Search Documents

By Conny Postupack, Jim Petrunyak, John Loope

The authors discuss the concepts, engineering considerations, and cost relationships involved in the use of drilling and blasting to accomplish backfilling and reclamation with minimum use of mechanical equipment. The four methods of reclamation now in use are reviewed, and their advantages and disadvantages are noted. Guidelines for selecting a particular method are offered in terms of applicability under varying geologic, economic, and technological conditions.

Jan 1, 1987

By Joshua Micah Hoffman, Jhon Silva-Castro, Kylie Larson-Robl

A coal mine impoundment failure has the potential to be environmentally devastating and life-threatening. It is well documented that after seismic events slope failures in impoundments can occur. It has been concluded that often the main driven factor of the failure is the increase in excess pore pressure due to ground vibration. A small amount of research has been done regarding the stability of coal mine impoundments under natural seismic events; however no research has been done considering vibrations from mine blasts. If it is taken into account that current environmental restrictions oblige to increase the capacity of coal mine impoundments, thus increasing the hazard of such structures, it is necessary to evaluate the effects of near-by mine blasting on the stability of the coal mine impoundments in order to mitigate and control the potential of slope failures. To study the behavior of excess pore pressure under blasting conditions, scaled simulations of production blasting events were set up inside of a controlled sand tank. The research was divided in two stages. The first one was done, using dry conditions, while in the second part, the same set of tests were performed under saturated conditions. This document shows the partial results for stage one (dry conditions). For the tests, explosive charges were set off within the sand tank at various distances to simulate different blasting distances. Information was collected from geophones, accelerometers, microphones and high speed video camera for dry and saturated scenarios and additionally from piezometers under saturated conditions to assess the behavior of the material under blasting conditions.

Jan 1, 2015

By Changa-Ha Ryu, Hae-Moon Choi, Sang-Don Lee

The rock mass to be excavated is classified using data obtained from the initial site investigation, and the design of excavation and support is then made based on the rock class. Rock classification provides an empirical design with guidelines for tunnel support compatible with rock mass quality and the method of excavation. Although most clients provide standard patterns corresponding to each rock class, the patterns of drilling and blasting have only been used in estimating the excavation cost and not used in the construction stage. The purpose of the study presented in this paper is to establish a standard blast pattern to yield optimum blasting performance along with an attempt to reduce a difference between design and construction. A series of test blasts were carried out at two tunneling sites of Central Inland Highway crossing the country. Long hole blasting was tested in rock mass whose RMR value is over 60. The blasting results were evaluated by measuring degree of fragmentation, advance rate, muckpile distribution, overbreak, etc. Based on the results of test blast, several patterns were proposed for a twolane highway tunnel.

Jan 1, 2005

By Sharkey Bowers

This study was undertaken in order to determine a conservative estimate of the attenuation rate of vibrations through the shallow limestone in South Florida due quarry blasting. The natural limestone bedrock in occurs at or near the surface in southeastern peninsular Florida. While the shallow overburden soils is advantageous for mining purposes, vibrations from blasting has been a contentious issue in South Florida due to the proximity of the mines to several residential communities. White Rock Quarries and Krome Quarries are two active mining facilities in South Florida which generate numerous complaints, insurance claims, and lawsuits from residents in nearby communities who claim that the vibrations cause damage to their houses. Both quarries are located on the eastern edge of the Everglades, with thousands of nearby residences at the western edge of development in Broward and Miami-Dade Counties. Data obtained from over 400 publicly available blast monitoring and associated seismograph reports from White Rock Quarries were reviewed and compiled. The data was used to emperically develop a conservative estimate of the ground attenuation rate based on the scaled distance from the blast origin, which can be compared to Figure B-1 from USBM RI 8507 to determine whether it is feasible if damage could have occurred at a given property.

The use of angled shot holes can be extremely effective in blasting faces that either have a great deal of toe burden or where it is difficult to give a drill access to a face due to backbreak and face erosion. However many quarry operators are wary of using angled holes because of the perceived possibility of increased flyrock and uncertainty of the driller's abilities to drill at the designed angle.

Jan 1, 1994

By Roy Rose, Bruce Bowles, Wesley L. Bender

Numerous large diameter water wells are used to dewater the pit at the Sleeper Mine. Occasionally, a well will be located inside the boundaries of a blast. Although one might expect that wells so located would become inoperable due to blast-induced damage, in most instances this has not proven to be the case.

