Search Documents

By Atsuo Inoue, Toshihiro Ogata, Hideaki Sugihara

Generally in Japan, since ANFO has easy handling and low-price, it is most used as industrial explosives. However, ANFO is very easy to dissolve in water, it is difficult to use under existence of water and the consumer have desired water-resistant ANFO which has perfect water resistance. Then, we have developed the Water-Resistant Granular Explosive (It is written as following WRGE.) in which the surface of the explosive was covered by waterproof film, so that WRGE is able to use in hole with water. We ran various performance tests about the WRGE developed in the laboratory. Consequently, WRGE has water resistance of over 6 hours, and it has been checked that a performance and handleability were equivalent to the conventional ANFO. Then, we carried out the field test in the consumption site, and did performance evaluation on an on-site level. As compared with ANFO, fragmentation (size and volume) and handleability are almost equivalent. However, some problems which the WRGE is not settled out smoothly in hole with water and need more time for loading were also clarified. We are going to continue some advanced improvements through field tests.

Jan 1, 2005

By Lina Lopez, Jose Sanchidrian, Jean Du Mouza, Essaieb Hamdi

This paper evaluates the actual energy delivered by the explosives used in the fragmentation of rock during blasting vs. the available theoretical explosive energy. The evaluation of the fragmentation energy of the blast is first done. Fragmentation by blasting can be seen as a process in which creation of new surfaces within the rock mass is made by generation of new cracks or extension of pre-existing ones. From this idea, the fragmentation blast efficiency can be assessed as the fraction of the available explosive energy used for creation of new surfaces. The evaluation of new cracks area created by the blast is based on the SIMBLOC methodology and the corresponding fragmentation energy is then obtained by the Griffith theory. Secondly, the amount of energy delivered down to a certain pressure or volume along the detonation product expansion process, given by the useful work, is calculated. This is done by first determining the CJ state of the reacted explosive and subsequently performing an adiabatic expansion calculation of the detonation products from that state. W-Detcom code has been used for the calculations using the BKW equation of state with the Sandia parameter set. The fragmentation energy and the useful work are calculated for blasts performed in two mines in Spain. Multiple regression is applied to the results in order to give an assessment of the better description of the explosive energy .

Jan 1, 2002

By Satish R. Kate

Explosive is a chemical energy, which on detonation is released instantaneously with extremely high speed and under high pressure. It is used to meet the basic requirement for breaking of rocks. The productivity is the function of Drilling, Explosives and Fragmentation. Thus, the quality of explosives (energy content) is the key to get desired fragmentation. The variation in energy of explosives and volume of rock per hole have direct impact on fragmentation and cost of excavation (drilling and explosive costs). With the application of higher and higher energy content explosives, it is possible to expand the drilling patterns, i.e. volume in cum. per borehole. As such, higher drill productivity and higher production from the given number of holes can be achieved by adopting appropriate energy content in explosives, and suitable drill pattern for getting desired fragmentation.

Jan 1, 1998

By J T. Schamaun

Recent applications of explosives and blasting agents to rubble rock have led to requirements for more elaborate design and analysis methods. In most blasting uses, it is necessary not only to fracture the rock, but also to move the broken rubble in a predictable manner. Many in situ extraction techniques require; rubblization to take place in a confined region where rock motion is a predominate factor in creating a permeable broken bed. In this paper, an engineering model is presented which describes the large rubble motion during blasting. This model is intended to provide the blast designer with a tool for evaluation and further refinement of blasting patterns and timing sequences.

Jan 1, 1983

By George D. Raitt

Anyone who has spent any time in and around the drilling and blasting profession knows that probably the most critical part is the drilling portion. A blasthole is nothing more than a cylindrical vehicle designed and strategically situated to hold and contain an explosive charge so that it can be detonated in the most efficient and optimum manner possible. It matters very little if the latest “State-of-the-Art” explosive or detonation system Is employed if the hole is poorly placed; i.e. excessive burden and spacing, sized incorrectly for desired results, insufficient in depth etc.. This is not to mention that the drilling phase is the most expensive, requiring sizeable initial outlays and upkeep. It’s also true that improper drilling can cause costs to skyrocket throughout the remainder of the work cycles such as excavating and hauling, crushing, screening and so on.

Jan 1, 1990

By D Linn Coursen

Detonation propagates in the subject blasting agent at about 2.7 km/sec when it is heavily primed but explosion propagates in it at only about 0.43 km/sec when it is lightly primed. When propagating at 0.43 km/sec, it produces a borehole pressure that is slightly less than 1 kb, but no yellow fumes or other sign of incomplete reaction. It is a pumped AN/emulsion blend to which additional water is added by circumferential injection at the inlet of the hose through which it is pumped.

