Search Documents

By Stephan Iversan, Janae Singer

High resolution seismic refraction tomography has proved to be a useful tool to effectively estimate depth of blast induced damage in rock. Excavation blast damage can be as shallow as 1 to 2m (3 to 7ft) and requires resolution at a fraction of a meter for effective imaging. We used an accelerometer with flat frequency response to 1000Hz to record data at spacings of approximately 0.25 to 0.5m (0.8 to 1.6ft) along mine walls. The resulting tomograms of P-wave velocity show low velocity zones which we interpret as residual fracturing from blasting. Experiments on a concrete test block and at two underground mine locations give results that are consistent with fractured rock transitioning to competent rock.

Jan 1, 2009

By K Ramachandra Rao

Joints, fractures and other structural defects bring anisotropic character Into a rock mass. Conventional methods of blast design In a rock mass consisting phyllites, mica schist etc., which are characterised by the presence of closely spaced, nearly vertical planar Joints, result In formation of large slabs which cannot be handled by the excavation and loading equipment without resorting to secondary blasting. Frequent secondary blasting Is not only expensive but also, Is a source of environmental hazard. Interruption of production cycles frequently, leads to uneconomical mining. This problem could be minimised by designing blasts which produce forces whose components along and across the joints/fracture planes Is lust sufficient to break the rock mass In both directions. Rock mass strength can be assessed from field and Laboratory tests. Projecting structural features with respect to bench orientation on a stereoplot helps In assessing magnitude and direction of force vectors required to fragment the rock mass to the desired size range.

Jan 1, 1995

By David E. Siskind

"This report describes recommended vibration monitoring and assessment practices at blasting sites.Intended is regular monitoring, tracking of trends, responding to complaints of alleged damage, and the technical and data aspects of addressing lawsuits."

Jan 1, 1999

By TH Kleine, AR Cameron

Size assessment of fragmentation is all about estimating the population of fragment sizes in the rock pile. A knowledge of the size distribution of particles can be used in applications from evaluating the stability of a waste dump, to optimizing a blast design to achieve a required fragmentation, to on-line control of a crushing and sieving operation.

Jan 1, 1997

By Split Engineering Chile Fernando Fernandez

Mathematical modeling in conjunction with mineral characterization is widely used as a method for design and optimization of comminution circuits, to simulate the processes of crushing, grinding and classification. An important input parameter to the simulation models is the Run-of-Mine Particle Size Distribution (ROM PSD). The run-of-mine size distributions due to blasting have a great influence on the performance of a semi-autogenous grinding (SAG) mill. In this paper, a mine case study was conducted where there are four primary geologic units and the material properties between the four units vary considerably. Also, the mixture of the four unit that will be mined at any given time also vary considerably. This presents a challenge in terms of optimizing the blasting for mill production throughout the mine life. As part of the case study, field rock mass characterization, laboratory rock mechanics tests, and laboratory breakage tests were conducted. The field characterization and rock mechanics tests provide material properties used to simulate the effect of different blast designs on run of mine particle size distributions (ROM PSD). The JKSimBlast software was used for these simulations. The rock breakage tests provide material properties used to simulate crushing and grinding performance. The JKSimMet software was used for these simulations.

Jan 1, 2015

By Carlos Agreda

A general review of the comminution theory and also the general differential equation of the comminution are described, analyzed and discussed in order to be applied to rock blasting. Some size distribution functions are reviewed and discussed to determine which of them represents better the cumulative low size distribution F(x) as a function of the nominal particle size (x), for the rock blasting fragmentation. Based on the mathematical comminution model before presented a formula to calculate the burden (B) is developed and discussed.

Jan 1, 1994

By Valerie A. Rhodes, Catherine T. Aimone

Often blast damage litigation involves structural damage which clearly is not blast related. The fact that structures are observed to be damaged when blasting has taken place in the near vicinity of these structures does not necessarily mean that the damage was caused by blasting. If careful blasting and seismograph records were kept by the blaster which decisively indicate damage is not blast related, then other causes of structural damage need to be assessed. These include problematic soil characteristics and long-term changes in climate or subsurface soil moisture. This paper presents the evaluation process required to investigate soil problems leading to damage often attributed to blasting.