Jan 1, 1991

By Sandra K. Penttinen

A difficult blasting project can go very smoothly when every precaution is taken prior to and during the blasting procedures. These precautions include conducting careful preblast condition surveys of nearby structures, initiating a good public relations program prior to the beginning of the blasting, and following a good safety program during the blasting procedure.

Jan 1, 1994

By Joshua Micah Hoffman, Catherine E. Johnson

The recruitment and retention of future talent into the explosives industry is becoming increasingly important. One potential area from which future talent can be recruited is local student chapters. Many of the student chapters are closely connected with engineering programs. While this makes sense and both entities benefit from these arrangements, there is a trend of job placement primarily in the engineering industry. Before the explosives industry can begin to compete with other industries, it should be determined what is drawing the students into these other fields. The work presented in this paper sought to better understand the collegiate student population from which a portion of future explosives professionals will emerge. This was done through the use of an anonymous online survey distributed to the student members of the International Society of Explosives Engineers, as well as, members of SEE student chapters. The survey contained questions about future job and career plans, ideal job placement, and expectations of salary. The purpose of the survey was to determine what these students expect or require from a career in the explosives industry. This information can help steer recruitment activities and job offers. Through understanding what is incentivizing these students who have accepted or plan to accept jobs in other industries the explosives industry can better posture itself to be more competitive in recruiting from the collegiate talent pool.

Jan 1, 2014

By J. -P. Tshibangu, E. Lefebvre

ABSTRACT : The Tournai’s region in Belgium is characterized by outcrops of limestone that were mined out long ago by different companies for cement and crushed materials. The region is densely populated and the vibrations generated by blasts in the quarries are of big concern. The occurrence of electronic detonators and development of computer sciences brought a new expectation in controlling the vibration level and, hence, carry out bigger blast operations. In this paper we present the results of two experimental blast programs that have been carried out by the Nobel explosive Belgium Company on the Gaurain-Ramecroix quarry to understand the effect of the delay on the vibrations generated in the neighborhood. The first program has been implemented during the early use of electronic caps in Belgium (1996) by performing some unit shots. An attempt to model the effect of the production blasts by the hybrid method (Hinzen 1988) gave promising but poor results compared to infield measurements. A new program (more than ten blasts) has been implemented in 2006 in which the delay and blast firing sequence (i.e. the order in firing adjacent holes in a row) have been changed; a new attempt is made to build unit signals by deconvolution and then try to model production ones. A comparison of the two approaches is made.

Jan 1, 2008

By C. Rutledge

The new mining method of multiple strata blasting, called StratablastTM, is described in a separate paper presented at this conference. The current paper presents three case studies where the technique was implemented in three different configurations in large-scale blasts in Australia. The first two blasts were in the Hunter Valley of NSW while the third was at Ensham Mine in Central Queensland. All blasts comprised multiple layers that were blasted in a single drill and blast cycle, with unique designs applied to each layer to achieve different blast outcomes from the various layers.

Jan 1, 2006

By Ray Jambakhsh, Craig Copping

The St. Lawrence Seaway's Welland Canal has been undergoing a rehabilitation program that requires the removal of deteriorated concrete from the 25 meter high lock walls. Multi million dollar contracts must be completed during the three month winter freeze up. New blast designs have drastically cut the time required for concrete demolition. All blast results including vibration, noise, underbreak, overbreak, scaling and flyrock have been improved and at a lower cost.

Jan 1, 1994

By Ronald W. Roberts

For years, blasters have experienced near-misses, injuries, and yes, even fatalities as a result of the dangerous nature of our business. Yet, some blasters continue to portray the immortal attitude: nothing-would-or-could-ever-happened-to me syndrome. As we all know, that attitude can become disastrous to yourself or colleague(s).

Jan 1, 1996

By Gary Anderson, J. P. Remi Proulx

Rio Tinto’s Colowyo Coal Mine produces 2.1 million tons per year in northwest Colorado. Colowyo uses the terrace mining method to recover up to seven coal seams ranging in thickness from 5 to 20 feet. Coal recovery in the 6 foot thick high grade C-seam has recently been challenged due to large variations in the pitch and roll of the seam. As well, some coal damage was seen due to an increased thickness of the overburden consisting of a hard sandstone channel.

Jan 1, 2012

By Sarma Kanchibotla

In mineral industry operations the insitu ore is’separated from the waste rock and is subjected to a series ofprocesses to convert it into a valuable product. Profitability of any operation in this industry depends on how eficiently the insitu rock (ore -I- waste) is converted in to the final product and how much value @ice) it commands in the market. Traditionally, the total process in mineral industry is classt@ed into two groups as mining and milling, and optimised independently without considering the impact of one over the other. This paper investigates the impact of mining operations (especially blasting;) on downstream processes and demonstrates the potential benefits of the “Mine - Mill Blasting” approach through simulations and case histories.