Jan 1, 1994

By S C. Alford

Explosive fracturing of metal is usually considered to be an imprecise process but, by careful consideration of shock-wave geometry, precise results are obtainable. The limited development of such charges is attributed to experimental difficulties. A charge configuration has now been devised in which a prismatic wave-shaping element is used to resolve the shock-waves entering a target plate into two convergent components. The extreme pressure caused by their collision initiates a diamond fracture in the proximal target face, and coincidence of reflected tension waves generates a fracture in the distal face. A combination of these effects breaks the target. An embodiment of S.R.T. is described which is flexible, magnetic and contains no cavities.

Jan 1, 1986

By Erik Nygaard

Ammonium nitrate (AN) is the main ingredient in most industrial explosives, but it is estimated that as much as 80-90% of the global annual production is used as fertilizer [14, 25]. Over the last years AN has been involved in several accidents and used in criminal bomb making. Therefore authorities and legislators worldwide have given it special attention. This paper is divided into three parts: • The first part will focus on the accidents with AN that have occurred over the last years and possible scenarios based on official investigations. • The second part covers safety and security related issues. • The third part will summarize new legislation that is coming both within European Union (EU) and also on a global scale.

Jan 1, 2006

By Melvin A. Sannes

The explosives industry is recognized as one of the most dangerous occupations in the world, yet it is rare to see actual training procedures. As our industry becomes increasingly technical, it is imperative that we train the personnel in OUI industry properly.

Jan 1, 1999

By Qingshou Chen, Gongbo Li, Hengqian Ran

A method for safe fracture of rock, concrete and other brittle solid material using dynamic water pressure by explosion is provided. The propagation of the pressure is studied with Allievi water hammer theory. Wave equation and velocity formulas of the pressure propagation are shown. The dynamic water pressure is tested in the lab. The propagation of the pressure is simulated by MMIC-2D. The results of fracturing rock in the lab and on a quarry are presented.

Jan 1, 2000

By Petr Mostak, Miroslav Horacek, Miroslav Stancl

Detection of plastic explosives is an important task in the security measures against criminal misuses of this type of explosive. Particles and vapour detectors are basic instruments in this detection. Colour reactions and dogs are also used. Marking system in accordance with requirements of Montreal Convention was developed and applied in full scale production of plastic explosives including Semtex since 199 1. The influence of marking on technology, performance and other properties of plastic explosives is discussed. 2,3 dimethyl 2,3 dinitrobutan is the most popular marking agent which is broadly used. The detectability of this compound is not optimum by some detectors. The substantial effort has been given to development of plastic explosives with controlled shelflife. Some results of this work are presented. Technical and economic aspects of identification marking are discussed.

Jan 1, 2001

By X Meng, W. A. Hustrulid, M. K. McCarter

Rock excavation in both surface and underground mining is largely accomplished using the drill and blast technique. At the perimeter of such excavations, cautious blasting procedures are often employed to minimize unwanted damage to the remaining rock. Of the several different techniques available, the use of explosive charges with a diameter smaller than the holes in which they are introduced (so-called decoupled charges) is the most common. In spite of the long and widespread use of the technique, a technically sound basis for relating the borehole wall pressure to the explosion pressure is still lacking. Such a relationship is required for optimal design

Jan 1, 2005

By Ulrich Leiste, Andrew Wardlaw, William Fourney

This paper describes the loading on a plate suspended directly over an explosive charge submerged in water. This problem is of interest because it yields results similar to those obtained in the detonation of an explosive buried in saturated soil and thus it is associated with landmines. Recent experiments [1] indicate that plate loading from a submerged charge is similar to that for a buried one, with respect to impulse and pressure. Compared to the buried explosive problem, the submerged explosive case is attractive from a computational point of view; it replaces sand, which is diffi cult to simulate, with water, whose properties are well known. Studying this problem allows modeling uncertainties to be separated from sand simulation issues.

Jan 1, 2008

By Roger Favreau, Patrice Favreau

Without blasting there can be no roads, no hospitals, no factories, not even foundations for homes. Yet in 1960 the only way to design a blast was by trial/error. By comparison, bridges were already designed by calculations before being actually built. This was possible because equations based on the fundamental principles of science existed with which all the stresses in the bridge could be calculated. In 1960 no equations based on the fundamental principles of science existed with which the mechanisms that take place inside the rock mass during a blast could be calculated. Since then the main author made it the objective of his research to seek such equations, and to validate that they gave accurate answers by means of experiments in the field, experiments made in co-operation with mines, quarries and the explosives industry; results have been reported in some 90 publications.These equations now deal with essentially all aspects of a bench blast: the intensity of the shock wave and the fragmentation size distribution throughout the rock mass; the movement of all the fragments into the muck pile; the fly rock and vibrations from the blast; etc.; are presented examples of such equations. They are now assembled into a computer simulator called Blaspa accessible on the Web, with which one can design a blast just as a bridge is designed. An example is presented. The reason to design a blast by simulations rather than solely by trial/error is that if it leads to damage, it is only after the actual blast that the blast design is realized to cause damage. If however the blast design had been simulated before the blast, then the risk of damage is identified before the blast and is prevented by redesigning the blast. Examples of such situations are presented. The need to a void damage is very necessary because the public is becoming opposed to blasting. When a blast does cause damage, and people learn that the blast was designed solely by trial/error even though simulation was available and would have prevented damage, they become even more strongly against blasting; they may succeed in getting a quarry closed. Their objections to unchecked blasting are not unreasonable, especially as simulating a blast with Blaspa on the Web is a very simple procedure.