Jan 1, 1991

By Huang Fenglei, Jin Qiankun

A new linear charge method has been applied in coyote blasting for highway excavation in which presplitting boreholes are set along the designed rock slope with some empty chambers at the end of linear charges whose axes are perpendicular to the axis of the highway. Three-dimensional nonlinear finite element analysis for this method has been conducted using LS-DYNA3D. The results indicate that the blasting damage to the rock slope is reduced greatly using the new linear charge method in coyote blasting.

Jan 1, 1998

By Dale S. Preece, J Paul Tidman, Stephen H. Chung

A discrete element computer program named DMC_BLAST (Distinct Motion Code) has been under development since 1987 for modeling rock blasting (Preece & Taylor, 1989). This program employs explicit time integration and uses spherical or cylindrical elements that are represented as circles in 2-D. DMC_BLAST calculations compare favorably with data from actual bench blasts (Preece et al, 1993).

Jan 1, 1997

By ISEE

Micrometer Crack Response to Vibration and Weather, by Prof. Charles H. Dowding of Northwestern University, adds to Prof. Dowding’s already important contributions to the industry with his “Construction Vibrations” books. This new book reports and interprets important data on crack response that are essential for differentiating the unseen effect of weather on structural cracking from the usually much smaller effect of vibration. In addition, the book contains detailed descriptions of data collection methodology.

Jan 1, 2010

By Tom Hale

Developers and blasters are faced with increasing public demand and regulatory restrictions to maintain the lowest possible levels of noise and vibration from blasting operations in populated urban areas. Pyrotechnic products have proven to be a low noise, low vibration alternative to conventional blasting for close-in rock excavation and concrete demolition applications. Pyrotechnic breaking charges often yield 1/10th the vibration and noise compared to traditional explosives, and have been demonstrated to increase public confidence and decreased damage potential where they have replaced explosives, thus allowing new opportunities for work and greater job profitability. This paper presents a practical approach to utilizing pyrotechnic products in various applications including trenching, mass excavation, demolition, and dimension stone production, providing methodology for pattern design, vibration probability and loading calculations. Field research data is reviewed and compared to conventional explosives.

Jan 1, 2008

By Gordon Revey

In construction and mining work, situations occasionally occur where hard rock or concrete must be excavated at locations near critical structures or utilities. Fearing damage from blasting, contractors and engineers often explore the viability of using mechanical methods or expansive concrete to facilitate the excavation work. However, for moderate to large excavations, the prolonged duration and high cost of using these methods is often impractical. In these situations, under the right conditions, controlled blasting and blast-management methods can be used to speed up the work and lessen costs. The process of determining whether or not blasting is practical is ofien complex, particularly when risks are high.

Jan 1, 2001

By Michael S. Wieland

Underground coal-mine explosives (permissibles) can be substantially degraded by the underground stress waves from the explosion of neighboring borehole charges. This cross-borehole interaction generally yields the worst receptor (impacted) charge performance when the borehole separations are too close. For explosives which recover, the receptor degradation is worst when the delay until firing is small. Except for a poor quality muck pile or unreacted cartridge fragments, degraded charge malfunctions of this type are difficult to detect in coal-mine delay blasting. A simulator which reproduces the underground wave/receptor charge interaction and special underwater donor/receptor tests were utilized to study this transient desensitization problem. Test results revealed reductions in receptor energy output, delayed transitions into detonation, inferior reaction rates, or sympathetic reaction responses from the impaction. Tests on detonators showed reduced tip-strength, abnormal functioning times, or sympathetic firing as a result of transient impaction. The cross-borehole desensitization and sympathetic reaction response problems warrant concern because they are logical mechanisms for raising the risk of hazardous mining conditions, including blown-out shots, flyrock, charge deflagration, and methane/coal dust ignitions.

Jan 1, 1987

Current research in comminution includes efforts to increase the efficiency of mineral processing systems and reduce the amount of electrical energy needed for size reduction. In most mining operations, comminution begins with blasting. Normally, blast design focuses on loosening material for excavation and sizing the product for efficient haulage. It is likely that blasting also results in internal damage to rock fragments within the blast pattern which may provide subsequent comminution benefits. If substantial comminution benefits exist, appropriate modification to blast pattern design may reduce the overall electrical energy needed for mineral liberation.

