencut Mine. The blasts used ANFO in both 3 11 mm and 35 1 mm blastholes in a blast design which reduced the charge weight by between 30 to 50% in the final row of the production blasts. Single hole blast data were obtained by delaying the last hole in the production blast. Vibration levels were within the range often associated with vibration induced damage: 178 to 1080 mm/s at distances between 14-75 metres from the blast.

Jan 1, 2001

By Carl Lubbe, Ron Frye

Numerous articles have been written regarding the effects of blast control plugs in an attempt to quantify stemming ejection rates, air overpressures, fragmentation’and other parameters measured using these devices. In an effort to further attempt to understand the function of these devices, field and laboratory research conducted with various stemming devices was performed to enhance existing data sets and analyze otherphenomena that occur when these products are used.

Jan 1, 1998

By Roberto Folchi, Hans Wallin, Mara Battocchio

An understanding of explosives science and technology, and the competence to harness it is central to maintaining Explosives capability, national security, and in sustaining a competitive industry. A consequence of eroding this competence is the increased likelihood of explosives accidents. These are often catastrophic as demonstrated by accidents in Nigeria, Russia, Toulouse and Enschede. In addition to the serious loss of life there was the very significant damage to houses, domestic and industrial infrastructure and to the environment at a cost of many millions of Euros.

Jan 1, 2013

By Alexandra Yuyali

The objective of this research work is to increase the drilling ratio represented in tons per drilled meter (ton/m) to reduce mining costs. One of the key characteristics of this research is the use of the ITH (in-the-hole) drilling rig with a water-powered hammer, also known as Wassara™. The patented Wassara™ in-the-hole hammer is powered by high-pressure water instead of air. To reach the objective, a new design of the blast pattern was implemented considering the following: Burden from 1.7 m (5.6 ft) to 2.8 m (9.2 ft) Spacing from 1.7 m (5.6 ft) to 2.7 m (8.9 ft) Drill diameter from 89 mm (3.5”) to 102 mm (4”) Drilling length from 15 m (49 ft) to 30 m (98 ft) Borehole deviation < 2% The result of this new design is the optimization of the drilling ratio (ton/m); having as a baseline 5.2 ton/m with traditional equipment and obtaining 13.7 ton/m with the ITH drilling, which generates annual savings of $2.43M.

Jan 21, 2025

By Robert Martin, Brian W. Stump

As part of a series of seismic experiments designed to improve the understanding of the impact of mining blasts on verifying a Comprehensive Test Ban Treaty, a sixteen station network of three-component seismic sensors were deployed around a large cast shot in the Black Thunder Mine. The seismic stations were placed, where possible, at a range of 2.5 kilometers with a constant inter-station spacing of 22.5 degrees. All of the data were recorded with the seismometers oriented such that the radial component pointed to the middle point of the approximately 2 kilometer long shot. High quality data were recorded at each station. Data were scaled to a range of 2.5 kilometers and the sum of the absolute value of the vertical, radial, and transverse channels computed. These observations were used to construct radiation patterns of the seismic energy propagating from the cast shot. It is obvious that cast shots do not radiate seismic energy isotropically. Most of the vertical motion occurs behind the highwall while radial and transverse components of motion are enhanced in directions parallel to the highwall.