Jan 1, 2013

By Chantale Doucet, Mario Paventi, Malcolm Scoble, Yves Lizotte

Laboratory studies in homogeneous material indicate that the area of new surfaces created by blasting is proportional to the energy imparted to the material. Field studies, however, show that fragmentation is also related to the rockmass structure. This paper reviews ongoing compilation of a comprehensive and integrated blasting database which is based upon field monitoring and laboratory testing. A priority application of the database is to support attempts to more fully understand structural control over fragmentation. Database construction and the relative importance of rockmass physical and mechanical properties are considered in the paper. A methodology for data collection prior to, during and after blasting is reviewed. Data summaries from three case studies of blast performance in surface and underground mines are presented. These illustrate various aspects of the methodology, which included image analysis to quantify the fragment shape and remnant geology evident in the muckpile as part of the evaluation of structural control over fragmentation.

Jan 1, 1994

By D Wilson, E Nagy, R A. Augsten, R R. Vandebeek, R L. Guilbeault

The Canadian Explosives Research Laboratory (CERL), is evaluating the status of the Schedule IV explosives container as it presently pertains to the industry. The Schedule IV container serves the same purpose in Canada as the IME 22 container does in the United States. That is, to transport detonators on the same vehicle which is carrying explosives.

Jan 1, 1990

By R A. Farnfield

Measurement of the environmental impact of ground vibration from blasting operations is based almost exclusively on the peak vibration level generated. This measurement is known as the Peak Particle Velocity or PPV. The recorded PPV is used to assess the impact of the vibration both in terms of structural damage and human response. Limits for vibration are almost universally quoted in terms of PPV levels and, as a consequence, blast design for vibration control is centred around techniques for the control of this peak value.

Jan 1, 1996

By Kaushik Dey

Bord and pillar is the most predominant method of wining of coal in Indian underground coal mines. Development heading in coal mines often encounters roof stability problem and results in roof overbreak. Research on this reveals that the blast-induced ground vibration may have significant contribution in roof overbreak, especially, when solid blasting is carried out in the bord and pillar method. Solid blasting, in general, is associated with higher charge confinement due to lack of free face and generates higher ground vibration, which in turn results in excess overbreak.

Jan 1, 2008

By D. Goodings, W. L. Fourney, Bonenberger, R., Uli Leiste

The problem of the maximum depth at which a mine buried in the surf zone or beach zone is a threat to landing vehicles is being studied by Naval Surface Warfare Center (NSWC), Indian Head Division, Naval Research Laboratory (NRL), and The University of Maryland Dynamic Effects Laboratory. The problem was divided into two parts: The first part involves determining how deep a pressure plate mine can be and still detect a vehicle passing over it. This requires determining the distribution of stress within dry and saturated sand when a vehicle passes over a buried mine. The results obtained from that study are presented in a related paper (1). This paper will cover the second part, which entails determining the impulse delivered to the vehicle. This is equivalent to determining the impulse delivered to a plate suspended above the detonating explosive charge and includes an investigation of the distribution of the impulse over the plate. The purpose of the research is to develop a scaling law and/or computational capability which will permit predicting impulse to be expected in the field from tests conducted in the lab. The computational effort is aimed at the development of and confidence in computer codes that can be used to predict stresses and strains in plates due to the detonation of buried mines.

Jan 1, 2004

By Mark Mammele, John Bowles

With the continuing rise in the cost of petroleum products and the focus on the increasing use of renewable resources, a readily available, economical replacement for fuel oil in ANFO is the logical next step, and has finally come to realization. This “green” fuel is plentiful, derived from renewable resources, more cost effective and reduces CO emissions. It also increases product density and bulk strength performance. As this unique fuel replaces some of the mass of ammonium nitrate prill, increased savings will be realized proportionally with the increasing cost of ammonium nitrate. Minimal changes are necessary, as this renewable fuel is designed for use and handling with current, commonly used ANFO blending and loading equipment. This proven technology is now in use by commercial operations in the Southwest, providing significant economic benefit with reduced cost per hundred weight of ANFO consumed.

Jan 1, 2008