Jan 1, 1996

By R D. Skaggs

A good blast is dependent on a well engineered design. However, a good design's performance depends on the control of the drilling and loading of the blast holes. The key stone to good blasting is the drilling of straight holes of the correct orientation in the required positions.

Jan 1, 1991

By Dale S. Preece, Stephen H. Chung

"A discrete element computer program named DMC_BLAST (Distinct Motion Code) has been underdevelopment since 1987 for modeling rock blasting (Preece & Taylor, 1989). This program employsexplicit time integration and uses spherical or cylindrical elements that are represented as circles in two dimensions (2-D). DMC_BLAST calculations compare favorably with data from actual bench blasts (Preece et al, 1993b)."

Jan 1, 1999

By Robert Cefalo

Drill and Blast Engineer Abstract In 2019, the Bingham Canyon Mine, owned by Rio Tinto Kennecott Utah Copper Company, mined through the active underground that dewaters the pit. The active underground required the limitation of vibrations to avoid catastrophic damage or damage that would require work to the shotcrete and additional roof support. The surface design of the current sector next to and through portions of the active underground. The drill and blast group was required to test site law vibration parameters to ensure that vibration limitations were lower than limits set by the underground management team. Seismographs were used to validate the vibration prediction model and check performance of blast in areas of the underground. The bench conditions and limited pounds-per-delay created large obstacles for the blasting team, making it difficult for them to accurately load the pattern with the number of decks in the blast. Methods were used to improve the loading instructions and ensure that each hole achieved pound requirements based off of the distance to the underground that it was designed to protect. The project evolved from start to finish, and the process to estimate distances and loading improved to make the blast a more repeatable process for the size of the project.

By John Brown

Let’s talk about things that you, the driIl boss, the pit boss and the driller can do to eliminate the trend in drilling related accidents that have come to plague our industry in recent years. My paper will focus on reaI issues, problems and solutions that will affect our everyday outlook and attitudes about our jobs and lives. There are some real hard facts we must address if we are going to reverse this terrible killing trend.

Jan 1, 2000

By Sergio Segovia Parra, Victor Hernan Sheen Uriol

This contribution of the concept of mass blasting both closing and production allows breaking paradigms, to limit the number of tons to thunder. The areas of geotechnical different mining large mining companies worldwide and especially from the National Copper Corporation (CODELCO, Chile) has been declining volumes closing blasting and production, with the misconception to protect the end walls of the pit, before any geotechnical risks caused by various types of faults; especially the circular faults. A blasting of small tonnage can do more damage to a wall when it is not properly sequenced, leading to the coupling of the wave train and therefore the exponential damage in/s (peak particle velocity, PPV) on the wall of the Tagus. Blasting closing mass production and contribute technically and operationally in the dynamics of the following operations: loading, hauling, crushing, processing and preparation of the final product; eliminating delays to return to thunder small volumes where one must stop all mine equipment, incurring high costs and especially losing valuable time in the continuity of the following unit activities.

Jan 1, 2015

By B T. Lusk, Jhon J. Silva

"The original signature hole technique to predict vibration levels from blasting, is based on theassumption that each hole in a production blast, generates an identical vibration waveformarriving to the point of interest. When the same waveform is used to represent the vibrationproduced by each hole, the complete waveform for the whole blast is the convolution betweenthe waveform and the impulse sequence that represents the initiation timing of the blast. In thisresearch, several field tests were developed to establish the validity of the invariability of thewaveform hole-to-hole in a mining production blast. The results of the tests showed that thereare variations in amplitude and frequency content for the hole-to-hole waveforms. Thevariations can be explained due to the character of the parameters involved in a production blastbetween them: different vibration path for each hole, differences in the geometry of each hole,differences in the explosive charge for each hole (chemical and quantity), etc. This paperdescribes a methodology based on the main characteristics in both; time and frequency domainof any recorded signature waveform and uses Fourier series to approach one equation to generatedifferent random waveforms for each hole that can be used in the prediction of the completevibration record of the blast. The methodology is the base for signature hole analysis using aMonte Carlo scheme."

Jan 1, 2012