Jan 1, 2000

By Rob Farnfield, Ben Williams, Ashley Haslett, Diane Cartledge

Major accidents that occur within our industry are often tragic and expensive, damaging reputation and threaten the livelihood of the business. There isn’t anything in them that can be seen as positive for those that experience them. They undertake what are usually very painful, detailed and time consuming investigations to discover how the incident occurred and what needs to be done in the future to prevent similar incidents occurring. Many admirably choose to share the lessons learnt through industry organizations such as SAFEX International so that we can all have the opportunity of preventing similar incidents from occurring within our own organizations.

Jan 1, 2016

By Gerald G. Schmitt, Richard D. Dick

Continuous Reflectometry for Radius vs Time Experiments (CORRTEX) was used to monitor several conditions of blasts such as the detonation velocity of the explosive column, the functioning of different types of initiators and initiation schemes, and the behavior of the stemming column confining the explosive. The CORRTEX data were also used to deduce the occurrence of dead pressing of ANFO slurry. Measurements of propagation speeds of shock waves in the stem column with various cables allowed some conclusions concerning bridging, stem failure, and stress levels in the stem.

Jan 1, 1985

By Kunihisa Katsuyama, Yuji Ogata, Yuji Wada

The one free surface blasting of a concrete block was simulated by Discontinuous Deformation Analysis(DDA) method. Comparing the simulated results with the concrete block blasting experiment, the crack growth and the free surface displacement which were simulated by DDA were observed with a high speed camera.

Jan 1, 1996

By Finn Ouchterlony

"Recently detailed fragmentation data from blasts fired with electronic delay detonators (EDDs) in the Red Dog mine in Alaska were presented. They include a comparison with pyrotechnic detonators fordifferent in-­-row delays in a standard pattern and EDDs in an expanded pattern. Fragmentation was measured on the belt after the primary crusher. The Rosin-­-Rammler function (RR, two parameters) was used to describe the crusher product. This was combined with the JK SimMet crusher model and the CZM blast model (Crushed Zone Model, three to five parameters) to estimate a reasonable crusher feed (muck pile fragmentation or run of mine, ROM) for each fitted product. In this way the effect of delay timing and electronic detonators on the median fragment size x50 and uniformity coefficient n for both crusher product and the blasted rock was determined. "

Jan 1, 2012

By Cathy McGinley, John Mullay, Clark Stancavage

The use of crater studies to evaluate explosive performance is a well-established practice in the Blasting Industry. Normally, this work utilizes larger charge sizes (>75mm) in order to minimize the influence of geological factors adjacent to the borehole. This can impose unwanted restrictions in the experimental factors accessible to investigation. Thus, for example, systematic studies of non-ideal performance in a somewhat practical setting is rendered quite difficult.

Jan 1, 1995

By Kenneth Faroni, Catherine Aimone-Martin, Thomas Gelormino

A blasting improvement program began in 1985 at two traprock quarries in Connecticut to reduce the levels of ground motions and airblast measured at residential structures surrounding the operations. The quarries are situated within town limits, adjacent to a number of historical and other structures. Although blasting vibration amplitudes were found to be far below those that could produce cosmetic defects in structures, they were perceived to be the cause of structural defects observed by homeowners. Based on a comprehensive * review of blasting practices in place during1985, an extensive vibration monitoring program was implemented. The initial study included the instrumentation of selected residential structures to record and analyze strains imposed within structures from quarry blasting, environmental changes, and from daily household activities. A comparison of the results was made with the results reported by the U.S. Bureau of Mines in 1980. The highest strain imposed in drywall from blasting (13 J_I strain) was 12% and 1% of the highest strain levels recorded for normal household activities and temperature changes, respectively. The present philosophy in production blasting is to attempt to keep vibration amplitudes as low as practical by implementing state-of-art blasting control techniques. Currently, blasting seismographs are placed in a circular manner around each quarry, providing production blast vibration records for 360 degrees of coverage at distances of 2500 to 4000 ft. from blasting operations. Seismograph and production blast records are analyzed each year and become part of a Blasting Improvement Plan submitted to the local zoning commission as part of the annual operating permit process. This paper summarizes the results of previous vibration monitoring programs and outlines the modifications made to blasting practices to minimize the levels of ground motions and airblasts. The public relations efforts and standard corporate procedures used by company personnel to address all blast related complaints and alleged damage claims since 1985 are also discussed.

Jan 1, 2000