Jan 1, 1997

By Mark S. Stagg, Steven V. Crum, Stephen A. Rholl

As part of its ongoing research concerning rock fragmentation by blasting, the Bureau of Mines has undertaken a series of test blasts where six cylinder-shaped pieces of granite rock were fragmented using high explosives. The tests were intended to: 1) Establish a dataset that could be used in the development and verification of theoretical models that simulate rock blasting and 2) To add to the fragmentation data currently being collected by Bureau researchers. The cylindrical geometry was chosen so that the fragmentation could be directly compared to two-dimensional computer simulations that assume an axisymmetric configuration as well as more sophisticated three-dimensional models. The granite cylinders, Carnelian granite and Charcoal granite, ranged in size from about 0.46 meters (18 inches) to 0.58 meters (23 inches) in diameter by 0.91 meters (36 inches) to 1.52 meters (60 inches) in length. Physical rock properties tests performed on the Charcoal granite cylinders indicated that the rocks did in fact have similar physical characteristics. PETN-based detonating cord and dynamite were used as the explosive charges and estimates of the values of some important physical properties are given. For the first five tests, the blasted rock was contained by a heavy rope mat suspended inside the Twin Cities Research Center's blasting shelter. The fragments from each of these shots were sorted and weighed to determine the corresponding fragment-size distributions. Even though different types of granite and cylinder sizes were used, similar fragment distributions were produced from shots that used a similar explosive, in this case the PETN-based detonating cord, and comparable burden-to-charge diameter ratios. Significantly coarser fragmentation was produced from a blast that used dynamite as the explosive charge. Fragment velocities were calculated using photographic data from the sixth test which was shot unrestrained in a quarry and filmed with high-speed cameras.

Jan 1, 1990

By Benedicto Hadad Cintra

In an inflationary environment the need for reduced cost is a daily concern of all industries. The Du Pont do Brasil "Expanded Pattern" method has proven to be an extremely effective means of reducing costs in mining, quarrying and construction operations. Over the past years much emphasis was placed on rectangular drilling patterns where the burdens are less than the spacing. The Expanded Pattern method combining rectangular and staggered patterns, was implemented in 1971 in Brazil after extensive trials in close collaboration with numerous explosives users and Du Pont do Brasil Technical Services Engineers. The best multiple row spacing-to-burden ratio (S/B) was demonstrated to be in the 2 to 5 range and the effective spacing to burden ratio (Se/Be) was found to vary from 5 to 11. These ratios are for the interior of the blast pattern and do not hold true along the front row of holes. Geological rock properties, hole diameter and inclination, explosives energy and loading density, explosives characteristics, blast pattern geometry, bench height and delay patterns along with type and size of digging, hauling and crushing equipment must all be evaluated for each and every operation. The integration of these interrelated parameters, together with sound blasting practices are the basis for the Expanded Pattern method. Color slides and documented case histories will be presented.

Jan 1, 1985

By Christopher Jon Preston, Troy Williams, Daniel Roy

There has been significant progress made with narrow vein gold mines in which a second option for crushing has begun to attract attention. To ensure the profitability of a mine that has based its economics on the absence of a crusher station, more than just best blasting practices are required. Using a blasting operation itself as a primary crusher would undoubtedly save enormous capital costs as well as eliminate some of the costs of crushing ore with the result that considerable savings might be realized. The challenge would be to define the conditions necessary to make this type of operation feasible by providing consistent blasting methods that result in a significant paradigm shift with respect to both blasting and current underground crushing methods. A break model has been developed and applied as a technique in designing blasting patterns based on a unit charge blasting geometry and stress reflection from free faces. There are four components to this model and these are 1) unit charge, 2) thermodynamic/energy, 3) stress reflection, and 4) radial break. Some important changes in timing between holes and rows based on rock properties and the percentage of burden moved were also used. On-site testing at a narrow vein gold mine in Quebec Canada, provided measured parameters for the model. No underground crusher was planned - relying only on the fragmentation profile generated by ring blasting. The specification for muck was that the fragmentation profile needed to be 100% < 400 mm (16 in) with no overbreak - with dilution less

Jan 1, 2019

By Scott G. Giltner, Paul N. Worsey

During the short duration of an explosive blast, many events occur which are too quick to be detected or observed in detail with the naked eye or by normal photographic techniques. Through the use of "hightech", high speed video, many of these events can be observed, instantly played back and recorded for later use. The use of a Spin Physics SP 2000 Motion Analysis System at a blast casting operation is presented. The variable range of recording speeds offered by the SP 2000 allowed it to be used for examination of different areas of blasts. At its maximum full frame rate of 2000 frames per second the SP 2000 can easily pick up the flame front as it travels down a nonel tube and the flash from the surface delays as they fire. The system was used for a variety of tasks including, but not limited to,the determination of delay accuracy to within 0.5 ms, the velocity and trajectory of the faces during blasts, and pinpointing geological problem areas. The effectiveness of the system as used on site is discussed along with detailed method of set up, recording, playback and data processing. Other details including site specific environmental and lighting problems are also covered.

