Search Documents

By Carlos Agreda

"In the present article a case study of ammonium nitrate in mine water is briefly analized and discussed. Causes of mine water pollution from AN are very well identified and emphasized.Some preventative measures, as well as, some methods of monitoring and control to minimize, mitigate and/or avoid mine water pollution are recommended."

Jan 1, 1999

By R L. Keller

Hong Kong has some of the most restrictive practices regarding blasting than any place in the world. Regulations regarding vibration limitations are 1 in/sec for structures and 0.5 in/sec (or even less) for most utilities; with no recognition of frequency response or adjustment. The Hong Kong Geotechnical Engineering Office has one of the most conservative approaches and protective guidelines for pre-blast assessment of slopes subjected to blast vibration (SEE paper '96). The protective measures to control flyrock generally required by the Mines Division are additionally very stringent. It is not uncommon for the costs associated with protective measures or methods which must be employed to exceed the cost of the drilling and blasting itself - or to waiver blasting application unfeasible altogether. From these restrictions it can easily be imagined how blasting in this urban environment would be most challenging.

Jan 1, 1997

By Francis O. Otuonye

An application of a time series and systems analysis modeling technique to blast vibration data is discussed. The vibration data was taken from a rock support structure and the surrounding rock mass at distances close (less than 15 feet) to a blast. The analysis technique provides quantitative information on the frequencies of ground motion as well as the frequencies and damping ratios of a near-field support structure.

Jan 1, 1994

By T S. Bajpayee, Thomas C. Ruhe

"The Pittsburgh Research Laboratory of NIOSH conducted research to determine the safe operatingconditions for using recycled (used) lubricating oil from mining equipment as a partial replacement for diesel fuel to make ANFO-type blasting agents. The use of recycled oil (RO) conserves energy, reduces oil imports, and reduces mining costs."

Jan 1, 1999

By Mark S. Stagg, Stephen A. Rholl

As part of its research program to evaluate efficient design criteria for improved blast fragmentation, the Bureau of Mines has developed two computer programs to facilitate data analysis. Results of these two programs are used to better understand the fundamental parameters of blasting for surface mine rock fragmentation.

Jan 1, 1990

By Ettore Contestabile, Cameron Thomas

Implosive-type electrical/mechanical connectors such as XECONEX have been used extensively for joining electrical transmission lines. This implosive action of explosives has also been applied to other forms of high energy metal working with excellent results. However, as with many other products, the inherent blast energy of these units has caused some environmental concerns especially when used in proximity to inhabited areas.

Jan 1, 1995

By Ettore Contestabile, Cameron Thomas

Implosive-type electrical/mechanical connectors such as XECONEX have been used extensively for joining electrical transmission lines. This implosive action of explosives has also been applied to other forms of high energy metal working with excellent results. However, as with many other products, the inherent blast energy of these units has caused some environmental concerns especially when used in proximity to inhabited areas.

Jan 1, 1995

By Chantale Doucet, Yves Lizotte, Alan Cameron

A joint Federal Government-Industry research project on the effect of geology on the fragmentation of rock excavated by blasting in underground developments was conducted at the CANMET Experimental Mine, near Val d’Or, Quebec. A total of thirteen (13) blasts were studied from November 1994 to February 1995. The analysis of each blast was divided into three stages: pre-blast characterization, including structural mapping, assessment of Rock Mass Ratings (RMR), Tunneling Quality Indices (Q), blast design documentation; blast characterization comprising blast vibration monitoring and analysis; and post-blast assessment comprising fragmentation assessment by digital photoanalysis, calculation of half cast factors and measurements of bootlegs.

Jan 1, 1996

By Bruce B. Redpath

This paper reviews empirical and analytical information about window breakage due to airblast. As is the case with damage to structures caused by ground vibrations, a fixed break/no break threshold is inapplicable and window damage must be expressed in terms of a statistical probability. The information is summarized in a graph showing the probability of windows being broken by a given level of overpressure.

Jan 1, 1976

By Joel Warneke, Cristian Caceres, Ed Mchugh

NIOSH researchers collected basic data from two blast rounds at the SSX-Steer Mine as a component of a larger study on controlled blasting, the goal of which is to reduce injuries from falling rocks in underground mines. Drilling and blasting procedures at the mine were observed. Rock mass property data were collected, a program of seismic monitoring and analysis was conducted, and 3-D laser survey scans of the workings before and after each blast were performed. The geologic data showed that the rock mass quality was characterized as poor to very poor. It was essentially uniform within the panels examined. The recorded seismic data indicated that fill material acted as an effective damper to seismic energy. The pre- and post-blast laser scans showed both over-break and under-break conditions, highlighting the problems associated with blasting a weak rock mass. By comparing the achieved results to the intended design, potential improvements in the drilling and blasting practices can be identified. Comparison of these data with similar data from other mines will help define how various combinations of rock and fill behave during blasting. Through studies such as these, data collection procedures and analysis techniques can be refined. An ultimate goal is to develop blast procedures tied to rock mass characteristics that can minimize damage to rock in the perimeter of the opening, limiting the amount of loose rock and improving the safety of miners.

Jan 1, 2008

By John Horgan, Ethan Marcoux

Explosives have been used to demolish many unsafe structures around the world. However, it is unlikely any demolition job has ever involved destroying buildings already buried 40 feet (12 meters) into the world’s largest ice sheet. That is what happened to the original research station at the geographic South Pole, built back in the 1950s, following a series of discrete explosions between 2011 and 2013.