Jan 1, 1986

By John Brulia

You’ve probably heard the old expression, “The more things change, the more they stay the same.” But the adage doesn’t seem to hold much water when it comes to making a telephone call on the road. Thirty years ago, a “powder hound” had to stop his 2-wheel drive vehicle at either a roadside diner or a telephone booth to make a call using a public telephone. But, fast-forward to 2007, and a contemporary “explosives engineer” driving his or her 4-wheel drive vehicle simply makes a call “on-the-fly.” The fundamental difference between these two eras is the result of the introduction and the proliferation of cellular or wireless technology. On the one hand, this fundamental difference is much welcomed in the form of personal and business conveniences; and improved productivity. On the other hand, this fundamental difference creates a new set of un-welcomed conditions causing a potential “digital danger.”

Jan 1, 2008

By Randall M. Wheeler

Using Computer software to analyze and interpret blast vibration effects has never been so practical. Fully digital seismographs and powerful desktop and portable computers have led to the development of fast and easy to use analysis software. This workshop will focus on new Microsoft Windows-based blast vibration analysis programs developed by White Industrial Seismology, Inc. The Windows point and click graphical environment is ideal for developing full-featured and yet intuitive software.

Jan 1, 1994

By P D. Katsabanis

According to Persson(1) steady state detonation along a cylindrical charge can be regarded as a self propagating process in which the axial compressive effect of the shock front discontinuity changes the state of the explosive so that exothermic reaction sets in with the requisite velocity.

Jan 1, 1989

By John Cowin, Dan McCutchen

Cowin & Company has specialized in underground construction since 1924. This paper reviews the sinking of two shafts in the Alabama coal fields using bulk-loaded explosives. Each shaft is eighteen hundred feet deep, and their diameters were twenty feet and twenty-three feet. The first consideration in changing to a new explosives system was safety. Safety began with the explosive supplier training the miners in the use of the new system, from explanation of the pumping unit on the surface to hands-on training in the shaft. The considerations covered include establishing a thunderstorm exit plan, and reducing exposure time of the crew to explosives while loading. The system consisted of a specialized pumping unit and an advance emulsion product. Eliminating the need for nitroglycerin based explosives, and reducing sensitivity to mechanical shock were goals that were met. Performance in the shaft and ease of use meant morale of the miners using the system remained high and positive. Performance benefits discussed include reducing the number of holes in the round, and cutting explosives loading time in half. Damage to the ribs of the shaft was greatly reduced, making it safer to work near the ribs on succeeding rounds. Cleaning the bottom before drilling the next round also showed marked improvement. The economics of the system became very apparent when cycle time saved was allocated against fixed cost of sinking these shafts.

Jan 1, 2000

By Thomas E. Lobb, Harry C. Verakis

Blasting is a primary means of extracting minerals and ores at surface mining operations. The domestic consumption of explosives and blasting agents during the year 2001 was about 5.25 billion pounds. Flyrock is always a major concern for the blaster. Flyrock from surface blasting operations has caused serious injury and death to employees and other persons. Injuries due to flyrock and the lack of blast area security accounted for over two-thirds of all blasting-related injuries in surface coal, metal, and nonmetal mines during the period 1978-2002. Selected accidents due to flyrock and lack of blast area security in surface mining are presented in this paper. Incidents related to construction blasting are also described. Techniques to mitigate blasting accidents are discussed. These include proper blast design, driller-blaster communication, inspection prior to loading and firing the blast, removing employees from the blast area, controlling access to the blast area, and using a blasting shelter. An experienced driller could detect potential problem areas such as voids, mud seams, incompetent rocks, and other irregularities by observing the progress of drilling. The drill log should include the details of any unusual or exceptional circumstances noticed during drilling. A blaster may need to alter the loading configuration to alleviate potential problems. Basic blast design is sometimes taken for granted and assumed to be proper for the conditions encountered, but one size does not fit all. It is known from the physics of blasting that the explosive energy takes the path of least resistance. The path of least resistance could generate flyrock, depending on the blast site conditions. A combination of ‘borehole tracking’ and ‘laser profiling’ can assist in improving the design of a blast. The blaster can use these tools to adjust borehole loading to match site conditions.

Jan 1, 2004

By Alastair Torrance, George Boucher

The authors were involved in the Trial Blast work at Chek Lap Kok, the site of the new Hong Kong Airport. As part of that work a series of computer programs including 3x30, QFRAG, DESIGNER and 3DMUCK was employed to predict various aspects of the trial blast programme. These aspects included fragmentation and muckpiie shape. This provided an excellent opportunity for these programs to be calibrated, verified and compared under controlled conditions. The results indicated that computer simulation has reached a high level of sophistication and good correlation between prediction and measured results was found.

Jan 1, 1994

By Alastair C. Torrance

"A brief review of the Australian mining industry is given followed by a more detailed treatment of a study of the influence of primer Size on explosive performance. This is based on a joint research programme conducted by BHP Central Research Laboratories and Dyno Wesfarmers Ltd and examined the effect of the size of cast primers on the run up and steady state detonation velocitiesof ammonium nitrate based explosives as a function of blasthole diameter. The field trials examined a numter of the Dynamo 'Westfarmers HDF series of primers in conjunction with ANFO, emulsion and watergel explosives. Results indicate that the iun up velocity of 187 mm diameter ANFO charges is negligible using cast primers as small as 150g. However, emulsion and watergel explosives did exhibit run up in both 187 and 3:1mm diameter blastholes, independent of the size of primer. This could last from 7 to 10 blashole diameters"

Jan 1, 1991

By Harry Verakis

Flyrock is the second leading cause of all blasting related injuries in surface coal, metal and nonmetal mining operations. It is also a primary cause of property damage, monetary losses and “near misses.” For the period 1978 to 2008 flyrock accounted for 11.6 percent of all blasting-related injuries in surface coal, metal, and nonmetal mines. A large amount of published material has been published on the safety hazard of flyrock, on ways to predict how far rock will travel from a blast, as well as ways to protect mine personnel and neighbors from flyrock. However, flyrock incidents continue to occur resulting in fatalities and “near misses” that could have caused fatalities. It was only good fortune in some instances that no one was in the mine's parking lot or other unprotected area when flyrock rained down or in harm’s way when a large rock punched a hole in the roof of a building or other structure.

Jan 1, 2011

By Hae-Moon Choi, Sang-Don Lee, Hee Soon Shin, Choon Sunwo, Chang-Ha Ryu, Hyun-Koo Lee

Building tunnels means dealing with what rock is encountered. Relocation of the site of the underground structure is rarely possible. Tunneling engineers and miners have to cope with the quality of the rock mass as it is. Different tunneling philosophies and different rock classification methods have been developed in various countries. Most of the rock classification methods are based on the response of the rock mass to the excavation. Tunnel support requirements could be assessed analytically, supplemented by rock mass classification predictions, and verified by measurements during construction. Rock mass classifications on their own should only be used for preliminary, planning purposes and not for final tunnel support. Design of blast pattern in tunneling projects in Korea is also for the most part prepared according to the general rock classification methods such as RMR or Q. It, however, does not take into account the blast performance, and as a consequence, produce poor blasting results. In this paper, the methods of general rock classification and blast design for tunnel excavation in Korea are reviewed, and efforts to develop a new classification method, reflecting the blasting performance, are presented. Copyright ©

Jan 1, 2004

By Adam Stremcha, John MacGregor

Initial planning called for 3 separate drop shafts and 3 separate vent shafts to be pulled back from the excavated tunnel with a large diameter raise bore machine. With time constraints and the raise bore machine already in high demand on other shafts, a more “traditional” drill and blast approach was taken on a few of the larger drop shafts. This decision proved to be not only cost effective, but also reduced schedule impact as the shafts were excavated simultaneously with the other raise bores.

Jan 1, 2010