Jan 1, 2015

By Catherine T. Aimone-Martin, Susan G. Beattie

A series of small scale explosive tests were performed at a perlite mine near Socorro, New Mexico. The tests were designed to investigate the azimuthal or directional relationship between small scale geologic structures such as joints and the propagation of explosively-induced ground motions. Three shots were initiated within a single borehole located at ground zero at depths varying from 83 m (272 ft) to 10 m (32 ft). An array of three component velocity and acceleration transducers were placed in two concentric rings at distances of 20 m (66 ft) and 40 m (131 ft) surrounding the single hole at 7.5° , 15° , and 30° azimuths as measured from ground zero. Data from the transducers were then used to determine the average propagation velocity and waveform characteristics of the blast vibration through the rock mass at the various azimuths. The rock mass was mapped to determine the predominate joint orientations (strike and dip) and the average propagation velocities were correlated with this geologic information. The results showed that there is a correlation between the predominate joint orientation and ground motion amplitudes and velocity. The more predominate geologic structures allow the wave to follow along their strike thereby forming a planar path of least resistance and in turn, allowing higher velocities and amplitudes. Secondary joints or structures may act in concert with more prominent features to form a network of channels or paths along which the wave moves more freely than it may when traveling against the structures. The greatest azimuthal variations in velocity and amplitude was observed for the shallow shot at 10 m (32 ft) depth.

Jan 1, 1996

By Michael S. Wieland

Delay detonators that are damaged by cross-hole wave interactions degrade blasting work and raise the risk of incidents. Damaged detonators impose risk, because they can retain sensitive explosives that respond to stray energy during recovery, inspection or disposal. Laboratory techniques were developed to rank the ruggedness of delay detonators under replicated field-shooting conditions. The hazards are tremendously magnified if trial detonators are installed directly in secondary explosives to rank initiation strength. Therefore indirect ranking techniques were sought that mitigate the risks without compromising the worthiness of the method. Four types of hardware fixtures, referred to as simulators, were developed to yield distinct forms of transient compression. The shock and rift versions generate compression pulses representative of in situ waveform components. The waiting time, until the trial detonator functions, duplicates typical delay periods. The trial detonator is mounted within water, which has a density and inertial resistance comparable to most blasting explosives. The work output from the trial detonator explosion is registered as fixture wall-expansion. This work output determines malfunction results, regardless of which type of simulator is used.

Jan 1, 1997

By Dale S. Preece, Steven Knudsen

A discrete element computer program, DMC (Distinct Motion Code) was developed to simulate blast-induced rock motion. To simplify the complex task of entering material and explosive design parameters as well as bench configuration, a full-featured graphical interface has been developed. DMC is currently executed on both Sun SPARCstation 2 and Sun SPARCstation 10 platforms and routinely used to model bench and crater blasting problems.

Jan 1, 1994

By Michael McDougall

"Suncor Inc. Oilsands Group, Mining Operation in Northern Alberta, Canada, has beenblasting to loosen the oilsands to increase production and decrease maintenance of the hugebucketwheel excavators for over twenty years. In 1991 an area of the mine wasencountered which had a working face in excess of 130 feet. In order to maintain theproduction objective, the blasting department took on the task of providing as much of ablasted face to work with as possible. In doing this Suncor has exceeded several knownrecords in production blasting."

Jan 1, 1993

By Jonathan Heiner

Rio Tinto Bingham Canyon Mine started its South Wall Push Back (SPB) in 2011. This push back will mine through the only road to the pit bottom (the 10%). The pit bottom is the main ore sector for the mine and supplies about 80 to 90% of the ore. In late 2017 the mine set off a blast in SPB that created a small wedge failure on the high wall between SPB and the 10%. This wedge failure released a rock approximately 20 minutes after that blast that rolled down the wall landing on the 10% near and then contacting a light vehicle

Jan 1, 2019

By T Guiliani, F Ottuonye

Explosives casting is gaining increasing popularity as an overburden removal method in strip mining because the coats of using explosives to cast a percentage of the overburden to the spoil are lower than the costs of using stripping shovels or draglines to do all the overburden removal. This is due to the rising capital and operating costs of draglines and shovels.

Jan 1, 1989

By Kurt B. Oakes, Brian M. Fortelka

Unimin Corporation operates an underground Silica Sand mine at Guion, AR located in North Central Arkansas. The Silica Sand deposit at Guion is part of the St. Peter Sandstone Formation, which is overlain by a competent dolomitic limestone from the Joachim formation, acting as the roof directly above. Both the St. Peter and the Joachirn Formations are of Middle Ordovician age.

Jan 1, 1999

By John C. Adams, Robin Irwin

In early 1993 a test program was designed to determine if mining costs could be reduced by using a high density ammonium nitrate mini-prill blasting agent. The goal was to reduce mining costs by expanding blast hole patterns while maintaining or improving dig-ability of the shot material. The program was conducted at Santa Fe Pacific Gold's Lone Tree gold mine near Valmy, Nevada.

Jan 1, 1994

By Mark S. Stagg, Stephen A. Rholl

The firing times of millisecond-delayed initiators are random variables that exhibit varying degrees of scatter. This scatter can cause crowding and overlap of adjacent delay periods, which results in adverse effects on safety, fragmentation, and blasting vibrations.

Jan 1, 1988